Client VPN will travel not connected via 877w

Similar Questions

• Printer will not connect via WIFI

  I'm continually offered an update for my CANON MG3250 printer, I've now had 8 in the past two months, and all were successful. Now my printer doesn't work! that is, it does not connect via WIFI, but will work on cable? All ideas/solutions please.

  Hello Nigel,

  Thank you for your response.

  I'm sorry for the late reply.

  I appreciate your time.

  I suggest you to refer to this article and check.
  Reference:
  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-8&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1

  Please keep us updated.

  Thank you

• Satellite M30-106 - does not connect via radio

  Hello
  hope someone can help im having headache with my Satellite M30-106 problems

  I can connect to the internet via ethernet, but once I delete it does not connect via radio. I am trying to connect to a router broadband Sagem sky but for some reason any he just not going, when I open wireless connections, I can see the projection of router as safe but just cannot connect.

  I would also like to point out I am very new on wireless and to be honest, I don't know what im doing please give me advice in simplistic terms you can so I can be sure I understand where im going wrong

  Regards wayne

  Hello

  If you try to connect to your router, you will ask for a password or what exactly is going on?

  Maybe you should try to update your laptop WLAN driver. You can find it on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online downloads support & -online Download Driver

  Also make sure you use the same WiFi standard that you have configured on the router, for example 802.11 g.

  What operating system do you use? Have you installed all service packs and patches?

• WRT54G v.5 will remain not connected to the new laptop / Windows 7 Premium

  WRT54G v.5 will remain not connected to the new laptop / Windows 7 Premium. It works continuously with a cycle detection, connection, loss of connection; detection, connection, loss of connection, etc... The router works through this cycle, basically acting as if I disconnected and then reconnected to the power to reset, it disrupts my Internet connection to my Wired iMac and wireless, another office to the floor. Paid for Linksys support today and through remote access, he put up a new network on my desktop (iMac). After finishing, the problem still exists. When I told him that the problem had not been corrected, he said just wait an hour or two and it should work itself. She, of course, did not himself. Any ideas out there?

  Nevermind - I seem to have solved the problem with a simple firmware. Funny how the Linksys technician support don't think to ask what version of the router I have or suggest that I should try to upgrade firmware first. However, he is quite good at trying to upsell me for a new router instead of trying to help me solve the problem I had. It makes me want to go buy Netgear next time, thanks a lot!

• B209a-m not connected via USB - but it is! Grrrr

  Hello

  Printer B209a-m shows not connected via USB. This is the case. It was plugged in, installed, uninstalled, reinstalled. All deleted and printers reset, re-installed. It's now showing as a scanner.

  Printer itself says working net connection OK, test page printed OK.

  Site Web of HP software update says "server is not available at this time."

  I'm stuck and pulling hair. Any suggestions?

  Ok

  swear. turn everything off. go and make the tea. Come back half an hour later, everything lights up.

  This works.

• I have an inspiron which will remain not connected to wireless internet but another computer works perfectly

  I have a Dell inspiration that will remain not connected to the internet wireless, but the other computer

  Are the two computers to the same distance from the router?   How many bars do you plan to connect?  You use without wireless - G or wireless-N?  Try clicking on the bars (next to the lower-right clck) then click on Open network and sharing Center, then click on wireless network connection and see that the number of MB/s is just above the bars in the middle of the right.  You should see something like 54 Mbps and at least 2 or 3 bars.

  Good luck.

• Windows Live will remain not connected

  Original title: won't remember

  My account will remain not connected, whenever I go to my email that I resign, even when I check the box to keep me signed.

  Hello

  -What browser are you using to access Windows live?

  -If you use Internet Explorer, then what is the version?

  I suggest you try the following steps if you are using Internet Explorer.

  1. open Internet Explorer, click the Start button. In the search box, and then type Internet Explorerin the list of results, click on Internet Explorer.

  2. press the ALT key then press click on Tools and then click Internet Options.

  3. click on the content tab.

  4. under AutoComplete, and then click settings.

  5 Select or clear checkboxes address bar, Forms, usernames and passwords on formsand ask me before saving passwords .

  6. click OKand then click OK again.

  For more information, visit the below mentioned link:

  http://Windows.Microsoft.com/en-us/Windows7/fill-in-website-forms-and-passwords-automatically

  If the problem persists, I suggest you to ask your question in the windows live forum

  http://windowslivehelp.com/

  Let us know if it helps.

• Guests who will remain not connected to vCenter

  4.1.0 ESXi and vCenter 4.1.0

  We have four hosts in a cluster, two have no problem while the other two will remain not connected to vCenter.  I checked all that in the article 1003409 (http://kb.vmware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1003409) and found no problem.

  Four servers are IBM x 3690 X 5 and all are connected to the same four SAN LUNS, the only difference is that for problem servers management interfaces are on a different subnet, but the port UDP 902 is open between them and the vCenter server.  I can reconnect manually, but they will be disconnected again in a minute or two.

