configuration VPN WRVS4400N
I have a wrvs4400n intending to allow VPN access to my computer at home instead of simple RDP using port forwarding. However, I can not understand how to configure the VPN wrvs4400n. I don't think that I need a tunnel as the connection from my laptop will be different locations depending on where I'm travelling to. My home network has a dynamic IP address, but I set it up with dyndns.org, so I know the IP address all the time. I hope that this will be a simple task, but it turns out that I'm dead in the water... All advice and support would be greatly appreciated.
The joint should help you get started using the QuickVPN Client, which can connect to your WRVS4400N at home from the internet.
Tags: Cisco Support
Similar Questions
-
I am interested in establishing a VPN for my computer. I looked at some of the information to help Ms. I'm missing something in the way of understanding how do or end the connection.
You can configure VPN regardless of static or dynamic IP, both are possible. You can refer to:
-
LT2P configuration vpn cisco asa with the internet machine windows/mac issue
Dear all,
I have properly configured configuration vpn L2TP on asa 5510 with 8.0 (4) version of IOS.
My internet does not work when I connect using the vpn. Even if I give power of attorney or dns or I remove the proxy
It does not work. only the resources behind the firewall, I can access. I use the extended access list
I tried also with the standard access list.
Please please suggest what error might be.
Thank you
JV
Split for L2TP over IPSec tunnel tunnel is not configured on the head end (ASA), it must be configured on the client itself, in accordance with the following Microsoft article:
-
Need help to configure VPN NAT traffic to ip address external pool ASA
Hello
I need to configure vpn NAT ip address traffic external pool ASA
For example.
Apart from the ip address is 1.1.1.10
VPN traffic must be nat to 1.1.1.11
If I try to configure policy nat or static nat ASA gives me error "global address of overlap with mask.
Please, help me to solve this problem.
Thank you best regards &,.
Ramanantsoa
Thank you, and since you are just 1 IP 1.1.1.11 Polo, the traffic can only be initiated from your site to the remote end.
Here is the configuration of NAT:
access list nat - vpn ip 192.168.1.0 allow 255.255.255.0 10.0.0.0 255.255.0.0
NAT (inside) 5 access list nat - vpn
Overall 5 1.1.1.11 (outside)
In addition, the ACL crypto for the tunnel from site to site should be as follows:
access-list allow 1.1.1.11 ip host 10.0.0.0 255.255.0.0
Hope that helps.
-
Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router
Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device.
Someone please please suggest me something as soon as POSSIBLE.
Thank you
CLI version:
ASDM and SDM Version:
-
Configuration of CISCO VPN (WRVS4400N) router
Dear,
Please help me to setup VPN connection,
Headquarters: firewall fortigate-200B - SSL, IPsec
Branch: WRVS4400N Wireless-N Gigabit Security Router with VPN
The two sides have the public IP address
Wrong forum, post in the 'small business routers. You can move your ad using the Panel on the right actions.
-
I can not to reach the QuickVPN Client Gateway (WRVS4400N) and paste parts of the journal on this subject.
Help please?
********************************************************Logs from The Client*************************************************************************************
2013/02/28 11:33:03 [STATUS] OS Version: unknown
2013/02/28 11:33:03 [STATUS] a network interface detected with the IP 10.100.51.53
2013/02/28 11:33:03 [STATUS] connection...
Address of the VPN entry Server 2013/02/28 11:33:03 [DEBUG] = 108.132.169.44
2013/02/28 11:33:03 [STATUS] connection to a remote gateway with IP address: 108.132.169.44
2013/02/28 11:33:14 remote gateway [WARNING] has not been achieved...
2013/02/28 11:33:14 [WARNING] failed to connect.
2013/02/28 11:33:14 [WARNING] server certificate does not exist on your local computer.
2013/02/28 11:33:20 remote gateway [STATE] has been reached with https...
2013/02/28 11:33:20 [STATUS] commissioning...
2013/02/28 11:33:23 [STATUS] success of connect.
2013/02/28 11:33:23 [STATUS] Tunnel is configured. Ping test will begin.
2013/02/28 11:33:23 [STATUS] verification of network...
2013/02/28 11:33:29 [WARNING] failed to do a remote VPN router ping!
2013/02/28 11:33:32 [WARNING] failed to do a remote VPN router ping!
2013/02/28 11:33:35 [WARNING] failed to do a remote VPN router ping!
2013/02/28 11:33:38 [WARNING] failed to do a remote VPN router ping!
2013/02/28 11:33:41 [WARNING] failed to do a remote VPN router ping!
2013/02/28 11:33:54 [WARNING] Ping has been blocked, which can be caused by an unexpected disconnection.
2013/02/28 11:33:56 [STATUS] disconnection...
