Client VPN WRVS4400N

Similar Questions

• configuration VPN WRVS4400N

  I have a wrvs4400n intending to allow VPN access to my computer at home instead of simple RDP using port forwarding.  However, I can not understand how to configure the VPN wrvs4400n.  I don't think that I need a tunnel as the connection from my laptop will be different locations depending on where I'm travelling to.  My home network has a dynamic IP address, but I set it up with dyndns.org, so I know the IP address all the time.  I hope that this will be a simple task, but it turns out that I'm dead in the water...  All advice and support would be greatly appreciated.

  The joint should help you get started using the QuickVPN Client, which can connect to your WRVS4400N at home from the internet.

• Can I have a copy of KB2982791? My client VPN application

  Original title: Please, please, please can I have a copy of KB2982791? My client VPN application

  Yes, I am aware that MS has w / drew this patch.

  However, I don't have the choice. I SHOULD have the patch and am willing to take the risk. My client is a Government, and their VPN is administered by people who insist that I have this patch in order to do my job.

  Can I PLEASE have the patch? If my system has problems, I'll take the risk. I can't change my client--their admins VPN will ALWAYS REQUIRE MS PATCHES, even if MS released their.

  I implore anyone who wants to hear it.

  Computers belongs to me - I'm an entrepreneur owner unique to Montgomery Co. MD [whose] VPN is administered by people who insist that I have this patch in order to do my job.

  Well, I'm afraid that you are between the proverbial rock and hard place, my friend.

  KB2982791 was "fired" shortly before midnight (Pacific time) on August 15, 2014. KB2982791 is no longer available through Windows Update. KB2982791 is no longer available via the MS Download Center or from the Microsoft Update Catalog. In addition, Microsoft informed uninstall KB2982791 if it is currently installed.

  If the admins of the County cannot understand the FAQ update on this page...

  
  Why this bulletin has been revised August 15, 2014?
  Microsoft revised this bulletin to address known issues related to the installation of security update 2982791. Microsoft is investigating the behavior associated with the installation of this update and will update this bulletin when more information is available. Microsoft recommends customers to uninstall this update. As an additional precaution, Microsoft has removed the 2982791 security update download links. For instructions on how to uninstall this update, see Microsoft Knowledge Base Article 2982791.

  .. .you need to slam a few heads together (or contact their TAM Microsoft).

  I suspect upgrading kernel (MS14-045) re-Mode drivers - will be released very soon (for example, early next week?), probably under a new KB number. [Those who say cannot know & those who say can't know.]

  Good luck on Monday morning!

  PS: Here is the consumer, specific peer-to-peer support forums. You'd better post in Win7 IT Pro-specifiques forums-online http://social.technet.microsoft.com/Forums/windows/en-US/home#category=w7itpro [or in the forums partner if you are a MS Partner]

• Client VPN connectivity problems

  I use the cisco VPN client to connect to our network, located behind a 515E. The client is authenticated and gets an ip address but cannot ping or connect with one of the hosts. The connection is to a network of customers that is also behind a 515E. I have successfully connected using the same policy to other places and have had no problem. What confuses me, is that we have used to have a Netscreen firewall before and he had a netscreen vpn client which connected since their network with a problem. Is that something they need for their firewall so that we can get through the traffic?

  Try to turn on NAT - T on your pix, by setting up:

  ISAKMP nat-traversal 20

  and configure the client vpn accordingly:

  http://www.Cisco.com/warp/public/471/cvpn_3k_nat.html#conf_client

  I think these discussions are useful:

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=virtual%20Private%20Networks&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dd7dda4

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=virtual%20Private%20Networks&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dd7fe80

• Definition of domain DNS client VPN

  This seems to be a simple question, but I have difficulty finding an answer. Connect to a VPN 3000 using the client VPN Cisco 4.0. Is there a setting that I can do on the 3000 that will set the domain name DNS on the client. I have it plugged into the hub and he gave me an IP address, the list of list of WINS servers, DNS servers,... but it has not defined the domain name for the connection. Is this possible?

