Cisco 1600i and 2504 Configuration problems

Similar Questions

• Satellite Pro 4600 and WiFi configuration problem

  Got a Toshiba Satellite Pro 4600, under WXP SP3. It s a P3 900 mhz with 256 RAM and it s a great laptop, but peut t seem to understand the Wi - Fi.
  It captures my router ok sky open a Wi - Fi connection, but it s the config, when I put the WEP key it says it is not compatible with WEP, WPA only s.

  I put the ssid for the router ok but it won t accept the key/passphrase in there it says s not long enough.
  Could someone point me in the direction of a guide of idiots for this configuration?
  Wi - Fi is built-in and it s a Toshiba mini PCI
  Thank you

  Hello

  For me the case sounds very clear;
  You can't put the encryption key just because the WEP key is not compatible / supported.

  I think you should use encryption that is supported by both parties; router and wireless network card

  Good bye

• Problem with the Cisco VPN and Vista client

  Hello

  I have an easy VPN server configured on a c2811 and users use the Cisco VPN client. Lately, I have users running Windows Vista 64 bit and I need to know what is the correct version of the vpn client, I have to use and the compatibility problems with the server, I configured.

  Thank you and best regards.

  Cisco VPN Client doesn't have any version that is compatible with Vista 64 bit OS. The only customer that Cisco has released that supports the 64 bit OS's AnyConnect, but it is only supported on the CISCO ASA Appliance

• Problem with IPSEC tunnel between Cisco PIX and Cisco ASA

  Hi all!

  Have a strange problem with one of our tunnel ipsec for one of our customers, we can open the tunnel of the customers of the site, but not from our site, don't understand what's wrong, if it would be a configuration problem should can we not all up the tunnel.

  On our side as initiator:

  Jan 14 13:53:26 172.27.1.254% PIX-7-702208: ISAKMP Phase 1 Exchange started (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-7-702210: Exchange of ISAKMP Phase 1 is complete (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% 6-PIX-602202: ISAKMP connected session (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-6-602201: Phase 1 ISAKMP Security Association created (local 1.1.1.1/500 (initiator), 2.2.2.2/500 remotely, authentication = pre-action, encryption = 3DES-CBC, hash = SHA, group = 2, life = 86400 s)

  Jan 14 13:53:26 172.27.1.254% PIX-7-702209: ISAKMP Phase 2 Exchange started (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-7-702201: ISAKMP Phase 1 delete received (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-6-602203: ISAKMP disconnected session (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:56 172.27.1.254% PIX-7-702303: sa_request, CBC (MSG key in English) = 1.1.1.1, dest = 2.2.2.2, src_proxy = 172.27.1.10/255.255.255.255/0/0 (type = 1), dest_proxy = 192.168.100.18/255.255.255.255/0/0 (type = 1), Protocol is ESP transform = lifedur hmac-sha-esp, esp-3des 28800 = s and 4608000 Ko, spi = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 4004

  The site of the customer like an answering machine:

  14 jan 11:58:23 172.27.1.254% PIX-7-702208: ISAKMP Phase 1 Exchange started (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% PIX-7-702210: Exchange of ISAKMP Phase 1 is complete (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% 6-PIX-602202: ISAKMP connected session (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% PIX-6-602201: Phase 1 ISAKMP Security Association created (local 1.1.1.1/500 (answering machine), distance 2.2.2.2/500, authentication = pre-action, encryption = 3DES-CBC, hash = MD5, group = 1, life = 86400 s)

  14 jan 11:58:23 172.27.1.254% PIX-7-702209: ISAKMP Phase 2 Exchange started (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% PIX-6-602301: its created, (his) sa_dest = 2.2.2.2, sa_prot = 50, sa_spi = 0x9de820bd (2649235645) sa_trans = sa_conn_id of hmac-sha-esp, esp-3des = 116

  14 jan 11:58:23 172.27.1.254% PIX-7-702211: Exchange of ISAKMP Phase 2 is complete (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  Jan 14 12:28:54 172.27.1.254% PIX-6-602302: SA deletion, (his) sa_dest = 2.2.2.2, sa_prot = 50, sa_spi = 0x9de820bd (2649235645), sa_trans = esp-3desesp-sha-hmac, sa_conn_id = 116

