Configure the OIA to connect again OIA DB.

Similar Questions

• Cannot configure the BPM MDS connection in JDeveloper

  I am trying to set up a connection to MDS of BPM in Jdeveloper
  
  Here's how I do it:
  1. in BPM MDS Navigator set up the connection.
  2. click on add a connection to the wizard
  3. as I have no SOA MDS connection can't created, click Add to add the SOA MDS connection.
  4. in the MDS SOA, SOA MDS connection correctly connection wizard created.
  5. now, this created SOA MDS connection does not appear in the menu dropdown and I am not able to proceed further with the creation of BPM MDS connection.
  
  Tried to restart Jdeveloper and refreshing so this does not help, as the SOA MDS connection created is visible in the IDE connections palette but not is not in the drop-down for the configuration of connection MDS BPM.
  If you'd be grateful if someone can help on this.
  
  
  Thank you
  Wajid
  
  *****************************
  Resolution:
  
  Ensure that the Weblogic domain created had the possibility of BPM Suite verified.
  
  ****************************
  
  Published by: Carole Wajid on 22 September 2012 18:49

  So here is the solution

  The problem was with my weblogic domain , I did not create domain included Suite BPM[while the creation of the field made sure the BPM Suite is checked].

  Resoultion->
  Created a new domain with BPM Suite and it worked like a breeze.

  See you soon,.
  Wajid

• Cannot configure the Wi - Fi connection with myRIO. Error message: can not connect. Incorrect credentials.

  Wireless network authentication information in what I typed is correct. I also tried to connect to wifi not school, but that no longer works. Any ideas for a fix?

  Difficulty:

  Create a network using the myRIO and connect on your computer rather than trying to connect to your LAN with the myRIO.

• WRT54G2 - can not configure the wi - fi connection

  Hey all,.

  just received this new router today.  I configure everything for my home network, port forwarding, static ip, etc...

  now I try the security configuration wi - fi.

  I do manual mode, and I'm on the Wireless Security tab.  No matter which option to choose in the drop-down list, the browser immediately refreshes and returns to the security mode off.

  I tried both manual and protected... no matter what I do, when I choose a security mode, it's just always refreshs and back for the disabled

  Anyone have any ideas?

  also, where is the firmware for this?  I can't find the product in the downloads section.  Cannot find the router in the list

  First try to use another computer to configure the router.

  And you can also try to update the firmware on the router of www.linksys.com/downloads.

• Is it possible to automatically configure the Wi - Fi connection?

  Hello world

  I would like to know if it is possible to make a Wi - Fi connection to a gateway specified from a java application.

  Our application must ensure a wireless ap device to work properly.

  It is a bit difficult and tedious for a user, click on Set Up Wi - Fi Connection and then do Scan for networks of each course they'are of time to use our program.

  So, I'm going to make a connection to the access point when the program starts. Users will be enter the access point name only once if they use this program for the first time.

  Is it possible to do like that? Someone said that it is possible to do so in a post of Java development. But he doesn't say how.

  My phone is BB 9000 "BOLD" and I use BB JDE 4.6.0.

  It is very important. any comments would be very useful for me.

  Thanks in advance for your help.

  Kim,

  I don't know how to do this. usually, the bb will connect automatically saved networks if you select.

• Cannot configure the initial network connection

  I can't cross him select your Wi - Fi network on my new Mac Book. I have my MacBook Pro sitting next to. I know that the network (my house) and the password. My MBP is connected correctly. On the Mac Book, I'm selecting the network with a return and type the password then hit a return. The book of Mac is just the saying of circle of rotation in search network. I tired even go to another and by typing the name and the password. He put me on the screen next to the transfer of information. I said no and then I tried to move forward, but when I type my apple ID and password, it says: error server in red and try again. I know that those who are correct, also because I am enrolled in icloud on my MBP to confirm that I wasn't not commit an error.

  I have reset the router, rebooted the computer, nothing works. I spent two hours and my husband loving PC is just laugh. Any suggestions on what I can try next?

  I also tried to use a personal hotspot from my iPhone. Still not connect. I don't know why it says resolved, because I am not and can not figure out how uncheck that. Teenager also tried and got the same results as me.

• How to configure the port to connect the SG300 switch to 3com switch

  Hello

  I need help. I have my network with multiple switches SG300.