  Thank you

  Greg

  Configuration - users - groups - Client Config - default domain name management

• The VPN client VPN connection behind other PIX PIX

  I have the following problem:

  I wanted to establish the VPN connection the client VPN to PIX on GPRS / 3G, but I didn t have a bit of luck with PIX IOS version 6.2 (2).

  So I upgraded PIX to 6.3 (4) to use NAT - T and VPN client to version 4.0.5

  I have configured PIX with NAT-T(isakmp nat-traversal 20), but I still had a chance, he would not go through the 1st phase. As soon as I took nat-traversal isakmp off he started working, and we can connect to our servers.

  Now, I want to connect to the VPN client behind PIX to our customer PIX network. VPN connection implements without problem, but we can not access the servers. If I configure NAT - T on the two PIX, or only on the customer PIX or only on our PIX, no VPN connection at all.

  If I have to connect VPN client behind PIX to the customer's network and you try to PING DNS server for example, on our PIX, I have following error:

  305006: failed to create of portmap for domestic 50 CBC protocol translation: dst outside:194.x.x.x 10.10.1.x

  194.x.x.x is our customer s address IP PIX

  I understand that somewhere access list is missing, but I can not understand.

  Of course, I can configure VPN site to site, but we have few customers and take us over their servers, so it'd just connect behind PIX VPN and client connection s server, instead of the first dial-in and then establish a VPN connection.

  Can you please help me?

  Thank you in advan

  The following is extracted from ASK THE DISCUSSION FORUM of EXPERTS with Glenn Fullage of Cisco.

  I've cut and pasted here for you to read, I think that the problem mentioned below:

  Question:

  Hi Glenn,.

  Following is possible?

  I have the vpn client on my PC, my LAN is protected by a pix. I can launch the vpn client to connect to remote pix. Authenticates the vpn client and the remote pix makes my PC with the assigned ip appropriate to its pool of ip address.

  The problem that I am facing is that I can not anything across the pix remote ping from my PC which is behind my pix. Can you please guide me what I have to do to make this work, if it is possible?

  My PC has a static ip address assigned with the default gateway appropriate pointing to my s pix inside interface.

  Thank you very much for any help provided in advance.

  Response from Glenn:

  First of all, make sure that the VPN connection works correctly when the remote PC is NOT behind a PIX. If that works fine, but then breaks when put behind a PIX, it is probably that the PIX is PAT, which usually breaks IPSec. Add the following command on your PIX VPN client is behind:

  fixup protocol esp-ike

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/df.htm#wp1067379 for more details.

  If it still has issues, you can turn on NAT - T on the remote PIX that ends the VPN, the client and the remote PIX must encapsulate then all IPSec in UDP packets that your PIX will be able to PA correctly. Add the following command on the remote PIX:

  ISAKMP nat-traversal

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.

  NAT - T is a standard for the encapsulation of the UDP packets inot IETF IPSec packets.

  ESP IPSec (Protocol that use your encrypted data packets) is an IP Protocol, it is located just above IP, rather than being a TCP or UDP protocol. For this reason, it has no TCP/UDP port number.

  A lot of features that make the translation of address of Port (PAT) rely on a single to PAT TCP/UDP source port number ' ing. Because all traffic is PAT would be at the same source address, must be certain uniqueness to each of its sessions, and most devices use the port number TCP/UDP source for this. Because IPSec doesn't have one, many features PAT fail to PAT it properly or at all, and the data transfer fails.

  NAT - T is enabled on both devices of the range, they will determine during the construction of the tunnel there is a PAT/NAT device between them, and if they detect that there is, they automatically encapsulate every IPSec packets in UDP packets with a port number of 4500. Because there is now a port number, PAT devices are able to PAT it correctly and the traffic goes normally.

  Hope that helps.

• Client VPN does not install

  Greetings,

  Try to install the VPN clinet version 5.0.07.0290 on WinXP box.

  Gets to a certain point then - error

  Error 27850.  Unable to manage the network components.

  The corruption of the operating system can prevent installation.

  I asked this question here before - and received responses instructioning me to uninstall the client.