  Kind regards

  Johan

  From my experience when a tunnel is launched on one side, but it is not on the other hand, that the problem is with an inconsistency of the isakmp and ipsec policies, mainly as ipsec policies change sets and corresponding address with ASA platform when a tunnel is not a statically defined encryption card he sometimes use the dynamic tag to allocate this vpn connection. To check if this is the case go ahead and make a "crypto ipsec to show his" when the tunnel is active on both sides, see on the SAA if the corresponding tunnel is the static encryption card set or if it presents the dynamic encryption card.

  I advise you to go to the settings on both sides and ensure that they are both in the opposite direction.

• Configuration problem of the mixture of the regions with and without installation of persistence of the disc causing the JSONFormatter to fail

  I have trouble setting my local setup correctly with a mixture of regions with different configuration of persistence of disc.  Is a configuration problem on my end or a bug in GemFire and/or Spring GemFire data?

  The configuration of my work is as follows:

  < gfe: replicated-region id = "replicatedRegion" cache-ref = "gemfireCache" disk-store-ref = "overflowOnlyDiskstore" persistent = "false" >

  < gfe:eviction type = threshold "HEAP_PERCENTAGE" = "90" action = "OVERFLOW_TO_DISK" / >

  < / gfe: replicated-region >

  < gfe:local - region id = "localRegion" cache-ref = "gemfireCache" / >

  
  

  With the above configuration, I can successfully call JSONFormatter.fromJSON (json) and get a reference to a PdxInstance object.  However, when I kinda modify configuration to enable the persistence of drive on one of the regions, the call to JSONFormatter.fromJSON (json) fails.  The change is as follows:

  
  

  < gfe:local - region id = "localRegion" cache-ref = "gemfireCache" persistent = "true" disk-store-ref = "persistOverflowDiskstore"/ >

  Without any additional modification, the following error starts occurring:

  com.gemstone.gemfire.pdx.JSONFormatterException: could not parse JSON document: [Source: java.io.StringReader@5549f0e, line: column 26,: 6]

  at com.gemstone.gemfire.pdx.JSONFormatter.fromJSON(JSONFormatter.java:66)

  ...

  Caused by: com.gemstone.gemfire.pdx.PdxInitializationException: The PDX metadata must be persistent in a limb that has persisted data. See CacheFactory.setPdxPersistent.

  at com.gemstone.gemfire.pdx.internal.PeerTypeRegistration.checkAllowed(PeerTypeRegistration.java:531)

  at com.gemstone.gemfire.pdx.internal.PeerTypeRegistration.verifyConfiguration(PeerTypeRegistration.java:515)

  ...

  Note that it is breaking while I try to get a reference to a PdxInstance, and if the code has not yet arrived at the point where I place a PdxInstance object in a region.

  Thanks for any help in advance.

  Hello

  JSONFormatter PDX uses as is the serialization mechanism from the Gemfire cache. As indicators of error, you must have your persistent PDX meta-data when you use PDX with an area that itself is persistent. Adjust your configuration as follows:

  It will use a default for PDX record store, but you can also use a specific store if you wish.

  When you use PDX, a "PDXType" is created for each class serialized with PDX and this type id is stored with the data in the region. If this region is persistent, then the PDXType, associated with this object must also be kept.

  -Jens

• Configure to integrate Cisco ASA and JOINT

  Hello

  We have Cisco ASA and JOINT, need assistance on the integration of the same thing; Please email me so that I'll share the details of the architecture.

  Thank you best regards &,.

  REDA

  Hi reda,.

  If I correctly your diagram, you do not want to send any traffic from the external switch to the JOINT with a SPAN port and all traffic from your DMZ interfaces with another.

  Is this correct?

  If so, can you tell me why you want to inspect the traffic before it goes through the firewall? As I said in my original answer, we generally advise putting IP addresses after the firewall.

  Not to mention that in your case, I guess that some traffic will be inspected twice so you will need to assign a different virtual sensors to each JOINT internal interfaces to ensure that the same instance does not see the traffic of several times.

