Port forwarding for the suddenly closed Linksys router

Similar Questions

• Need help with the port forwarding for a XBox remote Streaming

  I have a router R6200v2 and need help with port forwarding.

  I came across this set of instructions for setting up stream port forwarding XBox remotely from anywhere

  http://kinkeadtech.com/2015/07/how-to-stream-Xbox-one-to-Windows-10-from-anywhere-with-Internet/

  I have no idea when it comes to such things and I want to make sure I do it correctly without messing up my existing home network.

  Port Forwarding and triggering Port pages setup look very different from what the guy uses. Can someone walk me through what I do to set up please?

  Hi @varxtis,

  You must enter them in the field for a start external Port and external completion Port. You will need to send individually except for the range of 49000-65000. The steps are as follows.

  1. create a Service name (it could be something else that you cannot use the same service name twice. Ex. XBOX1, XBOX2 and so forth.)

  2. Select the type of service (TCP, UDP or both)

  3 entry 5050 times a start external Port and external endpoints.

  4. Select the IP address of your XBOX.

  5. Select apply.

  6 do the same for other port numbers. To the beach, use 49000 for the external departure Port and for the external completion Port 65000.

  Kind regards

  Dexter

  The community team

• Port forwarding on the WAN IP unique vShield

  Hello, is it possible to do port forwarding "of the router outside the IP address' for the vShield Edge VM, or am I assume I have to add a second outside of the IP to perform port forwarding from a foreign port to worms a server in-house. Essentially, here's my problem:

  
  I want the vShield Edge IP, if I type the IP address of it on port 80, I want that it will to an internal server on this port. I am only able to do that if I add a SECOND outside address on the firewall. It is a problem because I don't want to burn two addresses by customer just to PAT. Any thoughts? It is an important situation. Thank you

  At the point where you need two survey periods to do this. Basically, the first IP address is dedicated to the NAT traffic.

  VCloud many users have requested to change this behavior, I hope that we will be able to use a unique IP address in the future. Even as a service provider with several available IPs, they are valuable, and it is a waste.

• Error: Could not find the WSDL port defined for the Service

  Hello

  I am facing error below when calling the partner WSDL:

  Oracle.Fabric.Common.FabricInvocationException: Cannot find the WSDL port defined for the service.

  Can someone guide me what could be the exact problem?

  * I can't ping this host.

  Thank you

  Richa

  Puneet salvation,

  I am able to access from the WSDL browser and value of the location in composite.xml is correct.

  Kind regards.

• Try to open the port or do port forwarding for update of the game client (improve the download speed)

  I recently participated in the beta FFXIV and im not to attempt to update the client. It happened for a day now and im only at 78%. I looked on the forums on the site and he told me I should do port forwarding and ill be able to download the updated much more quickly. So my question is how do I port forwarding on a router NetGear on Windows Vista.

  Hello

  Ports must be sent to the IP of the specific computer.

  A specific port can only be transferred to a computer.

  He must be facing forward in the router and also via the firewall software.

  Instructions depends on the specific router you have (the manual force) be useful and the specific firewall software that you use (using the software may contain instructions).

  This site is the champion of port forwarding, http://portforward.com/

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• port forwarding for file sharing on the internet.

  I am trying to determine what port numbers, I need to transfer to my router (in virtual server) to be able to share my NAS files over the internet with my friends? I want to use file sharing, have implemented a DDNS on the NAS with a client account to my dynamic IP address, but cannot get the numbers correct port developed to be able to configure port forwarding. Can anyone help?

  Hello

  Open sharing Ports that are used on a local area network on the Internet is a Big safety hazard.

  There are secure applications that are built for this purpose, they use their own ports and generally are safe (as on the VPN or SSH).

  A free quick simple way is shared through secure ftp server. http://FileZilla-project.org/

  An elegant way door application like this, http://download.cnet.com/WebDrive/3000-2160_4-10017919.html

  In general, http://www.practicallynetworked.com/howto/fileshare/fileshare_intro.htm

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• How can I enable port forwarding in the router of the time capsule

  Does anyone know how to enable port forwarding in router Time Capsule Airport please?

  Port Mapping on the time Capsule airport cannot be enabled unless you have the right type of modem on your network.

  Thus, we need the number of brand and model of the device you're calling your "modem" before we can move forward. Please post back this information.  We do not need a series number... only the name of the manufacturer and model number of the modem.

• Why isn't my port forwarding of the opening port

  I have the latest version of the 3 terabyte time capsule. I'm trying to forward a port so I can access my security cameras and it does not open.  My camera 100 port needs to be open and it will report as not open on any port test sites. Any ideas as to why, I use a static ip address of the server for the security system.

  Testing websites are useless... test by plugging actually to the camera from a device attached to a captive phone or a friend...

  Port forwarding works only if you have the public IP address on the Wan of the TC... and it's the only router in the network... is this the case?

