Computer does not start when connected to USB-6341

Similar Questions

• Computer does not start when PCI-6509 is installed.

  We have a "shoe box" Advantech (System specs are listed below) and try to install a digital I/o card of National Instruments PCI-6509. Once we install the digital IO card, the computer will not start. The computer does not even a MESSAGE. We know that the digital I/o card is functional because we ran the same card on several different machines. We also tried the card on other Advantech computers with the same brand and model without success. What should we do to get the card working on Advantech computer?

  Advantech computer scpecifitaions:
  Pentium 4 with backplane passive 256 MB DDR memory, Windows 2000,.

  Thank you for your help,
  Tim Elsenbroich
  Software engineer
  Wisconsin electronic systems, Inc.
  Phone: 262-554-1211
  FAX: 262-554-1797
  E-mail: [email protected]

  We hung a spare ATX power supply to backplane of the computer, the computer booted right up and the PCI-6509 worked perfectly. I contacted the manufacturer of the computer and am waiting for prices on ATX supplies getting in our computers instead of the TA.

  Thank you for all your help.

• G5 Powerpc does not start with connected external USB

  Core PowerPC G5 2.3 duel starts when I have my usb external 500 GB on drive but it works perfectly well if I boot

  with it goes off and then start and turned on after my mac started in Leopard 10.5.8 external USB is a 500 MB TARGA

  I have a WD elements 2. TB disk connected as well and I have no problem with it, it's a pain to remember to put a stop on all the time.

  Anyone have any ideas on that.

  Drive external hard there an independent supply?

  What happens if you attach externally to a different USB port?

• Computer does not start with connected external HARD disk

  Although my BIOS doesn't look like another hard drive, when I start my computer with the external hard drive, the main computer shuts down until I have disable externally. I want to have external to back up automatically but can not have both to play well.

  Help!

  Hello

  The same thing happened on my laptop with a connected external printer.
  I was not able to turn on the laptop until I unplugged the USB printer.

  Well, I checked the BIOS which controls the start and put the HARD internal disk to the first position!
  Try this. Maybe it helps. Otherwise you will need to disconnect the external USB HDD til the operating system has started

• for some reason any my itunes on my computer does not start when I click on the itunes I have con

  even when I go to the start menu and click the itunes icon it starts

  Hello
  ·         Did you the latest changes on the computer before the show?
   
  You can follow the steps in troubleshooting the link and check if it helps.
  iTunes for Windows XP: Troubleshooting unexpected quits unexpectedly, freezes, or launch issues
  http://support.Apple.com/kb/TS1421

• my computer does not start when turned on a black screen monitor

  Computer most of the time will light up all the way and the screen remains black. If I push the power button on the monitor, you can see briefly what the screen should look like through the dark.

  What should I do to fix this?  I have Windows XP Professional

  Hi TraciLucia,

  ·         You receive an error when starting?

  ·         You see the desktop behind the black screen icons?

  Try the following.

  Method 1: Start the computer in safe mode and check the number. Report of the results.

  Method 2: Check to see if this article helps you.

  Computer stops responding with a black screen when you start Windows XP

• MapPoint 2009 does not start when connected to a network

  Hello

  I'm currently trying to install Mappoint Europe 2009 on an HP under Windows XP SP3 laptop. Previously he has worked well with no problems at all - until now. After the installation of Mappoint Euro 2009 application will only work if the laptop is not connected to a network or the DHCP client service is prevented from running by using msconfig (essentially the same thing as pulling the cable). I have now tried this on 2 different laptops and can't seem to find what is causing the problem.

  I tried to install, run as administrator and also to give the administrative user account access, but they all have the same result. As you can tell from above, I have also lived the tedious process of using msconfig and selective startup options after seeing the other messages in relation to similar problems on Win7. So far, no joy.

  At the moment the only way that the user can access Mappoint is to disconnect from everything and remove the cable - use Mappoint and then plug it back in and re-login to all new - which is not ideal.

  It seems to be a bit of a weird error then I was wondering if anyone has found this before or has any ideas?

  Hello

  I suggest you to send your query to the following link.

  http://social.Microsoft.com/forums/is/streetsandtrips/threads

• Error - Connection Internet Service does not start when try to start Windows Security Center.