  Kind regards

  Nicolas

• SG300 and RVS4000 DHCP problems

  We recently deployed SG300-28 to replace a former 3Com switch.

  The installation program:

  In the SG300 switch router RVS400 and all workstations and server are connected.

  The problem:

  Windows 7 workstations are unable to get IP addresses of the server that is also connected to the switch.

  If, however, plug us into the workstations in the switch 4 ports on the back of the RVS4000 (the router), they get the IPs from the server without problem.

  It works perfectly with the old switch from 3Com for us it was classified in the category small business going.

  A few comments/advice appreciated! Thanks in advance!

  Pavol

  Pavol,

  Please make sure the SG300 switch running latest firmware 1.1.2.0, also new code then please switch factory reset after the upgrade. If you need assistance in upgrading please call Cisco Small Business Support Center @ 1-866-606-1866

  After upgrading please repost how these devices are connected and the configuration of your RVS4000 & SG300 switch series. Using RVS4000 for your DHCP server?

  Also make sure your RVS4000 is running latest firmware as well.

  Jasbryan

• IOS VPN on 7200 12.3.1 and access-list problem

  I'm in IOS 12.3 (1) a 7200 and have configured it for VPN access. I use the Cisco VPN client. Wonder if someone has encountered the following problem, and if there is a fix.

  The external interface has the access-list standard applied that blocks incoming traffic. One of the rules is to block the IPs private, not routable, such as the 10.0.0.0 concern, for example.

  When I set my VPN connection, none of my packets get routed and I noticed that outside access list interface blocks the traffic. When I connect to the router through VPN, the router attributes to the client an IP address from a pool of the VPN as 10.1.1.0/24. But normal outside the access list denies this traffic as it should. But as soon as I have established a VPN connect, it seems that my encrypted VPN traffic must ignore the external interface access list.

  If I change my external access list to allow traffic from source address 10.1.1.0/24 my VPN traffic goes through correctly, but this goes against the application to have an outdoor access list that denies such traffic and have a VPN.

  Anyone else seen this problem or can recommend a software patch or version of IOS which works correctly?

  Thank you

  R

  That's how IOS has always worked, no way around it.

  The reasoning is to do with the internal routing on the router. Basically an encrypted packet inherits from the interface and initially past control of ACL as an encrypted packet. Then expelled the crypto engine and decrypted, so we now have this sitting pouch in the cryptographic engine part of the router. What do we with her now, keeping in mind users may want political route she is also, might want to exercise, qos, etc. etc. For this reason, the package is basically delivered on the external interface and running through everything, once again, this time as a decrypted packet. If the package hits the ACL twice, once encrypted and clear once.

  Your external ACL shall include the non encrypted and encrypted form of the package.

  Now, if you're afraid that people can then simply spoof packets to come from 10.1.1.0 and they will be allowed through your router, bzzzt, wrong. The first thing that the router checks when it receives a packet on an interface with a card encryption applied is that if the package needs to be encrypted, it is from his crypto ACL and its IP pools. If he receives a decrypted packet when it knows that it must have been encrypted, it will drop the package immediately and a flag a syslog something as "received the decrypted packet when it should have been."

  You can check on the old bug on this here:

  http://www.Cisco.com/cgi-bin/support/Bugtool/onebug.pl?BugID=CSCdz54626&submit=search

  and take note of the section of the security implications, you may need to slightly modify your configuration.

• Turn on the mtu on cisco switch and cisco user server

  Hi all

  someone got bad luck turning on the mtu on their cisco switch?  I guess I need to turn it on for all because the command is for all ports on cisco catalyst and my server switch is nearby to my user of switches and a broadband bandwidth 6 G or 6 ports, I need to turn it on for all user ports?

  Thanks for any comments, that you can add.

  I assume you mean Jumbo frame support! You shouldn't have any problems with that. Please take a look at for example http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml for more details and the configuration of the different switches. According to the model, the parameters are for dedicated ports only or the entire switch. In the case of the switch everything you will need to reload (reboot) switch, so be careful.

