Common 'problem': network interface

Similar Questions

• VCo workflow to clone a virtual machine of centos. Network interface problem

  Hello

  I use vco workflows to clone a virtual machine of vcenter. The virtual machine is running centos 6.0. When cloning is complete. I see the network eth0 and eth1 interfaces set correctly the static gateway ip and address information I provided. I deleted the 70 - persistent - net .rules on the basic vm form which I clone. So, I get the correct interface names. But when vm powers on and I run "ifconfig eth0" I don't see the IP address of this interface has all the details.  same for the other interface also.

  But if I do a system restart network without changes to networking and then do an ifconfig I see the IP with the previous information.   I don't know why the service network restart is necessary so that he can recognize the ip address.

  Any ideas what I could do wrong. or to avoid this manual step of the execution of the service network restart command on the creation of the vm.

  Thank you

  Kiran

  Yes I'm restarting after after the application of customization.

  Has been able to solve the problem... In CentOS, the network service does not work by default. This is why it does not have network interfaces at startup. So now the machine instant, I started the network services and stop the Network Manager service

  using chkconfig network on

  chkconfig NetworkManager off

  and then cloned from this virtual machine... and apply the customization settings. during the start now it shows the interfaces properly without needing a service restart

• Configuration host network interface problem

  Hello

  I use vmware player on Windows 7 Pro.

  After the upgrade to vmware server. I am not able to use the guest only network interface.

  In the configuration interface tcp/ip v4 network, the IP address is 192.168.38.1, but if I run ipconfig, IP assigned to vmnet 1 is 169.254.x.x (invalid IP)

  Anyone has an idea on how to solve it?

  Thank you!

  CESC

  After the upgrade to vmware server

  Just an info, Windows 7 is not a host for VMware Server operating system.

  I am not able to use the guest only network interface. In the configuration interface tcp/ip v4 network, the IP address is 192.168.38.1, but if I run ipconfig, IP assigned to vmnet 1 is 169.254.x.x (invalid IP)

  Unfortunately starting with VMware Player 3, without a valid reason, I've never seen explained, VMware has stopped installing the virtual network Editor.  What I would try to solve the problem is to install manually and then use the restore default in the virtual network Editor to try to fix any problem with network cards virtual VMware.

  ==========

  To install the missing virtual network Editor, the command prompt:

  VMware-player-*.exe -e c:\vmptmp
  

  Then in the c:\vmptmp folder find the file c:\vmptmp\network.cab and extract (double-click on the .cab file) vmnetcfg.exe (virtual network editor) file in the working directory of VMware Player usually 'C:\Program VMware Player' or ' C:\Program Files (x 86) \VMware\VMware Player.  You can create a shortcut and place it with the shortcut of VMware Player, if you want to access it more easily.  Note: there are some for all the files to be extracted to then access the network.cab file.

  Post edited by: WoodyZ - posted: July 5, 2012 09:10

• HP Pavilion a6330f desktop PC: is it possible to update my Network Interface Card?

  Is it possible to replace and modernize the Network Interface Card that I have (10/100 Base-T Network Interface)?  If Yes, do you have a recommendation indicating what replacement card should I buy?  The network interface that I have now I cannot take advantage of very high speed that my internet provider (150mmps).  Thanks for your help with this... Mike

  You are welcome.  Thank you for the additional information.

  Here is a card that should work for you:

  http://www.Amazon.com/TP-link-TG-3468-1000Mbps-Gigabit-express/DP/B003CFATNI/ref=sr_1_1?ie=UTF8 & qid = 1420761130 & SR = 8-1 & Keywords = PCIe-x 1 + Network + Card

  Read the reviews to see what users say about it.  You should disable the network adapter before you install it.  There is a PCI slot and the PCI Express x 1 slot is faster.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• FW 4.1.112.33292 Network Interface

  I just installed the update to firmware 4.1.112.33292 on ix2-dl-10.

  My system status shows a yellow alert that says "the network interface is unavailable.

  I can access the user interface for configuration through the network interface and also actions on the device. for example, it seems to work fine other that he thinks he has a problem.

  I use a static IP address and have had the same setup since I installed the ix2-dl-10 a few years ago. I have not changed any hardware networking since Christmas.

