Cisco Jabber with VCS

Similar Questions

• Cisco Jabber with Cisco multi-party Shared more Licenses

  Hello

  I'm looking for a Solution to video conference for approximately 4000 employees. Currently the customer uses Cisco's Jabber for video calls from point to point. The main requirement is Ad - Hoc videoconferencing by any employee at any time. I looked at both meeting of Cisco and Cisco TelePresence Server server. The two solution requires more or licenses more pluralistic multi-party Personal shared. The customer won't buy a PMP license for each user. Their requirement is multimedia resources shared so that any employee can initiate an ad hoc conference.

  Now the question is: can we use Cisco Jabber with multiparty licensing shared?

  Thank you

  Mockus S

  Yes, it is quite possible.

  The only singularity is with PMP + which applied slightly differently than the head of the Orchestra/vTS. This does not seem to match your use case since you intend to buy only SMP licenses +. From version 2.0 (1) CMS, PMP + licenses - which are less expensive than SMP + - use only if: a) the space belongs to a LDAP user with a PMP + license for which they are responsible; or (b) If a user LDAP with PMP + assigned to them joins the Cisco meeting App space as an authenticated user. In all other scenarios, including ad-hoc escalation with CUCM licensed SMP + is consumed. This is different from that of head of the Orchestra/vTS, which were also able to understand the right to the user for ad-hoc calls.

• Comments of Jabber with VCS registered endpoint control and MCU

  Hi all

  According to my plans. I'll try to integrate comments Jabber with environment of Collaboration.

  Use cases;

  1. call between Jabber and VCS registered control EX90 comments

  2. Add Jabber comments a MCU conference where MCU part control VCS

  3. call between Jabber and Jabber comments

  Comments will be welcome :)

  Best regards

  Mesut

  Hi Martin,

  From Jabber comments 10.0, only #3 above is supported. However, we will publish JG 10.5 soon (I hope that in the next few months), and it will support all 3 of your above use cases. The only downside is to use #1 and #2 cases, you have a CUCM in the call flow.

• Cisco Jabber (Movi) & VCS - E receives no video & audio

  I have a Setup with a VCS Expressway Starter pack (X7.1) where the 2 Ethernet interface is connected to an internal network on 192.168.x.x and interface Ethernet 1 is connected directly to the Internet (through a router to the Internet provider).

  Inside the network I have a few points endpoint TC5 & TC4 and a MCU. Communication of all these endpoints to the Internet works very well for the SIP and H.323.

  I also have a number of accounts on the VCS E Jabber/Movi.

  Registration of Jabber accounts to the VCS-E works very well to both internal and external networks.

  Use on these (v4.3) Jabber account on the internal network or external contact points of termination/SCM on the internal network, there is no problem.

  When you use the same Jabber account to call another endpoint on the Internet, I always a one-way communication, IE the Jabber does not get the video and voice.

  I took a few traces of the VCS-E network but did not find the problem.

  Any ideas what could be the problem?

  Rgds, Geert Folens.

  Greet them salvation.

  Excellent... I am pleased that it resolved your problem. I would be grateful if you set the thread as answered!

  See you soon

  Alok

• CUCM (Cisco Jabber) - VCS - MCU (failed appeal of SIP - SIP)

  Hi all

  in our Videoinfrastructure, there is a little problem with cisco jabber client registry on the CUCM to our MCU.

  The MCU is inscribed on the VCS.

  If I make a call my Client of Jabber Cisco SIP call has failed. I call the number 4925488XXX. The callingparty is the 25203232.

  In the CUCM, there is a Routepattern who translated the «Called Party Number» number = 8099 (this is the SIP Trunk for VCS).

  Called Party Transformations:

  Called mask = 8XXX

  Take the numbers Instruction = None

  Prefix =

  Called number = 8099

  In venture capital, there is a transformation for the 8099 dialed.

  

  The MCU is registerd with [email protected] / * / on the VCS - it's self attandant.

  In the Cisco Jabber client I never receive video or audio of the MCU AA - it looks like the call's not connect.

  If I spent a glance in the VCS, I see the appeal as active and connected.

  

  Also, I traced the call made by the VCS in debug mode.

  SIPMSG:

  | SIP/2.0 180 ringing

  Via: SIP/2.0/TLS CUCM IP SIP; direction = z9hG4bK10ea4511f7965; has received = CUCM; penetration area = CUCMUC

  Call ID: [email protected]/ * /.