  This canoe do since there is no element installed in Add / Remove programs to point to uninstall.  I deleted the folder created, but it makes no difference - each time the system stops at the same point.

  Any other ideas?

  Is your Windows XP 32-bit or 64-bit?

  There are 2 version of VPN Client 5.0.07.0290:

  32-bit: vpnclient-win-msi - 5.0.07.0290 - k9.exe

  64-bit: vpnclient-winx64-msi - 5.0.07.0290 - k9.exe

  Please, please make sure you use the right software.

  Here are the steps that will allow the uninstall:

  (1) remove the VPN Client (any version) of the machine using the MSI cleanup tool
  http://support.Microsoft.com/kb/290301

  Updated the DNE using this deterministic networks link
  http://www.deterministicnetworks.com/support/dnesupport.asp

  Run the WINFIX application, then the upgrade DNE.

  (2) take a backup of the registry.
  (3) on your desktop, click Start > run and type regedit.
  (4) delete the following keys:

  (a) go to HKEY_LOCAL_MACHINE > SOFTWARE > Cisco Systems > customer VPN.
  (b) go to HKEY_LOCAL_MACHINE > SOFTWARE > deterministic networks and remove the keys.
  Note: Sometimes the system will not allow deletion of this key.

  (c) go to HKEY_LOCAL_MACHINE > SOFTWARE > Microsoft > Windows > CurrentVersion > uninstall > {5624c000-b109-11d4-9db4-00e0290fcac5}.
  (d) delete all the old files deterministic NDIS Extender (DNE): all files starting with DNE, as all are coming files and Client VPN facilities.

  dne2000.sys %SystemRoot%\system32\drivers
  dne2000m.inf and dne2000m.pnf of %SystemRoot%\inf

  (e) the enumeration of original manufacturers of hardware (OEM) of the dne2000.inf and dne2000.pnf files.

  The OEM enumeration .inf file is a file called ".inf oem (digital value)."
  For example, oem2.inf and oem2.pnf.

  Note: Be sure to remove only the DNE OEM files.

  dneinobj.dll % SystemRoot%\system32. You may need to reboot for this file can be deleted.

  (f) delete the following file: cvpndrv.sys to %SystemRoot%\system32\drivers

  (5) reboot the machine.

  (6) find the file CSGina.dll in the system32 folder rename it to CSGina.old

  7-restart the machine.

  (8) to disable any firewall if not installed.

  Hope that helps.

• Client VPN routing issue

  I am trying to configure client vpn software ver 5.0 for remote to connect to the local network behind a 1801 users.

  I can get the client saying its connected but traffic is not circulate outside in:

  When I try to ping an address 192.168.2.x behind the 1801 I get a response from the public ip address but then when I try to ping to another address I have no answer.

  I guess the question is associated with NAT.

  Here is my config, your help is apprecited

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  host name C#.

  !

  boot-start-marker

  boot-end-marker

  !

  enable password 7 #.

  !

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  AAA - the id of the joint session

  !

  IP cef

  !

  IP domain name # .local

  property intellectual auth-proxy max-nodata-& 3

  property intellectual admission max-nodata-& 3

  !

  Authenticated MultiLink bundle-name Panel

  !

  username password admin privilege 15 7 #.

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 1801Client

  key ##############

  DNS 192.168.2.251

  win 192.168.2.251

  field # .local

  pool VpnPool

  ACL 121

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap throwing crypto

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  Archives

  The config log

  hidekeys

  !

  property intellectual ssh time 60

  property intellectual ssh authentication-2 retries

  !

  interface FastEthernet0

  address IP 87. #. #. # 255.255.255.252

  IP access-group 113 to

  NAT outside IP

  IP virtual-reassembly

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface BRI0

  no ip address

  encapsulation hdlc

  Shutdown

  !

  interface FastEthernet1

  interface FastEthernet8

  !

  ATM0 interface

  no ip address

  Shutdown

  No atm ilmi-keepalive

  DSL-automatic operation mode

  !

  interface Vlan1

  IP 192.168.2.245 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  !

