Compaq CQ58: Update button wireless

I got an update for the wireless button but I don't know if it's legitimate, also in Device Manager which category the next generation wireless button?

draph91 wrote:

... also in Device Manager which category the wireless button is?

Hello

As shown:

Kind regards.

Tags: Notebooks

Similar Questions

  • Realtek ethernet error code driver 35, Compaq CQ58, Windows 8.1

    Hello.

    I have a new laptop Compaq CQ58-353EM. It came with preinstalled system (Windows 8). Subsequently, I installed Windows and HP updates.

    The problem I have is with the Realtek PCIe FE Family Controller (ethernet). In Device Manager, it is represented by a yellow triangle with an exclamation point. In the State of the device, it is stated: your computer's system firmware does not include enough information to properly configure and use this device. To use this device, contact the manufacturer to obtain a firmware or an update of the BIOS of your computer. (Code 35).

    Laptop has everything system and hp updates installed.

    I have tried the following to resolve the problem:

    -2 versions of various bios (F.26 and F.25).

    -several add/remove/reinstall the Realtek drivers

    -2 different versions of Realtek drivers: 8.3.730.2012 and 8.20.815.2013 (extract from the Realtek site).

    Ethernet works OK on Ubuntu.

    Any suggestions or solutions to this problem?

    New test BIOS

    CQ58 Notebook PC and HP 655

    Updated HP Notebook System BIOS (AMD processors)

    Version:

  • button Wireless: wlan disabled or to start again?

    Hello!

    I have a specific question to ask: If you turn off your connection Wireless button wireless for laptop hp (physical button on the top of the keyboard), after windows restarts wlan stay off or back on?  I ask because I advised someone to turn off wifi in this way using the ethernet cable and would like to know if it is right. I do not know the specific model, I think is a compaq it a few years ago. By pressing the wireless button it became orange and the system bar say has been disabled but I don't know if it is permanent or if restarting of the computer back on.

    Thank you

    Hello

    The wlan will remain off even after the restart and then turn not again until that key wireless.

    Kind regards

    DP - K

  • laptop Compaq CQ58: id of failure to the dst short hard drive RGF0R0

    my notebook Compaq CQ58 3 year, husbands, froze and wouldn't respond, after a few hours I force it down by pressing the power button, when I tried to start it up again once he went int automaticic repair, it took more than 24 hours.

    but the computer continues to freeze and go into the auto repair each time and was unusable.

    I don't have a recovery disk, none came with the computer and stupidley has not created a when the computer was new. being the only other computer that I have a windows vista I could not create one on this machine.

    As their was anything important stored on the computer I decided to reset the computer hoping that would solve the problem.

    I followed the instructions and the computer seems to be going through the motions to reinstall when he got stuck in a loop of

    the HP points logo swirling

    a popup with the date and time and please wait

    a white screen with the top of the window cmd at the bottom left of the screen

    back to points logo and swirling HP

    a popup with the date and time and please wait

    a white screen with the top of the window cmd at the bottom left of the screen

    After 48 hours I force crashed computer

    I ran the race test that everything happened except the short DST hard drive

    Falure ID: RGF0R0 - 69781:-MFKT1F-60WU03

    This means that the hard drive needs to be replaced and if so should I also a recovery disc, the laptop is out of warranty

    Thanks in advance for any help

    Fiona-s wrote:

    I ran the race test that everything happened except the short DST hard drive

    Falure ID: RGF0R0 - 69781:-MFKT1F-60WU03

    This means that the hard drive needs to be replaced and if so should I also a recovery disc, the laptop is out of warranty

    Thanks in advance for any help

    Hello Fiona-s,

    Thanks for posting in the Forum of Support HP!

    I'm afraid that the HARD drive has failed - the question is material one and all simply restore/reinstall will not solve it. Yes, you need to replace the HARD disk new or better with the SSD. SSDS are up to 10 times faster than hard drives:

    > http://ocz.com/consumer/ssd-guide/ssd-vs-hdd

    > https://en.wikipedia.org/wiki/Solid-state_drive

    There are more than 100 manufacturers and sellers SSD, but personally, I would choose Samsung, Intel, Toshiba, or OCZ ones.

    Microsoft Windows 7, 8.1, and 10 have supported for SSDS. Vista and XP - no

    You will need a recovery media to restore the windows once you have installed the new SSD or HARD disk.

    You can get possible by contacting HP Support. Here's how:

    > http://support.hp.com/us-en/document/bph07143

    > http://www8.hp.com/us/en/contact-hp/contact.html

    > http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html

    Feel free to post if you have any other questions.

  • Compaq CQ58-353EE: CQ58-353EE lack of PILOTS

    Hi all!

    Unfortunately, I have not found any drivers for "Compaq CQ58-353EE", about "Windows 7 (32bits)".

    I looked for the following drivers:

    -Bluetooth controller

    -PCI device

    I'll be happy if someone helped, thank you very much in advance!

    Hello:

    For the PCI device, download and install the driver first on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=15&PFID=25&level=4&Conn=3&DownTypeID=3&GETDOWN=false

    What model of wireless card your laptop there?