  I'm not 100% sure what FW I was before--I may have jumped the release 33149.

  I tried searching forums and KB, but the research does not seem to do anything.

  I would like to get rid of the error if possible state.

  Please notify.

  Thank you

  -Marty

  Thanks, Gus.

  Currently a submission of the question, the system me towards an article that answered the question:

  https://Lenovo-na-en.custhelp.com/app/answers/detail/A_ID/31596

  A reboot solved the problem. I had not done a reboot because I thought that it was just started after the installation of the firmware, so it would be a waste of time. Shows what I know.

  -Marty

• Fix for common problems associated with Windows Update repeatedly trying to solve the same problem

  When the machine running Windows Update on a Windows XP Professional (SP3 with IE8), the information for the download of the ActiveX bar does not appear. Tried to run the Fix for "Common problems with Windows Update" and it says "Windows Update components must be repaired. Difficulty-it short, reports of success, "Found Themes" saying "one or more components of Windows Update are configured incorrectly". However, still unable to download updates from the information bar does not appear. Repeating the difficulty happens with exactly the same problem i.e. reports etc. but no success still can not download the ActiveX on Windows Update since the information bar never shows up.

  At tried all the suggested solutions I can find for the reported similar problems such as checking the downloads ActiveX security settings, reset Internet Explorer settings, and even resetting Windows Update (Articlce ID 971058) components. Still no luck. Therefore, I am unable to manually check and download updates of Windows security.

  Otherwise my PC works well. Norton Internet Security is installed but did not prevent Windows Update to work on another PC I have. The information bar appears sometimes for other downloads, and it doesn't seem to be a problem on the Windows Update page.

  Please can you help. Thank you.

  No, I'm not not first uninstall IE8 (or IE7) before proceeding with the repair facility...

  Long history, technical, short version: do not uninstall IE8 (and/or IE7) before doing a repair installation (Windows XP only!) leaves the two Internet Explorer and Windows in a State of "confused" or "broken". Your only recourse now is a clean install of Windows (after backup your personal data).

  No, another repair facility won't solve the problem - even if you uninstall IE8 beforehand.

  Follow the instructions in this post of mine in another forum (to-the-letter & in order! ) to restore your computer to a State safe & functional: http://aumha.net/viewtopic.php?f=62&t=44636

  If you need additional assistance with the clean install, please start a new thread in this forum: http://answers.microsoft.com/en-us/windows/forum/windows_xp-system

  Note: The computer must NOT be connected to the internet or local networks (i.e. other computers) in its current state. All your personal data (e.g., banking online & passwords credit card) must be considered at risk, if not already compromised.

  Wish I had better news for you.  Good luck!

  PS: So that registry cleaners can solve some problems (temporarily, at least), they are not & cannot fix what caused the problem. Compare to treat a broken leg with a stick and a couple of BandAids.

• Merge devices with multiple network interfaces

  Hello

  Is it possible to add several interfaces to a device network, but merged into a single device?

  For example, we have a lot of HP and Dell servers that have usually a network interface and an interface of management (ILO or iDRAC).

  It would be useful to be able to add two interfaces while having them mapped on the same server in NMS. The network interface would show us the availability on the network and the management interface may alert us hardware problems via SNMP.

  Anyone knows if this is possible, or do we need to have more than one entry for each server?

  Thanks in advance

  Ewan

  Hi Ewan,

  If the INVESTIGATION period is not recognized by the operating system, we most likely would not be able to draw the individual IP addresses of the ILO or the iDRAC. You can present this as a feature request in the ideas of the community section.

  Thank you

• Dell 3130cn printer network interface does not

  Hello

  I recently reset the printer to my Dell 3130cn to factory default settings. I also reset the LAN interface. After that I did, the network interface has stopped working.

  The printer is not able to get an IP address. There is no solid or flashing lights on at the back of the printer's ethernet port and the printer says its network/IP status as 'unknown '.

  What should I do? I wonder if the network interface is fried. I've never seen this problem until recently. The rest of the printer features seem to work well.

  Hello Josh,.

  Your options are limited, replacement of the on board fresh SST (Y507D) North of $ 400 million. Based on that I would recommend the replacement of the unit. Otherwise, you can connect the printer via USB and share it on the network through the PC.