  André

• Several Airport Apple ID devices disappear shared devices and Software Configuration of the airport

  We have three Airport extreme and two Airport Express devices in two offices in the city.  Some time in the last two days, they all stopped appearing in the sidebar of Finder 'Shared' category (if they had attached disk storage) and they stopped from appearing in the Configuration software of the airport on any of the Mac on these networks. (They always seem to be correct, routing traffic, however).

  For a while, we left a desktop completely alone as a control group and did all our testing and troubleshooting in the other office.

  We-hard reset (to the factory configuration) all devices from the airport to an office. They began to appear again. Then we started to re - configure them again.  At the time wherever we had updated the devices they had disappeared again.

  So, another factory discount based configutations for each device to this facility. Then we added slowly in pieces of their configuration.  When airports have received Apple ID and associated passwords for associating with iCloud/BackToMyMac/WideAreaBonjour (depending on what you want to call it), the airport devices disappeared from the airport Setup.

  If we tried to configure another device from the airport to extend a network of 'invisible' airports, the new airports were "unable to find" one of these networks to expand.

  If we reset all devices without providing them with Apple ID and passwords, they worked mainly as you would expect. The main difference being now do not appear as having been recorded as BackToMyMac/WideAreaBonjour devices.

  One side for people dealing with this note: If your router are invisible, but they are configured to be configured from the EXTENSIVE worldwide network, you can use "File-> configure the other" and specify the address WAN of the missing aircraft and get this screen access as one would generally. From here, remove all the Apple ID associated with these devices, press "Refresh" to save the settings and they seem to reappear magically in the Configuration of the airport software.

  In that State, storage seems to be available, but only for devices in Domain Local (direct connection). Airports without AppleIDs will not appear in the field to iCloud/BackToMyMac/WideAreaBonjour, and it's as expected, given that these IDS is the means for the identification of their field.

  If someone else has noted these behaviors and if so, have an idea about specifically when they first appeared? Is there by any chance someone who knows of any change in registration or the MWAC of multiplication?

  Did you approach the problem exactly as I did in the past, and having encountered problems of the CCMM literally every version of OS X. They were all distinct problems with individual characteristics, and in some cases the solutions exist. Having said that the CCMM has been completely reliable recently - which means running the most recent El Capitan release on all my Macs. The initial versions (i.e. OS X 10.11 to 10.11.3 maybe) didn't work at all. I don't know which version fixed whatever the problem was, I am sure he has not worked for someone else.

  The same real place with Yosemite and previous versions as well. CCMM did not reliable until the exit "point three or four."

  Through these experiments, I believe it should be a pretty fast connection. If the connection between a Mac and all the others does not meet this requirement (whatever that is) all you will be able to determine, it's that the CCMM fails.

  Apple is characteristically silent about the technical aspects of the CCMM, probably because of security concerns. Nobody outside Apple knows how it works. If you're still having problems, I encourage you to contact them. After mentioning predictable you corrective raw materials (the two following links) you will be put in touch with someone who will look to what is false, providing diagnostic assistance and send your information to engineering. If it's something they should fix, you'll know not to the point of an OS X update is published.

  Set up and use Back to My Mac - Apple Support

  Get help using Back to My Mac - Apple Support

  With all the conversations I had with Apple on this topic (which were many, involving a large amount of tests) not once they disclose any causal factors individual, other than to reiterate the need to run the last OS X, versions and the latest versions of firmware for their routers. In your case, that means probably that your Mac update to El Capitan. It is after all the very first recommendation in their document of support above, until you do this you will still not get in step 1.

• two drivers of PXI chassis with Configuration problem

  Hello

  I have two PXI chassis. One is PXI 1033 and works perfectly with the NI PXI-5404, 5105, 6509, 1409, installed 8336. The other is 1036 PXI with the PXI-5404 NI, 8366 installed. When I was trying wreath connect, as master 1033, 1036 as slave, I found several problems.

  1. in the Measurement & Automation Explorer, does not have my good guys in 1033. Instead, there is a sign of the Red Cross in bottom right with 6509, 5105, 5404.

