color problem whit hp 4500 printer printing

Similar Questions

• HP C5180: Printer color problems

  I have a HP C5180 printer and printing color is messed up. My black watch diagnosis page than black, yellow-green with yellow strips, Lt Cyan shows as a dark cyan, cyan is white, Lt Magenta is dark blue, Magenta is Lt. blue. Anyone know how to fix this... I changed the printer cartirdges... the same problem. I cleaned the print heads. several times and followed the suggestions on the tech support pages. I would not only use this printer as a black and white printer.

  Hey @TomTwist,

  Welcome to the Forums of HP Support!

  I would like to help you today to solve print quality problems you are having with your HP Photosmart C5180 all-in-One Printer. Because you have already replaced the ink cartridges and clean the printhead several times nothing is done, there is a good chance to have a defective print head. The print head is what reads the cartridge and puts ink on the page. On your print head template system is a non-replaceable part. Therefore, should that do not pass part a replacement of the entire unit would be necessary. However, I would like to go through the following steps to conveniently solve this problem of quality.

  I won't make you run any printhead more clean. The rule is usually 2 or 3 clean makes no difference at all, don't make a fourth because when you clean the printhead system it uses ink in order to rinse the ink system. If 2 or 3 clean make no difference that you're just wasting if you run a clean more.

  Step 1: Calibrate the colors:

  1. open the printer Toolbox: HP Solution Center. This should be on the desktop of your computer.

  2. If you have more than one printer installed, be sure to select the correct printer tab in the HP Solution Center

  3. click on settings

  4. click on print settings.

  5. click on printer Toolbox.

  6. on the device Services tab, click color to calibrate, and then follow the instructions on the screen. The procedure takes about two minutes and requires two sheets of paper.

  Source: The printed colors are not colors should

  If the problem persists, please continue to the next step.

  Step 2: Align the print head:

  1. click on HP Solution Center's on your desktop

  2. click on settings.

  3. click on print settings

  4. click on printer Toolbox.

  5. on the tab Services of device the printer, Toolbox, click align the print cartridges, and then follow the instructions on the screen.

  Source: Streaks or lines in the printed Image

  Please test print once these two steps have been taken. If the issue of quality still persists, because you have already replaced your cartridges the next step would be a replacement of the entire unit.

  If you want to explore additional options available for your printer, I suggest you contact the Technical Support queue by phone.

  HP Technical Support can be reached at the: 1800-474-6836.

  If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  Worldwide contact HP

  Good luck!

• HP Envy 4500: HP Envy 4500 printer problem

  I have a HP Envy 4500 printer which has worked very well for a while. Recently I converted to NBN with a new router and well that the laptop has had no problem with the printer connectitivity. The printer works fine for about 10 days, then do not print. When I use the doctor of printing & scanning HP he passes through the "fix" and finally confirmed that it will be printed internally, but must be uninstalled and installed again. I did it and it installs ok then, (I use the download to be installed on the HP site) and it prints ok again for a while.

  I use the wifi for the laptop and the printer, and even still have the printer close to the router, the printer will print after 10 days. The printer wifi appears connected correctly.

  Why it works for ten days and then do not print unless I uninstall the printer and reinstall?

  Hello

  Thank you for using the forum.

  Have you tried to see if the IP address of the printer has changed whenyou can not print?

  You go to the front panel and press the 'Wireless', and it will display the IP address.

  Now go to the PC > start > all programs (or all apps to win 10) > HP > HP4500 > IP update

  Run small applications and compare if the IP address on your printer software is the same as on the printer.

  If this isn't the case, it is the reason why it can not print!

  Look at this video, he shows how to create a static IP address, there is a part of the video at the end that uses the "update IP address" address verification tool that has been described above.

  Creating a static IP address by using EWS

  https://goo.GL/m4hexn

  Update the IP address is at 01:41

  You may consider to change the address of your printer to Static if it is what the cause of your problem.

  Let us know.

  Thank you.

  Please click on "Bravo Thumbs up" as an encouragement and "Accept as solution" if it helped to solve your problem.

• using the color laserjet 3600n - I want to print in black and white, but it prints black and white negative. * beep *.

  using the color laserjet 3600n - I want to print in black and white, but it prints black and white negative.  * beep *.

  I was able to recreate what you see.   I managed to work around it by installing a different driver that is also supposed to be compatible with the CLJ3600.

  Please consider trying this as a possible solution:

  (1) uninstall the driver CLJ3600 by opening printers and fax machines, driver selection and right-click on it and select Delete.  Once it is removed, right-click on an empty space in the windows printers and faxes and select Server properties.  Click the driver tab, click the CLJ3600 and then click on remove.