  Kind regards
  Joseph E

  #iworkfordell

• Unity and double network interface cards

  The unit works well with 2 network cards? Tips or tricks if you use 2 network cards? They are one of the subnets differnet 2. My voicemail ports are registered in CallManager, but on a different subnet from the CallManager is on. And this isn't the MAC for the NETWORK card that my license file is for.

  Two NETWORK adapters is supported only in a configuration Active / Passive with the unit. Both NICs must share the same IP address. 2 cards using NETWORK in an active scenario can cause audio one-way and MWI problems. Please see the links below for confirmation.

  Configuration and troubleshooting of network interface cards double for Cisco Unity

  http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/products_tech_note09186a00801d1c56.shtml

  Troubleshooting Cisco Unity

  http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/prod_troubleshooting_guide_chapter09186a008015082b.html

  I hope this helps. If so, please indicate the position.

  Brandon

• No network interface exists in the machine

  Hi, im using HP Pavilion dv6 - 1160ev my OS is Windows Vista 32-bit.

  I reformatted my laptop and downloaded all the dirvers but I can not install the NICs (Realtek PCI - E Fast Ethernet NIC)

  There is no network interface in the machine.

  Please, plug in the adapter on the on the expansion slot or

  Connect a cable from the ethernet network device if this computer to "Sleep Mode".

  How can I solve the problem? Thank you

  Hello bulletjuan. I understand that you have lost your network interfaces after performing a clean installation. Is this correct?

  So if you had to go to Device Manager and expand the section "Network cards" do you have something to all listed? If this isn't the case, looks like you had bad drivers, or they somehow don't settle when you reinstalled all your drivers.

  Try to install the ethernet driver once more. Here is a link to download.

  If it works, I suggest running HP Support Assistant to ensure that you have all the drivers updated, once you have an internet connection.

  Let me know the result of this; have a great day!

• Latitude C600 modem/network interface not found in XP Pro

  I have a Latitude C600, PIII 850 MHz, 256 MB of Ram.

  The operating system is Windows XP Pro sp3, 32-bit.

  My problem is that the network/modem card on board do not work and are not present in the Device Manager.

  Some other positions mentioned to install the chipset drivers, XP pro does not require not the drivers of the C600 chipset, and I found that the only offered on the site of the drivers/Dell support are for Win 2000.

  Dell support site suggests that work on board network/modem card, but I've not seen this yet.

  I am currently connected to the internet using a Xircom 10/100 Nic/modem card in the pcmcia slot, but I would like to have a card wireless here instead and use the integrated to an Ethernet network interface.

  I also posted this on the category of computer laptop-general hardware.

  Any input will be appreciated,

  Thank you

  A. Einstein

  
  

• Are virtual network Interfaces, vSwitches?

  Hi all

  I read the following document http://www.VMware.com/files/PDF/dmz_virtualization_vmware_infra_wp.PDF

  And on page 7, where it says 'Set Layer 2 Security Options on virtual switches.
  Protection against attacks such as data snooping, sniffing and MAC spoofing by disabling the promiscuous mode, change MAC address and forged the capacity of transmissions on the virtual network interfaces. »

  How to interpret virtual network interfaces? Those are the vSwitches or group of ports VM?

  Thanks for your help,

  Those that are not the default values.  Change of MAC address: Rject and forged passes: rejection would be the default values.

  But before you change them - they don't automatically indicate a security problem - you need to know why they changed first.

• Network interface are not

  Hi all
  
  I'm trying to collect loads of network with sigar.jar on my Windows 7 system but sigar does not show my network interface:
  
  Sigar > ifconfig
  Miniport Wan WAN (IPv6)
  eth0 Link encap HWaddr 84:8 B: 20:52:41:53
  INET addr:0.0.0.0 mask: 0.0.0.0
  Realtek PCIe GBE Family Controller-QoS Packet Scheduler-0000
  eth2 Link encap HWaddr 00: 1a: 4 D: 57:18:1 C
  INET addr:0.0.0.0 mask: 0.0.0.0
  Realtek PCIe GBE Family Controller-PAM light filter-0000
  eth3 Link encap HWaddr 00: 1a: 4 D: 57:18:1 C
  INET addr:0.0.0.0 mask: 0.0.0.0
  Software Loopback Interface 1
  lo0 encap:Local Loopback link
  INET addr:127.0.0.1 mask: 255.0.0.0
  ...
  
