conditional of the loop will not control read in a business event

Similar Questions

• Event case + while loop (the controls inside the loop will not be updated)

  Ok. I don't know what I'm doing wrong.

  But when I press Start, I can't move the slider control.

  All the obvious errors here?

  Bob123456 wrote:

  But when I press Start, I can't move the slider control.

  Your event is set to lock the front until the end of the event. This means that you are in a bind, because the event cannot be completed until the button is pressed, which can happen because the FP is locked.

  Quick "bandaid fix" would be to uncheck this option in the configuration of the event. Not recommended!

  You should never place interactive code within the structures of the event. Restructure your code accordingly. See state machines, for example.

• printer and files of the device will not control panel open

  I have problems with a HP Officejet 5600 307N.  Unable to get printer and folder of device to load from Control Panel.  Any suggestions?

  Open the command prompt

  type in
  net stop spooler and press enter
  then type in
  net start spooler and press enter
  Then, go to the Printers and devices folder.

• Loop will not stop when you press the stop button

  Hello

  I have a LabVIEW program that includes a number of loops, but one of my curls (which surrounds a series of functions "Write TDMS") has a Boolean stop that transmits a signal through two GOLD and functions in a control of the loop (see aea of interest). My problem is that when I press the button stop the loop will not stop and will continue to save and write data that I didn't need a file.

  Could someone please help with this?

  Kind regards

  Aaron Broady

  
  

• I sent an email to someone by mistake earlier. How can I recall a message if the person has not yet read?

  I sent an email to someone by mistake earlier. How can I recall a message if the person has not yet read?

  Hello sanjaykaul, which would not be possible - once an email leaves your mail server is therefore more under your control.

• Why do I get the jqsnotify.exe - Application Error Application error. The memory could not be read?

  Why I get this error message every time I opened Firefox saying: jqsnotify.exe - request error and then at the end of the line, he says: the instruction at '0x5ff3d322' referenced meory to '0xe41203c3 '. The memory could not be "read". Click on OK to terminate the program.

  This has happened

  Each time Firefox opened

  == I recently renewed and installed CA Security Suite and Firefox uninstalled and reinstalled again.

  http://www.java.com/en/download/help/quickstarter.xml - what is Java Quick Starter (JQS)? What is the advantage of running JQS? -6.0

  Disable Java Quick Start extension: Tools > Addons > Extensions
  Control Panel > Java > Advanced tab > various > Java Quick Starter (disable)

• After the upgrade to OS 10.11.2, Mac Mini is so slow that it can take an hour to operate and the printer will not scan.

  After the upgrade to OS 10.11.2, Mac Mini is so slow that it can take an hour to operate and the printer will not scan.

  When you see a beachball cursor or the slowness is particularly bad, note the exact time: hour, minute, second.

  These must be run as administrator. If you have only one user account, you are the administrator.

  Run the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  The title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  Each message in the journal begins with the date and time when it was entered. Highlight date back to the time you noted above.

  Select the messages entered since then until the end of the episode, or until they begin to repeat, whichever comes first.

  Copy messages to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost all this is useless to solve any particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name, may appear in the log. Anonymize before posting.

  When you post the journal excerpt, an error message may appear on the web page: "you include content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• SR400 while the loop does not work

  Hello

  I'm using LabVIEW for control SR400 through a GPIB card.

  I use SR400 to count the number of signal in a second, wait 0.05 s, then again count the signal once, wait 0.05 s once again, and so on.

  However, the while loop didn't iterate. When I started the program, it is only once.

  In execution of highlight mode, when an iteration is finished, he waited a long period starting the next. In normal mode, it doesn't have to iterate.

  Also when I clicked the stop button, it's been clicked. However when I wrote a very simple program, the stop button worked normally.

  In any case the button issue is not very important. I don't care that the program iterates forever or not. I just want to iterate.

  I searched the jury and had not could not any related problem.

  Is it better to attach my VI? The VI is in my computer lab.

  Thank you very much!

  This code just feels bad.

