Cisco unity conn cluster integration with cucm cluster best practices

Similar Questions

• NTFS file cluster best practice deployment of Windows server on vSphere 5.1?

  What are best practices, VMware or Microsoft that I need to know to make sure the server that I created 2 x Windows Server 2008 SP2 Enterprise MSCS of NTFS file (active / passive Cluster) can operate reliably to be accessed by more than 1,000 people?

  The underlying data disk is RDM because I need to replicate the LUNS in the DR site using the tool table of SANCopy.

  • SCSI controller LSI Logic SAS in Paravirtual changed

  Not really an option... This is not supported by VMware in an MSCS configuration...

  / Rubeck

• Work with several sequences-best practices

  Hello.

  I ve just started using Adobe Premiere CS6. My goal is to create a long movie, which is based on 30 hours of footage in raw gopro recorded on a recent trip of 2 hours.

  Now my question is, what is the best practice for working with many sequences/clips?

  You have a single file of heavy project, with all the clips?

  Or make you small chapters that contains number of sequences x/x minutes long and ultimately combine all these?

  Or how would you do it the best way, so its easier to work with?

  Thanks a lot for your help.

  Kind regards

  Lars

  I make a primary sequence in your project and then modify the individual scenes in the form of separate sequences, and then nest them in the primary sequence.

  That way, you would have a single file of project heavy with all the media files (raw video, music, etc.).

  I find it easier to work with. With the help of several project files would get too complex and fragmented throughout the of your computer.

  I work with a lot of video GoPro, so I wonder what your Setup looks like. What device you have, and how your computer/Premiere Pro is configured?

• vCenter Server with vSphere Essentials best practices for small business

  I hesitated to post this thread for fear of redundancy, but I wasn't able to find an answer in previous discussions.

  I read the installation documentation for vSphere Essentials vCenter Server installation.

  
  Is it a good idea to install vCenter on my ESXi host as a virtual machine?  I don't understand how the server can be installed as a virtual machine if she must always be on.  What happens when I do the updates of the hypervisor, ESXi (4.0 to 4.1)?  This would not cause the vCenter Server to disconnect?

  Because I have Essentials, I don't have a HA and cannot migrate the server vCenter Server to another host as shown in the installation documentation.

  Thank you

  It should not be a problem - if you manually perform the update using either the esxupdate or vcenter command vihostupdate does not at all in the game - if you use VUM he actually intitiates the vihostupdate order - when restarting the host to be reconnecting to vcenter once it is running.

• Connection of the UNIT with CUCM integration

  Hello

  Can someone please advice me on the underside, I CUCM (PUB + 1 SUB) cluster and node stand-alone 1 CUC.

  need to know the best Cisco recommended configuration

  1.0 order of AXL servers (what should we put 0 - PUB or SUB)

  2.0 tftp and order serever CUCM under port, (PUB, order SUB) group settings

  Please advice

  Thank you

  Purna

  Axl Server always be PUB and SUB.
  Pub - 0
  Sub - 1

  TFTP server must first be Sub and PUB.

  Sub - 0
  Pub - 1

  This is the best way and the recommended method to configure / integration with CUCM with connecting the unit

  Sent by Cisco Support technique iPhone App

• Telepresence EX60 with CUCM 8.5 - How to integrate?

  Good morning people,

  I'm building a lab with 8.5 CUCM and presence Server 8.5

  I'll install the Cisco TelePresence EX60, and I wonder how I do integration with CUCM.

  Need to install the additional server? You simply add a SIP device in CUCM?

  Can someone help me?

  Thank you

  Bruno

  Hello.

  You must have CUCM 8.6 in order to utlize the full potential of the CUCM / integration EX60. You save the unit directly to the CUCM.

  I recommend you take a look at this guide, after that you did with your laboratory update.

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC5/administration_guide/cts_endpoint_administration_ucm86_quick_start_guide_tc50.PDF

  I have attached a screenshot showing how it should look like the description of the device.

  Thank you

  Marius

• Cisco Unity full hard

  Hello

  Running Cisco Unity 4.x

  with exchange 2000 on the same box.

  I have two left that everything is installed in the c:\ drive.

  now c:\ drive becomes full.

  I have drive d:\ with 10 GB of free space.

  How can I use this drive d:\.

  Concerning

  M

  Well, 4.x is not real specific - there are 4.0 (1) by 4.0 (4) - many differences between these versions.

  That said, there are a few places to start here. The first is the maintenance of unity here guide:

  http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/products_maintenance_guide_book09186a0080228417.html

  You can move the directories of newspapers to the D drive (in the guide above)-also known as manage the sizes of mailbox for users as well as turning on a circular logging if you do the regular backups of the Exchange database (this can be what is chewing your space).