  I have one of them as my base switch working mode layer 3. With 2 VLANS and vlan interfaces to each vlan.

  Everything works ok.

  But now I need to plug a 3com unmanage switch who welcomed of vlan 1 and 2. How can I connect this switch to my Cisco sg300 switch? Which mode to use in this port?

  Thank you very much.

  SG300 Switch L3

  I have

  I have

  SG300 L2 switch

  I have

  I have<-------- how="" should="" i="" configure="" this="" connection="" to="" support="" all="">

  I have

  3Com unmanage switch

  I          I

  I          I

  I have vlan 1

  VLAN2

  Use of VLAN based on MAC on SG300 L2 switch, record all customers on the required VLANs (or better configure port SG300 L2 to 3com in VLAN PVID with maximum and other clients in the VLAN based on MAC).

• Wireless network disconnects and then take the time to connect again

  Hello

  We have a wireless network, composed of 23 WAP (1700) and WLC 2504. We have three SSID, 2 in vlan 120 and the third in the vlan 121.

  The network takes time to connect to any SSID, and after three or four attempts, it connects and some time connected to less range and a few times at all, even if we are under the WAP.

  Can someone please help me on this, as I am new on wireless and my main area of activity is R & S, SP and DC.

  Any help or the index will be very appreciated.

  Thank you.

  Kind regards

  Adnan

  I see no error with config.

  What version you use WLC?

  Are there any specific client having problems connection or all devices?

  Concerning

  Remember messages useful rates

• How to configure the remote desktop connection

  Original title: home remote desktop connection

  trying to desktop connection remote set-up on a spare home computer how I would go all this? my main computer is wired ethernet my spare part is wireless

  Hey Shawn,.

  Follow the steps in the link to set up a desktop connection remotely on computers.

  http://Windows.Microsoft.com/en-in/Windows7/allow-remote-desktop-connections-from-outside-your-home-network

  In addition, through the FAQ for remote desktop connection of

  http://Windows.Microsoft.com/en-in/Windows7/Remote-Desktop-connection-frequently-asked-questions

  For any questions, have a look on

  http://Windows.Microsoft.com/en-in/Windows7/why-can-t-i-connect-using-Remote-Desktop-connection

• How to configure the computer to connect to a specific pool in sight

  I'm trying to find out how to get some machines to automatically connect to a specific pool, I created. What would be the best way to do this?

  Thanks for any help!

  There are settings of command line for the client to display which allows you to specify the pool and desktop computers, you should connect to.

  Use of VMware View Client command-line build-233023 4.0.1:

  desktopName - Office of XXX for autostart

  domain name - domain XXX for server connection

  -folder XXX file with the additional command line parameters

  (If available) XXX - languageId to use language ID

  -non-interactive message boxes of repress to start fully scripted error

  -password XXX for server connection

  desktopProtocol - XXX try using the specified protocol desktop display

  desktopLayout - Office XXX screen size specify (for example, fullscreen, multimonit

  or, windowLarge or windowSmall)

  -XXX URL serverURL to the view connection server

  logInAsCurrentUser - XXX connect you as an existing user

  user name - XXX user name for the server connection

  -rollback cancels a check out (required - desktopName)

  -Check box on the desktop for use in offline mode (required - desktopName)

  )

  -checkin Check in the office (need - desktopName, must be verified

  out)

  staycheckedout - stay checked after check-in (required - desktopName)

  offlineDirectory - path Local to check Office (required - desktopName)

  -?                      Display this help

  Option names are case sensitive.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• How to allow the links to connect again

  I need help! I created a Word document with hyperlinks. Then converted to PDF. When I clicked on the links he asked me to block or allow the source, by mistake, I clicked on the block and the box "Don't ask me" was checked. Now I can not understand how change that option and I already tried to delete the document and convert it to PDF format once again and it won't work, there is no more trust the source.

  Can anyone help?

  Thank you!

  You don't say what version of Acrobat, but AA8, you'll change > Preferences > General > General and there is a button to reset all warnings.

• "Limited connection" when you configure the network between two computers XP.

  Original title: Configuration of the network connection

  Trying to establish a network connection between two home PCs., both running Windows XP Pro. Have been through the network on both PC Setup Wizard but, they still say limited, in fact no connection. I use an Ethernet cable between the two Crusader. If it is true what I'm doing wrong?

