BIND THE SINGLE TUNNEL ON ASA IP ADDRESS

Similar Questions

• I can weight of the IPSec Tunnels between ASAs

  Hello

  Remote site: link internet NYC 150 MB/s

  Local site: link internet Baltimore 400 MB/s

  Backup site: link internet Washington 200 Mb/s

  My main site and my backup site are connected via a gigabit Ethernet circuit between the respective base site switches.  Each site has its own internet connection and my OSPF allows to switch their traffic to the backup site if the main website is down.  We are opening an office in New York with one ASA unique connected to 150 Mbps FIOS internet circuit.  We want to set up an IPSec tunnel on the main site and the backup on the remote site, but want the remote site to prefer the tunnel in Baltimore, except if it is down.

  Interesting traffic would be the same for the two tunnels

  I know that ASA cannot be a GRE endpoint.  How can I force the New York traffic through the tunnel in Baltimore as long as it works?  An IPSec tunnel can be weighted?

  Thank you

  It is not in itself weighting, but you can create up to 10 backup over LAN to LAN VPN IPsec peers.

  For each tunnel, the security apparatus tried to negotiate with the first peer in the list. If this peer does not respond, the security apparatus made his way to the bottom of the list until a peer responds, or there is no peer more in the list.

  Reference.

• Configure the module of firepower ASA IP address

  Hello

  today I tried to configure the IP address of the late ASA power module. But unfortunately I failed. The firewall is in the direction of the situation and also do have not any router on the LAN. So, I stop the management interface and configure the IP of firepower on the network server management. But unfortunately I can not ping the gateway IP address that is actually one of the interface of the firewall. It is the series x 5525 firewall. So this isn't a any interface dedicated to management of firepower. It would be nice to know where I made the mistake? I recharge and recovery of the module and I consider the State as always state of recovery. So my question is looking for there is a problem with the module itself?

  Module status

  SH module

  Model serial number of map mod
  ---- -------------------------------------------- ------------------ -----------
  0 ASA 5525 - X with SW, GE, 1 GE Mgmt, AC 8 data
  IPS unknown n/a
  cxsc unknown n/a
  SFR unknown n/a

  MAC mod Fw Sw Version Version Version Hw address range
  ---- --------------------------------- ------------ ------------ ---------------
  0 f  1.0                                                2.1(9)8      9.2(3)
  ips                                                         N/A          N/A
  cxsc                                                       N/A          N/A
  sfr                                                         N/A          N/A

  The Application name of the SSM status Version of the Application of SSM mod
  ---- ------------------------------ ---------------- --------------------------
  IPS unknown current Image number does not apply
  cxsc unknown No. current Image does not apply

  Data on the State of mod aircraft compatibility status
  ---- ------------------ --------------------- -------------
  0 to Sys does not apply
  IPS does not is not Applicable
  cxsc does not not Applicable
  SFR recover not Applicable

  Config firewall Interface

  #Interface IP-Address OK? Method State Protocol
  GigabitEthernet0/0 10.101.106.115 YES CONFIG upward upwards
  GigabitEthernet0/1 10.106.106.115 YES CONFIG upward upwards
  GigabitEthernet0/2 10.103.254.254 YES CONFIG upward upwards
  GigabitEthernet0/3 10.0.210.254 YES CONFIG upward upwards
  GigabitEthernet0/4 10.100.254.254 YES CONFIG upward upwards
  GigabitEthernet0/5 10.107.253.115 YES CONFIG upward upwards

  #interface GigabitEthernet0/1
  Speed 1000
  full duplex
  nameif Server
  security-level 70
  IP 10.106.106.115 255.255.0.0

  Fire power management configuration

  Host name: 1 Swiss francs
  Configuration Management Interface

  Configuration IPv4: static
  IP address: 10.106.251.253
  Network mask: 255.255.0.0
  Gateway: 10.106.106.115

  IPv6 configuration: Stateless autoconfiguration

  Configuration of DNS:
  Domain: XXX.local
  Search:
  XXX.local
  DNS server:
  10.101.251.2
  10.201.251.2

  Any help will be greatly appreciated.

  Thank you

  Sari

  Sari,

  Even if there is not a physical module services fire power management port, it uses Management0/0 port to connect to the module of SFR.  If you like on the same VLAN as your server VLAN on the SAA plug Management0/0 port on a switch that is sharing the network server VLAN and give the module SFR an IP address on the same subnet.