  If Exchange is installed on C (I assume you are because you say 'all' is on C), you can then follow this technical trick to move logs store and transaction of the messages to another drive:

  http://www.Cisco.com/en/us/partner/products/SW/voicesw/ps2237/products_tech_note09186a00800c6f5f.shtml

  who will save a lot of space on C if logging stuff above is not sufficient.

  Finally, you can move the SQL transaction logs and files on the D drive - you will find details on this in the installation guide

  http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/products_installation_guide_chapter09186a008022b8af.html#wp1664607

  My guess, however, will be that if you pass by the maintenance of the unit guide and check your situation of journaling Exchange, which will probably be enough to free up disk space on your system - if you do not circular logging and that you don't make regular backups of Exchange using BackupExec or something in this direction, then in Exchange transaction logs files will become big enough and chew your space. Whatever it is, the procedures here, should you get from A to B freeing space on C.

• ACS integration with Microsoft Active Directory Services

  Hi all

  I was responsible for developing the integration of GBA with MS AD. What I want to know is below assuming I have a software ACS or ACS device and the authentication protocol's RADIUS

  -What is the criterion of the announcement to integrate with ACS to device software

  -Should that AD hosted on the domain controller or not?

  -Otherwise, on what (DC, tree, forest, branch, flower, Fruit) the announcement must be hosted on?

  -What should I do to authenticate users logging into Cisco ACS Security Manager integrated with AD?

  -Are there other dependencies that I'll have to speak categorically in my description?

  Thank you

  Rishi

  First of all, I love the flower fruit one keep it up.

  If ACS is for windows, it can be installed on the domain controller or member server. For detailed information about installation tasks post must have full integration, please see the following link that contains fancy things you are looking for:

  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/installation/guide/Windows/postin.html#wp1041202

  If ACS is soultion engine then you need piece of software called remote agent to be installed either on the domain controller or member server, also check the following link for more details on how to integrate it with AD:

  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/4.2/installation/guide/remote_agent/Rawi.html

  I hope this was informative for you.

  -----------------------------------------------------------------------------

  Please ensure good answers to rate

• 320 TS Cisco with CUCM integration

  Dear experts,

  Is there a way we can integrate the TS with CUCM 320 without any conductor.

  Means of SIP trunk or as conference bridge.

  BR

  Hi Muhammad

  Telepresence on 310/320 Media Server and Cisco TelePresence Server on a Virtual Machine do not support managed locally; mode on these platforms, the telepresence server must be managed by a system as a conductor of Cisco TelePresence

  Conductor for the unique conference bridge is free.

  BR Oleksandr

• Unity connection 8.6 Migration to 11 with CUCM 8.0

  Due to the right I'm going to intend a Migration of 8.6 connection unit to 11.0 of connection of the unit before I can improve CUCM. I am sure that the answer is Yes, but would there be problems running 11.0 of connection of the unit with CUCM 8.0.

  Nothing fancy on the face of connection of the unit, no unified messaging ect.

  New UC 11.0 should just registered the EPSC ports?

  Thank you

  Dan

  Looks like you need at least version 8.5 for the SCCP and SIP integration CUCM to be supported. Check the compatibility of connection of the unit guide below.

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/connection/compatibil...

  Combinations for Cisco and unity connection Unified Communications Manager of the supported Version

  Table 22 Version combinations of supported for the connection of the unit and Cisco Unified Communications Manager

  Cisco Unity Connection	Cisco Unified Communications Manager
  8.5 and later	11.5 (1), 11.0 (1), 10.5 (2), 10.5 (1), 10.0 (1) 9.1 2, 9.1 (1), 9.0 (1), 8.6 (2), 8.6 (1), 8.5 (1)

  SIP: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/compatibil...

  -Terry

  Please note all useful posts

• Cisco C40 unsubscribe automatically with CUCM 8.6.2

  Hello

  I have Cisco C40 connected to CUCM 8.6.2.

  First, he is registered with CUCM and I was able to call on another phone C40.

  Then, C40 automatically BSW of CUCM and isn't recording with CUCM now.

  I added C40 via device-> phone-> Add new-> then selected Teleprecense C40

  C40 SW version is: 5.1.5.297625

  I joined C40 and CUCM screenshot. It shows not recorded, which proves C40 registerd at least once.

  I could make and receive calls with the C40 for a few minutes. Subsequently recorded automatically and now

  error message is status: failed

  Suggest pls.

  Rgds

  Rajesh

  Hi Renon,

  Please below changes made in the SIP settings:

  change SIP profile 1 Type at Cisco, since it is native enrolled and default transport for TCP

  * c xConfiguration SIP URI 1 profile: "[email protected] / * / "

  "

  * c xConfiguration SIP profile 1 DisplayName:

  * c xConfiguration SIP DefaultTransport 1 profile: TCP

  * c xConfiguration SIP profile 1 TlsVerify: Off

  * c xConfiguration SIP profile Type 1: Cisco

  * c xConfiguration SIP profile 1 outgoing: Off

  * c xConfiguration SIP profile 1 Proxy Discovery 1: manual

  * c xConfiguration SIP Proxy 1 address of profile 1: "172.31.131.10."

