TMS with CUCM registered devices

Similar Questions

• A button to push on CUCM registered endpoints

  Hi all!

  I tried to implement a buton to push with CUCM registered endpoints. As far as I understand it, the system must be added to the MSDS directly and not only as the room, therefore RSI can push messages to the endpoint. If I add endpoint to TMS I get error, that endpoint has put the wrong type of provisioning. Accordingly, I am not able to change the settings of reservation, as allow remote booking for MS Exchange integration.

  BBFRR may be available for endpoints registered or is - CUCM this only available for registered endpoints VCS?

  BTW: versions:

  TMS 14.3.1

  TMSXE 3.1.2

  9.1 2 CUCM

  Conductor X2.2

  TS3.1

  Kind regards
  Paul

  [...] If I add the endpoint to TMS I get the error, that the endpoint has set the wrong provisioning type. [...]
  
  

  Hello

  Did you add endpoints to TMS the correct way, i.e. "to list" > "Unified CM?

  Kind regards

  Kjetil

• Range of Ports RTP endpoints TC changed after registering with CUCM

  Hello community,

  We have SX80 endpoints running TC7.3.2 and registered at CUCM 11.

  By default the TC ports rank 2326-2487 UDP RTP endpoints. After registering with CUCM, the range of ports have been changed to 16384 to 32766. In my view, WHAT CUCM change the codec settings.

  rtp_ports.PNG

  

  Based on the http://www.cisco.com/c/dam/en/us/td/docs/telepresence/endpoint/codec-c-series/tc7/administration-guide/administering-endpoints-running-tc72-on-ucm1051.pdf guide I couldn't see any setting to do with RTP ports.

  This is a problem for us, because on the firewall rules, we have configured and fixed ports for points endpoints use the default go 2326-2487 UDP. Because these endpoints and video infrastructure (servers of telepresence, TCS, VCS) are on different networks separated by firewalls. At present, when recording and join the conference bridge there are no media because ports have been changed. When I change the default port range, there is no problem with the media. I can record and call to the conference bridge hosted by a TP server successfully. And if I hit the button refresh on the web GUI of the codec, 16384 to 32766 changes the settings.

  Y at - it a setting that I could check on the side of CUCM?

  Thanks in advance.

  «By default the endpoints ports rank 2326-2487 UDP RTP TC.» After registering with CUCM, the range of ports have been changed to 16384 to 32766. "I believe THAT CUCM change the codec settings".

  Yes, it's true. Once your video endpoint is configured and registered on the CUCM, the CUCM will be more than just the default settings of your endpoint. It depends on the SIP profile has been used and applied for your endpoint. You need to check that the configuration of the SIP profile of the CUCM applied for your endpoint. In your case if it's SX80, check the SIP for SX80 profile and change the start and stop media ports. It comes to the RTP port range.

  In your case:

  Port of bootable media: 2326

  Stop Media Port: 2487

  rtp_cucm.PNG

  

  Kind regards

  Acevirgil

• MGCP FXO does not register with CUCM on VG204XM

  I have a VG204XM running MGCP with CUCM 10.5. When the port is changed and reset him CUCM config push down to the VG204XM there is an error (it is identical to the Bug CSCtr78616 reported on a router 28xx in 2011)

  In the newspapers, I see that, once the router receives the config it tried to configure AALN/S0 / / 0 (voice-port 0/0)
  However, for some reason, it seems that the router is to convert the port to a 65535 instead of 0

  "cmapp_xml_get_interface_info: slot = 0 vic = 65535 port = 0".

  Since the port above does not exist on the router the survey attempt a mistake.

