Cisco recommended for the GRE VIA IPSEC router.

Similar Questions

• The GRE and IPSec

  We currently have several sites with ISAKMP/IPSec tunnels between routers 2800 and we need some of them migrate to the GRE with IPSec tunnels. Are there problems with endpoint tunnels GRE and IPsec on the same router and interface?

  I didn't know all the problems - apart from the router doing the encryption/decryption & GRE encapsulation/decapsulation, just be respect for traffic through the put.

  I have noted problems with traffic GRE and MTU problems. Cisco recommends a MTU of 1440 at Discretion, I would say that set 1400.

  HTH

• Format recommended for the PDF author metadata

  Hello

  I work as a librarian and I am responsible for the Department of the thesis of my University Library. These are filed and archived as PDF files. Some of them are available online, some are not.

  I was told to systematically fill metadata "Title" and "Author" for each PDF deposited in our electronic despository.

  My question has to do with metadata "author." Is there a structure recommended for her?

  As it is I can think of a lot of different alternatives:

  First name last name

  LastName Firstname

  LastName, Firstname

  etc.

  As a librarian, my instinct was to choose the name, first name format (used in the author/creator DC element, for example), but I realized that whenever I have saved the PDF file and then displays the part of metadata (via the shortcut Alt D), it would show "Lastname, Firstname" rather than the full name (for some unknown reason, adds Adobe Pro "" ""). After some tests, I came to the conclusion that the coma was the source of the problem. So I changed my mind and adopted the format Firstname Lastname , but I'm not sure that this is the best option.

  So if I ask you a few questions, here they are:

  -Which format do you recommend for the metadata of the author (if there is one)?

  -Why a coma generates ""?

  Is there a specific separator character that I use when I need to fill two different names (if a given thesis has been written by two different people)? (this issue also applies to metadata "Key words")

  Thanks for your patience and for your time,

  See you soon,.

  JHM

  There are no rules in itself, but the XMP specification defines DC: creator as a ProperName field, which means it must be written in the way he would say - "John Smith" rather than "Smith, John". Finally, it is until you do with data - if your external search system to priority of family name, do it.

  The fields on the tab of "description" of PDF Properties dialog comes from this Document information block in the standard PDF file, which is independent of the XMP metadata. Although these fields of DI are often people will look on, in a formal catalog system the XMP object has priority (indeed, in the ISO PDF/A standard that you are supposed to ignore completely DI fields).

  Document Information fields are stored in the PDF file as strings rather than the XML entities. Commas would confuse the parser in thinking it was to see a table, so they will trigger Acrobat in order to encapsulate the entries between quotes. He will assume a comma and a single space are part of an individual term, if you want to create a list using the semicolons or several spaces between words. Senicolons conquer spaces:

  • Doe, John; Lord Lucan; Barney, the Purple dinosaur will be kept at the "Doe, John"; Lord Lucan; 'Barney, the Purple dinosaur'
  • Is no one, no one will be kept to the ', that is, not a "; person because the spacing is a term separator.
    

  The important thing to remember is that the entrance of DC: creator XMP is updated whenever you change the author field of DI, but it does NOT follow the same rules. ProperNames XMP are OK with spaces but they don't like commas or semicolons - so the first example above appears in the tree view of XMP as

  1. DOE
  2. John
  3. Lord Lucan
  4. Barney
  5. Dinosaur
  6. the
  7. Purple

  This reinforces the idea of using names as spoken. Lord Lucan has survived his trip to XMP, John Doe became two people. Barney is beyond hope. in many ways.

• Recommendation for the configuration of the disk

  Recommendation for the configuration of the disk:

  A wide range of RAID 5 consisting of 8 x 146 GB drives?

  Two arrayys of RAID 5 with 4 x 146 GB drives in each table one would be used for the data store, and the other would be usd to images of backup to it.  The idea here is that when we do backup via the script GhettoVCB/o would be mainly on the secondary RADIUS and not the main data store.   In my opinion?  I think I have the only RAID 5 Bay with all the readers of 8 x 146 GB for a data store single should surffice.   I don't think the performance problems will be that detrimental.

  Do not hesitate to offer advice on scenarios, thank you

  Engineer accommodation

  ModusLink Open Channel Solutions, Inc.