2013/02/28 11:34:02 [STATUS] success of disconnect.
*******************************************************Logs from the WRVS4400N******************************************************************************
28 FEV 10:55: 22 - [VPN Log]: added the description of the connection "test_rw_rw".
28 FEV 10:55: 22 - [VPN Log]: listen to IKE messages
28 FEV 10:55: 22 - [VPN Log]: forget the secrets
28 FEV 10:55: 22 - [VPN Log]: loading of secrets "/ etc/ipsec.secrets '.
28 FEV 10:56 - [VPN Log]: 'test_rw_rw': removal of connection
Thank you
Orlando
Hi, orlando, please use our forum, my name is Johnnatan and I'm part of the community of support to small businesses. When you configure a remote VPN connection, there are certain steps that are lost on the way, I created a document for the ths kind of questions, you can see here, if you have any questions, please let me know and I´ll help you. I hope you find this answer useful,
"* Please mark the issue as response or write it down so others can benefit from.
Greetings,
Johnnatan Rodriguez Miranda.
Support of Cisco network engineer.
-
Hi all
We have a customer who has recently changed Vedors and came to us. We had to change the ISP and the need to make changes in their firewall. I went out on the site and has not been able to get into the routers and I contacted the previos company but they do not release this information. We have therefore had to reset devices and put everything up. Everything works great except before having an IPSEC VPN Tunnel between the 2 buildings. Both buildings have routers WRVS4400N and I configured a VPN IPSEC Tunnel on both sides. I named the same and the summary says that both are on the rise. But when I try to go from one side to the other, I am unable to Ping or solve anything. I'll put all the information I can find are relavent to this problem and hope someone can help me. I called Cisco, but they said they are out of warranty and will not be able to help. Cisco directed me here.
Site A:
Internal:
192.59.1.1 (IP)
255.255.255.0 (SN)
External:
96.10.218.14 (IP)
255.255.255.252 (SN)
96.10.218.13 (GW)
24.25.5.60 (DNS1)
24.25.5.61 (DNS2)
Site b:
I internal:
192.39.1.1 (IP)
255.255.255.0 (SN)
External:
50.52.145.50 (IP)
255.255.255.252 (SN)
50.52.145.49 (GW)
184.16.4.22 (DNS1)
184.16.33.54 (DNS2)
V Tunnels PN
Site has
Site B
For security purposes the IP addresses are not exactly what is displayed, but I checked 10 times and they correspond to the remote site said. Yet once again, say that they are on the rise, but I am unable to ping or see the tunnel devices. Help, please.
Thanks in advance
Mike
The problem is most likely in the 'Local Group' configuration. How they are implemented is essentially to allow only the 192.39.1.1 and 192.59.1.1 talk to each other. These fields should be read as the subnet as this ID: 192.39.1.0 and 192.59.1.0
Try this restart of the tunnels, and let us know how it worked.
-
VPN WRVS4400N out of the box?
Hello
I am looking to buy a WRVS4400N and I was just wondering if it comes with everything you need to configure the VPN (terminated on the router) "out of the box"? Or do you need to purchase additional software or certificates?
Thank you very much
Dan
OK, there isn't any addition to buy or certificate to buy software.
Jason Bryant
Support Cisco engineer
-
Using to relay DHCP on LAN remote IPSec VPN WRVS4400N
Hello
I have a WRVS4400N. I want to know if it is possible to configure the remote relay DHCP WRVS4400N to find a DHCP server on the local network. The local network is 192.168.2.0/24, and the Remote LAN is 192.168.1.0/24. I am entered the field of relay DHCP server 192.168.1.100 but my local PC does not get an IP address. So, I would like to than the local PC to get an IP from DHCP address 192.168.2.x server remote (LAN) through the IPSec VPN tunnel. Is this possible?
The IPSec tunnel works. I ping the 192.168.1.100 remote DHCP server, if the local PC, a static IP address 192.168.2.x I have the configuration of the DHCP server with an IP of 192.168.2.x/24 range.
The remote VPN router is a Netgear FVS114.
Thank you
NIC
The wrvs4400n, you cannot do the dhcp relay in the vpn tunnel. You may need to get a business for which solution or a connection point to point for both networks on the same local network configuration.
-
Configuration VPN FVS336G V3 FW 4.3.3 - 6:
I just bought this firewall and I'm trying to configure a gateway VPN tunnel. I used the VPN Wizard and it worked well. However, when I try to change the 3DES, AES-256 encryption, it works very well for the IKE policy, but when I try to change the VPN policy encryption in the section Auto to AES - 256 policy setting, it says I need to configure some parameters of manual strategy before accepting my change. This seems not correct - I'm not trying to enter manual policy parameters. Is this a bug?