    Who determines what bluetooth driver, you must install.

  • Compaq CQ58: Nothing works

    Hi guys

    I have a laptop Compaq CQ58 and I tried all the links but nothing works. …
    no Ethernet controller
    No network controller
    No pci devices
    no controller communication simple pci
    No sm bus controller

    Please help its urgent

    PCI\VEN_8086 & DEV_1E3A & SUBSYS_1854103C & REV_04
    PCI\VEN_8086 & DEV_1E22 & SUBSYS_1854103C & REV_04
    PCI\VEN_10EC & DEV_5229 & SUBSYS_1854103C & REV_01
    PCI\VEN_10EC & DEV_8136 & SUBSYS_1854103C & REV_05
    PCI\VEN_168C & DEV_0032 & SUBSYS_1838103C & REV_01

    Hello:

    Use the W7 32-bit drivers for the HP 2000 t - 2A 00... except the BIOS and firmware files.

    http://h22207.www2.HP.com/us-en/drivers/selfservice/HP-2000-2a00-notebook-PC-series/5259212/model/5275371

    First install the smbus controller driver and restart.  This, to the Driver and Intel Chipset Installation Utility.

    Ethernet controller: install the Driver Realtek Local Area Network (LAN)

    network controller: install this driver:

    This package contains the installation package driver for wireless LAN Qualcomm Atheros AR9000 controller series in the laptop models running a supported operating system.

    File name: sp63802.exe

    PCI device: install the Realtek card reader driver

    PCI simple communication controller: install the Driver Intel Management Engine Interface (MEI)

  • Compaq CQ58-201SU

    Hello

    I have a compaq CQ58-201SU.

    What happened:

    I tried to reinstall windows. Current vesion was Win8.

    New Windows disk is Pro 8.1.

    It gave me an error message saying the following:

    "Windows cannot be installed to this disk. the selected disk is a MBR partition table. The EFI, Windows system cannot be installed on GPT disks.

    I was about to download Gparted on a USB key to set the partition type.

    Tried it once more just to make sure it wasn't a mistake.

    Laptop computer willl no longer starts or won't let me not even get into the BIOS.

    Caps and screen black lock blinkig twice between breaks. -(HP FAQ thead, it is an indication for corrupted BIOS).

    Tried the Reset Hard Power. (Remove the battery, press and hold the power button for 15 sec, put the battery back on, alternative current summer)-did not work.

    I tried a BIOS reset. (Press Windows key + B first and then press the button for a second, while now the other keys, then release them together) - tried several times, nothing happens.

    Someone has an idea, what do I do next?

    I solved my problem by following these steps.

    Removed the battery.

    Removed the two rear panels covering the WiFi card + RAM and HDD bay.

    The deleted BIOS battery.

    WAITED 5 minutes.

    Put everything back together.

    Startup. > Get message to reset the BIOS.

    Reset.

    Now, everything is normal.

  • Compaq CQ58-bf9WM: upgrade memory for Compaq CQ58

    Compaq CQ58-bf9WM came with 2 GB of memory and 1 slot.  I've recently updated 8 to 8.1 windows (I think its 64-bit, but it's the original operating system updated) and AMD inside.  What is the maxium memory slot amount single will execept.  Care say he'll take 8 GB also said there are 2 memory slots (2 blocks of 1), but there is only one (based on Visual information items).  Please notify.

    Hey @fridge411,

    I recommend always go against what is in your textbook as recommended. But sometimes these things just work without any problem. I wouldn't you not waste your money.

    Thank you.

  • Cq58 Compaq: Compaq CQ58 - device to boot not found

    Compaq CQ58

    Hello

    When you turn on I get

    Not found boot device

    Please install the operating system on your hard drive.

    Hard drive (3f0)

    f2...........................

    visit hp.com...

    And nothing else

    Then I do the "F2" as follows:

    UEFI V 1.6.0.0 - BIOS

    visit...

    ... Past the memory test
    ... Past HD disk check

    I go to f10

    > F9 message load setup defaults > Yes > f10 save and exit > Yes

    No improvement even if there is a life in there cos the disc or the fan turns

    I think the next step is to redo any os USB

    Cannot find links suggested to reboot on HP site - they go absolutely nowhere, unnecessary.

    This is my son's laptop computer

    It loaded windows 10

    a windows 8

    do not know what he was doing, but he said it worked on 10 for a while.

    Why microsoft allow minors to mess up so bad? In any case...

    I don't know if he'll want to restore as windows8 or 10

    I don't know if it's 32-bit or 64-bit in any case

    Who tells us of the f10...

    third line up always suggest windows 8?

    Here is the capture of the f10 camera

    All ideas

    No tellings off the power. No closing the stable door once the horse has bolted.

    Means and just before useful suggestions please.

    Thank you very much.

    Concerning

    Wilf's dad

    Hello

    No matter if update 8 - also long as 10 Windows activated successfully, you can use the "clean installation" method

    It is possible that if the machine had just been "updated", the hard stop interrupted files system updated and this can lead to this kind of question.