  Make sure that you remove the statement under interface Management0/0 nameif. Here is an example:

  interface Management0/0
  management only
  No nameif
  security-level 100
  no ip address

• Cisco ASA ruled out a specific ip address of the split tunneling

  Hello

  I need help with a question on the split Tunneling Configuration.

  I have need exclude split tunneling networks already configured a specific ip address.

  This is my setup:

  Split_Tunnel list standard access allowed 192.168.0.0 255.255.0.0
  Split_Tunnel list standard access allowed 10.0.0.0 255.0.0.0

  attributes of Group Policy GroupPolicy_Anyconnect_Access_Exception_1
  WINS server no
  Server DNS value xxxxx xxxxxxx
  VPN - connections 3
  VPN-idle-timeout 480
  VPN-session-timeout no
  client ssl-VPN-tunnel-Protocol
  value of group-lock Anyconnect_access
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Split_Tunnel
  field default value xxxxx
  Split-dns value telefonica wh.telefonica cic.wh.telefonica telefonica.corp t380.inet
  mailar.telefonica.Corp mailar.telefonica.com tefgad.com telefonicaglobalsolutions.com
  telefonicabusinesssolutions.com

  I need to exclude the split tunnel, IP 10.0.0.50, my question is, if I change the list access deny this IP, the supplementary tunnel will exclude the period of INVESTIGATION.

  example:

  Split_Tunnel list standard access deny 10.0.0.50 255.255.255.255

  Split_Tunnel list standard access allowed 192.168.0.0 255.255.0.0
  Split_Tunnel list standard access allowed 10.0.0.0 255.0.0.0

  BR,

  Fidel Gonzalez

  Hi Fidel,

  Yes, it should work; as in your example deny 10.0.0.50/32 sholud exclude the traffic in the tunnel.

  I tried in my lab, and in my case, access-list is:

  split_1 list standard access denied the host 10.2.2.250
  split_1 list standard access allowed 10.2.2.0 255.255.255.0

  And it worked he excluded the 10.2.2.250 host.

  The screen shot of the AnyConnect added:

  capture.PNG

  

  Concerning

  Véronique

• How to determine the cause of the ipsec tunnel fall on ASA 5510

  Is there an easy way to determine the cause of tunnel VPN ipsec l2l fall on one asa 5510? I have enabled logging, but the buffer is full so fast, I can't find something when it is 24 hours later. I'm working on obtaining a server/aggregator syslog configuration but... until it is complete I need a temporary measure. Suggestions?

  Hi Jessica.

  For the buffering limit, you can try:

  Increase the maximum buffer size.

  limit the newspapers to the class of vpn:

  Buffered Debug class vpn connection.

  On the other hand, you can try him debugs:

  Debug crypto peer peer_address condition

  debugging cry isa 128

  debugging ipsec 128 cry

  If you lose the ssh session debugging is disabled.  Finally for the vpn tunnels usually it goes down due to:

  Idle time-out

  the dead peer detection

  remove it from the other end.

  HTH.

• What is is it possible to use the acl extended for split tunneling on ASA?

  I'm setting up VPN IPSEC RA on SAA and I would like to know if it is possible to use the ACL extended as part of the split tunneling?

  Thank you!

  Yes, you can use the extended ACL. See this example:http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-nex...

  Kind regards

  Averroès.

• Can I use private as Source IPs from a remote network IP addresses while building the IPSec tunnel?

  Can I use private as Source IPs from a remote network IP addresses while building the IPSec tunnel? If not why? If so, how?

  Your explanation is much appreciated.

  Hi Deepak,

  In such a situation, you usually NAT traffic that goes to the internet, but exempt traffic that goes through the VPN, because it will be wrapped in packages with public IP (tunnel) addresses. You can use the same IP address on your interface in the face of internet for the NAT/PAT and source of IPSEC Tunnel.

• Restrict access to the remote computer of single machine or the single IP address.

