Change the color of the quick mask

Similar Questions

• How do you change the default mask rubylith color?

  Anyone know how to change the default mask color permanently? I have never want this bright red default "rubylith" and am so tired of having to change color every time I do a new mask! (This process takes 6 clicks!)  I just want it to be automatically my default color.

  Double-click the button quick mask (button down in the toolbar)

• Cannot change the subnet mask of eCard in 7.1.3 (opensuse 11.4)

  Had this problem before with 7.0 on suse 11.2, but I forget how I "fixed it". This is quite irritating considering I found nothing on google about this topic. I hope it's just my ignorance with the software and not a real problem, but when I try to change a vmnet as Host-only adapter, I have no option to change the subnet mask. I've seen tutorials where you just have this option, but I did not.

  I use a very simple script to make changes to the Infrastructure virtual VMware which are not available on Linux hosts via the virtual network editor in Linux in VMware Workstation version.  Note that there may be other ways, but this is what worked for me.  Also note that changes to the value of a parameter that is not a correct value will cause failures, and that's why I have the scrip, run the commands with the talkative and check the ifconfig and VMware Network Status before and after you made the changes and you will see that in the attached script.

  If you do not have what it takes to use the attached script then in a Terminal root or with sudo:

  sudo /usr/bin/vmware-networks --stop -v
  sudo cp -p /etc/vmware/networking /etc/vmware/networking.backup
  sudo cp -p /etc/vmware/vmnet1/dhcpd/dhcpd.conf /etc/vmware/vmnet1/dhcpd/dhcpd.conf.backup
  sudo cp -p /etc/vmware/vmnet8/dhcpd/dhcpd.conf /etc/vmware/vmnet8/dhcpd/dhcpd.conf.backup
  sudo nano /etc/vmware/networking
  sudo nano /etc/vmware/vmnet1/dhcpd/dhcpd.conf
  sudo nano /etc/vmware/vmnet8/dhcpd/dhcpd.conf
  sudo /usr/bin/vmware-networks --start -v
  sudo /usr/bin/vmware-netcfg
  sudo /usr/bin/vmware-networks --start -v
  

  In the attached script, you will see the following note about the use of writing, or why this is done manually:

      # NOTE: Load the VMware Virtual Network Editor and then click the OK button.
      #    This is being done for two reasons, one is to validate the settings
      #    and the other is to create a new DHCP_CFG_HASH in the networking file.
      #
      #    Be sure to review the 'Current Status after editing...' for any errors.
  
  echo
  echo  Starting VMware Virtual Network Editor...
  echo
  sudo /usr/bin/vmware-netcfg
  

  As I said there may be other ways and VMware is unfortunately very tight secretive about what they do the document to be disclosed to the public, which is unfortunately very little.  It is so absurd that the version of Windows is not this limitation but I guess I would really be surprised since removed altogether VMware VMware Player for Linux virtual network editor and does not install it for the VMware Player for Windows even if it's in the Windows Installer Package. Go figure!

• Why foreground/background colors change when I switch to quick mask? I can't stop this change?

  I click on------, and the foreground/background colors switch. Why? How can I control this behavior of Photoshop?

  It would be simpler for my workflow of Photoshop that I knew what I was using the color.

  Hello

  In quick mask mode Photoshop automatically default gray scale, with a background of black and white, background color color mode. When you use a painting or the tool in quick mask editing mode, keep these principles in mind:

  • With black paint adds to the mask (the Red overlay) and decreases the selected area.
  • Painting with white clears the mask (the Red overlay) and increases the selected area.
  • Gray paint partially added to the mask.

  Thank you

• Why when I cut my selection of the quick mask in Photoshop it is suddenly just a cup a smaller version of the opacity of the image?

  Element selected and informed quick mask as usual:

  

  I'll CUT the selection and it cuts just a transparent layer off the coast of the image:

  

  And when I try to PASTE cuts the selection to the new document is just a transparent version like this:

  

  I never changed anything, so I don't know what happened or how to fix it! Help, please.

  you suggest to reset the Photoshop preferences and then try again.

  You can consult this article to restore preferences: helps Photoshop | Preferences

• Change the layer mask: Alt + Shift + click does not work?

  I have PES 9 w/Mac OS X.  According to Adobe using for layer masks, "to display the mask in a mask color red, hold down the Alt + Shift and click on the thumbnail of the layer mask".  It is also stated by Missing Manual for elements.  I can't get this to work and can display the mask only in itself (in black and white).  I have uninstalled/reinstalled without success.  In other words, when I change the mask, I don't see where I'm editing.  Can someone help me?

  Exit the editor, then go in your username > library > Preferences and delete:

  com.adobe.PhotoshopElements.plist

  Adobe Photoshop Elements 9 paths

  Adobe Photoshop Elements 9 parameters

  Repair permissions, and then try again.

• Cannot change the solder mask

  I want to erase a. 125 "wide strip the solder mask of ground plane on top of a circuit board in order to facilitate the soldering of a vertical metal shielding of the aircraft, but Ultiboard does not seem to allow this modification of the solder mask lind. Is there a work around?