  Mar 27 18:07:59.278: % SYS-5-CONFIG_I: configured from console by console
  Mar 27 18:07:59.278: cmapp_xml_get_interface_info:
  18:07:59.278 Mar 27: =.
  Mar 27 18:07:59.278: cmapp_xml_get_interface_info: slot = 0 vic = 65535 port = 0
  18:07:59.278 Mar 27: Interface_name: AALN/S0/0
  Mar 27 18:07:59.278: controller:
  18:07:59.278 Mar 27: addr: 65535/0/0
  Mar 27 18:07:59.278: interface:
  Mar 27 18:07:59.278: voice_port: voice-port 65535/0/0
  Mar 27 18:07:59.278: dial_peer: voice dial-peer 9990655350
  Mar 27 18:07:59.278: dial_peer_port: 65535/0/0
  Mar 27 18:07:59.278:
  Mar 27 18:07:59.278: cmapp_xml_configure_router: verification of the Deleted interfaces
  Mar 27 18:07:59.278: cmapp_xml_get_intf: looking for a vdb [65535/0/0]
  Mar 27 18:07:59.278: cmapp_xml_configure_router: analog ports are ready
  Mar 27 18:07:59.278: cmapp_xml_find_corr_intf_cfg:
  Mar 27 18:07:59.278: cmapp_xml_find_corr_intf_cfg: old_cfg is NULL
  Mar 27 18:07:59.282: cmapp_xml_intf_cfg_changed:
  Mar 27 18:07:59.282: old intf configuration is null
  Mar 27 18:07:59.282: cmapp_xml_cfg_analog_intf:
  Mar 27 18:07:59.282: cmapp_mgcp_get_card_type_for_analog_intf: looking for a vdb [65535/0/0]
  Mar 27 18:07:59.294: cmapp_xml_cfg_router_intf: intf configuration: [voice-port 65535/0/0]
  Mar 27 18:07:59.294: cmapp_xml_cfg_router_intf: configuration [echo - cancel enable]
  Mar 27 18:07:59.298: % SYS-5-CONFIG_I: configured from console by console
  Mar 27 18:07:59.298: cmapp_xml_cfg_router_intf: 395 line router configuration error
  Mar 27 18:07:59.298: cmapp_xml_send_msg_to_callmgr: CMBH_MSG_CFG_ERR of sending
  Mar 27 18:07:59.298: * info ERROR: the router configuration failed: voice-port 65535/0/0
  echo - cancel enable
  end

  I have a VG224 gateways running with MGCP CUCM 10,5 and no error

  Everyone knows about this problem on VG204XM?

  Hello

  Please check

  https://Tools.Cisco.com/bugsearch/bug/CSCui83022/?reffering_site=dumpcr

  Auto config MGCP fails for VG204XM
  CSCui83022
   

  Description

• SX 20 with CUCM 8.6.1

  Hello

  I need to record 20 peripheral SX with CUCM 8.6.1, but SX 20 is not available in the list of devices!

  How can I register it?

  Regds

  $

  Hello

  CDP file will be used for the endpoint SX20 push updates of software and the package devce for the CUCM, where it must be installed separately.

  as mentioned in the document provided by Vivek:

  Installation instructions

  Note: Cisco recommends that you apply this device for a package

  maintenance window.

  Note: Packages of devices are installed on the active partition and cannot be

  uninstalled;

  Cisco recommends that you take a backup DRS prior to installation.

  For more information on how to do a proper backup, see the Recovery Guide disaster for each version of Cisco Unified Communications Manager.

  Procedure

  Note: Apply this package of device to all of your Cisco Unified Communications

  Manager servers, starting with the publication server and the TFTP server.

  Note:

  When you apply a device Package to activate the new device support, a broad cluster restart is necessary for these devices to record successfully.

  A

  Cluster - wide restart is not required when you apply a Package of device for the update of the existing firmware/media. Cisco Unified Communications Manager 8.6, you perform all software installations and upgrades by using the software update menu options. The system can load and process only the software that Cisco has approved. You may not install or use third party or Windows - software applications that you used a previous version of Cisco Unified Communications Manager.

  1 from your web browser, go to the web page of Cisco Unified Communications Administration of the operating system.

  2. in the menu of the software upgrades, select Install/Upgrade.

  3. fill in the appropriate values in the section where the software and click Next.

  4. in the available software drop-down list box, select the device package file

  Click next

  5. check that the MD5 has the correct value. Click Next.

  6. in the warning box, verify that you have selected the right firmware and

  then click on install.

  7. check that you have received a message of success.

  Note:

  If you restart the cluster, skip step 8.

  8. stop and restart the TFTP server.

  9 reset the devices concerned to upgrade the devices to the new load.

  Hope that helps

  Concerning

  KR Ravi

• Cisco C40 unsubscribe automatically with CUCM 8.6.2

  Hello

  I have Cisco C40 connected to CUCM 8.6.2.

  First, he is registered with CUCM and I was able to call on another phone C40.

  Then, C40 automatically BSW of CUCM and isn't recording with CUCM now.