  2. I can't find an another 5404 of the 1036. In fact, I can't find 1036 in MAX.

  Update BIOS. My PXI system is already identified under the name 'NOR PXI - 1033 Embedded MXI Express' and Chassis1 is identified as 'NOR PXI 1033'.

  So I made several tests as below:

  1. unscrew the 5404 1036 slave. MAX can configure 2 1036 chassis. Ok. But when I reconnect 5404 in 1036, same result happened as stated above.

  2 uninstall the driver of 5404, so the 5404 in 1033 does not either now. And then reboot again, same result happens again. Cannot detect the 1033 chassis. Other vouchers in 1036 don't work either.

  Please, any suggestion is highly appreciated.

  Sincerely,

  Bin

  Hi Ben,

  This happens sometimes with MXI-Express:

  Error code 12 with MXI-Express

  http://forums.NI.com/T5/PXI/two-PXI-chassis-connection-with-configuration-problem/m-p/1475876#M9033

  In general, you can read this error 12 means on Device Manager:

  Explanation of error codes generated by Device Manager in Windows XP Professional

  http://support.Microsoft.com/kb/310123

  If it was a problem of bandwidth, PCI or PXI side, you could pull a few cards to see if that alleviates the problem, or that the link from Microsoft over the States, you can disable the driver for other cards.

• I have my windows automatic update. the other day, my windows updated and Ive had problems of e-mail and online video problems. I have vista Home premium OS. any suggestions?

  can receive email, but not able to send after the recent ('important') updates of windows have been installed.
  also can't see videos on facebook because of the mistakes because of these updates.
  I have the my windows update set to automatic and noticed these problems after an update has taken place. I did a system restore and everything worked fine. Needless to say the next day, the same thing. I even went to the windows update to manual setting, and it is always updated by itself. This made 4 consecutive days. now when I go to system restore, I don't even get the opportunity to go beyond 5 days! video errors on facebook tell me that "the video is unavailable" and "video has been deleted or is not visible because of the privacy settings. I also noticed that most installed updates are updates to windows security. and my windows update seems to be popping up constantly telling me ago over updates to install.

  Hi Unhappy72,

  I'm sorry that you are still facing the same problem. I'll be more than happy to help you.

  I have a few questions:

  (a) what version of IE are you using?

  (b) has been going through the steps to reset Internet explorer?

  (c) you have any version of Flash Player on your system?

  You can try to update the version of Flash Player for videos.

  To do this all first you need to uninstall and then go ahead and download the latest version and install it.

  To uninstall the application follow the steps given below:

  1. open programs and features by clicking on the Start button, click Control Panel, clicking programs, and then clicking programs and features.

  2. Select a program, and then click Uninstall. Some programs include the ability to modify or repair the program in addition to uninstall, but many simply offer the option uninstall. To change a program, click change or repair. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  For more information, please visit the below given link:

  Uninstall or change a program

  http://Windows.Microsoft.com/en-us/Windows-Vista/uninstall-or-change-a-program

  You can also check if the connection parameters are set by default.

  Make follow them the steps below:

  1. open Internet Explorer.

  2. press the Alt key on your keyboard for the file menu if it is not already there.

  3. go to tools, click on Internet Options.

  4. click on the Connections tab.

  5. at the bottom of the page, it will be a local network settings tab, click on this.

  6. check if automatic detect settings is enabled in the box, if it isn't what to choose.

  7. close all Internet Explorer Windows and reopen and check if the problem persists.

  This should solve your problem of not being able to send emails.

  You can also try to clean boot your system and then try to play the videos. This will let us know if the background services interferes with the proper functioning of your system.

  To help resolve the error and other messages, you can start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  The steps to perform a clean boot are given below:

  1 log on to the computer using an account with administrator rights

  2. click on start, type msconfig.exe in the start search box and press ENTER to start the System Configuration utility.

  If you are prompted for an administrator password or for confirmation, type your password, or click on continue

  3. on the general tab, click Selective startup, and then clear the check box load startup items. (The check box use the file Boot is not available.)

