Connect mercury 3500 to NI 9401

Similar Questions

• Connections of encoder with cDAQ 9401

  I hope that some of the experts here can help me with this as I am new to encoders. I want to make sure I connect this right but am finding conflicting information on this subject. I found this tutorialwhich shed some light on some things for me.  If I interpret it correctly, 9401 card that I use (with 9172 chassis) can provide 5 VDC needed excitement for the encoder on any unused line. However, I have seen a response to an applications engineer OR which suggests an external power supply is necessary to this thread.

  So my first question is if I need an external power supply.

  Secondly, I have an encoder with 8 sons and am a bit uncertain to know if I need to connect each of them for my angular position measurement, I don't see any reference to A', B ', Z' in the documentation I found. Here is the datasheet for the encoder I use, in line driver configuration (I think it's x 2).

  I have also attached a picture of the stitching and the configuration of the meter for this encoder for someone who won't get the full data sheet.

  Thank you in advance to anyone who can help!

  Hi Johnny,.

  In this case, as we have said before, this module won't be able to excite your encoder properly using digital lines. It will not be able to provide the full 5V on a given channel output. Also, since the input for your encoder voltage is 4.75V minimum, you will need an external power supply. Who will provide the adequate power to drive this encoder. As long as you can excite the encoder properly, this module should be good to read the signals and interpret them for angular position measurement.

  Chris

• Capture of frequency with the NI 9401 in cDAQ-9172

  Hi all

  I searched through all the examples and find the same results than my own code in Labview. So, I go back to my hardware to solve my problem. I use a digital tachometer that displays pulse with 2 wires (hot and ground). I connected these to the NI 9401 for 16 PINS for PFI 1 and PIN 3 on the ground. When I open the module through MAX, he reads the perfectly when hi and lo as well as count properly if it is placed in the location 5 or 6.

  However, I try to use the frequency max task and the task fails to capture anything in the table. I get a time-out error, even if my tach is read correctly. I have attached my settings of the task. Thanks for any help

  Your samples to read is set to 100.  If all the samples of 100 are not available before the timeout is reached, you will get a time-out error.  What is the frequency of the input signal?  Maybe just try to read 1 sample on request first.

  Best regards

• X 3500 HNAP call to the device failed for an unknown reason.

  During the installation process Cisco Connect X 3500 briefly to connect to internet (can surf the net very briefly in this window) but when he arrives at the end of the installation it saying unsuccessful then restarts.  Is there a way to manually connect just using the address IP is a browser?

  Error code: 82BD0305

  Error description: year HNAP call to the device failed for an unknown reason.

  Model name: loading...

  Model number: X 3500

  Serial number: unknown

  Firmware version: loading...

  Operating system: Windows 7 SP 1

  Software version: 1.4.12340.0

  Connection type (WAN): loading...

  (LAN) IP address: loading...

  (WAN) IP address: loading...

  The computer IP address: 192.168.1.103

  Found!  At the bottom of the Cisco Connect program window is a link to configure manually via a web browser.

• HP mini 110-3500: no VGA connection more after installing Linux 16.04 LTS

  Hello!

  I can't fix my VGA problem in recent weeks and your community can solve it!

  I'm new to Linux and I have installed the 16.04 LTS version in my mini HP 110-3500.

  No more and all other system inside HP program.

  Before Linux 16.04 LTS, a BENQ F93GX external VGA display was connected to my HP mini computer, but leave now "not received no signal" message appeared on it when I turn it on «»

  I've installed some utilities and drivers from here and there, does a little work, but, I always in the dark.

  Below that pop up with the commands:

  1 - lspci k | grep-iA2 VGA

  00:02.0 VGA compatible controller: Intel Corporation Atom D4xx/D5xx/N4xx/N5xx Processor Integrated Graphics Controller
  Subsystem: Hewlett-Packard Company Atom graphics processor integrated D4xx/D5xx/N4xx/N5xx Controller
  Kernel modules: i915

  2 - xrandr without connected VGA:

  xrandr: failed to get the size of gamma for failure to exit
  Screen 0: minimum 1024 x 600, current 1024 x 600, 1024 x 600 maximum
  by default connected 1024 x 600 + 0 + 0 0 x 0mm
  75.00* 1024 x 600

  3 - xrandr with VGA connected and "lit".

  xrandr: failed to get the size of gamma for failure to exit
  Screen 0: minimum 1024 x 600, current 1024 x 600, 1024 x 600 maximum
  by default connected 1024 x 600 + 0 + 0 0 x 0mm
  75.00* 1024 x 600

  I received help from other communities, but the problem still there, can you please give it a try?

  I wish you a nice day.