  Thank you very much

  Hello

  Simply place a line on the soldermask layer. You can change the coordinates and widths on your needs. Welding layer mask is a negative layer in Ultiboard. Forms in the solder mask layer denote this solder mask must be set aside (or deleted) in this area. If there is no form in an area on the layer of soldermask, it is implied that physical solder mask will be applied during Assembly.

  If your Council Home supports a separate layer mask stick, you should double in the Sub solder with paste mask soldered to facilitate Assembly.

  Hope that helps.

• How can I change the quick launch programs?

  My model is g62-120ey. by default, the Quick Launch Media Player should launch CyberLink PowerDVD. How can I change this?

  Thank you

  http://QuickPlay.hostzi.com/

• Masks of brightness - cannot change the areas 'masked' by themselves

  I try to use luminosity masks in CS 5 Windows 7. I can create masks (there are enough tutorials on this part of the process) but when it comes to the use of curves to lighten/darken each mask, the entire image is affected. When I click on the BW cookie for the settings, a layer that adaptation is created, but the curves icon does not appear as I've seen and read about.

  
  

  In addition, when a mask is clicked on the RGB channel area, the new layer does not seem to align with the selected masks (1 light, 2 lights, etc.).

  
  

  My photography is mainly the work of railway and the sky is often a problem with too much light.

  
  

  I used Nikon but now have an Olympus L10... photos of both of them are good but want to change for all around goodness.

  BW cookie

  What is that supposed to be?

  the curves icon does not appear as I've seen and read about.

  The settings panel is open?

  In addition, when a mask is clicked on the RGB channel area, the new layer does not seem to align with the selected masks (1 light, 2 lights, etc.).

  You seem to try to verbally explain what could more easily be explained / showed issuing some screenshots.

• doubt on the Quick Mask mode?

  Hi I have 3 layers in photoshop.

  1. Background
  2. LAYER1
  3. Layer2

  Now on layer 2 I made a selection and entered in quick mask mode and then applied gussian blur. When this is done the selection borders trying to blend with the background, or will they try to blend with the layer 1 as is the layer just behind the layer 2. In case if there is no background, I mean if all three are diapers, then what happens?

  I have read the tute again and clarified. It will blend with the layer 1 image not directly with the background that is at the bottom of all the layers. In any case thanks a lot.

• Problems with the quick mask

  For unknown reasoning - and I'm sure that its not mind my tired old - I can't seem to hide images in quick mask mode using the brush. What I am doing wrong?

  Any help will be appreciated!

  Make sure the brush is 100% opacity and Normal mode.

• change the quick definition

  Hi all
  
  I created a command prompt of dashboard with an Aria of the object 'A' and I changed the name of Aria of subject to 'B', then the guest has stopped working. (I don't want to keep the topic Alias Aria)
  Since there is no Advanced tab in the quick definition I don't see how I can change the name of Aria of subject as I do for reports (go to the Advanced tab / change the name and press SQL Set).
  
  Can I change the name of Aria of object in the quick xml file, or it will damage the catalog?
  
  
  Concerning

  Hello

  Locate your command prompt in Catalog Manager. Double click or (right click > properties) > modify xml (top) > edit and you will be able to edit the xml code.

  Thank you
  Sandeep

  Published by: Teresa Sanchez on 09-Sep-2010 01:39

• How to change the quick font

  Hello
  
  
  I have need to change the fonts of the guest
  
  How to get there?
  
  
  Thax

  Hello

  You can't change the fonts of the guest directly. The solution is to
  Create two columns. SE MessageStyleText and one you need.
  Set the column class MessageStyleText CSS OraDataText.

  This column is the prompt for the field. You can set its value. In addition outside OraDataText you can use any other CSS class also according to your need.

  Changing the class CSS hope you know...
  How to change color Tip

  I hope I'm clear!

  Thank you
  AJ

• Reports 6i - how to change the format mask dinamicly?

  Hello

  I have a varchar2 with 10-digit field. The data represents a phone number. Example 5141231234, 4381231234, 21222253611, etc.

  I want to display them under the mask of specific format. Example (514) 123-1234, (438) 123-1234, 22 253 611 (212).

  How can I do it please?

  It is ok. I used srw.set_format_mask (my_format_mask); in a format trigger

• How to change the selection mask and layer image together?

  I have a newbie question.

  On Photoshop CS6

  I have a picture with a layer mask, which is related, as evidenced by the string between the image and the mask. I make a choice and try to apply a scale in free form, but I can only to scale the image or layer mask, not the two together. Don't seem much sense to me, everyone knows the answer?

  I have to set up a demo'ing youtube video my problem to make things clearer, link here: http://www.YouTube.com/watch?v=-Z6E98FZzMo

  Any help would be great

  Hello

  You only select the layer and not the layer with mask.

  Try this:

  With nothing selected, select the layer in the layer panel and then free transform.

  This should affect the layer and mask.