  One when you're done, restart, and then install the CLJ3500 driver.  This is a previous version of the driver that has been implemented for the CLJ3600 and is compatible with the CLJ3600.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesId=315862&prodNameId=315867&swEnvOID=228&swLang=8&mode=2&TaskID=135&swItem=LJ-16838-3

  After installation, try printing again.

  The output I have indicates it will print is more negative.  Please let me know if you have success.

  One caveat about this solution.  The Color LaserJet 3500 doesn't support duplex.  Of workaround only works for two printing on the package of basic or the Color LaserJet 3600 N.

• Hi, I have a Canon iX6850 printer, but I can't print in color from photoshop. The prints are black and white? What should I do?

  Hi, I have a Canon iX6850 printer, but I can't print in color from photoshop. The prints are black and white? What should I do?

  Hi Vera,

  Thanks for the update.

  Make sure that the image is set to RGB in Photoshop.

  In addition, we suggest you follow the steps below:

  1. exit and then restart Photoshop

  2. go in the file menu > hover your mouse over Print > press and hold the space key

  3 try printing

  This would reset the printing preferences for Photoshop.

  Kind regards

  Claes

• HP Officejet 4500 printer problems

  I just installed a HP Officejet 4500 printer and I have lost any link help me plesae usb ports because HP could not?

  Hello

  Make sure you have the latest vista drivers for your computer which you can get your computer manufacturers Web site

  go to their website and look for a driver and software download section

  Enter your model number for the last look drivers vista then download and install

• My HP Officejet 4500 printer install problem

  My HP Officejet 4500 printer keep installation on HP Pavilion dv6 workstation even if it is already installed all day

  The installation process is probably a failure at one point causing an incomplete installation. Have you tried to do a complete uninstall and reinstall process? If you have any software virus protection try disabling the installation just to limit background probably interfere the installation process applications.

• Want 4500: Print missing the top of the document

  Hello

  Here is the problem that I am facing. I have a document Word 2013 which is the A4 format. When I print the document on plain white paper it prints without a problem. However, when I print on paper (120 g/m²) Brown Buffalo output a mixed success.

  Sometimes, the impression is correct - yay

  Sometimes feel like missing the beginning of the document. In that the output will print the bottom half of the paper half top of paper. In addition, the amount of printing which is not respected by the top of the page is also intermittent. Sometimes it's a couple of cms, sometimes its a half page.

  My document is in the landscape. The document has no margins, but there is no printable data less than 10mm of the edge of the document.

  As printing is correct with the white paper and defective with the brown card, I can only assume the problem with the printer paper type and not the document or the configuration of handling.

  Any help much appreciated.

  Yes, understand you it correctly. The problem is the document management capabilities of the printer. According to the specifications of the HP Envy 4500, Max paper weight it can handle is 120 g/m². If you are using their HP Premium presentation paper, you can get better results. However, if you decide to continue using brown paper you have there, there a trick so that you can get better results.

• White background, gray printing

  Hello

  I use CS 5.5 on a mac

  Somehow, today, I managed to change the color profiles and I can't understand how to reset the. I don't usually adjust these profiles, but today I got the impression problems with an HP printer and I adjusted the. It made the problem much worse!

  
  

  When I print, white print gray. If I close and open the document, it does not say synchronized. I went to the bridge and Choose a single color profile but it does not appear to have made much difference.

  How can I get the settings back to the way they were originally? !!

  I use Indesign to novice, but I rarely look under the hood!

  Thanks for your help.

  

• Parts white fonts when printing / export but not visible in Photoshop

  Hello

  I work on our wedding invitations and ran into a few misprints.

  Everything looks OK in Photoshop (CMYK, color presets used from the print service, etc.) but once exported in PDF format / or printed, the 'partially white police' - problem occurs. (see attached screenshot)

  It is therefore all two visible in the exported PDF document or printed (directly from Photoshop).

  I first thought that it had something to do with the police (Angelina), but occurs with other policies as well. I noticed when you select some text in Photoshop, the 'white' pieces are parts of fonts that are outside of the selected text (whereas in fact text is selected, ready for editing). So it is perhaps a clue...

  If I reduce the font size to more than half the size, the question is no longer there.

  

  Move it to the top most layer and try again... or send me the file... easier...

  G

• 4500 envy: Envy 4500 printer not

  So my Envy 4500 printer worked very well on the network for more than a year, but last week we had our wifi router change and since it does not print. Well, it prints, but you must put the printer off, then put it back and it will print only the first document in the queue (it will not print, you must do the same thing) I tried to make my pc and it says that "a document in the queue block printing" or something like that and it removes the document but if you try to reprint it does the same thing thing. It's really annoying to toggle the printer for each document... Thank you

  Hello
  
  Thank you for using the forum. You can try the following:
  
  Please download and run the HP Print and Scan Doctor (PSDR) tool to diagnose and solve your problem
  
  http://h20180.www2.HP.com/apps/NAV?h_pagetype=s-926 & h_lang = on & h_client = s-h-E016-1 & h_keyword = DG - PDU
  
  Hope that helps.