• Port forwarding for Cisco RV042G TSE

  Hi, I have just configured a Cisco small Business routers on my network RV042G. My problem is that I would like to allow TSE through the WAN1 and I am not able to do. I place this information in the menu:-Setup / Forwarding TSE[TCP/3389~3389]->192.168.1.15 - firewall / access rules: allow TSE [3389] WAN1 192.168.1.15 ~ 192.168.1.11 192.168.1.15 ~ 192.168.1.15 still configuring it please? Thanks for your help.

  Thanks for the reply.

  There is nothing else that can be done on the router RV042G. all the configuration is in place.

  The only other way to make this work is to see if you can do the port forwarding on your modem and then forward all ports to the WAN address of the RV042G, or if the modem allows to create a DMZ, then you can connect the router to the DMZ port, but that's all.

  Please let us know.

• Port forwarding for EYEMAX DVR on WIn Server 2012

  We use the router as a network controller on our local network. Now, we have replaced router with the server (win 2012 r2 essentials). We have an EYEMAX DVR client software to connect to a remote ip address in the web.

  Previously, I had the configuration of port forwarding router and EYEMAX was working. When we replaced the router with a server that I can no longer connect. I guess that there is a similar setting to perform on a server, but I can't figure out what to do. This certainly isn't a Firewall (when I turn it off EYEMAX still do not work).

  There is a statement (http://site.camtechsurveillance.com/downloads/remoteacc.pdf) how to configure a router to work, but I do not know how to apply similar changes on the server.

  TL; DR.

  How to do the same on the server like here http://site.camtechsurveillance.com/downloads/remoteacc.pdf

  Try asking in the Windows Server forum:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Port forwarding on the SA520W - Help!

  Hey guys! I need help :)

  We have a SA520W and I can not port forwarding to work.

  I want to say I'm not a computer scientist, even though I know a bit :)

  I have a server running on our network that hosts our inventory software.
  Works completely very well locally. I can hit using the name of the computer. Server
  Firewall is not a problem.

  I need that people in our warehouse (building/separate network) to
  access to this server.

  How would I set up so go directly to port 12345 (for example)
  the local IP address of my server?

  I hope someone can help :)

  Thank you!

  Hello

  IM typing this on mobile, so my editing options are limited, but here's what you need to do:

  1. download the following file:

  http://www.Cisco.com/c/dam/en/us/TD/docs/security/multi_function_securit...

  2. create a new personalized Service for the port that you need. Watch the guide you just download page 104. Repeat for all required ports.

  3. then set up the rule for inbound traffic. See page 110 on the guide for this information. Make sure you select WAN by virtue 'Of Interface' and LAN "interface", then select the personalized service, you created and pointed to the ip address of your internal server.

  I hope this has been helpful

• Cisco recommended for the GRE VIA IPSEC router.

  Hello world

  I intend to connect our two remote locations via IPSEC tunnel, looking for the cheapest option available for the router options.

  Do you have any good recommendations?

  Have a nice weekend!!

  Very appreciated

  Hello

  There is 1 that I love so much, it's 892fsp of Cisco.

  It has 8-port switch, you can make l2tp vpn, free will, love, ips, zbf...

  I hope this helps.

  Thank you

  PS: Please do not forget to rate and score as correct answer if this answered your question

• RV042G Port forwarding of the public port of IP internal with another port_number

  Is it possible to create a service that will forward the 9010 public port to an internal IP address with port 23?

  First of all, I don't like to open public Telnet port on the inside so I would use a different public port and secondly my ISP does not allow for some public ports under the port 80

  Thanks for your help

  Order the transfer of UPnP under the configuration table > UPnP tab on the left. Note that UPnP doesn't have to be enabled for the redirection of the function rule.

• change port number for the mobile server after installation

  Jin
  I use windows 2003 server release 2, Server Oracle 11 g R2 and oracle database lite 10g R3. I installed successfully the mobile server with port 80, but when I start the mobile server I get an error message indicating that port 80 is already in use. Now, I need to change the port number of the mobile server. can someone tell me the solution.

  If the Oracle Lite installation type is INDEPENDENT, then to change the port number of Olite in any other available free port number, you must edit the file by default-web - site.xml or site.xml - web-http file present in $OLITE_HOME/mobile_oc4j/j2ee/mobileserver/config directory.

  You can at any time change the port in the file http web - site.xml and bounce services, the new port will take effect.

• Port forwarding for Xbox

  I have a UTM9S Prosecure home and it does not block the Xbox 360 online.

  Xbox is recommended to open the following ports:
  Port 88 (UDP)
  Port 3074 (UDP and TCP)
  Port 53 (UDP and TCP)
  Port 80 (TCP)

  So I went to the network security-> Services and also Services network-> release of Port Security and added above (TCP and UDP) ports.

  I also enabled UPnP they recommend.

  No luck.

  It was before working with a small router Linksys, so I know it can work if I have the right config, but do not know what I am doing wrong.

  Any suggestions?

  I use a UTM25S on firmware version 3.6.0-32. uPnP does not seem to work for XBox Live. I used the installation trigger port in the post of Shanlord and now it works fine.