  Hello

  I have a server on which I want to prevent users from remote session. All I want is to give access to a user or machine or IP and that this machine/user/IP can access the server remotely.
  I tried the below mentioned step and it does not work for me, maybe I'm missing something.
  Control Panel > administrative tools > Windows Firewall with advanced security > inbound rules > Remote Desktop (TCP-In) and I tried every tab scope, users, computers, I am still able to access the server of any filling machine.
  Please suggest is possible I can prevent the other users, I can't create a new user account, I have to share the password what I can do is limited to the single machine/user/Ip address.
  Please suggest.
  Concerning
  Yoann kassoum COULIBALY

  Hi, VC.

  I advise you to post this question in the Windows 7 IT PRO Forum /Networking. This community will be able to find solutions to your problems.

  B Eddie

• Backup of the GRE Tunnel using the address IP of Seconadary

  Is it possible to configure a GRE Tunnel to backup using an IP of Seconadary address on the WAN interface.  The router is a

  Cisco 871.  Any help would be greatly appreciated.

  Thank you.

  Nicholas

  I'm not sure it would work for use a secondary address on the WAN interface for a GRE tunnel. Maybe if you tell us more about what you're trying to do we could be able to help find alternatives that would work.

  Two tunnels from the same interface (even though you could use a secondary address) to another router would not provide a backup, if they work at all. Work of two tunnels of the same interface of router (and two using the main address) fairly well if they go to different remote routers, and it is a common way to provide backup for the GRE tunnels.

  HTH

  Rick

• do not display email addresses, only the single

  I want to send an email to 20 people where everyone will see that this mail is sent only to himself.

  If I put the 20 addresses in the BCC field and my own address in the to box, each recipient will understand that it is the only one?

  Thank you

  Didier

  Ken

  Thanks for pointing out, I suppose my response could have been better worded.

  What I should have said is that the recipient will not know the names (or numbers) from others in the ITC will at first sight list, guess that the enamel is alone. However, examination of enamel will reveal the address.

• Impossible to pass traffic through the VPN tunnel

  I have an ASA 5505 9.1 running.   I have the VPN tunnel connection, but I am not able to pass traffic. through the tunnel. Ping through the internet works fine.

  Here is my config

  LN-BLF-ASA5505 > en
  Password: *.
  ASA5505-BLF-LN # sho run
  : Saved
  :
  : Serial number: JMX1216Z0SM
  : Material: ASA5505, 256 MB RAM, 500 MHz Geode Processor
  :
  ASA 5,0000 Version 21
  !
  LN-BLF-ASA5505 hostname
  domain lopeznegrete.com
  activate the password
  volatile xlate deny tcp any4 any4
  volatile xlate deny tcp any4 any6
  volatile xlate deny tcp any6 any4
  volatile xlate deny tcp any6 any6
  volatile xlate deny udp any4 any4 eq field
  volatile xlate deny udp any4 any6 eq field
  volatile xlate deny udp any6 any4 eq field
  volatile xlate deny udp any6 any6 eq field
  passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.116.254 255.255.255.0
  OSPF cost 10
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 50.201.218.69 255.255.255.224
  OSPF cost 10
  !
  boot system Disk0: / asa915-21 - k8.bin
  passive FTP mode
  DNS server-group DefaultDNS
  domain lopeznegrete.com
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  the LNC_Local_TX_Nets object-group network
  Description of internal networks Negrete Lopez (Texas)
  object-network 192.168.1.0 255.255.255.0
  object-network 192.168.2.0 255.255.255.0
  object-network 192.168.3.0 255.255.255.0
  object-network 192.168.4.0 255.255.255.0
  object-network 192.168.5.0 255.255.255.0
  object-network 192.168.51.0 255.255.255.0
  object-network 192.168.55.0 255.255.255.0
  object-network 192.168.52.0 255.255.255.0
  object-network 192.168.20.0 255.255.255.0
  object-network 192.168.56.0 255.255.255.0
  object-network 192.168.59.0 255.255.255.0
  object-network 10.111.14.0 255.255.255.0
  object-network 10.111.19.0 255.255.255.0
  the LNC_Blueleaf_Nets object-group network
  object-network 192.168.116.0 255.255.255.0
  access outside the permitted scope icmp any4 any4 list
  extended outdoor access allowed icmp a whole list
  outside_1_cryptomap list extended access permitted ip object-group LNC_Blueleaf_Nets-group of objects LNC_Local_TX_Nets
  inside_nat0_outbound list extended access permitted ip object-group LNC_Blueleaf_Nets-group of objects LNC_Local_TX_Nets
  LNC_BLF_HOU_VPN list extended access permitted ip object-group LNC_Blueleaf_Nets-group of objects LNC_Local_TX_Nets
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 741.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  !
  network obj_any object
  NAT dynamic interface (indoor, outdoor)
  outside access-group in external interface
  !
  router ospf 1
  255.255.255.255 network 192.168.116.254 area 0
  Journal-adj-changes
  default-information originate always
  !
  Route outside 0.0.0.0 0.0.0.0 50.201.218.94 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  the ssh LOCAL console AAA authentication
  AAA authentication enable LOCAL console
  Enable http server
  http 192.168.2.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec pmtu aging infinite - the security association
  card crypto outside_map 1 match address outside_1_cryptomap
  peer set card crypto outside_map 1 50.201.218.93
  card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
  outside_map interface card crypto outside
  Crypto ca trustpoint _SmartCallHome_ServerCA
  no use of validation
  Configure CRL
  trustpool crypto ca policy
  Crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
  30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
  496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
  74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
  68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
  302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
  63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
  010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
  02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
  6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
  c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
  69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
  1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
  445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
  6c2527b9 deb78458 c61f381e a4c4cb66
  quit smoking
  crypto isakmp identity address
  Crypto isakmp nat-traversal 1500
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  aes-256 encryption
  sha hash
  Group 5
  life 86400
  IKEv1 crypto policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH 0.0.0.0 0.0.0.0 inside
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  SSH version 2
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  management-access inside