  C:\Program Files\Java\jre6\bin > ipconfig/all
  Wireless network connection Wireless LAN adapter:
  
  The connection-specific DNS suffix. :
  ... Description: Network adapter on Broadcom 802.11 g
  Physical address.... : 00-0E-8E-00-38-93
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Link-local IPv6 Address...: fe80::90:984:eb50:a4ac % 11
  IPv4 address...: 192.168.0.120
  ...
  
  release of version Sigar:
  Sigar... java version = 1.6.3.82, native = 1.6.3.81
  Build 04:06 date...java=07/09/2009, native = 07-09-2009 04:00
  SCM... java rev = 80016 c 6, native = 80016 c 6
  ArchLib... sigar-amd64 - winnt.dll
  Current full domain name... AJQ6600
  Language... 2055:German (Switzerland)
  ID of Perflib lang... 007
  Current user... Kamikaze
  Description of the OS... Microsoft Windows Vista
  Name of the OS... Win32
  BONE arch... x 64
  OS version... 6.1
  Seller of BONE... Microsoft
  Version of the OS vendor... Vista
  OS data model... 64
  Cpu OS... endian bit
  Java VM version... 16, 0 - b13
  Java virtual machine provider... Sun Microsystems Inc.
  
  Is it possible that this could happen because it's a wireless interface?
  
  I use the latest version of java jre + jdk:
  C:\Program Files\Java\jre6\bin > java.exe - version
  Java version "1.6.0_18.
  Java (TM) SE Runtime Environment (build 1.6.0_18 - b07)
  Java for 64-bit Server VM (build 16, 0 - b13, mixed mode)
  
  I also tried with 32-bit jre + jdk, but the result was the same.
  On another system of Win 7 x 64 it worked with a wired interface.
  
  Moreover, it is a nice tool for java development ;-)

  Thanks for the report Grave_Jumper.  As Mirko has pointed out, we have corrected the problem, followed here:
  http://JIRA.Hyperic.com/browse/Sigar-205

  The binaries are also available with the fix:
  http://Hudson.Hyperic.com/job/Sigar-1.6-x86-Winnt
  http://Hudson.Hyperic.com/job/Sigar-1.6-AMD64-Winnt

• I can't see second network interface integrated through Esxi 4.0 on IBM X 3200 M2

  Hi everyone, I can't see second network interface integrated through Esx 4.0 on IBM X 3200 M2, I installed and configured a first NIC and the third card PCI-express NETWORK Broadcom NetExtreme without any problem. Above their Esxi platform, I have installed two operating systems comments, but I need the second network adapter for vmware management. Now, I use the first network interface integrated to do this, but is not quite secure. I can't reinstall ESX because this system is in production.
  I have read the information, but I can't understand how do.

  Thanks, Claudio

  Welcome to the community,

  I checked the compatibility of your equipment with ESXi4.0 and result in not supported. (Check in HCL )

  IBM	IBM System x 3200 M3	Intel i3/i5 Clarkdale series	ESX 4.1 U1 4.1 4.1 U1 4.1 ...
  IBM	IBM System x 3200 M3	Intel Xeon 34xx series Lynnfield	ESX 4.1 U1 4.1 4.1 U1 4.1 ...

  Can you post here a model of all the network cards?

  Thank you

  Please, do not forget the points of call of the "useful" or "correct" answers

  Mauro Bonder - moderator

• Director of the laboratory, adding new network interface

  Hello. I have a certain virtual machines in a workspace of LM and I would like to add another network interface. I have undeplyed the machine and it gives me the ability to add a new interface, however the interface I just added does not appear. How can I add this interface to a virtual machine that has already been added to a workspace?

  Looks like what you're trying to do is simply add a NETWORK adapter to a virtual computer in a configuration. It is fairly common and is detailed beginning on page 49 here http://www.vmware.com/pdf/lm30_users_guide.pdf. Let me know if it helps.