Connect HP Pavilion p6610f old receiver onkyo (TX 866)

Similar Questions

• Satellite P300 connected via HDMI receiver Onkyo 607 - no sound

  Hello

  I have the Satellite P300 1BB for awhile and I'm very happy with it. But now I have a problem with the P300 HDMI port. I connected with my Onkyo TX - SR 607 5.1 receiver HDMI. The image is there, but there is no sound. If I connect the P300 directly to my plasma tv, then there's sound through HDMI.

  I have updated the Conexant audio driver to version 4.83.1.0. The Panel mixer, audio, the audio driver for AMD HDMI Conexant is not connected when I use the 607. It is connected (and works perfectly) if I use the plasma tv.

  Is it possible to get this working?

  Hello abdoulraak

  Please don't be crazy about me, but how you write that you have problems with port HDMI on Satellite P300 when working with TV. I think you have problem with your receiver Onkyo 607.
  All of these updates will be not useful at all and you should check s manual Onkyo to see how it works and what kind of parameters that you can use the receiver itself.

  You have activated a right channel of the receiver? I have big receiver Technics and all the ports on the back will be used with a separate channel that needs to be enabled.

  See receiver manuals and collect information how it works exactly.

• Office Pavilion p6610f HP says: use SATA0 or 1, but HD is in Port 11 should I go back and change?

  HP Desktop Pavilion p6610f 64bits just installed new refurbished Hard Drive No. OS and yet I followed all the steps in the tutorial of HP, but one thing I didn't notice at first was that HP is said to use the smaller ports numbered disc hard SATA Seagate SATA HD shows that it is in the drive of 1st in the BIOS and when I checked for the SATA port There was just the USB ports, I assumed they were the same, but the only ports connected on 11 were the mouse and the keyboard on the 6 & 7 and a mass on the 11 port storage device (that is the hard drive?)  If it's the hard drive, do I go back and unplug something and put it in the USB port 0 and port 1? I had so many problems with the computer from another installed a faulty? hard drive, after the failure of the original, and I just wanted to be sure I did well, and it would be so good sail once I install my Diska recovery and follow other steps suggested by hP.  I guess I'll let it start and see what happens. (I'm on a right of the laptop next to my office right now)  It said to restart with the appropriate boot device.  I guess I should put in the first disc of recovery means turn the computer off then turn it back on again.

  My hard drive installation was a success and now, after installation program recovery discs and 100's of updates Windows and updates of the HP driver, everything seems to work very well.  The hard drive is intalled in port 1 and there is no noise as if it was with the previous replacement hard drive.  But things are still running much slower than they were before the crash.   I disabled elements start and removed many unnecessary programs and don't have not download all of my old library backup files in order to preserve the memory. I will buy and install several memory cards, a mink, update the BIOS Hardware Diagnostic test and hope that somewhere along the line, I will not solve the problem.  I consider this case closed and I thank all those who have posted to give me a helping hand.  Taylor

• Pavilion p6610f Desktop Hard Drive will not be reset to zero when you restart

  HP Pavilion p6610f than Desktop PC Windows 7 Home Premium 64 bit HDD (I think) could not restart. There was no indication of a problem before me by clicking on the button restart. I have this sometimes just to clarify things, looks like things work better. When it restarted, it went to a screen with 2 choices 'launch start repair or load normally. I chose startup repair. He loaded some files & drivers but finally comes to the screen 'blue '. I tried to start the computer with all the 'F' keys, none worked, always came back to the blue screen. Tried to start the recovery discs I did, same thing. I started with the ERD that I did it. Same thing. Would not not even go to Safe Mode. Nothing. But, there is no prior problems. Nothing made me think that I should do something to deal with a disaster. Then a "friend of a friend" came and replaced the hard 'for free' drive and installed windows 8 (which I hate) and now the computer makes a ticking noise and a sound plaintive, as when there is a bad DVD in the drive, it work so now slow, freezes, takes internet forever and made so much noise I think it's going to explode. I think I should replace the hard drive with the "right" and then use my recovery disks. He said that windows 8 was just too big of an OS for the hard drive, it took, that is why it is slow. But couldn't I erase or reformat the hard disk, and then use my recovery disks. As it is, I have no HP software on the computer more.  Is there a way to get the data from my old hard drive? I'm willing to take the time to learn how to do all this by myself if I knew that this is possible and if it is useful? [edited font color and characters]

  Hello Ty965,

  I understand that you fell on some hard drive problems and a friend of a friend installed a former player for you and since he turned slowly and noisily. Personally, I recommend that you buy a new hard drive and then review and follow the instructions on the HP Support document: performing a recovery of HP (Windows 7) system, which will guide you through the recovery process and get your computer back operational.

  If you don't have the recovery discs for your computer you can buy them for a cheap price of HP Media software and the drivercommand.

  I hope that I have addressed the issue to your satisfaction. Thanks for posting on the HP Forums. Have a great day!

• Pavilion P6610f Desktop Tower a ticking noise, can turn back be opened while still running?