  I added C40 via device-> phone-> Add new-> then selected Teleprecense C40

  C40 SW version is: 5.1.5.297625

  I joined C40 and CUCM screenshot. It shows not recorded, which proves C40 registerd at least once.

  I could make and receive calls with the C40 for a few minutes. Subsequently recorded automatically and now

  error message is status: failed

  Suggest pls.

  Rgds

  Rajesh

  Hi Renon,

  Please below changes made in the SIP settings:

  change SIP profile 1 Type at Cisco, since it is native enrolled and default transport for TCP

  * c xConfiguration SIP URI 1 profile: "[email protected] / * / "

  "

  * c xConfiguration SIP profile 1 DisplayName:

  * c xConfiguration SIP DefaultTransport 1 profile: TCP

  * c xConfiguration SIP profile 1 TlsVerify: Off

  * c xConfiguration SIP profile Type 1: Cisco

  * c xConfiguration SIP profile 1 outgoing: Off

  * c xConfiguration SIP profile 1 Proxy Discovery 1: manual

  * c xConfiguration SIP Proxy 1 address of profile 1: "172.31.131.10."

  * c xConfiguration SIP profile 1 Proxy Discovery 2: manual

  * c xConfiguration SIP Proxy 2 address of profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 3: manual

  * c xConfiguration SIP Proxy 3 address profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 4: manual

  * c xConfiguration SIP Proxy 4 address of profile 1:

  * c xConfiguration SIP profile 1 1 LoginName authentication:

  * c xConfiguration SIP profile 1 1 password:

• VCS Express with CUCM 10

  Hello

  There is a lot of confusion on Express C/E & VCS C/E, if anyone can confirm my following queries:

  With VCS VCS & Express control every endpoint to register with VCS control (no participation required CUCM or VCS control can't integrate with CUCM)?

  With Highway Core & edge that every endpoint is record in CUCM & CUCM will record Expressway Core?

  For calls B2B & movi Jabber, that we must have Expressway Center/periphery, VCS control/Express IS NOT support jabber movi & called B2B?

  Software Express C/E & VCS C/E are the same, but the licenses are different?

  Our clients have obtained

  1 x control VCS licensed

  1 x Express VCS under license

  1 x ISDN gateway,

  1 x TP driver

  1 x TP management suit.

  Kind regards

  Francisco

  With VCS VCS & Express control every endpoint to register with VCS control (no participation required CUCM or VCS control can't integrate with CUCM)?

  Yes, no CUCM is required, endpoints can also enroll in the VCS-E or it could register SIP to VCS - C proxy endpoints. A parallel installation of VCS CUCM with a trunk should also work with todays versions.

  The VCS will be only support standards basis of endpoints SIP and H323, its main purpose

  a for video settings. You won't be able to use it to register, provision or use of Cisco IP phones with it.

  With Highway Core & edge that every endpoint is record in CUCM & CUCM will record Expressway Core?

  See the C & E highway as a single unit to the external communication. The registrations are transferred by proxy

  CUCM outside.

  But that also means, you can't register 3 party at the highway and even end points

  Cisco endpoints must support the installation of the fast track C & E.

  The highway also runs things like XMPP for Jabber.

  For calls B2B & movi Jabber, that we must have Expressway Center/periphery, VCS control/Express IS NOT support jabber movi & called B2B?

  The C & E Highway can also manipulate calls business2business or another sip trunks / h323, but this infrastructure requires the media license.

  B2B calls also works very well with the installation of VCS.

  If you are talking about how to provide Jabber accounts and video Jabber:

  There are video Jabber (which is implemented by TMS and VCS) and Jabber (i.e. led CUCM) there.

  If you are talking about outside calls that he can just be regarded as regular b2b external calls.

  then they be it work with VCS or motorways on the site of the end.

  Software Express C/E & VCS C/E are the same, but the licenses are different?

  It is correct. Licensing Expressway is more attractive for users CUCM, but you already have

  have SPRDD in place that should work in all cases well.

  With CUCM, you get licenses Expressway in any case. So according to the type of use, you.

  B2B, internal calls... you can add a configuration of fast track to Jabber and the stuff of office home and

  use the VCs to B2B and part 3 records.

• Unity connection 8.6 Migration to 11 with CUCM 8.0

  Due to the right I'm going to intend a Migration of 8.6 connection unit to 11.0 of connection of the unit before I can improve CUCM. I am sure that the answer is Yes, but would there be problems running 11.0 of connection of the unit with CUCM 8.0.