  Does anyone have ideas beyond what is in the article 1003409 that I can check?

  Thank you

  Darryl

  Make sure you have port 902 open TCP , as well as UDP.

  See this article: http://kb.vmware.com/selfservice/documentLinkInt.do?micrositeID=&popup=true&languageId=&externalID=1012382

  Regarding the 902 TCP port:

  vCenter Server system uses to send data to managed hosts. This port should not be blocked by the firewall between the server and the host or between hosts

  If the problem persists, I would try to remove the host to vCenter inventory, add new. Who's going to reinstall agents vCenter on the hosts.

  EDIT: This particular excerpt was taken from the entrance to vCenter 5.x, but the same is true for vCenter 4.x (it is high on the table). To be clear, you 902 TCP and UDP open both vcenter for hosts, host to vCenter and host to host.

• client VPN works do not via 3G

  Hello

  We have a vpn client that works more than wired internet connection, but it does not work via a 3G mobile connection. Please see the enclosed routing table.

  Client: 10.129.42.2/24

  Address public 3G: 10.138.28.162

  Thanks in advance

  Kind regards

  Daniel

  http://www.Cisco.com/en/us/docs/security/vpn_client/cisco_vpn_client/vpn_client5007/release/notes/vpnclient5007.html#wp101224

  Customer Vpn Cisco 5.07 does not support WWAN (also called wireless data cards) devices on Windows 7 (32 bit) x 86 and x 64.

  You use a card 3G speed?

• Printer will not connect via USB

  HP lj1022 printer will not connect not not via the USB port after the installation of the new driver upgrade hp lj1020/1022 for Windows 7 (64-bit). Driver seems to install properly until the moment where he is asked to connect the USB cable. Then he hangs up. HP lj 1020 printer appears in the display to the dashboard as the default printer. Computer recognizes the printer as hp printer lj1022 but in another "device not specified Panel when and only when the printer is on and the USB cable is connected." When printing, nothing ever comes from queue.

  Diagnosis is only that something is stuck in the queue and remove the task from the queue, but does not. Diagnostic shows no problem.

  The lj1022 printer accepts data from two other computers, as well on Windows xP and using the same cables. Three other USB ports have been tested on the new Windows 7 computer without results. The USB ports on the Windows 7 computer accept keyboards, mouse and flash memories wireless dongle without problem. The Windows 7 computer also sends data to a printer wireless with no problems.

  Hi Rmhodgson,

  Run the following utility below.

  http://support.HP.com/us-en/document/c02073861

• OfficeJet 7410 does not connect via WiFi and will not scan

  I don't know if this post is in the right place, but here goes:

  I have a 7410 OfficeJet that was connected to my home network so that I could print/scanning wireless to it from any computer in the House.  It worked well for a while.  I am running Windows XP SP 3.

  We lost power for a few days during the hurricane (Fortunately it was our one central issue), and when the power was restored the 7410 wouldn't connect to the wireless network (we have FiOS).  I checked the unit identifies the correct system ID (and I entered the WEP key), but when I try to install from the desktop computer, it can not find the 7410 (laptop computer also was not able to find the 7410).  The only way I could get the desktop to detect the 7410 is to connect it to the router with an ethernet cable (it does not work with the laptop).  I also can't connect to the wireless printer if I put the IP address in my browser (I'm able to do when it's connected via ethernet).  Not sure if it is a firewall issue.

  When the 7410 is connected to the router with the ethernet cable, I could print to it without any problems.  However, I can't scan from it.  When I try to scan, I get the error message "when trying to scan, could not find the required user interface file (Please reinstall scanning software).  I uninstalled and reinstalled the HP software, but I still get this message.  I also followed the instructions here: http://support.hp.com/us-en/document/c00516936 but that has not solved the problem.

  This morning, I uninstalled the printer with the hope that, put it back in place could solve the problem of scanning, but now the computer is not able to find the printer, even if it is connected by ethernet.

  I hope I gave enough information.  Ideas/comments/suggestions would be appreciated.

  I think I see what's happening. You just need to reestablish the connection to the printer wireless. The document below should help you with that. Once you have done so, the software shouldn't have a problem connecting to the wireless printer.

  Installation of the software of the printer on a wireless network or network (Ethernet) cable

• DSC-HX90V/B does not connect via Wi - Fi for my MacBook Pro under El Capitan!

  I just had a DSC-HX90V/B and got Wi - Fi to connect to my iPhone 6Plus. However, I can't seem to connect to my MacBook Pro using PlayMemories House. I use the network configuration tool, and even if my camera is connected via USB (and why do I have to do this, I could ask?), it is said that "any camera that supports the network connection is connected.

  I don't understand this.

  Hi pws442,

  When you use a Mac OS computer, you will need to download the software of automatically importing wireless to allow the camera send wireless files. You can download the program here.

  After downloading the software, please follow the steps below on how to configure the wireless connection.

  • Initial setup process:
  
  
  • 1. Make sure you that using a memory card is inserted in the device.
    