  * c xConfiguration SIP profile 1 Proxy Discovery 2: manual

  * c xConfiguration SIP Proxy 2 address of profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 3: manual

  * c xConfiguration SIP Proxy 3 address profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 4: manual

  * c xConfiguration SIP Proxy 4 address of profile 1:

  * c xConfiguration SIP profile 1 1 LoginName authentication:

  * c xConfiguration SIP profile 1 1 password:

• Cisco Unity Express Configuration 8.6

  We have a Router (3945) CME with CUE 8.6 8.6 (ISM-SRE-300-K9 Module). I have a few concerns about the installation and configuration of CUE.

  1. Cisco ships CUE 8.6 Application preinstalled on ISM-SRE-300-K9 Module?
  2. What is the initial state of CUE in ISM-SRE-300-K9 Module when he left?
  3. To restore CUE setting factory and download/install CUE from scratch?
  4. OR can I directly give the IP interface addresses and go directly to the CUE - GUI?
  5. As I ordered three languages (Arab Saudi, British and English North American) these language packs are available with in the Module when it was shipped? or do I have to download and install?

  ISM-SRE-300-K9	Module (ISM) internal services with Services ready engine
  CON-SAU-ISRE300	SW UPGR + SUPP APP internal Services Module (ISM) with SRE
  SCUE-ISM-8, 6 - K9	Cisco Unity Express version 8.6
  CUE-LANG-ARA	Cisco Unity Express - Saudi Arabic
  CUE-LANG-EN	Cisco Unity Express - British English
  CUE-LANG-ENU	Cisco Unity Express - North American English
  FL-CUE-MBX-5	Unity Express license - 5 mailboxes - CUCM and CUCME
  FL-CUE-IVR-2	Unity License Express - Session 2 IVR
  FL-CUE-PORT-2	Unity License Express - 2 ports
  FL-CUE-NR-PORT-2	Unity Express license 2 - no hostable re - Port

  I have recently installed one of these modules and my experience has been that unit has not come with any software installed.  I had to download and install the software/language packs of cisco.com.

• Voicemail configuration base with CUCM and connections of the unit

  Hello again,

  I'm still very new to CUCM.  I am configuring a CUCMB 6.01 test deployment.  He has connections in the integrated unit.  I have 2 DNs assigned to users and Cisco IP phones.  I use MGCP (Cisco 3745 with 2FXO as gateway).  Now, I'm trying to extensions of voicemail installation for the users.  I read a lot of documentation on CUCM and unity, but I know that Unity Express is not what I need, and that you have not found information on the basics of implementing voicemail for users of CUCM.

  Users are DN 1001 and 1002 respectively.  They are part of a list of hunting (broadcast) so that the arrival of incoming calls, both phones will ring simultaneously.  Not sure if this has any bearing or not.  I would like to be able to put in place so that each DN rings on the IP phone say 6 times, then go to a Unity voicemail box configuration for that user.  I have already imported users 2 in the unit.  I ran the voice messaging port configuration wizard.  Everything looks as if it runs correctly, but I'm stuck really share say CUCM to route the call to the mailbox of the unit.  Probably the simplest part.  Ideas or help on this would be much appreciated.  Thank you in advance.

  Impetuous salvation,

  CUCM works this way

  So the fact that 1001 and 1002 receive calls via a group has a significant impact on this config.

  You must keep in mind that a call that is routed through the fighter pilot will always ignore the CFWD settings on phones of hunting member of the group. The normal way to control it then is through disconnection of the Group Hunt members phones combined with the front fighter pilot level settings.

  The following section describes how the parameters to call it forward on the phones of individual members Hunt are ignored when presented a call via the hunting feature. Here's a clip;

  Hunting and call forwarding

  The concept of hunting differs from call forwarding. Hunting allows Cisco Unified Communications Manager to extend a call to one or more lists of numbers, where each such list can specify an order of hunting which is selected from a fixed set of algorithms. When a call extends over a part of hunting of these lists and the party does not answer or is busy, hunting resumes from the next part of hunting. (The next party of hunting varies according to the current hunting algorithm). Hunting has so ignore settings call forward No Answer (CFNA), call forward busy (CFB) or call before all (CFA) for the party to attempt (group member line phones).

  Cisco Unified Communications Manager offers the possibility to redirect a call when hunting fails (that is, when the hunt ends without a part of hunting to the respondent, due either to exhaust the list of numbers of hunting is to expire). If used, this final redirection includes an automatic call forwarding action. Therefore, the fighter pilot Configuration window includes call forwarding configuration concepts which are similar to those found on the directory number Configuration window.

