Color LaserJet CP1525 nw: question Laserjet CP1525nw reinstall

Similar Questions

• HP Color LaserJet CP1525nw: Can't get CP1525nw connected to the network wireless Netgear Nighthawk x 6 R8000

  I have never been able to successfully get the printer installed by wi - fi with any stability, so we always connected via USB and shared. I bought a new router and would like to be able to print to this printer wireless anywhere on my network. I can't out of connected mode and mode wi - fi printer. Your software crashes, crash facilities to half way through. The printer indicates an IP 169.254.xxx.xxx, if the network is aware, but it's I can get. None of the HP tools will run under this operating system, they hang immediately upon launch. It's frustration none! Someone out there was a bit of luck with this printer!

  Dell XPS 8700 16 GB of RAM

  Earn 8.1 (64-bit)

  Comcast TG862G Gateway (POS)

  Router wireless Netgear Nighthawk x 6 R8000

  HP LaserJet CP1525nw color printer range

  Hi @jrmunn ,

  I want to help you get the printer works on the wireless network.

  There are a few different ways to install the printer on the wireless network.

  • Thanks to the support WPS.
  • Through the installation, by connecting the USB port, it will configure the wireless.
  • Once the USB installation is done. You can configure the wireless via an Ethernet connection.

  Cycle power to the router.

  First, we must restore the defaults on the printer.

  Press the OK button on the printer, go to the service, and then select restore default settings.

  Print a printer configuration page to make sure that the IP address and SSID are erased.

  Print a Configuration report.

  Uninstall the printer software.

  WPS configuration method:

  To connect your printer to your wireless router wireless using WPS:
  (your router must support WPS)

  Start the mode of the WPS button on your printer.
  Within 2 minutes, press the WPS button on your router.

  Then run a printer from devices and printers Add Wizard.

  The USB method:

  Perform a clean boot on the computer and disable the Antivirus software and any analysis in real-time in the Antivirus software also. How to perform a clean boot in Windows.

  Then run the installation immediately after connecting the USB cable, follow the steps described in this document to update the drivers so that's not new error. A fatal error during Installation of the software. Then the installation should continue. (you can use this procedure for any type of installation)

  If you are still having problems and you have an Ethernet cable, we can install the printer as a USB connection again and then configure the printer via wireless Ethernet.

  Method of Ethernet:

  Restore the default settings of the printer.

  Connect the printer to the router with an Ethernet cable.
  Wait about 1 minute and the printer must have a valid IP address.
  Print the configuration page to get the IP address of the printer.
  Type the IP address in the address bar of Internet Explorer which should open the printer's built-in web services page.
  Installing wireless over here now.
  Click the networking, wireless on the left, fill in information about the network and apply the settings.
  After the confirmation, then disconnect the Ethernet cable.
  Now you should have a flashing light on the printer in 1 minute wireless about.

  Print a printer configuration page, to get the new IPv4 address.

  Then create a new port with the new IPv4 address.

  In the devices window and printers, click right on the printer and on the left, click on printer properties, select the Ports tab.

  Click Add Port, select the Port TCP/IP Standard, then New Port and follow the instructions in the wizard.

• Color laserjet CP1525nw will not print in color

  I installed the PCL6 and PostScript drivers on my Surface Pro 3 to print to my LaserJet CP1525nw color.  The printer is connected to my router.  The printer prints, but only in shades of gray.  What can I do to be able to print in color and continue to print through my router?

  My printer is connected via USB. I installed the full version of the software, and everything works now. Thank you!

• Color LaserJet CP1525nw Printe: CP1525nw transfer cleaning/replacing the belt

  I have a blue streak (3/4 "wide) running down the right side of my impressions. I opened the drawer of the cartridge and looked inside and noticed the same stripe width running down the right side of the transfer belt. Obviously this belt needs a cleaning at least or a replacement at most. My question is: can anyone give me a figure "approximate" on what is a cleaning or a replacement cost? I paid $199 for this printer. The following printer I have in mind will cost me $249. I love the printer I have and I would keep it if it is cost effective to repair. Thanks for your comments.

  You have a bad cyan toner cartridge. Actually remove the cyan toner cartridge and chances are that there will be a bunch of toner on the drum. The transfer belt clean as it moves toward the front of the printer as a broom to windshield wipers that remove excess toner before she put another image to be transferred on paper. Since this is only happening in the one color that tells us the belt is fine and the toner cartridge is the question.