• HP Envy 4500: Print jobs disappear from the print queue and not print (Windows 7).

  I just bought a HP Envy 4500 printer,

  When you attempt to print from a PC with windows 7 OS home pro (64-bit), the print job appears in the queue and then disappears, but the printer does not print anything.

  Everything else seems to work very well know

  • The printer prints the internal test page
  • The printer does print when you use iPad2
  • The printer does print when you use ePrint
  • The PC recognizes and communicates with the printer (tried with USB connections and wireless)
  • Analysis feature works very well - when initiated from the PC and printer

  I tried

  • uninstalling and reinstalling the software (several times using software from different sources)
  • restart the printer queue service
  • Disabling the firewall
  • running printing HP and doctor Scan
  • following the instructions described here (the question is the same but the different operating system):

  Print jobs disappear from the print queue and print (Windows 8)

  • combinations of all of the above

  Absolutely no joy in any of them, and in spite of more than 2 hours of research on Google and forums search I can't find a solution.

  HP... can you give me a solution or is that goes back to the shop?

  Well I finally worked on the fix myself by trial and error.  I changed the security settings for 'All' and 'Creator owner' to 'Print' and "Administer Documents".  Why on earth they were not automatically allowed as part of the installation, I couldn't really say.

  Hope this helps someone else with a similar problem.

• Want 4500: HP Envy 4500 print in word or complete print jobs. With the help of Windows 8.1

  I recently purcahsed the 4500 envy. I'm having problems with it not printing from word or any work was finished on 2 pages.

  I uninstalled it, reinstalled, download and run the print doctor and everything is fine and downloaded all the drivers. I use an HP laptop and the Windows 8.1 operating system.

  Help, please!

  Thank you.

  See if this hotfix Microsoft help.

• DeskJet F4280: White stripes (no printing) - F4280

  Horizontal white stripes (no printing) - seem to be in the same location on the page when they occur.  'Only' occur when printing from a Microsoft Works word document or spreadsheet, or copy a page perfectly printed.  Test the printer Windows page ok being IRS forms and instructions were published recently.

  @PapaPhil,

  Welcome to the HP community! I wanted to stop to my suggestions to help with your problems. If I understand the questions, print outs of Microsoft Works and when making the copies of your Deskjet F4280 all come out with horizontal white bands on them...

  As copies are a feature that doesn't involve all the computer, it is a sign of a hardware problem. You can try a power reset (see below) and to ensure that the printer is connected directly to a wall outlet, avoiding the power and surge arresters bars.

  Try to make a copy again from the front of the printer and if the horizontal bands to continue, you will need a new unit and I would say to contact HP to see on your next printer options.

  If you find that copies work fine, please let me know and we can move on to troubleshooting software because it will show us that the printer itself is OK!

  Click on the thumb to below testify my help!
  Click on the "accept as Solution" if I'm you guide to a solution!

  Good luck!

• HP Envy 4500: Printing on Photo Premium Plus paper on Envy 4500

  Bought the new Photo Premium Plus paper and I am so frusterated I try to print on this subject!

  I get all the rear bars, especially on the back or cut the wide 1/4 of the image.

  Any suggestions?

  @Nadine63,

  Thanks for getting back to me. After taking a quick glance in the Specifications of the printer under the tray capacity paper, the maximum weight is listed as up to 281gms (75 lb). The one you use is heavier (80 lb) that is why you see the question.

  Let update you the software and drivers to make them compatible with your operating system Windows 10. Please follow the steps listed below:

  Please, try disabling your firewall and perform a clean boot. Now, follow the steps below:

  1. disconnect the USB key if you use a direct connection.

  2. remove the software HP Envy 4500 to uninstall from the control panel of your computers an option of the program.

  3. restart the computer.

  4. make sure that all the software 4500 envy has disappeared from the list of programs, but also your HP folder listed under all programs in your Start Menu.

  5. now, go ahead and download the software and drivers for your desire to 4500 (DO NOT connect USB until the software prompts you to):

  HP ENVY 4500 e-all-in-One Printer series full feature software and drivers

  6. go ahead and print a test page.

  7. If you are unable to print a test page, run the HP print and scan doctor > www.hp.com/go/tools

  -It has been designed by HP users troubleshooting and problems characteristic needed to solve many common problems encountered with HP print and scan products related to Windows computers.

  You can try to start the photo, but I suggest to change the paper first. Please let me know if it was successful!

  Thank you for being a part of the community of HP. Please let me know if this helps solve the problem by marking this message as "accept as Solution" . If you need more assistance let me know and I will gladly do whatever I can to help. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.