  As written before, depends on the type of e/s.

  With more than R and W low, RAID5 (on multiple disks) could be very good.

  But don't forget to also use a global hot spare, degraded performance a RAID5 mode could be dramatic.

  And don't forget that your controller has a battery backup.

  André

• Recommendations for the best 3D modeling App / program?

  Does anyone have a recommendation for the best 3D modeling application / program?

  (More for the creative rather than animation games and computer work)

  Thank you

  Hello

  I love Autodesk Inventor, but you need to use BOOTCAMP or VMWare/Parallels to run it because it only works with Windows.

  See you soon,.

  Adam

• IPad disabled with thousands of pictures of children that are not backed up with iTunes or icloud. Recommendations for the recovery of photos please?

  IPad disabled with thousands of pictures of children that are not backed up with iTunes or icloud. Recommendations for the recovery of photos please?

  Sorry, but if your device is disabled and you have no backup, then you won't be able to save the data on the device:

  https://support.Apple.com/en-us/HT204306

  You should back up your device regularly to iCloud or import your photos to an application on your computer. Otherwise, you will be risking losing those photos. If your device has been lost, stolen, or crushed by your car, you'd be in the same situation. Really sorry for your photos.

  Good luck

  GB

• I need a download of software recommended for the Transcriber ICD-PX312 for Windows 7.

  I installed the software that came with the ICD-PX312 on a windows system 7 and it crashes constantly. I need a download location for the software recommended for the valid software for the Windows 7 platform.

  all links will be useful.

  Hi Tim,.

  Welcome to the community of Sony!

  Download and install the latest version of the software of the Organizer from the link below:

  http://eSupport.Sony.com/us/p/SWU-download.pl?MDL=ICDPX312&upd_id=8218&os_group_id=5

  If my post answered your question, please mark it as an "accepted Solution".

  Thank you for your message.

• Parallel logic LSI, LSI logic SAS, parallel Buslogic (not recommended for the guest operating system), vmware paravirtual

  Infrastructure:

  vSphere

  ESX 4

  Reference Dell R710 Server

  I install WIN 2003 x 64 as a virtual server on ESX 4, when I select LSI logic SAS & LSI logic parallel it does not detect the hard drive, do I need driver if so where can I download?

  For parallel bus logic (not recommended for the guest operating system) & Vmware paravirtual, do I have to select this option for my win 2003 R2 x 64 edition?

  Please help on this issue.

  ~ Rashid

  If you really want to use it for installation, you will need to extract the driver from the VMware Tools ISO and add it to a disk image.

  Dave

  VMware communities user moderator

  New book in town - Start Guide quick vSphere -http://www.yellow-bricks.com/2009/08/12/new-book-in-town-vsphere-quick-start-guide/.

  You have a system or a PCI with VMDirectPath?  Submit your specifications to the unofficial VMDirectPath HCL - http://www.vm-help.com/forum/viewforum.php?f=21.

• The GRE over IPSec vpn

  VAC

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a008009438e.shtml#diag

  It's lab that I did today, and offcouse, I am able to understand this laboratory bus are confusion

  1. Why do we use a card encryption on both interfaces (phiycal tunnel interface or interface)

  
  

  2. when I remove the interface tunnel encryption card I have this message

  ( R2691 #* 01:12:54.243 Mar 1: ISAKMP: (1002): purge node 2144544879 )

  Please tell me what is the meaning of this message

  3. but I do not see vpn works great. It comes to cryto his and crypto isakmp his

  R2691 #sh crypto ipsec his

  Interface: Serial0/0

  Crypto map tag: vpn, local addr 30.1.1.21

  protégé of the vrf: (none)

  local ident (addr, mask, prot, port): (30.1.1.21/255.255.255.255/47/0)

  Remote ident (addr, mask, prot, port): (10.1.1.1/255.255.255.255/47/0)

  10.1.1.1 current_peer port 500

  LICENCE, flags is {origin_is_acl},

  #pkts program: 65, #pkts encrypt: 65, #pkts digest: 65

  #pkts decaps: 66, #pkts decrypt: 66, #pkts check: 66

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, #pkts compr. has failed: 0