  (No real management mistakes, deep, stacked sequences FOR lines that are wired to iterate through only once, controls on the right and right to left, wiring weird code on average the last 10 items (Hint: means ptbypt with a length of 10 sample he would!).) If you want to use the wire of the error, the sequences would not even necessary)

  If the stop button does not reset, it means that the iteration of the loop does not terminate. It can fill in only if the two structures of the sequence ends.

  Have you tried running in execution, emphasizing fashion while looking at the diagram? Probably one of the communications is at a standstill. For example, the instrument sends really 6 bytes at the end? When you set the overall timeout and what is it?

• Office Jet 6700 will not control panel scan. ideas please

  Office Jet 6700 will not control panel scan. ideas please, everything else works fine and happy with printer

  Have you tried to perform a full power cycle on the system and try the analysis immediately after that everything is turned on?

  • Unplug the router all-in-on
  • Wait 30 seconds
  • Plug the router back in power and wait until it completely initialize
  • Restart the PC
  • Unplug the printer while on
  • Wait 30 seconds
  • Plug the printer back in direct power

  So, have you tried to disable your firewall and protection scan from the front panel of the printer?  Sometimes a firewall service will see the printer as a threat and block incoming traffic.  However, based on the analysis of gets it PC around as she reaches out to the device, rather than the reverse.

• My laptop sees my Xbox 360, but the 360 will not connect to the top of the Tower

  I have a crossover ethernet cable

  I tried everything, but the 360 will not find the network,

  It saying that he "cannot obtain an IP address form the router or modem.

  Your router or modem can be automatically assigns an ip address, you can try a static IP address instead

  
  

  DHCP Server IP address form

  
  

  Help please

  
  

  
  

  Hey tons-of-pleasure-101.

  You can set a static IP address on the Xbox 360 by going to network settings and then manually enter an IP address.
   
  (1) type cmd in the start search field.

  (2) type ipconfig/all in this window, and then press the Enter key. This will display a lot of information.

  3) take down of the IP address, subnet mask, default gateway, and name servers. Be sure to note which is which.

  (4) type exit in this window, and then press the Enter key to close.

  (5) once more, open the start menu. This time, click on Control Panel.

  6) click view the status of network and tasks.

  (7) select the settings of map on the left side of your screen.

  (8) make a right click on your network adapter and choose Properties to open the properties of this internet connection window.

  9) click Protocol Internet Version 4 (TCP/IPv4), and then the properties button.

  Until you make changes, write down the settings you see on this page. If something is wrong you can always change the settings back to what they were! You should see a point in the obtain an IP address automatically box.

  (10) choose an IP address and type in the IP address box. The ip address that you choose should be very similar to the ip address of the router. Only the last number of the ip address must be different.

  (11) put the previously found in section mask subnet mask subnet. The default gateway should enter in the default gateway box. Enter the dns servers we prevoiusly found in the two zones on the DNS server. Completely out of this menu, click OK.

  That's all you should be done.

  Once done, you must assign a static ip address for your xbox as well.
  When you're done, between the two, the only parameter that must be different is the actual IP address. The gateway and subnet mask must be the same on your XBOX and PC LAN connection.

  Refer to this:

  Can not get an IP address from your router or modem
  http://support.Xbox.com/support/en/us/NXE/xboxlive/troubleshooting/NetworkHelp_dynip.aspx

  This should be it.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• QuickBooks error message: qbw32.exe - Application error: the instruction at "0x56461f49" referenced memory at "0x02ec4360". The memory could not be "read".

  I am running Windows XP Professional Version 2002 w/SP3. QuickBooks Pro 2008 is installed on it. Whenever I close the program, I get an error message: qbw32.exe - Application error: the instruction at "0x56461f49" referenced memory at "0x02ec4360". The memory could not be "read". I have absolutely no idea of what that means. The message will only appear when it terminates the program and does not do. Any info is greatly appreciated.

  Hi stickman397,

  This error occurs during the installation of QuickBooks is damaged. To resolve this problem, follow the steps in the link below:

  http://support.QuickBooks.Intuit.com/support/pages/knowledgebasearticle/1008533

  Kind regards

  Imran M

  Microsoft technical support

• According to the set printer wizard, my new printer software has been installed, but the printer will not appear on the section 'printers and faxes '.