  IP pool local VpnPool 192.168.3.200 192.168.3.210

  no ip forward-Protocol nd

  IP route 0.0.0.0 0.0.0.0 87. #. #. #

  !

  !

  no ip address of the http server

  no ip http secure server

  the IP nat inside source 1 interface FastEthernet0 overload list

  IP nat inside source static tcp 192.168.2.251 25 87. #. #. # 25 expandable

  Several similar to the threshold with different ports

  !

  access-list 1 permit 192.168.2.0 0.0.0.255

  access-list 113 allow host tcp 82. #. #. # host 87. #. #. # eq 22

  access-list 113 permit tcp 84. #. #. # 0.0.0.3 host 87. #. #. # eq 22

  access-list 113 allow host tcp 79. #. #. # host 87. #. #. # eq 22

  access-list 113 tcp refuse any any eq 22

  access-list 113 allow host tcp 82. #. #. # host 87. #. #. # eq telnet

  access-list 113 permit tcp 84. #. #. # 0.0.0.3 host 87. #. #. # eq telnet

  access-list 113 allow host tcp 79. #. #. # host 87. #. #. # eq telnet

  access-list 113 tcp refuse any any eq telnet

  113 ip access list allow a whole

  access-list 121 permit ip 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255

  access-list 121 allow ip 192.168.3.0 0.0.0.255 192.168.2.0 0.0.0.255

  !

  control plan

  !

  Line con 0

  line to 0

  line vty 0 4

  transport input telnet ssh

  !

  end

  you have ruled out the IP address of the customer the NAT pool

  either denying them in access list 1

  or do road map that point to the loopback address as a next hop for any destent package for your pool to avoid nat

  first try to put this article in your access-lst 110

  access-list 110 deny 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255

  access-list 110 permit 192.168.2.0 0.0.0.255 any

  sheep allow 10 route map

  corresponds to the IP 110

  remove your old nat and type following one

  IP nat inside source overload map route interface fastethernet0 sheep

  rate if useful

  and let me know, good luck

• Connection with the client VPN for RV110W problem

  Hi guys: I just installed a RV110W router to my small business and I try to connect via VPN from home client.  I was unable to do so, no matter what I try.  Relevant information:

  1. I can connect to the router via remote very well management, so I know that the router is accessible from the Net.

  2. internal address of the router: 10.81.208.1

  3. active PPTP.  PPTP server IP address: 10.0.0.1

  4 IP addresses for PPTP clients: 10.0.0.10 - 14

  5. two VPN clients added - one with PPTP, with the QuickVPN Protocol Protocol.  Both are enabled (and Yes, I triple checked passwords)

  6 encryption MPPE and Netbios active.

  7 IPSec, PPTP and L2TP all active gateways.

  8 VPN client: 1.4.1.2

  9. computer: laptop running Windows 7 family (64-bit), with the firewall Windows is activated.

  10 home network: 192.168.2.196

  It is causing to tear my hair out.  What Miss me?

  Shannon

  Hi Shannon,

  I am pleased to see that you're progress.

  Shannon Rotz wrote:
  I changed the RM port to 443.  Unfortunately, now I can't connect to the router via browser, either by remote management or from the local network - I get the usual "page cannot be displayed".  How do I get back into the router configuration GUI?
  

  You should be able to reach the GUI by typing https://192.168.1.1(assuming that you have not changed the default IP address) normally once you replace http (port 80) with https (port 443) the internal router web server automatically will redirect you to the https page if you type http. Open your command prompt and try to do a ping of the IP address of the router to ensure that it still meets this address

  With regards to the VPN client:   Up until I changed the port, the same error message kept coming up, i.e. "Unable to establish connection" (or something like that), with a list of possible reasons why it couldn't connect. Now the message has changed - I'm getting "Server's certificate doesn't exist on your local computer".  If I continue trying to connect, then it says "Activating Policy", followed by "Verifying Network", then "The remote gateway is not responding.  Do you want to wait?"  This is definitely progress, since I never got this far before.