  CSeq: INVITE 101

  Contact: <> [email protected] / * /; GR = urn: uuid:c4a744d7-5975-52db-b21c-8c519fbab06e >; isfocus

  From: Stefan Walter "' <> [email protected]/ * */>;tag=252394~c75f2de1-fd7b-43c2-8bd0-6b72860c9048-46890229

  To: <> [email protected] / * / IP >. tag = 11B05829C2080000

  Record-Route: <> [email protected] / * / SIP; transport = tls; LR >

  Record-Route: <> [email protected] / * / SIP; transport = tls; LR >

  User-Agent: Codian MCU 4505 v4.3 (2.18)

  Content-Length: 0

  |

  "2012 10-26 T 15: 33:25 + 02:00 DDUCP001 tvcs: elements UTCTime ="2012-10-26 13:33:25, 230"Module =" network.sip"Level ="INFO": Src - ip = 'CUCM IP' Src-port ="39813"detail =" receive the method Request = CANCEL, Request-URI = sip:[email protected] / * / IP, Call-ID =[email protected] / * / IP.

  2012 10-26 T 15: 33:25 + 02:00 DDUCP001 tvcs: elements UTCTime = "2012-10-26 13:33:25, 230" Module ="network.sip" Level = "DEBUG": Src - ip = 'CUCM IP' Src-port "39813" = "

  SIPMSG:

  | CANCEL sip:[email protected]/ * /: 5061 SIP/2.0

  Via: SIP/2.0/TLS CUCM IP SIP; direction = z9hG4bK10ea4511f7965; receipts = 10.202.131.96

  Call ID: [email protected] / * / IP

  CSeq: the 101 CANCEL

  From: Stefan Walter "' <> [email protected] / * / IP>;tag=252394~c75f2de1-fd7b-43c2-8bd0-6b72860c9048-46890229

  To: <> [email protected] / * / IP >

  Max-Forwards: 70

  Date: Friday, October 26, 2012 13:33:25 GMT

  Reason: Q.850; cause = 3

  Content-Length: 0

  ########################

  Reason: Q.850; cause = 3; text = "no route to the destination.

  Do you have any hint for me where I can troubleshoot further? It's a question MCU or CUCM or VCS?

  Good bye

  Stefan

  Hi Stefan.  I would probably run a Trace SDI on the CUCM as well.  Seems the cancel is coming from CUCM side and end the call.  To check that your possibly fall on: CSCty07061, I could run the trace of the SDI and see after reception of 180 ringing of venture capital if he tries to do a DNS query for @mcu.

  The entries may look like:

  | 1.3508793, 63, 100, 2 ^ 10.52.36.15 ^ *.

  11:20:09.377 | / / SIP/SIPDns (2,72,1) / wait_SdlDnsSrvRecordRsp: received specified SdlDnsSrvRecordRsp is - 1. 0, 0, 0, 0.0 ^ * ^ *

  11:20:09.377 | / / SIP/SIPDns (2,72,1) / copyRecordRspToRecordReq: query retry SRV as a 1 request | 0, 0, 0, 0.0 ^ * ^ *

  11:20:09.377 | / / SIP/SIPDns (2,72,1) / wait_SdlDnsSrvRecordRsp: hostname (DNS A or AAAA query called a query SRV Fail) = mcu

  --------------

  If that's what your race, false address to solve the @mcu would be required for the call to go forward.  I have this based off the coast an explanation here, but cannot actually ensure that it's what your run in.  But check the trace of the SDI AFTER the 180 ringing and see.

  I hope this helps.

  VR

  Patrick

• iOS 10 with Cisco Jabber

  Dear Cisco support community,

  as seen on http://www.apple.com/ipad/business/work-with-apple/cisco/

  Only the spark is described here. There will also be a better integration of the call with Cisco Jabber?

  Spark.PNG

  

  According to me, they're trying to transmit only apple ios 10 best interactive aura to the customer of the spark. This does not mean that jabber for iphone will be less functional in ios 10.

• What is the difference between the video of Cisco Jabber of jabber, WebEx, Cisco

  Hello

  I started reading about Cisco jabber for a few days. I couldn't make out the clear disctiction between Cisco Jabber, WebEx and Cisco Jabber video. What is the difference? Also the one who uses the API of the other? What is APIs that WebEx Cisco Jabber or Jabber user video using the WebEx API?

  Thanks in advance :)

  Does this help: http://www.cisco.com/web/products/voice/jabber.html

  Jabber is a BRAND name for a range of products to run on a variety of devices.  Mainly desktop and mobile.

  It requires not more CUCI.