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  attributes of Group Policy DfltGrpPolicy
  Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
  username
  username
  tunnel-group 50.201.218.93 type ipsec-l2l
  IPSec-attributes tunnel-group 50.201.218.93
  IKEv1 pre-shared-key *.
  NOCHECK Peer-id-validate
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  call-home service
  anonymous reporting remote call
  call-home
  contact-email-addr [email protected] / * /
  Profile of CiscoTAC-1
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:e519f212867755f697101394f40d9ed7
  : end
  LN-BLF-ASA5505 #.

  Assuming that you have an active IPSEC security association (i.e. "show crypto ipsec his" shows the tunnel is up), please perform a packet trace to see why it's a failure:

   packet-tracer input inside tcp 192.168.116.1 1025 192.168.1.1 80 detail

  (simulating a hypothetical customer of blue LNC tries to navigate to a hypothetical LNC TX Local site server)

• Capacity of the crypto ipsec Cisco ASA 9.1 stats system failures

  Hello

  I'm trying to find some performance issues on one ASA centralized and some site VPN settings.  I already address bits of fragmentation and flow control which seeks to solve performance problems, but I came across something that I can't identify to understand what he said.

  I can't seem to find any documentation that explains what triggers the counter for "Capacity of the system failures" on the stats command see the crypto ipsec:

  crypto ipsec sho stats #.

  IPsec statistics
  -----------------------
  The active tunnels: 41
  Previous tunnels: 8999
  Incoming traffic
  Bytes: 8292491846127
  Decompressed bytes: 8292491846127
  Packages: 25115896849
  Packet ignored: 1291637
  Review of chess: 220
  Authentications: 25114592561
  Authentication failures: 0
  Decryptions: 25114592564
  Decryption failures: 0
  TFC packages: 12836
  Fragments of decapsules who need reassembly: 17418535
  Invalid ICMP received errors: 0
  Invalid ICMP received errors: 0
  Outgoing
  Bytes: 37818073925334
  Uncompressed bytes: 37818837785556
  Packages: 38014583887
  Packet ignored: 2413164
  Authentications: 38020189281
  Authentication failures: 0
  Encryption: 38020191839
  Encryption failures: 0
  TFC packets: 0
  Success of fragmentation: 7763651
  Fragmentation before successses: 7763651
  After fragmentation success stories: 0
  Fragmentation failures: 267158
  The failures of previous fragmentation: 267158
  Fragmentation failures after: 0
  Fragments created: 15527302
  PMTUs sent: 267158
  PMTUs rcvd: 185
  Protocol of failures: 0
  Missing chess SA: 255102
  Outages of capacity: 3167258

  Does anyone have knowledge of what this is referring to specifically?

  Cheers, Dale

  Hello

  What is the model of the ASA you have and how many vpn sessions you get on average during peak hours?

  Lack of capacity occurs when it is short of ability of the material or the use...