  Thank you

  Domng

  Hi @Domng,

  Welcome to the HP Forum!

  Thanks for joining the community of the HP Forum.  It is a great resource for information, advice and solutions that have helped others. Here is a link as a guide should you have any concerns or questions about the process:

  First time here? Learn how to post and more

  I understand that you have installed Linux and your VGA port does not work.  HP does not support Linux but supports the hardware.

  Here is a link that can help:

  HP Notebook PC - Frequently asked Questions on Linux (FAQ)

  Good luck!

  If this post has helped you solve your problem, please choose "accepted Solution"to help other members and visitors locate that information. "  To say thanks for the help, please click "Thumbs Up icon" below.

• Connected to the Portege 3500 USB DVD burner is not recognized correctly

  I am trying to connect a burner DVD HP DVDv 940th my 3500.When Portege I plug in the device, it is not recognized and the Device Manager list as a storage of unknown mass without a driver. Where can I get this driver?

  Hello

  Try to check the assumption of the manufacturer or the download page. Manufacturers of portable gift use support external devices t produced by other companies.

• Router X 3500 how to connect to the printer HP C4180 of PHOSTOSMAR

  Good evening everyone,

  I am a newbe to this forum.

  I buyed the X 3500 router last week and I'm happy about it, but I don't know how to share my printer (HP PHOTOSMART C4180) by USB connection. You can connect to a printer to share. Indeed, this is posted in the FAQ section. How can I connect it?

  I hope you can help me.

  Best regards

  This

  Hi lestat2204, based on readings, there are only a few printer models that have been tested to work with the X 3500. You can check it from this link http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=924b2530e16c41f08e474610011092c2_List_of_tested_US...

  You can always go forward and try to install your printer once more just to be sure. You can follow the steps in this link http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=cc3da20d868948309be382b7b1202b06_KBxxxx_EN_v1.xml&...

  Hope that helps.

• Aironet 3500: Spectrum Expert Mode of connection

  How can I connect to a 3500 to see the analysis of the spectrum? The manual says to download version 4.0 of the software Cisco Spectrum Expert, but the latest version is 3.3.52. What Miss me?

  I want to make the most of these new APs!

  Thank you

  Andrew

  It is still Beta code.  Not only do you have the Beta code, but a key

  as well.  Once you have installed, you connect to your controller and

  change the mode of your AP - SE connect and reboot the AP.

  Then you go to the AP, copy another "key" in the AP and also

  collect the IP address if the DHCP.

  You paste the key into your Spectrum Expert running on your

  laptop, as well as the IP address of the AP.

  Then, you can remotely see your spectrum.

  I've done this before, because I tested a 3500 for a few weeks before

  refer to Cisco.

  I am impressed... It is definitely an interesting option.

• Nvidia card must be connected to CUDA Mercury acceleration?

  Before I go spend a bunch more money on display cards...

  Let's supposed I had an ATI 5870 driving 3 monitors... and I also had a 4000 Quardo installed... but connected to the monitors of no....

  First always see and use the 4000 CUDA cores to accelerate the performance of first?

  Briefing note 1

  I had already enough degradation of performance and hassle trying to run a 4870 + GT120... so I will try to avoid mixing the brand cards different monitors in 1 line system

  Briefing note 2

  I'm on a full charge MacPro Nehalem 2009

  No, Yes. There is no need to connect monitors to use the Quadro 4000 card. It requires however correct installation of the operating system.

  If you ask a question next time, do it in a clear and understandable way.

  Nvidia card must be connected to CUDA Mercury acceleration?

  N ° it must be installed, but not need to connect to monitors.

  First always see and use the 4000 CUDA cores to accelerate the performance of first?

  Yes. If properly implemented.

  Try to avoid the conflicting issues and create confusion.

• Security concerns about the external power supply connected to the my map of 9401 TTL inputs

  I have an external power supply (5V DC, 500 my) that I use to test my card 9401 count entries and check my LV code is working properly. Power + 5V is used as high signal and ground as a weak signal.  I haven't done the link yet because I wanted to know if there is any concern to burn my card.

  Hello

  Normally, if everything is OK, it shouldn't be a problem.

  But in the real world "things" happen

  My Advisor is to add resistance series (in this case 1 k) to protect your device if Murphy enters the room something goes wrong.

• Microsoft Wireless Mobile Mouse 3500 will not connect

  I use a(see title) and it refuses to connect. I've had this mouse for about a year now, and it worked perfectly. There is no cause to this problem that I see. The mouse is on and the blue light is showing small light under the Green Watch scroll wheel. The only problem is that the usb connector is extremely hot, but I think it's normal. Please help, I don't want to spend money on a new mouse when it looks very good!