  4. on the Services tab, click to select the skin all the Microsoft services check box, and then click Disable all

  Note: Following this step lets services Microsoft continue to run. These services include networking, Plug-and-Play, record of events, error reporting, and other services. If you disable these services, you can permanently delete all restore points. Do not do this if you want to use with existing restore points system restore utility

  Once you have disabled all services that you can check if you are able to play the videos. If so, you can try the divide and conquer method to find what service exactly the origin of the problem. For those who follow the below given link:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. click on start, type msconfig.exe in the start search box and press ENTER.

  If you are prompted for an administrator password or for confirmation, type your password, or click on continue.

  2. on the general tab, click the Normal startup option, and then click OK.

  3. When you are prompted to restart the computer, click on restart

  Alternatively, you can try to disable the modules such that some add-ons can be a problem while browsing through the internet.

  To disable the modules follow the below given steps:

  1. click on the Start button, click principally made programs, on Accessories, click System Toolsand then click Internet Explorer (No Add-ons).

  For more information on the modules, please visit the below given link:

  Internet Explorer Add-ons: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/Internet-Explorer-Add-ons-frequently-asked-questions

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• "When try to turn on my computer: Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid

  Original title: configuration of the CRA

  Hi, I got this message then try to turn on my computer:

  "Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid. "Please check the Windows documentation about the configuration option BOW and your reference manuals of the equipment for more information.

  can someone help me?

  Hi sugenghariyono,

  ·         Did you do changes on the computer before the show?

  ·         What is the brand and model of the computer?

  ·         Are you able to boot to the desktop?

  Follow the steps in the article.

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  For reference:

  Advanced Troubleshooting for General startup problems in Windows XP

• Fix KB2518864 & KB2478658 updates will not install and have a problem. How to solve this action?

  Fix updates KB2518864 & KB2478658 will not install and have a problem. How to solve this action? This fix tries to install when arrested computer, but when the computer is turned back on, there is a box which reads:

  Patching HOTIRON Setup has encountered a problem and needs to close. We are sorry for the inconvenience.

  Hi MrGreener,

  1. did you of recent changes on the computer?

  2 are you able to install all other updates on the computer?

  3. do you have security software installed on the computer?

  4. you receive an error message while updates?

  Method 1

  I suggest that you manually download and install updates, check if it installed correctly on the computer.

  Security Update for Microsoft .NET Framework 3.5 Service Pack 1 and .NET Framework 2.0 Service Pack 2 on Windows Server 2003 and Windows XP

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=26323

  Security Update for Microsoft .NET Framework 3.5 Service Pack 1 and .NET Framework 2.0 Service Pack 2 on Windows Server 2003 and Windows XP

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=26427

  See also the articles below to learn more about known issues for both updates and check if it helps.

  MS11-044: Description of the update of security for the .NET Framework 3.5 Service Pack 1 and the .NET Framework 2.0 Service Pack 2 on Windows XP Service Pack 3 and Windows Server 2003 Service Pack 2: Jun

  http://support.Microsoft.com/kb/2518864

  MS11-039: Description of the update of security for the .NET Framework 3.5 Service Pack 1 and the .NET Framework 2.0 Service Pack 2 on Windows XP Service Pack 3 and Windows Server 2003 Service Pack 2: Jun

  http://support.Microsoft.com/kb/2478658

  Method 2

  If the previous step fails then I would suggest that reset you the default Windows Update components and later try to install updates.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Method 3

  If the previous step fails, then it is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• Error message: this action cannot be completed because the other program is busy. Choose ' switch to ' to activate the busy program and correct the problem

  Original title: server busy

  I get a popup server busy with the message: "this action cannot be completed because the other program is busy.  ' Choose ' switch to ' to activate the busy program and correct the problem.  There are two buttons"'Switch To' and 'Retry '.  Neither fixes the problem and I do not understand what they are talking about.

  Hi adarb,

  1. when exactly you get this message?

  2. what applications do you use when you get this message?

  Method 1:

  You can restart the computer and check if it helps.

  Method 2:

  You try to perform a clean boot. A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  http://support.Microsoft.com/kb/310353

  If your problem is resolved after the clean boot, and then follow the steps mentioned in the article above to refine the exact source.

  After you have used the boot is a way to solve your problem, you can follow the steps to configure Windows XP to start normally.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.