  #pkts not unpacked: 0, #pkts decompress failed: 0

  Errors in #send 2, #recv 0 errors

  local crypto endpt. : 30.1.1.21, remote Start crypto. : 10.1.1.1

  Path mtu 1500, mtu 1500 ip, ip mtu IDB Serial0/0

  current outbound SPI: 0xDBF65B0E (3690355470)

  SAS of the esp on arrival:

  SPI: 0x44FF512B (1157583147)

  transform: esp-3des esp-md5-hmac.

  running parameters = {Tunnel}

  Conn ID: 5, flow_id: SW:5, crypto card: vpn

  calendar of his: service life remaining (k/s) key: (4598427/3368)

  Size IV: 8 bytes

  support for replay detection: Y

  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:

  SPI: 0xDBF65B0E (3690355470)

  transform: esp-3des esp-md5-hmac.

  running parameters = {Tunnel}

  Conn ID: 6, flow_id: SW:6, crypto card: vpn

  calendar of his: service life remaining (k/s) key: (4598427/3368)

  Size IV: 8 bytes

  support for replay detection: Y

  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  R2691 #sh crypto isakmp his

  IPv4 Crypto ISAKMP Security Association

  status of DST CBC State conn-id slot

  30.1.1.21 10.1.1.1 QM_IDLE 1002 ASSETS 0

  ISAKMP Crypto IPv6 security association.

  How can 2: I know it using GRE over IPsec.

  I also join my topology on which I made lab

  Also beyond what I remember, in the old codes he was required to have a card encryption on tunnel and physical interface, but now is not.

  Since we use GRE over IPSEC, so for the verification of the tunnel I'll do the following steps:

  (1.) to check if the tunnel interface is in place. "show ip int br".

  2.) check if the statistics of tunnel are increasing and packages are browsing through it. 'show interface '.

  3.) check if crypto ACL includes only interesting traffic listed as GRE counterparts.

  (4.) If Yes, check the IPSEC Security Association statistics. "See the crypto ipsec his."

  If all of them are correct statistical evidence with respective counters increase traffic is passing by GRE and then by wrapping in IPSEC.

  I hope this helps.

  Kind regards

  Anuj

• Recommended for Y2 tab 13 wifi router?

  For the moment, I have an old class 'g' wifi router that is capable of approximately 50 Mbps (if I correctly interpreted the specifications). I see that new class routers 'n', as well as tablets of Yoga, are capable of about 600 Mbps - that seems a great improvement. Could anyone recommend a particular model that works well and stable with tablets of Yoga?

  I tried Googling Amazon these and reading reviews, but I'm not much smarter afterwards... Some models I've looked at (I know these support even better than "n" speeds, but this seems an investment of better evidence and more pure future router "n"):

  • TP Link Archer C7 - cheaper but less reliable and slower than the competition
  • ASUS RT-AC68 - much praise, but also a lot of (bad) 1 and 2 star reviews
  • ASUS RT-AC87 - once again a lot of praise, but also many people with questions
  • NETGEAR R7000 - mixed with new comments and support which would have been particularly bad manufacturer

  I'd be happy with just a reasonable speed improvement (for example, currently I can not stream movies in high definition and even just browsing files on the other machine on the local network is slow noticably) and I do not connect several devices simultaneously (generally 1 to 3).

  Hi DigiMagic,

  The routers at the end of the day depends on the feature you're looking for. Example of some routers have invited mode, children's fashion, supports USB / NAS, etc.

  That's why at the end of the day, it would depend on what you will be using the router for. As for me, I have 2 access point at home because of my low WLAN router and I intend to get one that is dual band with AC to ensure future proofing...

  Hope that helps = D

• Recommended for the load of Apple pencil

  I realize that I can plug my Apple pencil in my iPad to load. In addition, provided with the Apple pencil is an adapter of lightning... I used this map of lightning with my Apple 5 watt power adapter and the light provided with my iPhone cable to recharge my pencil to Apple as well. I have not, however, used the lightning with my iPad Pro 12 watt adapter adaptor and cable lightning because I guess it will be dangerous for the pencil of Apple... Am I wrong? In an effort to try to extend the life of my pencil to Apple and not to damage through loading wrong practices, I wonder what Apple recommended to load that my Apple pencil is?