  WebEx Connect (with CUCI Connect) is/has migrated to Jabber

  CUPC is/has migrated for jabber

  The Jabber SDK is very powerful (url above understands this as well)

  Jabber for telepresence is the old MOVI (Mobile Video) of the Acquisition of Tandberg and more than one piece of theater for VCS registration and control.  But most of the jabber brand above 4 video.

  There will be subtle differences between different brand of jabber clients, so don't read a J4Windows guide and think it's the same for the iPad or Android for example).

  But its great.  Head to head with Lync.

• Integration of video telepresence, Cisco Jabber

  Hello

  How are you?

  I have a question, can Cisco Jabber video join a standalone VCS? or is it also a TMS? on his page it is said that a requirement is the MSDS, but if a customer has a VCS with TP EP registered him, he wants to allow video jabber as well on the network and wants to know if it can be done without the need to obtain an MSDS.

  can someone help me?

  Please

  Sincerely,

  Dante Verastegui

  For a demonstration of the concept starter pack a VCS may be feasible, but if you start with

  CTS systems, I would say it is a nogo

  You use CUCM for CTS systems, have the VCS - C for your internal network where

  JabberVideo and MX200 can register and then the VCS-E for external/b2b communication and

  Maybe external registration + TMS to manage.

  The requirement for growth of each message, I suggest you really join Cisco (partner). :-)

  Please note the messages using the stars below!

• Integration: Jabber with VCSC

  Hi experts,

  I'm new in the world of telepresence and I will install into a new customer a solution with VCSC, TMS and MCU.

  The customer already has a CUCM with Jabber and they want to deploy the Jabber with VCSC, they want that, for example, a Manager actually a video conference with other offices through your Ipad with Jabber

  I have not found a document with this configuration, can someone help me with the documentation of this integration?

  With their experience of telepresence, including the complexity of this integration? Can give me of highlights and key points of this integration?

  Best regards

  In addition to what Alok suggested, there are other things, you should consider:

  • The version of the recommended software is CallManager 8.6.2 and later (you can try 8.5.1, but there is no support BFCP)
  • It must integrate CallManager and VCS by following this document:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/VCs/config_guide/Cisco_VCS_Cisco_Unified_Communications_Manager_Deployment_Guide_CUCM_8_9_and_X7-2.PDF

  • To enable content sharing between registered in CUCM Jabber and the end point registered in VCS, make sure that your Jabber in CUCM devices have a SIP profile with BFCP protocol enabled, as well as the setting "Allow presentation sharing via BFCP" set to allow.
  • If you want to schedule conferences in MSDS for the Jabber in CUCM, you can add them to TMS as a 'room '. By using this option, you will be able to plan the Conference and the calendar control (it's better than using the Participant model)
  • About the phone book, you might have some problems. If your devices registered in VCS use device with an alphanumeric URI address, for example [email protected] / * /, you will not be able to add this contact to Jabber clients registered with CUCM, alphanumeric once is not supported. A solution would use only digital device address for all devices. About Jabber for Telepresence, you can define directories using TMS, in this case, you can add contacts without problem, either using a digital or non-digital address.
  • If you have endpoints another enrolled in CUCM who will call the end points registered in VCS, make sure your devices are running compatible software versions, mainly the videophones. It is strongly recommended to use the latest version of the software.
  • Be aware that Jabber for Telepresence doesn't support Instant Messaging, as the common Jabber support with presence server

  I hope this helps.

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• Cisco Jabber

  Good afternoon; I have the Cisco Jabber Software running on an Iphone 6 Plus, everything works well when the phone is unlock, when the phone is locked can not answer the calls received by the Cisco Jabber only a window appears with a message that I have a call, but I can't answer. Is there a way to solve this problem. ????

  Greetings.

  Fernando

  Since this request is not an Apple application, I suggest make you contact with the developer of application or their support and ask your question.

• Cisco Jabber on iPhone lost configuration settings

  After my upgrade to iOS4 for iOS5 on my iPhone the Cisco Jabber client lost configuration.

  As a user, I have to configure at least the device ID and the TFTP server.

  What is an iOS or problem Cisco Jabber and y at - it a fix for this problem.

  Alex

  Sent by Cisco Support technique iPad App

  Thanks for the details. iOS 5 is compatible with Jabber for sure, but at least, I got the info for Cisco Mobile 8.1.2 customer & don't know if tests for 8.5 is over. If you are a Cisco partner, you might want to open a case with PDI www.cisco.com/go/pdihelpdesk Helpdesk so that the PDI team it can confirm for you.