  You are a quarter inch offline. If you look at the log.txt in C:\Program Cisco Small Business\QuickVPN Client, in my view, you will see "Failed to ping router remote VPN! This means that your PC is blocking the ping to the router response. Usually, if you look at this point the status of Client VPN in the router (first of all need to remote management) you will see that your user status is "connected." If the router thinks that the connection is established, but the PC does not work. You might want to try another PC at this stage to verify that it is indeed a problem with your PC. This problem is usually caused by the 3rd party software antivirus/firewall blocking the ping response. Microsoft Security Essentials can do this as well, so if you turn it off. If you do not have another PC to test from, call Cisco Small Business Support and ask a technician, try to connect to the lab. You can find the number to call here

  On an impulse, I tried setting up a Windows VPN connection, i.e. created a new VPN connection in Network and Sharing Center, using a PPTP client ID that I had created.  That connection actually worked, except for one problem:  I can't see the remote network.  If I could solve that problem, I'll just tell the other clients to use a Windows connection rather than QuickVPN.
  

  Good thought. If you do not see the remote devices, make sure that they do not block VPN connections. (Windows or third-party firewall, antivirus, antispyware) With a connection, PPTP or QuickVPN, you should be able to go to run, type the IP address of the device that you want to connect to (i.e. \\192.168.1.101 ) and see the list of shared folders. After the PPTP connection is established, try to ping the address LAN IP of the router. If it is successful, try to ping a LAN device such as a network printer or a PC. Again, PCs may block ping requests if they have a firewall running watch so for this.

  Answer please if you have any questions.

• Client VPN router IOS, and site to site vpn

  Hello

  Im trying to configure a vpn client access to an ios router that already has a vpn site-to site running. I don't see how the two can run on the same router.

  So I guess my question is is it possible? and if anyone has therefore had a config that they can share or a useful link.

  IM using a router 800 series with 12.4 ios

  Thank you very much

  Colin

  ReadersUK wrote:
  Hi
  Im trying to configure access for a vpn client to a ios router that already has a site to site vpn running. I cant see how both can be running on the same router.
  So i guess my question is can this be done? and if so has anyone got a config they can share or a useful link.
  im using a 800 series router with 12.4 ios
  Many thanks
  Colin
  

  Colin

  It can be done. Look at this config example that shows a router configured with a site to site VPN and client vpn - connection

  https://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094685.shtml

  Jon

• Client VPN will travel not connected via 877w

  Hello

  I've implemented a Cisco 877w and it works very well for web access

  Client VPN on my laptop connects via the 877w and authenticates on my remote work ASA5510 firewall.

  Problem is after you connect to the ASA, I can not connect anything internally work network (10.0.0.0/24), ping, etc. RDP is back with no answer.

  I've attached the config, can someone tell me what I am missing, might access a list?

  Thanks for your help

  Chris

  This router is made PAT/NAT, Ipsec blocking.

  Activate Nat on the ASA course remote.

  ISAKMP nat - t or crypto isakmp nat - t

  HTH

  Sangaré

  Pls rate helpful messages

• Client VPN Cisco router Cisco, MSW CA + certificates

  Dear Sirs,
  Let me approach you on the following problem.

  I wanted to use a secure between the Cisco VPN client connection
  (Windows XP) and Cisco 2821 with certificate-based authentication.
  I used the Microsoft certification authority (Windows 2003 server).
  Cisco VPN client used eTokenPRO Aladdin as a certificate store.

  Certificate of MSW CA registration and implementation in eToken ran OK
  Customer VPN Cisco doesn't have a problem with the cooperation of eToken.
  Certificate of registration of Cisco2821 MSW ca ran okay too.

  Cisco 2821 configuration is standard. IOS version 12.4 (6).