  Original title: Windows security center usually run in windows XP.

  When I open the control panel and click on security, Windows Security Center indicates that it is not executed and wont run then when I try to turn it on I say error message does not start internet connection service. Also, my computer has been slowing way down lately and it takes forever to do even the simplest taskes. I just uninstall norton because my subscription ran out and then I installed MSE and malwarebytes MSE runs even slower, so I got rid of him.

  -Edit
  I also tried to use FixIt, but he said that there was an error during installation.

  Thank you. I had security work center. That's how I did it.

  I wen to your link and found that I needed to go to start-my network places - view the network (in the sidebar) connections - click Properties (click on) Local Area Connection 2 - click on the Advanced tab - click settings (skip this step if who does not appear)

  now, here, he said that there is an error and that I needed to start a process. I think it was 'Windows management instrumentation' but whatever it is, click Activate and change the startup type to automatic, and then click Start. then try to then you should do the same thing with

  • Application Layer Gateway Service
  • Network connections
  • Knowledge of the network (NLA) locations
  • Plug-and-Play
  • Remote Access Auto Connection Manager
  • Remote Access Connection Manager
  • Remote procedure call (RPC)
  • Telephony

  Then Security Center. When you press OK in the properties, you should see a small lock appears on the network connections icon. now Security Center should work.

  useful articles:
  http://support.Microsoft.com/kb/919291
  http://support.Microsoft.com/kb/827328
  http://TechNet.Microsoft.com/en-us/library/bb457029.aspx

• AiOSoftwareNPI (* .ms) the Setup program does not start when I start my computer.

  original title: AiOSoftwareNPI

  I'm having a problem with a software AiOSoftwareNPI problem (* .ms) the Setup program does not start when I start my computer.

  I know it's a Windows Installer but I don't have a disc with this route. I even tried to reinstall the windows xp disk and it does not work, I still

  get the same box when I shutdown and restart. The box allows me not to leave him continues to appear.

  Thank you

  Ms. C

  After doing a Google search for AiOSoftwareNPI and followed by the reading of many different threads in various forums, I found that it is for drivers for an HP all-in-One printer.

  You have an HP printer?

  If so, the usual suggestion was to place your HP printer disk in your CD/DVD drive and restart. After reboot would be installed the necessary files and the pop - up would more appear at startup. I don't know if it will actually work because in all the discussions I've read, none of the original poster never responded by saying that it worked or not.

  The next most common suggest was to download the latest driver for your HP printer to your version of Windows (including at the level of the ILO) and install it. Yet, not a single original poster has responded.

  In fact, if you have an HP printer I suggest to visit the web site of HP support below the link to get the latest drivers and their installation. Visit the support for the correct installation method and if you need to remove the old driver first. You can also visit the communities of Support HP for assistance (a link for communities is also on the next page).

  Support HP & drivers
   http://WWW8.HP.com/us/en/support-drivers.html

  Kind regards

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• I have Windows 7, my computer does not start. I did the Startup Repair and he won't fix it. I did the system configuration information

  I have Windows 7, my computer does not start. I did the Startup Repair and he won't fix it. I did the system configuration information. and that did not help. What to do now? The comment of Bios makes me fear that it could damage my computer forever. What should do? Help, please

  Hi Alan,

  Thanks for posting your query in Microsoft Community.

  I understand that the computer does not restart even after running Startup Repair and I will be happy to answer your query. I appreciate the efforts made to try to make it work. Let me ask you;

  • How do you run the Startup Repair?
  • Do you have Windows 7 repair disc?
  • Remember to no particular change in the computer before the show?
  • Have you plugged an external equipment, except the keyboard and mouse?
  • You are able to start the computer in safe mode?
  • What is the brand and model of the computer?

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  There could be several reasons why he's not leaving including hardware as well. In addition, it could be because the master boot record (MBR) has been damaged. When you try to use the Startup Repair tool to repair the MBR, the Startup Repair tool indicates that no problem was found or it does not work yet.

  If you have any connected USB flash drive or other external devices connected to the computer, if you please, remove them and try to run the Startup Repair tool.