• Color LaserJet CP1525nw: 1 1/2 black lines on the right side and another black spot on the side right laserjet cp1525nw color

  I downloaded the software and latest drivers. It has the latest firmware. I contracted the toner and blown with compressed air. Look in the back for the dust from toner on the sleeve of teflon to fuser. Unplugged, restarted, of course my book has been for laser printers. Ran across several cleaning cycles, recalibrated color, put a piece of paper and toner open door when he was printing. Released A black to see if I could see and toner on blue cylinder. None of the things I've tried have solved the problem. Toner is about 3/4 down. It print fine with this new series of cartridges for quite a while.  I went from my warrarnty.

  .

  The amount of toner from the printer say that there is only an estimate. Your default seems to me that the black toner cartridge is bad. First thing I would do is to replace the black toner cartridge as it should solve your problem.

• Color Laserjet CP1525nw: CP1525nw - wireless set up: 3 networks

  Due to a failure, our cable provider had to replace our modem. We use a router Linksys AC1600 jointly with the modem provided by BrightHouse; We have a hard office connected to the modem and 2 laptops connected wirelessly to the router.

  When the modem has been replaced, the installer created network (1). The Linksys AC1600 has two networks (2) and (5). Our computers are connected to the network (5).

  I tried to connect the printer to the network (5) using the router WPS button and the printer... bad idea. When I used the WPS button, I lost a wireless connectivity to the network (5) and now only a connection to the wireless network (1).

  Found printer Network (2). I discovered that if I changed my computer to the network (2) I can print, however, it's the slower network option.

  How can I tell the printer to connect wirelessly to the network (5)? BrightHouse is not able to help with this issue.

  Thank you.

  Each SSID must have a separate network name.  The 2.4 GHz as TEST and the 5.0 Ghz as TEST50.  It is never the same.  It's how tell you which SSID you are connected to.   If your ISP is a gateway device, you must put it in full bridge mode and turn off the router and just use your Linksys router.

  Only printers support eh networks 2 .4GHz.

• Don't Color LaserJet no power

  Hello

  I have a Color LaserJet CP1525NW and it has no power.  I tried 2 different power cords and nothing... then plug cords of a monitor and they work, so it doesn't seem to be the cord.  I turned the power switch on and off several times, but still nothing.  Does not make a noise.  I don't feel nothing burned and nothing notable prior to this problem.  Any ideas?  Is there a breaker or a way to reset the device?

  Thank you... Jim

  Hey Jim,.

  I see you have a related issue with your Laserjet CP1525nw power.  Looks like you did a large part of the troubleshooting for the device and that the question is internally in the supply circuit of the printer.  Here is the document troubleshooting for the device when a question of power is present.

  The printer will not turn on or respond

  If the steps do not address the issue, so do you know if this printer is still covered by the manufacturer's warranty?

  To check the warranty: http://www.hp.com/go/warrantycheck

  If you need to contact HP Technical Support please use the following link:

  Contact HP worldwide | HP

  Hope this helps,

  Jason

• HP LaserJet CP1525nw color print quality problems

  I got a HP LaserJet CP1525nw color about 2 months ago. After about 4 weeks, I noticed a print quality begins to degrade. Black started first by streaks and fading. Now when blue prints starts to show streaks and melted a magenta pink. All cartridges are at 50 percent of capacity or more. Any ideas about what to check?

  Hello Graf213,

  There are a few things of different which could cause print quality begin to deteriorate on printouts. My guess is that the printer may need to be cleaned and / or calibrated.

  Troubleshooting HP article addresses print quality issues, and provides for the issue of many resolutions.

  Solving print quality problems

  Perform the steps, and I would like to know the results.

• HP Color LaserJet M477fnw MFP: Scan to computer button disappeared

  Hello, I saw similar comments of the same issue, but none with a solution.  The closest is this: http://h30434.www3.hp.com/t5/LaserJet-Printing/How-to-fix-missing-quot-scan-to-computer-quot-touchsc...

  Problem: We have a new printer that we have Setup.  During the installation process, on the touch screen, provided the message to "Scan to Computer".  We used the option to make sure it worked and took part in the computer we wanted.  We restarted the printer, and the option is now missing!  The option "Scan to Computer" has completely disappeared.  Where it was once a touchscreen button / option, no longer exists.

  Printer: HP Color LaserJet M477fnw MFP

  OS: Mac OS X 10.8.xx

  I downloaded the firmware update, but that doesn't work either.  I tried using the verification of updates of the touch screen of the printer, it can never connect.  I connected to the internet, I connected directly on a hard line, still no connection.  I literally just bought this printer yesterday, with a 2-year service plan, drove an hour to the next closest store that had it in stock and it gives me nothing else problems.