  Attempt to connect to the client VPN Cisco on Cisco 2821 was
  last update of the error messages:

  ISAKMP: (1020): cannot get router cert or routerdoes do not have a cert: had to find DN!
  ISAKMP: (1020): ITS been RSA signature authentication more XAUTH using id ID_FQDN type
  ISAKMP (1020): payload ID
  next payload: 6
  type: 2
  FULL domain name: cisco - ca.firm.com
  Protocol: 17
  Port: 500
  Length: 25
  ISAKMP: (1020): the total payload length: 25
  ISAKMP (1020): no cert string to send to peers
  ISAKMP (1020): peer not specified not issuing and none found appropriate profile
  ISAKMP (1020): Action of WSF returned the error: 2
  ISAKMP: (1020): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
  ISAKMP: (1020): former State = new State IKE_R_MM5 = IKE_P1_COMPLETE

  Is there some refence where is possible to find some information on
  This problem? There is someone who knows how to understand these mistakes?
  Thank you very much for your help.

  Best regards
  P.Sonenberk

  PS Some useful information for people who are interested in the above problem.

  Address IP of Cisco 2821 10.1.1.220, client VPN IP address is 10.1.1.133.
  MSW's IP 10.1.1.50.
  Important parts of the Cisco 2821 configuration:

  !
  cisco-ca hostname
  !
  ................
  AAA new-model
  !
  AAA authentication login default local
  AAA authentication login sdm_vpn_xauth_ml_1 local
  AAA authorization exec default local
  AAA authorization sdm_vpn_group_ml_1 LAN
  !
  ...............
  IP domain name firm.com
  host IP company-cu 10.1.1.50
  host to IP cisco-vpn1 10.1.1.133
  name of the IP-server 10.1.1.33
  !
  Authenticated MultiLink bundle-name Panel
  !
  Crypto pki trustpoint TP-self-signed-4097309259
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 4097309259
  revocation checking no
  rsakeypair TP-self-signed-4097309259
  !
  Crypto pki trustpoint company-cu
  registration mode ra
  Enrollment url http://10.1.1.50:80/certsrv/mscep/mscep.dll
  use of ike
  Serial number no
  IP address no
  password 7 005C31272503535729701A1B5E40523647
  revocation checking no
  !
  TP-self-signed-4097309259 crypto pki certificate chain
  certificate self-signed 01
  30820249 308201B 2 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
  .............
  FEDDCCEA 8FD14836 24CDD736 34
  quit smoking
  company-cu pki encryption certificate chain
  certificate 1150A66F000100000013
  30820509 308203F1 A0030201 02020 HAS 11 092A 8648 01000000 13300 06 50A66F00
  ...............
  9E417C44 2062BFD5 F4FB9C0B AA
  quit smoking
  certificate ca 51BAC7C822D1F6A3469D1ADC32D0EB8C
  30820489 30820371 A0030201 BAC7C822 02021051 D1F6A346 9D1ADC32 D0EB8C30
  ...............
  C379F382 36E0A54E 0A6278A7 46
  quit smoking
  !
  ...................
  crypto ISAKMP policy 30
  BA 3des
  md5 hash
  authentication rsa-BA
  Group 2
  ISAKMP crypto identity hostname
  !
  Configuration group customer isakmp crypto Group159
  key Key159Key
  pool SDM_POOL_1
  ACL 100
  !
  the crypto isakmp client configuration group them
  domain firm.com
  pool SDM_POOL_1
  ACL 100
  !
  Crypto ipsec transform-set esp-3des esp-md5-hmac 3DES-MD5
  !
  crypto dynamic-map SDM_DYNMAP_1 1
  the transform-set 3DES-MD5 value
  market arriere-route
  !
  card crypto SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
  map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto
  client configuration address map SDM_CMAP_1 crypto answer
  map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
  !
  ................
  !
  end

  status company-cu of Cisco-ca #show cryptographic pki trustpoints
  Trustpoint company-cu:
  Issuing CA certificate configured:
  Name of the object:
  CN = firm-cu, dc = company, dc = local
  Fingerprint MD5: 5026582F 8CF455F8 56151047 2FFAC0D6
  Fingerprint SHA1: 47B 74974 7C85EA48 760516DE AAC84C5D 4427E829
  Universal router configured certificate:
  Name of the object:
  host name = cisco - ca.firm.com
  Fingerprint MD5: E78702ED 47D5D36F B732CC4C BA97A4ED
  Fingerprint SHA1: 78DEAE7E ACC12F15 1DFB4EB8 7FC DC6F3B7E 00138
  State:
  Generated keys... Yes (general purpose, not exportable)
  Authenticated issuing certification authority... Yes
  Request certificate (s)... Yes

