CD not recognized in the drive when burning music

Similar Questions

• Ok. so, when I sync my music to the ipod, it can read my computer to play, but it is not recognized as the device when I unplug it from the computer.

  my ipod plays only a few original downloads on my sound surround of boise, but the most recent downloads will only record and play on my computer. When I download music it synchronizes and can be found and played back on the computer but is not found on the actual screen of the ipod to play my biose surround sound, but there is space on the ipod.

  If you wait for the new songs (in your iTunes library) to automatically synchronize to the iPod, it must be configured to use automatic synchronization (setting synchronization music ).  Select iPod in iTunes by clicking on its button on the device.  For current iTunes, the screenshot below shows top left corner my iTunes, iPod touch window circled in red.

  

  Click this button to display the settings of the iPod summary screen in the iTunes window.  Along the left side of the window, in the sidebar, under settings, click on music.  To the right, the music from the iPod settings screen.  Check mark for Sync music box (if it isn't already)

  NOTE: No matter what songs on iPod that are not in your iTunes library (on computer) will be lost.

  This enables automatic synchronization.  You can choose to synchronize the entire music library (if it fits on the iPod) or a part of the selection .  Implement this screen as you want, and then click apply.  Further, iTunes automatically keeps iPod "in phase" with the changes to your music library (or the selected part of it) when you connect the iPod (or click sync , if already connected).

  If this isn't your problem, please post back with additional details.

• computer laptop power adapter / battery not recognized by the laptop when connecting

  Please help I just buy a new battery it works fine but I realized that when I unplug the adapter and put it back again when the tower is on it does not recognize it and when I turned off the computer and put it... it will normally recognize and keep on even though I started the computer, but if I just remove it and put it once again it is the same thing again and again... I have compaq hp c740EE windows vista

  Hello

  Could be a BIOS problem. And it is more likely to be the charger circuit that the
  battery although anything is possible. Definitely check with the support of Compaq and ask
  in their forums because this could well be a known issue with a hotfix.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• A SSD from OCZ Agility 3 disc works with a dv9700T? Mine is not recognized by the BIOS.

  I bought a 120 GB OCZ SSD Agility 3 disc to install in my laptop the dv9700T CTO.  The drive is not recognized by the BIOS when it is installed in the Bay of 1 or 2, but is recognized when connected via USB as a secondary drive.  The drive works fine in a different computer, so I know the drive works.  There seems to be a problem with the SATA (ICH8) controller.

  Someone at - it any information on that?  Would love to get the drive works in my laptop.

  Thank you.

  Lloyd

  If you have a HARD drive installed in the secondary Bay and the OCZ SSD in the first Bay, the dv9700t starts and works very well.

  Lloyd

• Why do my windows media sometimes not recognize that there is a disc in the drive when I am trying to burn music on the disc,

  Original title: windows media problems
  Why do my windows media sometimes not recognize that there is a disc in the drive when I am trying to burn music on the disc,

  If you restart WMP when this problem occurs, which helps?

  It seems that the AutoRun or AutoPlay got disabled on your system. Please try the instructions in the following article to reactivate these:

  http://support.Microsoft.com/kb/330135

• External hard drive is not recognized and the Table to Partition GUID (GPT) partitioning scheme has message is required (-69773)

  Hello!

  I have an external HD that has been unplugued without eject by mistake. Since then, the HD is not recognized by the finder or disk utility.

  When I list the disk in the Terminal, the drive is listed.

  But when I tried to check or repair, a message appears: "failed to check this disc: a Partition GUID (GPT) partitioning schΘma Table is required (-69773).

  I can access the files using programs such as Seagate File Recovery, but I want to extract data and repair the disk without using 3rd party software.

  Is this possible?

  If you have access to the files - a possibility would be to get the files off the disk and then reformat using disk utility

• HARD drive is not recognized on the Satellite 2800 200

  Hello

  First of all, I'm Dutch so I hope that I do not have too many mistakes in my English writing.

  I bought a 2800-200 Satellite at a friend's House. This laptop has a problem.
  When it is started is says "insert the disk in the drive system. Press a key when readya?.

  My bios is ACPI BIOS version 1.80
  In Pheripheral in Bios it says disc hard = not used Mode.

  On page two discs i/o: HARD drive: no drive.