  I have unplugged and waited a minute.

  I've uninstalled and reinstalled the printer and the software from my computer.

  I'm out of ideas.

  Hello @gfrd3489

  If you talked about scanning to the icon post from work or option after pressing the icon of the scan on the printer itself that one has been dropped by HP since she had so many questions with that like on some devices will only scan flat and not of ADF.

  If you notice you still have other options such as scanning to USB key, scan to e-mail or scan in network on the printer folder of are next to the HP scanning app on the PC for windows and mac

  Devices most recent are not supposed to have this option on the first place and the firmware and normal updates which will remove devices more alumni who have it

  There were a few M477 which were sold to vendors when it first came out which was which, but as soon as he gets the first update will be deleted

  hope that clarifies the question

• Color Laserjet Pro M452nw: Not accepted print job

  Just installed a new HP Color Laserjet Pro M452nw today, it connects using wireless to my network.  I followed the installation instructions and everything seemed fine and I was able to print the test sheet.  However, when I try to print a document from my MacBook, I get an error message in the print queue, declaring: "Print job not accepted."  I saw the support log, find others with the same question, but maybe on the models of different printers.  In any case, I have followed the instructions for the patch, installed a new printer driver Apple, reinstalled the printer, reset the printing system and I keep having the same problem.  Furthermore, he sometimes interrupts the print queue after encountering the error.  Do not know what to do...

  Hello @sanovogo

  You can try the following changes

  Go to the network set up on the printer and network services, disable ipv6 (disable)

  Go to the link (always within the network set up the menu) speed and the complete change to 100TX

  Sent a new print job to the unit

  If it fails while you see the error on the PC to the printer and try to deal with a report of configuration in the menu reports

  Get the IP address on the right side on the 1st page under settings of the printer

  Enter the IP address in the URL of web browsers, this online application should open indicating the status of the printer in this way can isolate you the connectivity to the printer

  If by this desire to point showing the error on the PC, you can print the configuration report and Web site opening, I'll suggest another pilot, because it must be the one having the problem I could give other recommendations but will like to know what happened first

• Printer driver LaserJet CP1525nw moved

  All of a sudden my Laserjet CP1525nw color printerdriver reinstall on a USB cable. Technical support is unable to find the problem. I also cleaned my registry and my hard drive but nothing helped. I rarely meet driver problems and have never had a printer driver install fail. Can anyone provide any indication this problem?

  I'm under Win. 7 (32-bit) on a desktop computer.

  Hi Ron,

  You are right, it would be something in the operating system at the origin of the problem. Unfortunately I can't help you with issues related to your operating system. The only thing I can say is that you back up your data on the hard drive and then reload your OS. I'm glad to hear that you were able to successfully install the printer on your computer and the other computer. Have a wonderful weekend.

• Color LaserJet MFP M477fdn Pro: M477 Software Installation fails at 99%

  Like others who have posted here, I have been unable to get the printer software to complete the installation. The printer is a Color LaserJet Pro MFP M477fdn, 3 months. I'm trying to install the software on a new workstation HP Z240 performing Windows 10 (64-bit). The connection is via USB cable. The printer and the software have been previously used with a Windows 7 machine without problem.

  I tried, repeatedly, to install the software from the disc supplied with the printer and also a 126.6 mb download HP Color LaserJet MFP printer M477 Pro series full software and drivers. The results are the same with a source - installation apparently progresses up to connect it the indicator product of progression from screen reached 99%, how it gives an error message "a Setup operation took too long to run. It is a fatal error, preventing the use of the product. Restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. "It takes about 20 minutes for the phase of installation to go from 0 to 99%, and then later hooked up to 99% for 2-5 minutes, the error message is displayed.

  I am able to print to this printer, but at least do not have the ability to scan from the computer there is no indication that the I.R.I.S. OCR software is installed.

  I had care of do not connect USB until you are educated.

  I tried repeating the installation without uninstalling first and get the same result.

  I used the uninstall contained the disk feature, and have deleted the printer to the computer using the Panel between the installation attempts.

  I tried to do a right click to run the installer as administrator and get the same result.

  I tried to install after clean boots with turned off Windows Firewall and all functions of the software Norton Internet Security including its function of firewall turned off.

  The event viewer displays none error entry at all and no entry identifies HP as the source of an event.

  I tried to connect via USB 2.0 and 3.0 ports.

  I cleaned recycle them and temporary folders.

  I have updated the firmware of the printer to the 20160331 version.