    As a general rule, a clean installation of Windows 10 has less problems problems/performance than the upgrade from a previous version of Windows.

    Kind regards

    DP - K

  • Update my wireless network device does not work after installation of Software Distribution Service 3.0

    After the installation of Software Distribution Service 3.0 update my wireless network camera does not work how do I uninstall Software Distribution Service 3.0

    How did you receive the update?

    Was it via Windows Update or Microsoft Update?

    Before the changes are made to your computer, the system restore points are made. This is so that you can go back in case an update causes problems.

    Follow these steps:

    1. click on the Start button

    2. click on accessories

    3. click on system tools

    4. click on system restore

    5. click on next

    6. in the calendar that appears, select the one which refers to Software Distribution Service 3.0 and click Next

    After the collection of certain data, the computer will restart, and the update will be gone.

    Hope this helps

    Post back if necessary

    ___________________________________________________________

    If this post can help solve your problem, please click the 'bookmark' or 'Yes' to this message button. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • Install HP Compaq CQ58-d04SM bluetooth can´t

    I bought a Compaq CQ58-d04SM PN E4Q06EA #BED and install Win 8.1 Pro. I can't install the bluetooth driver.

    In the Device Manager in the properties of the controller Bluetooth is written:

    The drivers for this device are not installed. (Code 28)

    There is no compatible driver for this device.

    To find a driver for this device, click Update driver.

    I downloaded two drivers for the Hp http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4158&lc=en&cc=us&dlc=en&sw_lang=&product=5404... website

    If I install Qualcomm Atheros QCA9000 series Bluetooth 4.0 + HS pilot error message is: "the device may not be present or could have been ejected/disconnected from the system. Insert or reinsert now', or

    If I install the software Mediatek Bluetooth driver Compaq will restart before the end of the installation.

    Where can I find a driver?

    Thank you

    I found what the problem with my bluetooth. It's a Bluetooth support service. I have to go to start - run - Bluetooth support service - Services and to assign to this service manual automatic starting and I start this service. Then I install Ralink (Mediatek) bluetooth driver (this time there is no restart before the end of the installation) and that s all. Bluetooth works.

  • Compaq CQ58 computer 301SA laptop does not connect to 50Ghz band on router

    My laptop does not connect to the band 50Ghz on my router dual-band. I know that my router Netgear dual band diffuse 24 and 50 Ghz, but the laptop only shows the 24 Ghz band depending on availability.

    I have a Compaq CQ58 301SA Notebook PC, Windows 8 (64 bit OS).  It has a Ralink RT5390R 802 11bgn network adapter and a Realtek ethernet network adapter. I use the laptop wireless, for example using the Ralink connection and it connects easily to the 24 GHz band, but I want to broadcast TV programs and movies smoothly, for which, I understand that the 50Ghz band is preferable. I pay my ISP (Virgin Media) for a connection to Super-fast broadband but my laptop seems to be limited to the 24 GHz band. Seems to be the case if I work with the adapter Ralink wireless or wired with Realtek ethernet connection.

    This problem can be corrected? If so, how? What I have done research on the web, the problem seems to be network adapters. Can they work on the 50Ghz band? Or do I need to download another adapter (if so, which?) Or use an adapter external network I plug into a USB port?

    Driving me crazy...

    Hello:

    The Ralink RT5390R 802 11bgn is a map of the only band (2.4 GHz) only.

    Whenever you see a labeled bgn wireless card, it is a single band card.

    Cards labeled dual band abgn or agn.

    The maintenance manual (Chapter 3, page 19) does not indicate that any internal dual band card is supported, so you would probably have to go with an external usb dual wireless adapter.

    http://h10032.www1.HP.com/CTG/manual/c03593268.PDF

  • No WIN7 DRIVERS for HP Compaq CQ58-249SG

    Hi, I miss some Win 7 drivers for a new HP Compaq CQ58 249SG purchsed. I finished installing Win7 (previously was only BACK on this subject). See below for screenshots of the hardware ID missing drivers:

    You are the very welcome.

    Sometimes happened to me also, and do to get around that is to not try to install all the updates in a big piece.

    I'm about 20 at a time.

    Try the network directly from Realtek driver.  a 2nd on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

    If this does not work, then it must.  a 2nd on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

  • How is it that after I put 41.0b1 as a 'update crucial"my youtube DVDVideoSoftware updated buttons are disabled?

    How is it that after I put 41.0b1 as a 'update crucial"my youtube DVDVideoSoftware updated buttons are disabled?

    Maybe it's because the add-on is not longer supported by the latest version of Firefox. You can try to see if a new version of the add-on is available and can be downloaded. If this is not the case, contact the developer so they can inform you of alternatives or when the add-on is working again.

    Thank you!

  • No update button

    Airport warn me of an update for time capsule, but there is no update button...?

    Hold down the option key and click on the version, the vehicle's currently on summary page... He should then list the TC available firmware versions available and you can choose it then.

    But some people have problems from a Mac. If you have the ipad or iphone download the iOS version and use it.

    If not, tell us what your problems persist... There is a manual method.

    Re: proxy server annoy 7.6.7 update?

Maybe you are looking for