Card PCMCIA not recognised on Satellite P100

Similar Questions

• Satellite Pro 430 CD: card wifi PCMCIA not recognised

  I have this laptop old which is still in occasional use. It is already updated for Windows 98 SE and working reasonably well even so naturally more slow. I had considered to connect to a wireless router with a Wireless PCMCIA network card. Installation and implementation is supposed to be a simple but not quite simple procedure, because it does not work. Two PCMCIA slots are functional because they recognize and allow operation of the PCMCIA modem to access remotely.

  However, the wireless network card is not yet recognized, and reading for the two slots indicates empty state. The map has been tested on another more recent laptop and is fully functional. Does anyone know if the old machine that above is even able to deliver what I'm trying to get by? The configuration required by the supplier/manufacturer of the card is a PC-compatible computer with a compatible CardBus 32-bit slot available and the operating system is Windows 98 SE, I have. It is possible, that I expect a lot of this old machine, can one through some light on the subject?

  [Edited by: admin]

  Hello

  I found information that your device can use 2 x PCMCIA Type II or 1 x PCMCIA of Type III. In my opinion, you should check your device specifications and there must be information law which PCMCIA card you can use with it (16 or 32 bit).

  Also, I found a very interesting site on standards and PCMCIA cards. If you want you can check it out on http://www.sycard.com/pcard_qa.html.

• Second FireWire PCMCIA card does not work on Satellite A110-178

  Hello!
  I tried to use the PCMCIA card as the second controller FireWire from different producers, but they can't take it.
  Sweex - PCMCIA Firewire kaart
  laptop computer en PCMCIA USB FireWire 1394 Combo CARDBUS

  I really need the second FireWire controller on my Toshiba Satellite A110-178.

  Thanks Ben

  Hello

  The Satellite A110-178 PSAB0E supports a Cardbus 32-bit / PC - Card 16-bit slot and you can ONLY use cards PCMCIA type II

  Please do not forget that your PCMCIA firewire card supports hardware specifications listed above.
  If not; you will need to purchase another compatible!

  Best regards

• XP audio driver does not work on Satellite P100-106

  I reinstalled Windows XP on my Satellite P100-106 and all the works of good drivers.
  Only the audio that I can not install driver.
  The problem is that my sound card changes the name, and I don't really know how his happened?

  His name was sound card Conexant high definition and now its something to gibrish... (something not readable)
  http://i44.Servimg.com/u/F44/12/54/24/92/error10.jpg

  I tried to remove the material in the hardware Manager, but again, the name is always the same.
  So, what should I do?

  Thx a lot eric.

  It seems that this has been resolved before, look for the satellites «Sound P100» P series

• SD memory cards are not recognized on satellite A200

  Hello!

  I had a Satellite A200 installed with Vista.
  When I insert the SD card into the laptop, nothing happens. My SD card does not seem to be recognized by the system.
  I tried to different maps, but none of them have been recognized.
  SD host controller is listed correctly in the Device Manager.
  I don't know what happened, but there is no problem with SD cards before you recognize.

  Thanks in advance!

  Hi there, my suggestion would be first uninstall and then reinstall the drivers from your SD controller (available for your laptop model on your regional site of Toshiba drivers). If this does not resolve the problem, then visit the following link to download an update to enable playback of higher capacity SD cards under Windows Vista: http://www.microsoft.com/downloads/details.aspx?FamilyID=e42fc131-6a76-4b27-934a-fb19dd323dab&DisplayLang=en if this fails, then make sure that you are upgraded to Service Pack 1 of Windows Vista.

  I hope this helps

• Silent CD/DVD drive acoustic does not work on Satellite P100-194

  Satellite P100-194 (Win XP MCE, Bios-Version 2.20)

  Given that excessive vibration of the drive DVD-Multi-with some of my DVDs and CDs, I would not use the acoustic silencer, but West no difference between Silent Mode and Normal Mode.

  I tried to reinstall the silent acoustic tool, without success. As this problem starts to get really annoying, any help would be appreciated.

  I wonder if the built-in-multi-DVD player is sensitive by default (sometimes entire Notepad starts vibrating combined with a noise level very high during playback of a dvd)?

  Thanks in advance!

  Hi WB,.

  I think that acoustic silencer simply limited the rate at which information can be obtained on CD/DVD in order to prevent the rotation high speed that can sometimes occur when extracting the CD or the DVD to the hard drive. If you're just watching DVDs (or listening to CD, by the way) then the speed of the drive will be not particularly high because once the buffer is full so there is no need to read more data from the disc itself. If you look at the car LED, you'll see that it only lights intermittently ever.

  The speed of the drive will decrease during playback, as the laser reads information from the outer part of the disc surface.

  The presence of noise and vibration normally indicates that the disk is "eccentric" or is not set centrally in the reader, and this may indicate a possible problem with the clamping mechanism itself. However, it is always worth checking that the center hole of the disc itself has no Burr or pieces of materila which he would lift off, and it is also useful to check if the label of the disc (assuming that it is a type of stick on paper) is properly attached and has no loops or bubbles in it since this may also cause noise of air.

  I have the experience of a couple of game of CD-ROM discs that cause a lot of noise and vibrations in my book and recording, I found that the central hole was slightly shifted.

  Kind regards

• DVD - R is not recognized on Satellite P100

  I tried to read the DVD-R on my satellite P100-188, but when I insert a disc the player does not even recognize that its there and comes uo with the message "insert disk".

  Any ideas as its very frustrating?

  Thank you

  Post edited by: [email protected]

  Hello

  You have this problem with original DVD?