  Printed printer configuration report will not display any errors, nor that the printer itself indicates something is wrong and confirms the update of the firmware.

  I deselected the optional software, the devices experience HP and I.R.I.S. OCR, trying to install only the required files two more program scanning HP.

  Thanks for any help solving this.

  I think I understood the question, 10 windows installs its own driver, and the installation program expects the hp driver to install.

  DO this FOR THE HP INSTALLER PROCESS (when the percentage meter goes)

  1. go into the Device Manager and find the printer in the list of devices

  2. right click on the printer and select "Update Driver software"

  3. click on "Browse my computer for driver software".

  4. choose "Let Me pick one...» »

  5. Select the named driver: HP Color LaserJet MFP M477 PCL-6 Pro (make sure it's one with a dash between the pcl and 6!)

  6. click next and back to the installation of hp box and must now see the printer and continue the installation.

  -Alex

• Color LaserJet MFP M177fw Pro: installation of web services blocked to 'connection '.

  I'm trying to enable Web Services on this new LaserJet.  I am in the built-in Web Server page and the configuration of Web Services tab.  I clicked on 'Turn on' and it just keeps spinning in connection...

  DNS is 8888 and 8844

  All the other tabs work; It is connected to the computer and the Internet.  Help please?

  Thank you!

  Hi @crowndude,

  I see that you have problems with Web Services. I want to help you.

  I have provided a few steps to try to see if we can solve this problem.

  Turn off IPv6 on the printer.

  Go to configuration, network configuration, network, IPv6 Services and turn it off.

  This DNS works better for Laserjet printers. Please change the settings to see if this will help the printer built-in Web server.

  Preferred DNS address: 209.244.0.3
  Auxiliary DNS address: 209.244.0.4

  Power cycle the printer.

  If you still have questions, please continue with the following steps:

  Update the firmware of the printer by a USB connection. HP Color LaserJet Pro MFP Firmware update M177fw.

  Configure a static IP address for the printer. Proceed to Solution 3: printer of the assign a static IP address.

  Printer HP Color LaserJet Pro MFP M177fw and HP LaserJet Pro MFP M127fw and M128fw printers - printer does not keep the Wi - Fi connection.

  I'll send you another step to try in a private message.
  In the forum next to your handle name simply click on the envelope to see.

  If you appreciate my efforts, please click on the "Thumbs up" button below.

  If there is anything else I can help you, let me know. Thank you.

• Impossible to activate the services web ePrint for Color LaserJet M551

  Hello

  I read all the posts in this forum about the web services enabling ePrint to the question and tried all suggestions with no luck.

  Here's the situation:

  1. The printer works fine on place. I can print without problem.
  2. The printer is connected.
  3. All my router ports are open for outbound connections, including UDP.
  4. Communication using log in my router I can see that the printer can resolve DNS names using either my ISP DNS server or the suggested 8.8.8.8 and 8.8.4.4. Using nslookup shows ' registration-pro - site1print.houston.hp.com "Decides to 15.240.60.111 and" registration-pro - site2print.houston.hp.com "Decides to 15.201.224.79.
     This indicates that the printer can indeed resolve the addresses. Newspapers also Awakenings that the printer communicates with the servers (connection is established and data transferred) via https (probably the web service), but always after a few minutes the clearance process is to expire.
  5. I tried this allowing the procedure since a few days my believe that the recording servers should have worked some time during this period.
  6. I'm frustrated
  7. .. .even more frustrated
  8. what I am doing wrong?
  9. Help, please!

  trying to install eprint for my new M551dn Color LaserJet and it fails with the

  Who out there having the same problem I had. HP could not help me I restore to factory settings and reconfigured everything and all of a sudden the printer managed to enable web services and print the print code.

  Good luck to you face the same problem!

  / MrQQ

• HP Color Laserjet CP2025 print: color printing problem

  Had the printer listed above for several years and love it.  Have just started having problems with the printer does not print not not in color.  Have a recorded document that needs to be printed every month and have had no problems with it, until yesterday when it is printed in black only.  Another document word also printed in black only.  I printed a test page printed correctly.

  Don't know if there is a definition in the document, or is it a printer problem.  Help!

  Welcome to the community @mwillis HP

  I came across your post about the color printing problem and wanted to answer to help with my suggestions. Please see the guide below to resolve this issue.

  HP Color LaserJet - cannot print in color or impossible to Auto-Duplex (two-sided printing fails) after the installation of the UPD

  Let me know if you have any questions.

  Hit the "accept as Solution" if we reached a solution and the "thumbs up" to say thank you for my help.