Comments of Jabber with VCS registered endpoint control and MCU

Similar Questions

• Cisco Jabber with VCS

  Hello

  I VCSC and TMS in the network, there are of the endpoints configured with SIP and H323. VCSC are not in the field.

  Now we have to enter Cisco Jabber with the VCSC. What are prerequisites them?

  First it requires license for Cisco Jabber on VCSC?

  We need to join the VCSC domain?

  Our VCSC is version 6.1 and TMS is 13.

  TNX

  Bobby

  Yes, you will still be able to authenticate users JabberVideo locally, 'right', you won't be able to use NTLM.

  Also take a look at the TMS Provisioning Deployment Guide:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/TMS/config_guide/Cisco_TMS_Provisioning_Deployment_Guide_13-0.PDF

  /Jens

• With the help of control and simulation module; e to get the time the MISO model Manager

  Hello

  Please can someone show me how to find the response time of the system below using the module control and simulation?

  (y (k) - 1,7407 y (k-1) + 0.6236y (k-2) + 0.1782y (k-3)) =-0.0932 u(k-1) + e (k)

  where there is out, u came and e is a white noise.

  I tried to enter the CD construct MIMO model, then connect it to CD response time. * s vi.

  But what I really need to enter the model coeffs every time? and I still don't see the answer!

  Help, please...

  Kind regards

  ruser

  Hello

  you have the correct image... I used the Toolbox ID sys (Assistant)... to estimate the system model...

  and I tried all week last get the model of my system in labview for use the control on this module.

  Alhamdulillah...

  I ended up doing... I saved the template to a file from the Toolbox id sys... (my model is in discrete form) then I loaded it in labview using load file pattern...

  so now I in labview...

  now for control parts... ..

  Thank you again...

  ruser.

• Need help with my Toshiba remote control and receiver for Qosmio G30 161

  Hi all

  I have a Toshiba Qosmio G30-161 and with her, I have a Toshiba remote and a Toshiba remote control receiver, this is the first time that I used it (tried of that is), my problem is that the remote control does not work on the computer, when I press keys on the computer program does nothing.

  I installed four new AA batteries and the remote works fine its send signals to the receiver, the receiver of the remote control as a red light detection is displayed whenever you press a button and with regard to the computer, I checked the drivers and the USB is off the hook as a remote E-reception receiver which I checked with Toshiba and which is correct , so overall the remote control works, the receiver is picking up signals and the pc has detected the receiver but nothing works, I have installed remote control manager but was still nothing done to. I talked about support and assistance of Toshiba, and the end result is that they are not sure what is the problem. Can anyone help I need the remote control for the slide shows for clients like ja? m a photographer.

  Also to confirm that I'm under addition of Windows XP MCE.

  Anthony Worlock

  Hello

  This remote will work, if you use it without any special drivers and special software, only in the Media Center.

  But if you install stuff like [WinLirc | winlirc.sourceforge .net] then you should be able to get some functions for your presentation.

  Please try this tool and check if it works.

  By the way: if I were you I would first read the manual and the WinLirc FAQ before you start because it s a little bit tricky to manage the program. :) (Too many parameters: D)

  Welcome them

• Problems with delays of parental control and activity reports in Windows 8 PC

  The family safety team has identified two problems for people using parental controls in Windows 8:

  ·         Time stop working

  or

  ·         Parents receive reports of activities that have no PC activity, even if children are using the PC. (Use and web application use is still reported, but the chart for PC time used is empty.)

  I had the same problem (s).

  Finally fixed it.

  The child user account must have the PC 'trust' in relation to the windows live account online restored. Connect you to the computer with the user account does not. By scanning or the mouse, click on the right side.

  'Settings', "Change PC settings" "sync settings" "passwords" "trust this PC.

  You will need to have a code sent to your mobile phone or the phone at home or email.

  Once the code is entered and verified, the PC is now in 'Trusted PC (s)' account online windows live.

  This must be done on each user and each PC that does not work.

  Good luck, hope this helps other parents. I was pulling my hair out with this not working do not. Time limits is the best thing in the WORLD, as long as it works!

  Sorry kids, no more free time on my watch!

• Conflicts with HTML-based CFGRID controls and prototype

  Someone had problems with the help of the CFGRID based on HTML in a page using Prototype.js? We are currently using the prototype library for the manipulation of some of our functions of banner on our pages, but when I use the cfgrid html-based data is displayed if you click on a column header. On load/refresh the page, without rows of data are displayed. I think it may be related to refresh in contradictory cfgrid with a prototype, but I'm only guessing. If I remove the Prototype include file from the page, and then run the cfgrid normally controls screens. Any ideas?