  Thanx Terry

  Old but good, networking tips from MVP Malke, MS:

  The best and simplest is to buy a wireless router. This way you get Internet connectivity both machines and the added benefit of security more between you and the Internet. Then you configure your network wireless safely, and then you configure file/printer sharing. Here is information on the implementation of a router and also in networking. It seems long, but don't be intimidated. Setting up a router and the LAN of sharing between two computers takes about 15 minutes.

  The router configuration

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.

  2. attach a cable (usually supplied with the router) course Ethernet cat5e Internet/WAN port of the router to the Ethernet port on the cable modem.

  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.

  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

   

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar.

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). If you have a newish computer, you will be able to affect security WPA2-Personal Mode. Do this and enter a password. The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the Ethernet cable and wireless of the computer should see your new network. Enter the password you created to join the network and start surfing.

  *****

  B. file/printer sharing of

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus with "Internet Worm Protection" (like Norton 2006/07) which acts as a firewall, you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this. The instructions on this link work for XP and Vista:

  Set up Windows to automatically connect (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.

• Configure the ACS 5.1 device to connect to the AD

  Pls advise.

  This is a new installation. I had to configure the ACS to connect to the ad to authenticate users and retrieve user information for the group as a result of step mapping.

  Go to the users and identity stores > external identity stores > Active Directory and enter the domain name

  appoint and give a name of user and password which will allow to connect to the domain. Then, click Test connection to validate join them the domain.

  I got successful connection test. But when I click on save changes. I got error.

  How has the problem been resolved?

  

  Best regards

  Boonkiat

  It can be many things.

  DCs how do you have in your area? They are all accessible by the ACS?

  You return the SRV records for your ad?

• How to configure the network home wiFi with dlink router

  I need to create a home network using the dlink WiFi router
  a computer with Vista and the second with XP
  can someone tell me what havo to do to configure the router etc etc o give me same informamation on where I can learn to do
  I want just the old pc with xp for the server and the vista one customer but more importantly I need the file on XP to migrate under vista.
  Thank you very muche for your end of the patient cooperation
  in return, I give free cooking classes
  see you soon

  I'm not sure if you are asking how to set up a secure wireless network, if you ask how to share files between your two computers (and there is no "customer" or "server" in a working group, in a field - which is not), or both.

  So I will give you information on doing both.

  Router - configure manually

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.
  2. attach a class (usually supplied with the router) ethernet cable cat5e port Internet/WAN from the router to the ethernet port on the cable modem.
  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.
  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine. The first thing to do is to change the default password because * all * known default passwords for different routers.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar. ;-)

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). Most computers purchased during the last 4 years have the wireless hardware that will support WPA2-Personal (also known as WPA2-PSK). This is the desired encryption level. If your wireless hardware is older, use WPA. Don't use WEP, because who is easily broken within minutes. So go ahead and set the Security Mode WPA2-Personal. Do this and enter a password. For example, you could use the password ' here be dragons, beware you scurvy dogs! The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the ethernet cable and wireless of the computer should see your new network. Enter the password that you have created (exactly as you wrote it with all capital letters and punctuation) to join the network and start surfing.

  Networking

  Here are the steps of general network troubleshooting. Just cannot apply to your situation, so just take the bits that are. It may seem daunting, but if you follow the steps in the links and suggestions below calmly and consistently, you will have no difficulty to implement your sharing.

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  XP - configure Windows to login automatically (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  Vista - Start ORB > Search > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.
  MS - MVP - Elephant Boy computers - don't panic!

• BlackBerry Smartphones using the BBM after connecting through wifi?

  I just arrived in canada and I have connected my torch to wifi wpa personal, the browser works well but my bbm is not working, can someone please tell what to do to plug on bbm?

  Thank you

  Fankoosh wrote:

  No I don't have an international plan, but I had my sim card on until it got to with the fact that bbm does not work on wifi

  Yep, that will definitely throw a crimp in your BIS data connection.

  How can you not have noted that early?

  • Put the SIM card in and start the backup.
  • Leave the appliance to connect again with your network, roaming.
  • Then you should be able to go to your Mobile network settings and to disable the connection to your mobile phone network and to use BBM and email, etc., through WiFi only.