  I tried two hard drives and the two were not working and not recognized in the BIOS.
  I have no CD of restoration.

  My questions:

  What kind of central computer has this laptop?
  Can someone help me with the recovery CD?
  What can I do to fix this?
  How can I change my BIOS so that the HARD drive is recognized?

  My hard drive is MK2023GAS and is not broken. There is nothing on this HARD drive.
  But also with the disk hard 10 GB of origin, I had the same problem.

  I hope you can help me and once again I apologize for my English.

  Hello

  I'll try to help you my friend.

  > When it is started is says "insert the disk in the drive system. Press any key when ready
  This message appeared on my laptop after the HARD disk is dead.
  I had to replace the HARD drive and reinstall the operating system.

  I guess that it of the same problem with your laptop. The HARD drive is not present or not recognized, and you will need to install a compatible HDD for the operation of the OS.

  I have google a bit and discovered that this laptop comes with the 10 GB HARD MK1016GAP of Toshiba drive. It supports the interface ATA-2/ATA-3/ATA-4/ATA-5.

  Please note that many BIOS have a limit of size of HARD drive. This means that not all HARD drive sizes are supported! I assume a 20 GB should be compatible, but this is just my own opinion
  > How can I change my BIOS so that the HARD drive is recognized?
  The BIOS can be modified outside the update (check page driver Toshiba-> Archive-> archive of Satellite).
  But vary important is that you use a compatible HARD drive.

  > Can someone help me with the recovery CD?
  Don t know if you will be able to order this CD at the service provider allowed in your country, because the laptop is really an oldie. But you should ask the guys.
  What you is to install the OS from the Microsoft CD-ROM and then could install drivers needed.

  Greetings

• Hard drive is not recognized in the BIOS - Equium A60

  Hi hope someone can help. I have a Toshiba Equium EA60-173 and the hard drive is not recognized in the BIOS. When I remove the hard drive and put it in another laptop it is detected fine. I also tried another hard drive in the Toshiba and that does not work either. So I suspect the IDE controller has disappeared, but can I do to confirm this? I wish there was an option in the BIOS to force detection. I updated the BIOS but still the same.

  This laptop is only just out of warranty, so if it is the controller would I need to replace the motherboard? Are there other options at my disposal?

  Thanks in advance.

  Hi Neil,

  Unless there is some physical\problem with the cable/connector hard drive, then it is most likely that you will have a new mainboard for your laptop. I suggest you to contact an authorized service partner and ask them to check your laptop and give you an estimate of the cost of the repair. Then you can try to shop for less expensive alternatives.

  Kind regards

• niDMM.cs exception: "the device was not recognized. The device is not supported with this driver or version. »

  Hi all!

  I have a question about using a DMM (PXI-4065) with VStudio 2008 and Measurement Studio 2009.

  Because DMM are not always supported in .net, I downloaded niDMM.cs 3.0 wrapper of the web site of NOR.

  I also downloaded example c# measure DC Voltsto compare with my request.

  Both an example and my application fail trowing the exception [-1074118656] 'the device was not recognized.  The device is not supported with this driver or version. " class constructor is called.

  DMM = new InstrumentDriverInterop.Ivi.nidmm ("PXI3::12:INSTR", true, true);

  I guess it is function of device PXI!

  I also tried to use a VISA alias as "pippo" and then I tried to insert a device unexistent name. In any case the same exception was trown.

  NOR-DAQmx 8.9.5

  NOR-DMM 3.0.1

  NI-VISA 4.6.1

  NOR-MAX 4.6.2f1

  Roberto

  Hello Robson,

  Maybe you areusing an incorrect descriptor itrument, try please the instructions contained in the following document:

  KB 33A96PCW: receive error-1074118656 when running OR DMM screws

  Let me know if this might help.

  Best regards.

• I found that if it becomes necessary to use time machine to return to an earlier existence to reinstall the iphoto library, if for some reason, you lose lose, then when you try to synchronize your ipad is not recognized by the computer.  As one

  I found that if it becomes necessary to use time machine to return to an earlier existence to reinstall the iphoto library, if for some reason, you lose lose, then when you try to synchronize your ipad is not recognized by the computer.  So when you try to synchronize the pictures, they are all removed from the ipad and trying to reinstall everything again.