  You can post your bug here,

  http://www.Adobe.com/cfusion/mmForm/index.cfm?name=wishform

• A button to push on CUCM registered endpoints

  Hi all!

  I tried to implement a buton to push with CUCM registered endpoints. As far as I understand it, the system must be added to the MSDS directly and not only as the room, therefore RSI can push messages to the endpoint. If I add endpoint to TMS I get error, that endpoint has put the wrong type of provisioning. Accordingly, I am not able to change the settings of reservation, as allow remote booking for MS Exchange integration.

  BBFRR may be available for endpoints registered or is - CUCM this only available for registered endpoints VCS?

  BTW: versions:

  TMS 14.3.1

  TMSXE 3.1.2

  9.1 2 CUCM

  Conductor X2.2

  TS3.1

  Kind regards
  Paul

  [...] If I add the endpoint to TMS I get the error, that the endpoint has set the wrong provisioning type. [...]
  
  

  Hello

  Did you add endpoints to TMS the correct way, i.e. "to list" > "Unified CM?

  Kind regards

  Kjetil

• best way to control a large number of controls and indicators

  IM building a façade with 46 orders and lights, all of type boolean.

  the logic is control > send order series > receive > indicator set. I consider part of my façade (with 2 sets of control and indicator) and my block diagram.

  I have to be able to control programmatically and through the front panel individually the status and indicators, or all at once (for example to reset the both). This should be done from the tab they are and another.

  thought property nodes but still I would have 46 + 46 of them. same for local variables.

  y at - there I way to refer to a control/indicator by its label (string) and change its value?

  wouldn't be easier just to create two Boolean tables which maintain their Boolean value?

  Please advise me on what options I have. I'm new to labview.

  Thanks in advance.

  
  

• GW ISDN Cisco with VCS control

  Hi Experts,

  I'm new with Cisco ISDN Gateway 3200, and I will integrate to the existing video network managed by VCS control with the endpoints and MCUS registered as SIP.

  Here is an example of the existing video network numbering plan:

  SIP URI endpoint: [email protected] / * /

  MCU SIP URI: [email protected] / * /

  ISDN GW H323 alias: 54xxxxx

  I came up with these questions:

  1. for us intergate ISDN GW on the video network, we must save as H323 on the right VCS?

  2. to call scenario as a point endpoint SIP or MCU calling to one ISDN endpoint via video, how the call flow? Make the registered endpoint/MCU SIP point as SIP on the VCS can dial directly on this endpoint ISDN? Or they will call first the H323 number of ISDN GW recorded on the VCS then routed to an auto attendant of the ISDN GW?

  3. How about ISDN endpoint SIP endpoint?

  Please send me a sample of guide and the configuration of the ISDN GW and VCS about how we could improve the flow of calls work on the call scenarios mentioned.

  SIP---> ISDN

  ISDN---> SIP

  Thank you very much for the help.

  Best regards

  Acevirgil

  Hello

  1. For us to intergate the ISDN GW on the video network, we need to register it as H323 on the VCS right?
  

  Yes, it's true. This isn't the only method, but it is the most used and most easy way. I suggest you use it.

  2. For call scenario like from a SIP endpoint or MCU calling an ISDN endpoint via video, how's the call flow? Do the SIP endpoint/MCU registered as SIP on the VCS can dial directly on that ISDN endpoint? Or they will dial first the H323 number of the ISDN GW registered on the VCS then routed to an auto attendant of the ISDN GW?
  

  In this case, you will need to ensure interoperability the call in VCS. No matter what SIP endpoint can dial numbers ISDN, and then VCS will route the call to the gateway h323 format, only the number with any ' @domain.com ' and the call will be interoperability. The flow would be something like this:

  Point endpoint [sip] SIP----> - VCS [H323]---> Gateway ISDN

  3. How about from ISDN endpoint to SIP endpoint?
  

  The same concept is applied. ISDN gateway sends the call in H323 for VCS and interwoks VCS the call and sending SIP endpoint. Something like this:

  SIP endpoint<-------[sip]--------- vcs=""><--------[H323]---------- gateway="">

  With regard to incoming calls from gateway ISDN to VCS, there is one important thing to consider. You basically have to methods:

  • You can configure the ISDN gateway to route calls to the auto attendant, then users will be able to recompose the verse numbers of internal endpoint for the auto attendant
  • You can configure the ISDN gateway to use DID (Direct inward dialing), in this case, you create routes to the gateway which maps each ISDN number to an internal endpoint registered to the SCV

  Both methods work fine, however, when using auto attendant, it is very important to implement a scheme of toll-free fraud prevention. Take a look at this thread:

  https://supportforums.Cisco.com/message/3971947#3971947

  Regarding the guide, it is not a simple step by step explaining, but the Administrator's guide provides a good explanation on how to configure the dial plan in the gateway and how to enter the doors of VCS. Check out this guide:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/isdn_gw/admin_guide/isdn_gateway_printable_help_2-2.PDF

  I hope this helps.