    
    2. Turn the camera
    
    
    3. On the camera, set the mode of USB connection from the camera to the MTP or PTP.
    
    
    4. Connect the camera to the USB port on the computer.
    
    
    5. On your computer, go to Finder and select Applications.
    
    
    6. Select automatically importing wireless.
    
    
    7. Set up your computer as a device to import files from your camera wireless.

       NOTE: If the device should be synchronized with another computer, the new computer must be defined as import wireless device.

    
    
    8. In the auto import wireless window, select set.
    
    
    9. In this computer will be set to the wireless device for your window of the camera import, click OK.
    
    
    10. Unplug the USB cable to the camera and the computer.
  
  
  • Transfer wireless after the initial setup process
  
  
  • 1. The device, select Menu.
    
    
    2. Select Setup.
    
    
    3. Select settings of the Access Point.
    
    
    4. Select the wireless access point.
    
    
    5. Press the play button on the camera
    
    
    6. Press the Menu key.
    
    
    7. Select send to the computer.
    
    
    8. Follow the instructions to save the images on the computer.

  If my post answered your question, please mark it as "accept as a Solution. Thanks_Mitch

• OfficeJet 7500 a large format does not connect via Timecapsule

  I have a Mac Book Pro running Mac OS X 10.7.5 (just updated all the software).

  I connect my MacBook to the internet through my Apple Time Capsule (wired connection). I use version 6.1 (610-31) Airport utility and I just updated the version of the firmware to 7.6.1

  I use a local wireless through my Time Capsule.

  I just bought a large format HP Officejet 7500 a (model name: C9309A).

  The printer has been set up to detect my wireless LAN and initially he worked for printing and scanning, but it has recently discontinued. I tried to uninstall (purification) the software of my laptop HP, all my software update and reinstall the HP software on my laptop, but it still does not work.

  The printer is connected to my time capsule via an ethernet cable and a USB cable. It also includes Wi - Fi connection generates my time capsule. I have preferthe printer plugged into the router (time capsule) rather than a WiFi connection I print large files.

  I can install the printer on my computer mac laptop (settings/printers & scanners). I added it as a wireless and a wired connection through my time capsule (it shows that the connection is done by the time capsule). However when I print, there is a long delay, the printer now says "printing", but I get the error on my laptop screen "can not write print data: ÿ * xˇ.» A few minutes later a blank page or a page with a single line is ejected from the printer.

  If I go into the configuration of the HP printer, it says I'm under pilot 3.4.1. If I try to open the printer utility I get a message "utility HP does not work with the devices connected to the airport. Try to connect the camera directly to your Mac to work with her. " I tried to connect directly to my Mac via the USB cable and which does not work either. I prefer that the printer is not connected directly to my laptop I have few USB ports.

  In my view, this printer is supposed to be compatible with my system.

  Is there something more, that I can do or this printer is not compatible with my MacBook Pro or my Time Capsule?

  Hi marion_13,

  Turn it on wireless and then try to access the EWS - embedded Web server by typing the IP address of printers in the browser's address bar Safari. I would like to know if you are able to access the built-in Web server?

  Document below will also help you get the printer installed on your wireless computer.

  http://support.HP.com/us-en/document/c02239420

• How can I get the Client VPN or NAT - ted connection

  I installed a router on a customer site to replace a PC that made the NAT on a cable modem connection.

  On the router THAT NAT is done to get all the s PC on the LAN to access the Internet.

  But... one of the users use a VPN client to get to his office. With the PC, there is no problem, but given that the router is in place it can not connect.

  Because I specialized on switched networks my knowledge; edge of NAT and VPN clients.

  Is there anyone who knows how to get this VPN client-session user to be NAT - ted?

  Kind regards

  Martijn Koopsen

  If you have some onfigured of overload, then you tap the traffic. In all cases, you should at least be able to establish a connection, as IPSec uses UDP 500 for the negotiation of the tunnel. If you are not able to pass all traffic, it is another question. Once the tunnel is established, the traffic can be encrypted using the Protocol ESP who cannot be tapped under normal circumstances. If this is a cisco IPsec client, then you must discover which is the feature of termination. If it's a hub 3K, you could activate IPSec over UDP to the problem of circumvention the ESP

  Hope that helps

  Jean Marc

• HP Officejet Pro 8500 has 910 a, Vista 32-bit, does not connect via the usb port on my PC!

  I used to have it all in one connected to my pc, until I lived some printing problems, so I decided to uninstall it!  When I tried to reinstall, the pc will not connect it.  I tried different ports and have replaced the cable, have also downloaded the latest software and drivers all to nothing does not.  I can connect wireless to my laptop, but unfortunately is not a solution for my office because it is not wireless, so it must be connected via USB.  At my wit's end, please help me!

  Hello

  Can you try to insert a flash drive into one of the USB ports on the printer, to make sure she reads it?

  The printer port may be what gives you the question. In addition, you can try the USB printer connected to another PC?

  Let me know the results.