  Example of a call hunt

  Although hunting is different from the transfer, Hunt often develops as a call that gets forwarded to a certain number of fighter-pilot. The protective cover of appeal extends from hunting to allow the final drive after two exhausts of hunting or expires.

  A typical call calling hunting can include the following phases:

  The appeal of hunting through groupings of posts set up according to the algorithms implemented for each group. Hunting is successful (if it meets a hunting party), exhausts (if all parts of hunting are tempted, but no response), or expires (if the deadline set by the Maximum hunting timer runs out before that all parties are tempted, and none of the parties who have tried to answer).

  For the purpose of this example, we assume that hunting does not succeed.

  If a form any of the final drive is configured, the call forward for a next destination; otherwise, the call is released.

  Maximum hunting timer

  The Maximum Hunt Timer field on fighter pilot Configuration window allows the administrator to enter a value (in seconds) to limit the hunting through a list of hunting season. After gaps in the time specified, if hunting was not successful, the call is transferred to a voicemail system, a specific compound number, or some personal treatment (if configured) or the call is released.

  The good doc.

  http://www.Cisco.com/en/us/docs/voice_ip_comm/CUCM/Admin/6_0_1/ccmsys/a03rp.html#wp1078922

  If the call goes unanswered or all Member phones are disconnected, then an attacker needs to be applied at the level of the "fighter pilot".

  Hunt the settings forward

  Before hunting without an answer - when did not answered the call which is distributed through the list of hunting at a specific time, this field specifies how to transfer the call.

  Destination this parameter contains the number of the directory to which calls are forwarded.

  Before busy hunt - when the call which is distributed through the list of hunting is busy at a precise moment, this field specifies how to transfer the call.

  Destination this parameter contains the number of the directory to which calls are forwarded.

  Maximum Timer Hunt - enter a value (in seconds) that specifies the maximum duration for hunting. (Used in conjunction with Forward busy hunting)

  In your case, it is best to configure the DN of a fighter pilot in the extension of alternatives under the 1001 and 1002

  mailbox.

  I hope this helps!

  Rob

• SX 20 with CUCM 8.6.1

  Hello

  I need to record 20 peripheral SX with CUCM 8.6.1, but SX 20 is not available in the list of devices!

  How can I register it?

  Regds

  $

  Hello

  CDP file will be used for the endpoint SX20 push updates of software and the package devce for the CUCM, where it must be installed separately.

  as mentioned in the document provided by Vivek:

  Installation instructions

  Note: Cisco recommends that you apply this device for a package

  maintenance window.

  Note: Packages of devices are installed on the active partition and cannot be

  uninstalled;

  Cisco recommends that you take a backup DRS prior to installation.

  For more information on how to do a proper backup, see the Recovery Guide disaster for each version of Cisco Unified Communications Manager.

  Procedure

  Note: Apply this package of device to all of your Cisco Unified Communications

  Manager servers, starting with the publication server and the TFTP server.

  Note:

  When you apply a device Package to activate the new device support, a broad cluster restart is necessary for these devices to record successfully.

  A

  Cluster - wide restart is not required when you apply a Package of device for the update of the existing firmware/media. Cisco Unified Communications Manager 8.6, you perform all software installations and upgrades by using the software update menu options. The system can load and process only the software that Cisco has approved. You may not install or use third party or Windows - software applications that you used a previous version of Cisco Unified Communications Manager.

  1 from your web browser, go to the web page of Cisco Unified Communications Administration of the operating system.

  2. in the menu of the software upgrades, select Install/Upgrade.

  3. fill in the appropriate values in the section where the software and click Next.

  4. in the available software drop-down list box, select the device package file

  Click next

  5. check that the MD5 has the correct value. Click Next.

  6. in the warning box, verify that you have selected the right firmware and

  then click on install.

  7. check that you have received a message of success.

  Note:

  If you restart the cluster, skip step 8.

  8. stop and restart the TFTP server.

  9 reset the devices concerned to upgrade the devices to the new load.

  Hope that helps

  Concerning

  KR Ravi

• Speech and cisco Unity Connection connect

  Hi all, I've read that speech Connect is available for Cisco Unity Connection Version 7.1.3 and later versions. I installed CUC7.1.3 and CUCM 7.1.3 and I would like to configure this feature.

  If someone have this plase share tips or a document.

  Thank you very much

  David

  Speech Connect is actually integrated in the application of the CUC.  There really isn't any special rig or something like you would have with speech Connect for the unit. When you choose ' enable voice ' Manager directory or AA and you search by name, which is essentially the engine speech connect to work. "  If the user has a registered name, you will hear him play.  If this isn't the case, YOUSSOUF (AutoAttendant activated by speech) will deliver the names for you.

  Hailey