  Cisco-ca #sh crypto pubkey-door-key rsa
  Code: M - configured manually, C - excerpt from certificate

  Name of code use IP-address/VRF Keyring
  C Signature name of X.500 DN default:
  CN = firm-cu
  DC = company
  DC = local

  C signature by default cisco-vpn1

  IMPORTANT: I don't have a Cisco IOS Software: 12.4 (5), 12.3 (11) T08, 12.4 (4.7) PI03c,.
  12.4 (4.7) T - there is error in the cryptographic module.

  Hey guys, it's weird that the router is not find cert after IKE is the cert and validates, it is certainly not reason, but I would go ahead and set up the mapping of certificate on this router to force the client to associate with Group of IKE, for that matter, that you need to change your config a bit for use iskamp profiles :

  http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t8/feature/guide/gt_isakp.html

• How to install MX60 and activate client vpn services

  Can someone show me a link or a video that helps install MX60 and activate client VPN services?

  https://KB.Meraki.com/Knowledge_base/small-remote-or-Home-Office-VPN-opt...

• Client VPN not open or connect

  Hello

  I'm currently running Client VPN 5.0.07.0440 on a Windows 7 Pro HP TouchSmart. The .pcf file is that the same iI uses the same network on many other om of machines.  When I double click the icon, the window opens, but when I double click on the login entry, the dialog box shows 'connection to the gateway security to xxx.xxx.xxx.xxx for a few seconds and then says no 'connected'.  I can't even login screen I can normally. This is a new mode of computer. All updates are downloaded for windows.

  I uninstalled the client and re-installed it re-boot after each step. I have ping for the address and had no problems. Avast, Malwarebytes as on other machines running. No other security software. My VPN is enabled in my network connections.

  Here is my log file:

  Cisco Systems VPN Client Version 5.0.07.0440
  Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
  Customer type: Windows, Windows NT
  Running: 6.1.7600
  Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\
   
  1 13:05:53.644 05/07/14 Sev = WARNING/3 IKE/0xE3000057
  The HASH payload received cannot be verified
   
  2 13:05:53.644 05/07/14 Sev = WARNING/2 IKE/0xE300007E
  Failed the hash check... may be configured with password invalid group.
   
  3 13:05:53.644 05/07/14 Sev = WARNING/2 IKE/0xE300009B
  Impossible to authenticate peers (Navigator: 915)
   
  4 13:05:53.645 05/07/14 Sev = WARNING/2 IKE/0xE30000A7
  SW unexpected error during the processing of negotiator aggressive Mode:(Navigator:2263)

  I know the names and passwords are correct, as they were copied from work files.

  Hope this is posted in the right group.

  Never had this problem after a lot of machines. Any help would be greatly appreciated.

  Thank you

  Since you get the message 'can be configured with password invalid group", perhaps your FCP file has been corrupted.

  I would recommend that you compare the profile pcf file (stored in "C:\Program Files (x 86) \Cisco Client\Profiles") on the machine of non-working with a working configuration.

  They can be viewed in a text editor or with a comparison (like the freeware ExamDiff) tool. The hashes from encrypted password Group (string in file preceded by "enc_GroupPwd =") must match.

• Client VPN with tunneling IPSEC over TCP transport does not

  Hello world

  Client VPN works well with tunneling IPSEC over UDP transport.

  I test to see if it works when I chose the VPN client with ipsec over tcp.

  Under the group policy, I disabled the IPSEC over UDP and home port 10000

  But the VPN connection has failed.

  What should I do to work VPN using IPSEC over TCP

  Concerning

  MAhesh

  Mahesh,

  You must use "ikev1 crypto ipsec-over-tcp port 10000.

  As crypto isakmp ipsec-over-tcp work on image below 8.3

  HTH