  HP Pavilion p6610f desktop win 8 64 bit since my hard drive has failed and a friend of a friend installed another hard drive and insisted on the fact that I install Win 8 instead of 7, (I hate Win 8), there is a click inside the tower and I also hear something that seems to hold the bike to the top then then down every few seconds, the ticking is almost every second. I checked the power that I knew how. Configuration and System Device Manager and it says disk hard does not work properly and is no need for an updated driver. But everything is so slow and things don't work a lot of the time, the internet will not load or merely far sometimes but convenience store network says it is connected and functional. I sometimes can't features to not work the control panel.  I tried the diagnosis of memory in the administration settings, but it wouldn't work. Before I could get my Win 7 backup files on Win 8, PC showed that I had 220 GB of 232 GB memory left possible on the replacement hard drive. I have 4 GB of Ram on a 16 possible and I thought shoud get more. I was just wondering can I have the back off the coast of the Tower during its execution so that I can see that actually the sounds before investing in another hard drive and memory cards? I'm so unhappy with my computer that I love even more to use it and I used to stay on 10 to 16 hours a day.  I don't have microsoft nhave word more and I miss the fonts that he used and for a reason that these fonts are missing off the coast of my e-mail program when they were there before the failure and the loss of MS Word IE fonts. Sorry so long winded. Taylor

  Taylor,

  No long-term, just percise. Liked it.

  (1) you can observe with the box to open, but get a grounding strap. (for example).

  (2) If you want to WIN 7 64 bit, see here

  (3) memory is available here (2 PCs 4 GB)

  (4) MS Office Starter 2010 is still free.

• Dual monitor on HP Pavilion p6610f

  I would use two monitors on my HP Pavilion p6610f desktop computer.  I have two lcd monitors.   I buy a vga adapter digital and connected a monitor to the VGA in the back of the computer and plugged the adapter connected to the other lcd screen in the digital output on the back of the computer. The monitor connected to the digital output signals no signal.

  Can I use a Setup dual monitor on a pavilion p6610f using video output that is on the motherboard, or do I need an additional video card?

  Thank you

  cardsinstl

  Hello

  The monitor which does not have a DVI port?  What make and model of the monitor does not work?

  Sending a digital signal to an analog monitor won't work.

• Pavilion p6610f Desktop: software blocking Wifi transmission

  Pavilion p6610f Desktop 64 bit Win 7 Home Premium SP1.  I had problems with the buffering and freezing in my browsing on the internet. I contacted my Internet provider after doing all the clean to the top of my computer that I knew how to do. After an hour or two with the agent to remote access to my computer and them telling me that everything was going well at their end, I asked why the icon Wifi in my taskbar shows only two bars on a possible 5 when my computer is right next to my Wifi modem? I was told it was probably a software interfering with the Wifi transmission.  I ran Microsoft malware and adware programs removal & Ms. Mr. Fixit.  I have MS Security Essentials and have not all problem reports.  My provider Internet telling me the truth?  Is the lack of Wifi reception with software that I can't find? I looked in my programs & features and does not see all unauthorized programs may have snuck in and I deleted some. The only thing that is new is a HP Envy 5660 all-in-one that is set up wireless.  It has been suggested that I have reformat my hard drive and reinstall the essential programs to see if that helps. But, acckkKKK!  I don't want to go through all that again! I did twice before and have installed two others had readers since I've owned this computer and don't want to if not necessary!  I thank in advance for your time and your knowledge if you decide to advise me.

  Hi there @TY965

  Welcome to the Forums of HP Support! It's a good place to find the help you need, other users, the HP experts and other members of the support staff. I understand that you are getting a signal strength wireless low, despite the close proximity. I'm happy to help you with this.

  In some respects, being too close could be part of the problem. Because of the arrangement of the devices, it could be that the receiver on your desktop does not receive a clear signal, due to the metal in its framework. I suggest moving the router wireless in the location and see if you can get a better signal. This page has also some other useful information which may affect the strength of the signal.

  How to get a better Wireless Signal and reduce interference of wireless network - howtogeek.com

  If that does not help or make a difference, then you can try looking at your system itself. Start with the next page, and if there is no improvement, wok your way through the other sections, I have included, until it is resolved.

  Troubleshooting your wireless network and Internet access (Windows 7)

  Focus on the management of feeding your wireless adapter:
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.

  Forget the network: (Windows 7)
  1. press start.
  2. tap manage wireless networks, click on the application at the top of the start menu.
  3. right click on the network, and then click on remove network.
  4 confirm the warning by clicking OK.

  Reset TCP/IP on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.

  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.

  Reinstall the NIC drivers:
  1. download the drivers from here, but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.

  I hope that this help and if anything here solved your problem, please mark this message as a solution.

• I cannot connect hp pavilion labtop 2000 fx for I - Phone 3 16 GB via blue tooth

  I cannot connect hp pavilion labtop 2000 fx for I - Phone 3 16 GB via blue tooth

  and not even with connection cable USB

  Hi removed Abu Qorah,

  1. are you able to connect the iPhone to other phones or another computer via Bluetooth and usb with no problems?

  2. you receive messages or error codes?

  You can see the Apple support article and see if it helps:

  iOS: device not recognized in iTunes for Windows

  Hope this information is useful.