• System Recovery works do not with my Satellite P100

  I followed the instructions I saw on many sites to be able to do a system restore to 'out-of-box"State. I've maintained pressed zero and hit the key on and then release the zero key when I hear the beep. After that it only gives me the possibility to proceed to the recovery of the system. It starts just as usual.

  What I am doing wrong?

  Hello Shae

  How to start now? OK Let's ' s go!

  Toshiba recovery procedure can be done with recovery CD/DVD or facilities using images stored on the HARD disk. Image stored on the HARD drive will be offered with the new notebooks only and I am sure that your Satellite P100 is delivered with a CD/DVD media and not the HARD drive recovery option.

  AFAIK this option 0 is for HDD only installation. Please note that this option 0 is not also for all Toshiba laptops. For European books, you can start installation disk with F8 and not 0.

  I hope you understand how this works now. The question is what P100 you have exactly and how you are trying to install OS? You want to use Toshiba Recovery CD/DVDs?

• Wireless card is not on the Satellite C650-15U

  Hello
  I have a Toshiba Satellite C650-15U, this morning I tried to connect to the Net via wifi, but I saw that there is no connection. In Control Panel, there is no WiFi card, it seems to me that I have no card wireless at all!

  When I tried to reinstall the driver, the message: «card wirless not...» "is displayed. the only way to connect to the net is the cable.

  Can someone help me please.

  Can you enter check and if Device Manager card WLAN is in the list?
  Control Panel > system > Device Manager

  It should be listed under network adapters.
  Maybe some unknown device appears in Device Manager?
  Which driver you tried to install?

• PCMCIA card will not install on Satellite L30 - 10y

  Hi all

  I hope someone can help with this problem. I recently bought a PCMCIA card with additional USB ports for my laptop Satellite L30 - 10y. It works on Vista basic, anyway I shoved the card into the slot and let windows install the drivers, problem is it will not load I get an error message saying that the MDT-0002 device does not charge.

  Is it a Vista problem or Toshiba thing?
  Thanks for any help on this one
  Regards Ciaran

  Hello

  I doubt that it could be a matter of Toshiba.
  I googled a bit for this device MDT-0002 error, and this error using some PCMCIA cards on different laptops from different manufacturers under Vista OS.
  Someone said that the Pcmcia.sys (PCMCIA driver) must be updated.

  I also recommend to contact manufacturer of PCMCIA card support for more details on a few issues with the Vista operating system.

  Welcome them

• Ethernet network card does not show my Satellite L830 - 16H

  Hello

  Ethernet network adapter do not show my Toshiba Satellite L830 - 16H, and it can not reset it

  What can you do to restore it?

  I thank everyone

  You can try to access the BIOS (turn the unit on and press F2) and set it to default and save the changes.
  Sometimes this help

  Otherwise, it can be device LAN card problem.
  The fix can be very expensive because such port is part of the motherboard.

  I think you can try using an optional USB LAN RJ45 Ethernet adapter

• SD 2 GB card is not readable on Satellite P10 504

  I have a satellite P10-504 P4 2.8 GHz/XP with an SD card, when I insert a 2 gb SanDisk sd card it does not read.
  What could do?
  I think that of something maybe drivers upgrade, but I cant find it anywhere.

  Hello

  Unfortunately, the reader doesn't support this format SD card and you will find all the drivers for the SD card. The operating system uses the standard Microsoft drivers.
  In your case, the best way is to buy the external USB card reader supporting multiple card formats.
  Such device simply isn't very expensive ;)

• Need a card PCMCIA Firewire for a Satellite P30

  I need to use a PCMCIA Firewire card for download Mini DV video from my camcorder Samsung - any recommendations?

  Here is a list of amazon

  http://www.Amazon.co.UK/s/ref=nb_ss_ce/026-4958504-1587658?URL=search-alias%3Delectronics&field-keywords=PCMCIA+FireWire

  Thank you

  Hi new friend :),

  I hope that you could get some information in another post, it was not necessary to open a new topic. But anyway, I looked at the link you gave and
  Yes, that ' s´s exactly what you´re need.

  So don't hesitate to buy this PCMCIA Firewire card and use it with your DV - Cam to record videos.

  If you have any questions just "do it" (ask) :)

  Greetings

• Built-in Bluetooth does not work on Satellite P100

  I installed everything the package of bluetooth on my P100. It is written + BT on the back of my laptop, but I am not able to see it on my pilot system. I followed http://aps.toshiba-tro.de/bluetooth/redirect.php?page=pages/faq/bluetoothnotworking.html

  but I don't understand why nothing works. I tried (and disintall after) a USB bluetooth and it works perfectly.

  Can you help me?

  If this unit supports the BT and BT card is inside, so all drivers Bluetooth were pre-installed.
  Choose the Bluetooth with FN + F8 to use BT.
  Then the BT icon should appear in the status bar.

  Then if you want to use it you must activate the 3rd BT device and you have use the coupling function.

• 2 GB card SD not recognized in Satellite Pro 6100

  Hello

  I got a new 2 GB SD card passenger high speed. When I insert into the slot of my Satellite Pro 6100 SD card, I see in the list of the Explorer, the new drive, but when I click it, it says: "Please insert card".

  The card works fine in my Pocket PC.

  What can I do? What is the size limit of card for the SD-Card-Reader inbuild?

  Any help is appreciated!
  Thank you!

  At the point where Satellite Pro has been offered, there was no 2 GB SD card and card reader has been tested with available maps only. If you're lucky, 1 GB card can be readable.

  I think you this card works fine in the other device. There is absolutely no problem with the card itself but old material or even driver for the card reader.

  Maybe in the next few days, someone will point out what card can be used with SP 6100.