  Should be charge with the power adapter supplied with your iPad Pro.

• Recommendations for the power supply of the inverter of supply for an iMac 27 "SSD (1 TB) 2015?

  I heard that SSDS are vulnerable to data loss / corruption in irregular situation (surges, outages, etc.) and that a UPS is strongly recommended. No one knows what might work best for an iMac 27 "2015 (late) with 1 TB SSD? Amazon best sellers are quite disparate. No. 1 is perhaps not strong enough. N ° 4 seems not to have the OS X compatible software. Being new to this kind of material I don't know what to look for and what would be better for my machine.  It seems consume 240 W max.

  In this regard: I read that store a SSD in hot weather can ruin the drive (or some dr. I considered turning off my computer when I'm away for the summer (in a non air-conditioned office which heat sometimes). I better let him run (sleeping)?

  Thanks in advance.

  A UPS is recommended as soon as you have an irregular situation. It does not matter if you have a hard drive, SSD, or something else.

  240W is the max for the whole iMac.

  Not sure where you hear your horror stories about SSD.

• Port forwarding for the suddenly closed Linksys router

  I have a 54G wireless router... correctly port forwarded a request of a CPU (server)... but after no connection made by the user on the server... it suddenly close the application... so what I did is to reboot the router in order to refresh the connection...

  Are there other ways to fix this sudden closure of ports?  so that I would more restarts on my router

  I appreciate a lot of help...

  As directed by your statement the port that you have passed on the closed router without any connection to the server is unusual. Please make sure that you have configured an IP address static (outside the range of the router DHCP) on your server and put the same IP address for the specific port port forwarding tab.

  In addition, reduce the MTU size on the router to 1400. See the link below on how to make the changes in the MTU size.

  http://www6.nohold.NET/Cisco2/UKP.aspx?VW=1&docid=c018b947b8774e54bd57fad02e3efddd_17331.XML&PID=80&...

• Recommendations for the resolution of the screen on the W510

  Hi people,

  Recommendations on the resolution of the screen on the W510 - HD or HD +?

  And why?

  TIA,

  SD

  It really depends on your use.  I went with the HD + (1600 x 900), because the graphics card is powerful enough run games of high quality on this resolution and it provides decent realestate to make programming and another office on productivity.  I tried a HD (1280 x 800) screen at work and it is very small and useless for real work, but if you are hard to see or don't use it to calculate the light, he would serve well.  The FHD (1900 x 1080) display provides a lot of realestate, if you can read the tiny text and do a lot of business development type and graphic design works, more multitouch features that can be intreguing there, but I think the screen is a little too big to play video games.  That's my thought.

• Can not connect to the internet via my router

  I recently changed my dsl cable and Internet service provider. Everything worked fine when I had dsl (no problem connecting by router) but now I can only connect to the internet when the cable modem is connected directly to one of my PCs. I tried to reset the router by default and computers can see each other on the lan, but after trying to reconfigure the router with the modem cable connected it does not detect not the new address ip & dns info even if the adapter is configured to receive the ip address and dns automatically (in windows and the settings of the router.)

  Is there something else in my network installation of Windows 7 that needs to reconfigure?

  Hi Viking_Dan,

  It is really difficult to troubleshoot network connections because there are so many factors that might cause a problem. I'll do my best, however.

  Make sure that you connected the modem cable to the router using the Ethernet port on the router (Wide Area Network) "WAN". Then try to ping the router from an elevated command prompt window. The default IP address is usually something like 192.168.1.1, or similar. Check with your router's configuration. The ping command is:

  Ping xxx.xxx.xxx.xxx

  (where the x's represent the IP address)

  You will receive all 4 packets back with 0% loss. If you do not have, so I'm puzzled. If you receive all 4 packages without losses and still can't connect to the internet, then check if the radio for the router matches the capacity of your PC. Your router may have a frequency of 2.4 GHz only, only 5 GHz, or a mixture. Your PC can support one of those, or both. Check to see if they match.

  If it still does not work, try to set a static IP address for each of your PCs, with the IP address of the router as the default gateway. For the DNS server, I suggest that you use the DNS from Google free, fast and secure server. The IP address is 8.8.8.8

  Let me know what happens