• Two monitors of Pavilion P6610f

  A previous post on this topic left unanswered question of the user.    I have a Pavilion p6610f product #BM417AA #ABA.  Given that this machine has both a output VGA AND DVI output, it is possible to have TWO monitors (working simultaneously) provided that a monitor is analog (VGA) and the other monitor is digital (DVI)?  I didn't "want to go to the load of the material, if only one of the two monitors can be used at a time.  Thank you.

  The chipset on the motherboard is able to handle two monitors. And I found this on the motherboard page: http://support.hp.com/us-en/document/c02560084

  Integrated graphics: concomitant use of DVI and VGA ports is supported.

  So, Yes, it seems to support the two ports.
  

• Want to buy the new ipod nano, how can I connect this to my old itunes library without losing all my songs

  Want to buy the new ipod nano, how can I connect this to my old itunes library without losing all my songs

  Back up your library, update if necessary iTunes and sync the iPod. This will not normally remove anything from the iTunes library, but other things can.

  (138265)

• driver for the ethernet connection on Pavilion M7750n

  Can someone direct me to where I can download the driver for the ethernet connection on Pavilion M7750n?

  The list of specifications HP:

  Hello:

  No, use the chipset XP driver...

  http://www.nvidia.com/object/nforce_winxp_15.26.html

• 66610f Pavilion: Pavilion p6610f motherboard

  I'm looking to improve the performance of my Pavilion p6610f and already updated my card video and power. Can the processor or card mother being upgraded for games with a 1080 p display? If so, what would be a good choice?

  Current record of my office is:

  OS: Windows 7 Home Premium 64-bit

  Processor: AMD Athlon II X ~2.9GHz 4 635

  Memory: 4096 MB RAM

  Video card: AMB Radeon HD 6570

  I did some looking around and I couldn't find a processor that is an upgrade for you that uses this type of socket. It's an AMD Phenom II X 6 1075 - 3 GHz. I found it on Newegg. Here is a link.

• Publisher cannot connect XBOX 360 controller wireless receiver PC on Windows 7.

  I can't connect a XBOX 360 controller to my PC with the receiver wireless on Windows 7 (64-bit). I have correctly installed the driver, and the wireless receiver is recognized by the PC. The problem occurs when I try to connect the controller to the receiver, as do not connect or recognize each other. I press the Connect button on the receiver, then the light starts flashing. I then press and hold the connection button on my controller, which makes the quadrants "search for", but they quickly cease, and instead assign a specific quadrant, all quadrants begin to Flash instead, as before. Nothing seems to work, I have tried to unplug all other USB devices and wireless, connecting the receiver to different USB ports and change the batteries. What should I do now?

  Hello

  I suggest that you follow the steps in the article below:

  http://www.Microsoft.com/NZ/DigitalLife/gaming/how_to_connect_an_XBOX_360_controller_for_windows_to_a_computer.mspx

• I just bought the app for photographers creative cloud when I try finally connect with PS CC, I received an error message that says "no detected subscription. I don't really know how to solve this problem, I used my Adobe ID to connect several times

  I just bought the app for photographers creative cloud when I try finally connect with PS CC, I received an error message that says "no detected subscription. I don't really know how to solve this problem, I used my Adobe ID to connect several times and it just still the same message.

  Your subscription to cloud shows correctly on your account page?

  If you have more than one email, you will be sure that you use the right Adobe ID?

  https://www.adobe.com/account.html for subscriptions on your page from Adobe

  .

  If Yes

  Some general information for a subscription of cloud

  Cloud programs don't use serial... numbers you, connect you to your cloud account paying to download & install & activate... you may need to sign out of the cloud and restart your computer and log into the cloud for things to work

  Sign out of your account of cloud... Restart your computer... Connect to your paid account of cloud

  -Connect using http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html

  -http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html

  -http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

  -http://helpx.adobe.com/creative-suite/kb/trial--1-launch.html

  -ID help https://helpx.adobe.com/contact.html?step=ZNA_id-signing_stillNeedHelp

  -http://helpx.adobe.com/creative-cloud/kb/license-this-software.html

  .

  If no

  This is an open forum, Adobe support... you need Adobe personnel to help

  Adobe contact information - http://helpx.adobe.com/contact.html

  Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">

  -Select your product and what you need help with

  -Click on the blue box "still need help? Contact us. "

• Since Acrobat Reader downloaded DC I can't sign my PDF documents. It does not give me the option more and yes I am connected. On the old version, I got no problem with clicking on "signature" and draw the area where I needed my signature, put passw

  Since Acrobat Reader downloaded DC I can't sign my PDF documents. It does not give me the option more and yes I am connected. On the old version, I got no problem with clicking on "signature" and draw the area where I needed my signature, put the password and "POOF" my signature would be there. With this new version, it won't do that or give me the option. The online help is useless. I need to explain to me how connect you as I used too?

  Hi nicholass35183848,

  I assumed that you had a digital signature created in your player application of old and whenever you use to fill out a pdf with a signature field signed you it. But in order to draw and then sign you must use Acrobat Pro DC no DC drive.

  Thank you

  Abhishek