  In the meantime, have you tried reinstalling the client, which could solve the problem of too.

  HTH

  GP.

  Pls rate useful messages!

• Cisco Jabber registration fails.

  Hi, I have a problem with Cisco Jabber request the Android.It fails to sign the CCM.

  CCM version is 8.5, Cisco Jabber is 8.6.1, I followed the documentation

  http://www.Cisco.com/en/us/docs/voice_ip_comm/cumc/cisco_jabber/Android/86/Cisco_Jabber_Android_8.6.x_Admin_Guide.html#wp810478

  And everything looks good. DNS works, I can reach the CCM web portal on the phone's web browser.

  You have some tips how to troubleshoot, for example what newspapers is RTMT would be useful, or if there are balls on Jabber.

  Any help would be appreciated

  I changed the CUCM hostname under system-> server-> to the IP address of the CUCM and now the Jabber client is registered and to obtain the DN. But I'm unable to make or receive calls.

  Any help.

  Kind regards

  Abraham

• Cisco Jabber for Windows - Added new friend

  Hello

  When I try to add a buddy to our internal directory, it does not work. For a short time the new boyfriend is in the buddies and then rinse... never again. In the presence of CUP Viewer, you don't see also no boyfriend.

  When open UPC 8.5.x then, it works perfectly. If the two (Jabber and UPC) has started, add new buddy in! Jabber! and in the UPC he is there. Jabber is not not do anything this boyfriend.

  If now! The new boyfriend UPC or Jabber logs by himself... it would have shown in the buddies of the Jabber Client at all times. But the other guy must be connected by itself.

  (1) file-> new-> contact

  (2) looking for someone

  (3) define the Group

  (4) add

  External friends... added to the list works and they stay there.

  Here the break error report.

  thx for all the help phil

  One of your user names contain a space by chance?  Because I see a similar behavior and I followed it down to user names (and therefore IM addresses) that contain spaces fundamentally break totally Cisco Jabber, but CUPC 8.5.5 works very well with them.

• Cisco Jabber 10.5 for Windows boot process

  Hi guys,.

  I had following problem and impossible to find a clue that can move me somewhere.

  A customer has a jabber Cisco 10.5 deployed and integrated with Active Directory.

  Every day, customers are initializing requests of sends customers jabber with phone numbers against the AD domain controller (these figures are not the contactlists - personal or company) and as there is that much more of this question in a moment the utillization of the announcement is almost 100%, which also makes the problem with the connection in outlook (is also integrated with the Cisco Jabber for windows)

  I searched the Web for tips but have not found anything.

  My questions are:

  The data for Outlook Personal AddressBook starting the Jabber questioned via Jabber Localy or domain controller?

  What is the process of starting the Jabber for Windows on the integration of directories?

  Is this a normal behavior of jabber?

  #####################################################################

  Here is the configuration of the config.xml file - jabber (passswords and areas are changed):

   
        BDI
          AD
          AD-IP address

  Field of presence
             389
              DC = presence, DC = domain
         Username
          Password
          Fake
          True

  ###########################################################

  Hello

  Jabber will not interview contact Outlook address book DC until a manual search is made.

  Also default contact jabber, the domain controller for the windows PC host.

  Each time that you enter at least 3 characters (default for search), jabber first find cached contacts, then outlook address book and then search the directory.

  The attached config file is BDI type ie. for MAC computers, it will not take effect in windows PC.

• Cisco Jabber for Windows user Photos

  8.6.3 CUPS

  Client Jabber for Windows Version 9.0.1 Build 8802

  I noticed that Jabber Client for Windows Cisco does not automatically refresh with updated photos in Active Directory.

  I had updated the user photo in AD and noticed that he wouldn't. I travelled to "C:\Users\\App Data\Local\Cisco\Unified Communications\Jabber\CSF\Photos" and had to manually delete the users photos in this folder. I left on the Jabber Client and restarted the program. When I did this, crashed the Jabber Client, I saved the report of crash and re-opened the Jabber client. This time the customer opened correctly, and the photos update appeared now!

  It seems that Cisco would not set the photos to be cached on the local computer.

  Any thoughts?

  Hey Ellen,.

  Looks like the similar problem with CUPC. Previously, I had a discussion with our Dev team for CUPC Photos of caching locally.

  This has been identified in the following improvements:

  CSCtu25084    CUPC Contact photo put in cache and do not update dynamically

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtu25084

  I will update to add Cisco Jabber for Windows as well.

  Best regards

  JAS