JohnRo
I reloaded the firmware, restore the default and restored the settings that I saved and VPN policy page seems to work fine now.
Thank you!
John
-
Configuration VPN windows server 2012 essencial
What policy I need to add in the game until I will configure the VPN in windows server 2012 essential? because when I install the remote access roles I received a message when done that mention me politics. later I activate access and remote access and I can't access the internet, I disable access and remote access to I can connect to internet from my server.
There is no forums for Windows Server community. Windows Server forums are on the Technet site. http://social.technet.Microsoft.com/forums/en-us/home?category=WindowsServer
-
WRT1900AC cannot configure VPN
I CURRENTLY HAVE 2 WIRELESS ROUTERS AN ASUS RT-N56U WHICH WAS EASY to set UP WITH ExpressVPN. COMING TO EXPAND MY NETWORK & IMPROVE USING A LINKSIS WRT1900AC. UNABLE TO SET TO THE TOP OF THE SAME. BOTH ROUTERS ARE HARD CABLES TO THE ISP ROUTER & WILL BE POSITIONED AT DIFFERENT AREAS OF THE HOUSE FOR COVER. I HAVE THE ExpressVPN PAST & DETAILS USER password, LIST OF GLOBAL SERVER ADDRESSES & THEIR ADDRESSES IP CONCERNED.
CAN SOMEONE HELP ME IN THE BASIC CONFIGURATION. I AM NOT AN IT WIZZ BUT YOU CAN FOLLOW THE INSTRUCTIONS ESPECIALLY WITH SCREENSHOTS SUPPORTED. HELP IS GREATLY APPRECIATED.
OK gents,
Answers very well. It gives me a lot to think so thank you very much.
Temporarily, I currently have 2 routers connected switch wired to asus to linksys with the linksys being connected on the local network of the asus through the cable network. The asus is configured as L2TP that allows the details of user, password & VPN server. Use them in this way gives me the IP addresses associated with the address of the server used. This IP address is provided if connected to a router. Probably not the fastest or the best way but will suffice until I have work on your tech talk. I have an ASUS RT - 68U (which has the VPN Client) available to replace the Asus RT - 56U to come. I can use the 56U on the edge of the property similar to the linksys. Trial & error prototyping will I hope make me it in the absence of knowledge or understanding.
Can someone advise on potential pitfalls with the current configuration or plans for the future?
Thanks again.
-
BlackBerry 10 auto-configuration VPN connection on Wifi networks
Dear all
Soon-to-be owner of a Z10, I try to have a smooth start once it arrives. How would I go about establishing an automatic VPN connection to connect to certain Wifi (public, non-free)? Is it still possible?
The VPN connection offer me free access to these networks, but it is quite annoying to always have to manually open the VPN when one of them is in scope.
Thank you, Florian
Hi floriparate and welcome to the community of BlackBerry Support Forums!
Settings > network connections > Wi - Fi > saved, select the saved network and then add the VPN profile to configure auto-connect when it is connected to this network.
This article will provide more information on the creation of a VPN on your BlackBerry Z10 profile.
KB13469 - setting up a VPN profile on the BlackBerry smartphone
Thank you.
-
ASA5505 for configuration VPN Failover ASA-5510
the best way to configure a second VPN tunnel by another carrier, to fail. The two tunnels would go to the same network a Remote Site. Is it possible to apply a metric or monitor the tunnel so that if the choice we're unavailable two choice would resume. Can you point me to the example configuration preferably with ADSM?
Hi Stewart,
Please visit this link for the same thing:
https://supportforums.Cisco.com/blog/150001
Kind regards
Aditya
Please evaluate the useful messages and mark the correct answers.
Maybe you are looking for
-
The Google web search results 'not fair' in Firefox
I'm having a problem using Google search on the web (toolbar and directly from google.com) in Firefox. When I search a keyword, lets say a company name and you wait to make appear the company Web site, the results include videos, articles, news, etc.
-
Do not want to import images from the photos app
Is it some kind of NOT to have Photos automatically poping upward as soon as I insert a CF of my camera card?
-
Pinnacle PCTV USB2 works do not on A60
I bought an A60-197ITA to use Pinnacle PCTV USB2.My surprise was after the relocation and of the SW that I can listen to the audio but not video.Pinnacle said that the problem is IGP chipset. In particular this of A60 USB 2.0 is not really high speed
-
My printer (Canon MG5250) stopped printing. I can copy and scan.
What happens is... I click to print something from Windows, but what I get out of the computer is the header (which normally gives the time and Page number) and at the bottom of the page I usually get..."file://C:\users\etc. Is there anything you can
-
Vista has a program to backup your files on dvd, but not one of put them back in after you do the system recovery?