  If you haven't tried using Windows 7 repair disc, you can try the following:

  1. Insert the Windows 7 disc
  2. restart your computer
  3. When asked if you want to boot from your DVD player, do it.
  4. Select your language, click Next.
  5. click on repair your computer
  6. Select the operating system you want to repair.

  You can also perform the system restore by selecting the restore point when you think it worked very well. System Restore, choose advanced options using the disc.

  Important: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed after this date are deleted.

  I also recommend to contact the computer manufacturer to get the done diagnostic equipment.

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• My computer does not start a player - A does not exist and does not recognize my hard drive.

  My computer does not start. I tried to solve a problem with the disappearance of CD and DVD ROM drives, I unplugged then replugged cables connecting readers to the motherboard and when I rebooted, it told me to insert a bootable media in the floppy drive. I don't have a floppy drive. Before I tried to repair CDs and DVDs, my directory showed an A/floppy disk, because it seemed weird, yet benign, I don't think many, until my BIOS could not find my hard drive. It offers my USB drives and there is no such thing as a floppy drive to boot from. Help?

  If the drive is not detected in the bios, and I guess you actually mean the bios screen, then the drive has failed or the motherboard connections has a problem.

  Once in the bios screen try to reset for fail safe defaults, reboot, see if that makes a difference for the drive detected in bios

• Pavilion dv7: my Pavilion Dv7 laptop computer does not start the system recovery options

  So it told me to turn my phone off, then back on whilist cling the key F11. But when I do it my is laptop beep loud noise and rest on the logo hp, whilist is on this screen is says 'System recovery F11' in the lower left corner and does not move on the screen, how to fix this?

  Hi @Jaytee2 ,

  Thank you for visiting the Forums HP's Support and welcome. I read on your HP laptop and get a blank screen or black at startup. Try perform a reset.

  When you perform a hard reset note remove all USB devices. Disconnect all non-essential devices.

  Here is a linkto computer does not start for Windows 7.
  
  Here is a documentthe performance of a Windows 7 system recovery.

  Do you have records system for this laptop?

  I'd be happy to help you if necessary. How can I find my model number or product number?

  Please let me know.
  
  Thank you.

• Computer does not start after running the utility Boot Lenovo.

  Hello
  I replaced the power supply with a CX550M of Corsair, increased memory by exchanging the 4 GB to 8 GB for a 16 GB total, I added a hybrid 2 TB Seagate HDD and all worked fine until yesterday, about 1 month.
  Yesterday, I decided to run all the tests of the Lenovo startup disk and after that I restarted, the computer does not start.
  When I press the power button, the fan starts and it stops after 3 or 4 seconds and nothing happens, the monitor says no signal, I removed the external USB disk and printer, I reoved the second drive and the same thing heppens.
  Any idea what this problem could be? Would it be a bad power supply?
  Thank you

  Mario

  Resolved, I erased the memory CMOS, moved to following ankle boot, back up the cmos.

  Thank you

• computer does not start after installing video card

  I, m new here so please bear with me.  I have a PC HP Pavilion Media Center TV (m7434n) I'm trying to replace the video card (Nvidia GeForce 6200SE with Turbo Cache) in. I am trying to replace it with a Nvidia EVGA 8400GS. I delete all the nvidia drivers, make sure that the pci-e card is used in the implementation. I have then to remove the old card and install a new one. When I try to start the computer, fans turn on but that's all.  There is nothing on the monitor.  The computer does not start. I replaced the power supply bestec 300 watts with a new antec brand 430 watt power supply.  When I reinstalled the old video card, the computer starts ok. I tried to replace the video card with an ATI Radeon HD5550 too and it's the same thing (the computer would not start), reinstall the old card and it starts up fine. Any help would be greatly appreciated.

  Gary,

  You may have a compatibility issue with the ATI HD 5550 and 2006 PC model.  I've seen other posts where ATI 5xxx video card did not work in older HP PCs.

  When you are referring to the installation of the older video card do you mean going back to the integrated video card?  Moving the video cable to the card installed?

  Install the NVIDIA 8400GS and connect the video cable. Now follow the instructions for clear the CMOS.