  This may or may not work immediately.  In my case, only half the photos have been installed, and then the error message came that the rest of 9000 can be installed.

  I contacted Apple support team who has made various suggestions.  Subsequently clicking on a photo list in iTunes were all going again and pictures of 9000 then installed.  When I asked the support team what could happen I was told that it was a "glitch".  I don't like seeds they mean that there could be an error in coding somewhere.

  Here me again.  I use an iMac and iPad.  I don't know why XP and iPhone came.

• Keyboard Dell Bluetooth is not recognized when energy savings and will not wake my computer. My usb mouse not recognized or the other.

  My Dell Bluetooth keyboard is not recognized when energy savings and will not wake my computer. My usb mouse not recognized or the other.  I use keyboard now, but it seems not be installed yet when I check my keyboard or bluetooth devices. Keyboard does not work after so I'll try to figure out what to do before moving into the power saving mode. Help, please. I did all the updates from microsoft, and there is no update for my bluetooth device, I checked.

  Hello

  1. have you made changes on the computer before this problem?
  2. What is the model of the keyboard?
  3. are you an error message or error code?
  4. which version of the Windows operating system is installed on your computer?

  I suggest you to consult the following Microsoft article and check if it helps.

  On troubleshooting in Windows 7 power management: http://support.microsoft.com/kb/980869

  Troubleshoot keyboard: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-keyboard-problems

  Keyboard and Microsoft mouse refer:

  Troubleshoot the incidents of the response to the mouse or wireless keyboard: http://support.microsoft.com/kb/838398

  Reference:

  Troubleshooting external Dell Wireless or Bluetooth keyboards and mice: http://support.Dell.com/support/topics/global.aspx/support/KCS/document?docid=277550#Issue0_1

• HP Officejet 8500 A909g is not recognized by my computer when plugged into the usb port

  I received an email from HP recommend I install new software for my Officejet Pro 8500.  I downloaded the software and installed.  The printer was working, but it would not scan. I got an error message telling me to re install the software because the analysis part has not been installed. I have downlaoded software again and installed it. During installation, the mode had to unplug the printer, so I did. (It is connected using the usb cable directly to the back of the computer).  When installation instructions came at a certain time, it told me to plug the printer. I did, but it was not recognized.  I checked the box to install all the software and install the printer later.  Now is back, and the printer is still not recognized by the computer.  Help, please.

  Hi Steve_finch,

  What operating system you have installed on the computer?

  Have you tried a new USB cable or a USB port on the computer?

• I recently bought a Canon 5 d camera SR and when I imported the photos taken in Lightroom RAW gave me the following message: "files are not recognized by the RAW format support in Lightroom (73)" what should I do?

  I recently bought a Canon 5 d camera SR and when I imported the photos taken in RAW, Lightroom gave me the following message: "files are not recognized by the inLightroom of support for the RAW format (73)" what should I do?

  Hello

  Looks like you may not have the latest version of Lightroom as the Canon 5 d R raw files are supported in Lightroom 6.0 and above (not in previous versions)

  Devices supported by Camera Raw

• Portégé R700 - 15L - 3 G is not recognized by the system

  Hello

  I already bought this laptop and I have problem with 3G driver to work.

  I downloaded the latest drivers from the website, but the device was not recognized by the system?

  Any ideas how to fix?

  Best way to fix this is to install the original OS, you got with this portable Portege. Original recovery image contains all the necessary drivers and tools and utilities.

  When you use the FN + F8 key combination what options are available?

• HDD and dvd are not recognized in the configuration menu, what could be the problem?

  The hard drive and dvd drive are not recognized on the configuration menu for my desktop Pavilion a4316f.  What is a controller failure?  A PCI controller can be used to replace the motherboard controller?

  dhobs,

  Anguish, that the suffering of the faulty motherboard has been aggravated by your actions. Why you decided to perform a restore (which re - formate the disk, erase all your data files (documents, photos, videos to misic,) is really amazing.)

  You had a viable BONE, work and the data store. You he clobbered with recovery. As explained, the 'tattoo' reads the embedded hardware configuration and will stop at the resumption of treatment if it detects a change.

  Only temporary help I can offer is to open the computer case and install a small 12v on the NVidia chip fan. IF the chip is not 100% burned, you can earn low enough time to reinstall the operating system and then add the map.