  You have a printer again, with installation CD. According to the set printer wizard, my new printer software has been installed, but the printer will not appear on the "printers and faxes" section in Control Panel. Model of printer - Epson XP-200.  Have a Dell, Windows XP.  Help!  Not even sure who to ask...

  What version of XP (Home, Pro, Media Center) and service pack (none, 1, 2, 3)?

  Printers and faxes is totally blank?

  Open a command prompt window (start > run > cmd > OK)
  Type the following in the black command prompt window and press enter
  spooler request SC

  You should see something like this:
  Service_Name: Spooler
  TYPE: 110 WIN32_OWN_PROCESS (interactive)
  STATE: 4 RUNNING
  (STOPPABLE, NOT_PAUSABLE, IGNORES_SHUTDOWN
  WIN32_EXIT_CODE: 0 (0X0)
  SERVICE_EXIT_CODE: 0 (0X0)
  CHECKPOINT: 0X0
  WAIT_HINT: 0X0

  What is the 'State' displayed for you?

  Open the Services applet (start > run > services.msc > OK) and scroll down to "print spooler".  The status should be started and the Startup Type should be automatic.  What are the parameters of your correspondents?  If your print spooler is stopped, you can try to launch it by clicking on the link, but I suspect that it stops again.  Please report the results of your efforts.

• ehRecvr.exe - Application error the instruction at "0x53801d4f" referenced memory at "0x00000000". The memory could not be "read".

  Message MSVidCtl broadcast system receiver: ehRecvr.exe - Application error the instruction at "0x53801d4f" referenced memory at "0x00000000". The memory could not be "read". This error will not go away and I can not disable or delete the file. How can I stop it?

  Hi SteveGHowe,
   
  -Remember to make changes to your computer after that this problem started to happen?
   
  Try to disable and re-enable the Media Center service and check:
   
  a. Click Start. Click run.
  b. type: services.msc and press ENTER.
  c. find Service Media Center Receiver.
  d. right-click on the service and click on stop.
  e. restart the computer and follow the same steps of 'a' by 'c '.
  f. now right-click on the service and click Start.
   
  Also, try the steps listed in the following link:
   
  Troubleshooting steps I use for Media Center component registration failure error

• Startup message: black screen error box with the instruction at 0x7468a9df referenced memory at 0 x 000000000. the momory could not be read.

  Original title: What happens when I turn on my computer. Why? black screen with error box the instruction at 0x7468a9df referenced memory at 0 x 000000000. the momory could not be read.

  When I turn on my computer, get this Windows logon error message: logon UI.exe

  black screen with error box the instruction at 0x7468a9df referenced memory at 0 x 000000000. the momory could not be read.

  Hello, help,

  Unplug all devices - printer, speakers, digital camera, etc...  The attempt to start start

  You are able to go in Mode safe mode with networking?    Restart and the logo of computer, start typing F8.  See if you can download this file and run a scan complete for malware.

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&id=16

  If the auditor of applicable system files, run

  Right-click on command prompt and select run as administrator

  Type SFC/scannow

  Note: there is a space between SFC and /scannnow

  Press enter

  It will take a few moments for the analysis to be performed.  You can find the paper pressing the Windows flag key + r to open the run window

  Type %windir%\Logs\CBS

  Press OK

  Search for ""impossible to repair corrupt files"Note all corrupted files that are not repaired."

  Try to extract the file to your recovery CD.  It is possible Logonui.exe has corrupted.

  http://blog.NirSoft.NET/2009/09/17/how-to-extract-missing-system-files-from-the-DVD-of-Windows-7vista/

• Try to burn a CD. The system will not recognize the blank disc or let me burn__

  Try to burn a CD. The system will not recognize the blank disc or let me burn... says there is no disc inserted

  Hello

  Have you tried to close all programs and then insert the disc? Restart the 1st and then try it.

  If no joy:

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.