  Nothing fancy on the face of connection of the unit, no unified messaging ect.

  New UC 11.0 should just registered the EPSC ports?

  Thank you

  Dan

  Looks like you need at least version 8.5 for the SCCP and SIP integration CUCM to be supported. Check the compatibility of connection of the unit guide below.

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/connection/compatibil...

  Combinations for Cisco and unity connection Unified Communications Manager of the supported Version

  Table 22 Version combinations of supported for the connection of the unit and Cisco Unified Communications Manager

  Cisco Unity Connection	Cisco Unified Communications Manager
  8.5 and later	11.5 (1), 11.0 (1), 10.5 (2), 10.5 (1), 10.0 (1) 9.1 2, 9.1 (1), 9.0 (1), 8.6 (2), 8.6 (1), 8.5 (1)

  SIP: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/compatibil...

  -Terry

  Please note all useful posts

• Exception of HTTP after migrating TMS with TMSPE

  Migrated 13.2 TMS with TMSPE physical server in VM 2008R2, which went well, however, VCS - C is now sent me some exception HTTP State for all services supply; users, directories, and devices.

  Status: failed

  Answer: HTTP Exception

  Reason: HTTP error (400): WWW-Authenticate

  And yet, diagnostics in TMS TMSPE shows no alarm; It's all green.

  However, TAC is working on it.

  Someone at - he seen this before?

  /Jens

  Thanks for the clarification, Jens and I'm talking internally for all involved here because it seems we have "several hands in the kitchen" (as well as the different cuisines) concernng this one... which means that we will use the official channels for troubleshooting it and we'll just update this thread with leading... agreed?

• Telepresence EX60 with CUCM 8.5 - How to integrate?

  Good morning people,

  I'm building a lab with 8.5 CUCM and presence Server 8.5

  I'll install the Cisco TelePresence EX60, and I wonder how I do integration with CUCM.

  Need to install the additional server? You simply add a SIP device in CUCM?

  Can someone help me?

  Thank you

  Bruno

  Hello.

  You must have CUCM 8.6 in order to utlize the full potential of the CUCM / integration EX60. You save the unit directly to the CUCM.

  I recommend you take a look at this guide, after that you did with your laboratory update.

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC5/administration_guide/cts_endpoint_administration_ucm86_quick_start_guide_tc50.PDF

  I have attached a screenshot showing how it should look like the description of the device.

  Thank you

  Marius

• c 60 with CUCM 7.1.5

  Dear all

  I have 60 C with CUCM 7.1.5 and software version 5.1.4.  I want to save it as a 3rd party (advance and basic) SIP device. but I can't save it. kindly help.  kindly share the Document.  Thank you

  Yasir Vistro

  Hey Yasser

  You can your CUCM move to 8.6? It would be the easiest as after that you can add C60 as native sip device.

  Thank you

  Rafal

• I have Mac syncs with my iOS devices.

  I have Mac syncs with my iOS devices.

  Why not? What happens when you try? We are not psychic.

• Why has my connection AirPort Extreme recently stopped with my Tablet Android and Windows 7 laptop, but connects very well with all Apple devices?

  Why has my connection AirPort Extreme recently stopped with my Tablet Android and Windows 7 laptop, but connects very well with all Apple devices?

  What exact model of AirPort Extreme do you have? Either have your tablet or laptop Win7 been updated recently? They were both able to connect before and not now OR they were never able to connect? Can the laptop Win7 access Internet when connected by Ethernet? One of these devices have problems connecting to other networks Wi - Fi?

• Satellite M45-S359 equipped with a bluetooth device?

  Satellite M45-S359 equipped with a bluetooth device? Well, if it was, I don't know how to use uu

  Hello

  According to this page Bluetooth and antenna for Bluetooth device no is not available on this device.
  http://www.toshibadirect.com/TD/B2C/pdet.to?poid=306224&SEG=HHO

• How can I share my library with all my devices

  How can I share my library with all my devices?

  In the article to share your iTunes library on your home - network Support Apple its pretty simple from what I've read, just make sure you have sharing options enabled in iTunes on your computer.

  Just make sure that you are signed in the same Apple ID on all your devices and turn on sharing House on each of them as well and make sure that you are connected to the same network, trying to share the library.