  Concerning

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• MX200 (TC6.2) cannot save with SIP TLS for control of VCS

  Hi all

  I just got a brand-new MX200 in our laboratories.

  We will evaluate at the moment the overall upgrade to the version sw TC6.2.

  The MX200 was delivered with TC6.1.1.7. Check in the control of VCS with SIP TLS works without any problem at all.

  VCS - C eventlog:

  "26 aout 14:16: 47 tvcs: event ="Accepted for registration"Service ="SIP"Src - ip ="172.18.93.88"Src-port ="5061"Protocol ="TLS"AOR ="[email protected] / * /"Contact =" sip:[email protected]/ * /: 5061; transport\ = tls"duration ="60"Level = '1' elements UTCTime = '2013-08-26 14:16:47, 833'

  "26 aout 14:16: 47 tvcs: event ="The requested record"Service ="SIP"Src - ip ="172.18.93.88"Src-port ="5061"Protocol ="TLS"AOR ="[email protected] / * /"Contact =" sip:[email protected]/ * /: 5061; transport\ = tls"duration ="60"Level = '1' elements UTCTime = '2013-08-26 14:16:47, 831'

  After registration TC6.2 update fails.

  The 26 aout 14:36: 26 tvcs: event = "Rejected registration" reason = "Received no authenticated source" Service = "SIP" Src - ip = "172.18.93.88" Src-port = "36545" Protocol = "TLS" AOR = "sip:DOMAIN.com" Contact ="<>[email protected]"/ * /: 5061;transport\=tls>;+sip.instance\= '"" duration = '3600' level = '1' elements UTCTime = "2013-08-26 14:36:26, 481"

  26 aout 14:36: 26 tvcs: event = "The requested record" Service = "SIP" Src - ip = "172.18.93.88" Src-port = "36545" Protocol = "TLS" AOR = "sip:DOMAIN.com" Contact ="<>[email protected]"/ * /: 5061;transport\=tls>;+sip.instance\= '"" duration = '3600' level = '1' elements UTCTime = "2013-08-26 14:36:26, 481"

  As far as I can see there's something doesn't quite work with the protocoll in relationship with the SIP URI (AOR). Miss me the prefix "[email protected] / * /"

  All other systems (profile, ex, sx) work properly with TC6.2.

  Anyone have an idea?

  Hi adil,.

  Since the inscription "AOR" is only said AOR = "sip:DOMAIN.com"

  I belive you must have some sort of rule research on the VCS the sip domain and pointing to the crossing or a nearby area and the policy setting must be "audit powers.

  and since there is no name of user and password available the record attempts will fail with the message "from source" unauthenticated

  did you recently create transformations on the VCS? also, check your configuration of endpoint.

  You can create a rule to send this registration through local area message passing in turn to the subzone to registration. Please note the subfield must be set on "treat as authenticated" If you do not use authentication.

  Rgds

  Alok

• Integration: Jabber with VCSC

  Hi experts,

  I'm new in the world of telepresence and I will install into a new customer a solution with VCSC, TMS and MCU.

  The customer already has a CUCM with Jabber and they want to deploy the Jabber with VCSC, they want that, for example, a Manager actually a video conference with other offices through your Ipad with Jabber

  I have not found a document with this configuration, can someone help me with the documentation of this integration?

  With their experience of telepresence, including the complexity of this integration? Can give me of highlights and key points of this integration?

  Best regards

  In addition to what Alok suggested, there are other things, you should consider:

  • The version of the recommended software is CallManager 8.6.2 and later (you can try 8.5.1, but there is no support BFCP)
  • It must integrate CallManager and VCS by following this document:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/VCs/config_guide/Cisco_VCS_Cisco_Unified_Communications_Manager_Deployment_Guide_CUCM_8_9_and_X7-2.PDF