  Concerning

  Knockaert

• How to change AnyConnect VPN remote to complete the split tunnel tunnel?

  I couldn't find an answer through the config of the SAA in the Cisco documentation and using Google.  To activate the complete tunnel for the AnyConnect client group policy, I just need to change the policy of Tunneling split to all networks of tunnels and set list of network voice against zero, if I want someone who connects with the AnyConnect customer to guarantee mobility to use internet corp pipe?

  Who, more you will also need a NAT nat rule VPN pool meets the ASA outside interface (or if address / hen you normally use for dynamic NAT).

  There are a few good examples with illustrations in this document.

• Authentication of ACS in the VPN tunnel

  We want to enable the ACS authentication to connect to different routers (Cisco 881 s) we have obtained who are communicating with our WAN via VPN tunnels. We want to avoid using public IP of the router to communicate and pass information to user/password with the ACS server and rely on the IP of the server private instead. The problem is that external interfaces of the router connect to the Internet using public IP addresses and when the router wishes to communicate with the ACS server it will use its IP of the interface to the public and which will fail. We can ping on the server of course when we set the source to the internal LAN IP.

  The question is are there any way to have the router contact ACS through the VPN tunnel using a private IP address?

  config is used and tested with success on local equipment:

  AAA new-model

  RADIUS-server host 10.x.x.x single-connection key xxxxxx

  AAA authentication login Ganymede-local group local Ganymede

  AAA authorization commands x Ganymede-local group Ganymede + if authenticated

  AAA authorization exec Ganymede-local group Ganymede + authenticated if

  See the establishment of privileges exec level x

  line vty 0 4

  Ganymede-local authentication login

  authorization controls Ganymede-local x

  -ACS ping to the router (WAN via VPN connection) when using public IP address of the router as the source address:

  RT881 #ping 10.x.x.x

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 10.x.x.x, time-out is 2 seconds:

  .....

  Success rate is 0% (0/5)

  -ACS ping to the router (WAN via VPN connection) when using IP private of the LAN as source address:

  RT881 #ping source 10.x.x.1 10.x.x.x

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 10.x.x.x, time-out is 2 seconds:

  Packet sent with a source address of 10.x.x.1

  !!!!!

  Success rate is 100 per cent (5/5), round-trip min/avg/max = 72/72/76 ms

  Looking forward to your responses and suggestions.

  Thanks, M.

  Hey Maher,

  You can use the command 'Ganymede-source interface ip' or 'RADIUS source-interface ip' for your scenario.

  I hope this helps!

  Kind regards

  Assia

• automatic start of Tunnel VPN ASA.

  I was wondering if anyone had ideas for a problem I'm having.

  I had previously configured a router IOS which had a dynamic IP address from the ISP vpn to PIX headquarters. I got the PIX configured to address generic isakmp/crypto peer so he did not care what peer IP address attempted vpn handshake with him. But, in order to show the VPN, to be launched on the side IOS router because of the dynamics to static vpn LAN is configured.

  The problem I had initially was behind the IOS router on its side LAN I had cameras that has not generated any traffic by themselves, so the VPN is not never come to the top and how I had the time that was on the IOS router I set an IP address of the fake NTP server that was in the subnet through the VPN on the side of PIX and then source the The IOS NTP ethernet router so it would automatically take place of the tunnel by himself.

  Now we are trying to implement and ASA instead of and router IOS and the NTP commands are there including the source option that can be 'inside' or 'outside' but it does not work as did the IOS router. I also tried to create a kind of SNMP or SLA with some source options but who did not bring to the top of the tunnel either. It's as if he's not he sourcing from an IP address or interface that looks like to the interesting traffic.

  I wonder if it's something to with the fact that the ASA, we set up we did put the IP addresses on the local VIRTUAL network interfaces and then put the Ethernet Interfaces in the vlan access switchport special instead of putting on the Interfaces Ethernet IP addresses themselves.

  Someone has any ideas in order to automatically initialize the vpn tunnel to the ASA configuration?

  You may need to add outside of ASA interface as interesting traffic. That is usually when you want a remote ASA/pix syslog to a local syslog server. I know you do ntp, but should be the same. Looks like the same problem here. In any case it is worth it.

  Here is the doc for pix but it is similar to the ASA.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a0080094469.shtml