  • To enable content sharing between registered in CUCM Jabber and the end point registered in VCS, make sure that your Jabber in CUCM devices have a SIP profile with BFCP protocol enabled, as well as the setting "Allow presentation sharing via BFCP" set to allow.
  • If you want to schedule conferences in MSDS for the Jabber in CUCM, you can add them to TMS as a 'room '. By using this option, you will be able to plan the Conference and the calendar control (it's better than using the Participant model)
  • About the phone book, you might have some problems. If your devices registered in VCS use device with an alphanumeric URI address, for example [email protected] / * /, you will not be able to add this contact to Jabber clients registered with CUCM, alphanumeric once is not supported. A solution would use only digital device address for all devices. About Jabber for Telepresence, you can define directories using TMS, in this case, you can add contacts without problem, either using a digital or non-digital address.
  • If you have endpoints another enrolled in CUCM who will call the end points registered in VCS, make sure your devices are running compatible software versions, mainly the videophones. It is strongly recommended to use the latest version of the software.
  • Be aware that Jabber for Telepresence doesn't support Instant Messaging, as the common Jabber support with presence server

  I hope this helps.

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• VCS - C leave IP address directly with VCS - E also

  Hello

  I have a VCS - C with a VCS-E in an environment x7.0

  The majority of endpoints are registered on the VCS - C, but there are some points of endpoints that are not for specific reasons.

  Endpoints are not registered in the VCS - C can call termination points registered by its IP address, but the end point registered can not dial end points unregistered. I understand that this is normal with the indirect numbering and the VCS-E but y at - there a way around this direct IP activation on the VCS - C and the use of a search rule that everything that does not correspond to a 10. hit the VCS-E?

  I'm doing a lab to do the test but would be great to see some comments on this.

  Thank you

  Hello

  You can work around this by creating a subarea on the VCS - C with one or several partners subzone composition one or several rules of type "Subnet", where you set of these endpoints unregistered IP addresses/ranges.

  This will have the effect that when registered endpoint contains an IP address appearing in one of this subarea subnet-type membership rules, the VCS - C will consider the known IP address and continue to attempt to place the call to that specific IP address.

  It will be easier for you if these unregistered end points were easy to define subnet membership rules, for example if they are all in the same subnet, rather than spread around different subnets, without overlap.

  -Andreas

• TMS with CUCM registered devices

  I'm reviewing a BOM for a customer, and the current proposal has:

  CUCM 9
  Lane Express Core
  Side of the highway
  TMS
  vTelepresence Server

  Finally, I have checked, we needed VCS control to allow some TMS plan the server TP. With the current software (CUCM 9.x, TMS 14.4, etc.) can I use TMS to annex CUCM registered endpoints and TP Server, if the server TP is to shared resources directly to CUCM? There is no conductor in this deployment. Looking for a validation test.

  THX,

  Rob

  Hi Rob,

  Since version 14.4, TMS supports the planning of bridges that are shared resources to the CUCM, so limiting earlier 'all bridges must be deployed on the side of VCS' is no longer valid.

  However: TMS can plan only telepresence servers who are in managed mode locally. Telepresence virtual servers don't support not mode managed locally, so if you want distributes them TMS, you will need to put a conductor in the mixture.

  Kind regards
  Kjetil

• Cisco Jabber (Movi) &amp; VCS - E receives no video &amp; audio

  I have a Setup with a VCS Expressway Starter pack (X7.1) where the 2 Ethernet interface is connected to an internal network on 192.168.x.x and interface Ethernet 1 is connected directly to the Internet (through a router to the Internet provider).

  Inside the network I have a few points endpoint TC5 & TC4 and a MCU. Communication of all these endpoints to the Internet works very well for the SIP and H.323.

  I also have a number of accounts on the VCS E Jabber/Movi.

  Registration of Jabber accounts to the VCS-E works very well to both internal and external networks.

  Use on these (v4.3) Jabber account on the internal network or external contact points of termination/SCM on the internal network, there is no problem.

  When you use the same Jabber account to call another endpoint on the Internet, I always a one-way communication, IE the Jabber does not get the video and voice.

  I took a few traces of the VCS-E network but did not find the problem.

  Any ideas what could be the problem?

  Rgds, Geert Folens.

  Greet them salvation.

  Excellent... I am pleased that it resolved your problem. I would be grateful if you set the thread as answered!

  See you soon

  Alok

• With VCS-E media stream, VCS - C

  Hello

  We intend to implement a VCS infrastructure now I'm not sure wich accepting media between endpoints.

  On the photo, you could see the scenario.

  Endpoint 1 is communicate with the endpoint 2.

  1 medium Wich takes the media stream?

  2 what endpoint 1 communicate (media) with VCS - C and not directly with the two end point?

  2. must a direct connection between two end points?

  Thank you

  Martin

  Hi Martin,

  the media could pass control of VCS and highway always in a solution of course and course usage license.

  endpoint 1 must send to the control of VCS, and then it will be passed to the fast lane and then on internet and internet endpoint not directly.

  Rgds,

  Alok