  Hello

  1. what operating system do you use?

  2 are you able to use USB devices?

  3. have you tried to connect to other USB port?

  4. What is the State of the mouse in Device Manager?

  Step 1: Run the fix it tool in the following article and check.

  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/

  Step 2: Update the driversfor the mouse.

  http://www.Microsoft.com/hardware/en-us/downloads

• What I can (and if so, how could I) connect two encoders (a linear and angular) for the same chassis (NI 9401) and get their respective MAX OR tasks as simultaneously as possible?

  Sorry, but I'm still pretty new to LabVIEW and NI MAX I plugged the two devices (a linear probe and an angular encoder) for my NI 9401 chassis. I figured out how to create tasks for each and continuous readings of samples of each. Trying to run both in LabVIEW, I get the error message saying that I can't run several tasks at once. He suggests the control task VI, but I did not see any help. Any advice?

  Here is some general information, whatever it's worth: two encoders work the same clock source, PFI4, which, to my knowledge, is the CTR 1 A, where the the angular encoder signal is wired in. Physical channel linear is ctr0 and the angular is ctr1.

  Thank you very much for taking the time to review this issue and help me out!

  
  

• How to automate the SSH connection/commands on a series of switches PowerConnect 3400 3500 and 6200 series.

  I'm trying to find a way to automate the commands to send a series of switches (about 20) showing some configs and save the output to a file. The way I was trying to do was using plink and creation of a batch of files for her.

  Essentially, it would be something similar to the following.

  ECHO for /f % in (devices.txt) plink % l word of PAST of USERNAME-pw-v - m C:\Batch\commands.txt > output.txt

  To split the above command, looking for my ips in the devices.txt and made a "plink pw - username PASSWORD - v IP-l m - COMMANDS > OUTPUT" for each. The problem, I'm running is that the switches do not accept logins, they constantly ask for the user and the password again. Even when you try to put them in the commands.txt he will not accept the entry. I googled using plink with dell switches but there is nothing to talk about this problem.

  So my question is, is it possible to automate this sort of thing in a batch file? Or some way to automate a series of commands to a switch via SSH? I'm just not wan't do manually connect to each of them, carry out my orders, out, reconnect and repeat. I did it on cisco switches so I thought the process would be similar but I don't understand what obstacle I'm running in here. Ideally, I'd like to see how to do this via SSH but at this point, I am ready to accept almost any alternative (secure) to automate the sending of orders for my switches.

  I hope that all makes sense.

  Sorry, I haven't used before plink, so I'm not sure what to change to get this to work. In the past, there was another Member of the community who has been able to use expect to establish connections to switches and save configs.

  Linux.Die.net/.../expect

  It may be somewhat more than installation, but you can be able to make it work for your needs.

  http://Dell.to/1RONL3D

  Let us know

• PP CC blocks - perhaps in connection with Mercury Playback and AMD / HD6950

  I had a lot of instability with my set-up.

  i73770K - 32 GB of RAM - HD6950 2 GB - Windows 8

  Computer has been and is very stable in all but the first Pro CC.

  I have clean re-installed Windows 8 and Adobe CC.

  I'm going to regularize with beta drivers 13.4 and 13.6.

  I think it's directly related to mercury reading because when I disable GPU acceleration and will software only, it does not crushed, but even on this pretty good system, it will not play well and it is a bit slow hogging all my CPU unless I use a lot of deception low display resolution.

  I have projects that threat, so I need to get to where I can change something soon.

  I suppose that here are my options:

  $1 $$ buy a more recent video as a HD7950 card. Maybe a new card would help? Or maybe the AMD drivers are a few sketches or support open CL is simply too new?

  2. $$$ buy a Nvidia card. Is there evidence that the Nvidia support is more stable and more mature?

  3. change on my MacBook Pro with HD6750M. It will simply not be as smooth and quick that my office with portable fans will turn off and all that. I prefer to use my beasty office.

  4. $$$ bail and just go FCPX on my Macbook Pro. It seems ridiculous because I am paid upwards to the CC workflow.

  I'd go with 2.  Reported problems with the latest nVidia 320 driver, but using an older driver 314 it works petty darn good.

• Device USB 3.0, USB 2.0 connection ports of iMac

  USB 3.0 device not recognized: my iMac a 2011, 4 USB 2.0 ports.  I bought an external WD My Passport for iMac USB 3.0 external hard drive.  It is not recognized by the iMac.  The device works of WD - I plugged on new MacBook Pro from a friend and it worked in the USB 2.0 and USB 3.0 ports and on a newish iMac (I forgot to check the vintage).  How do I obtain backward compatibility so I can connect the WD USB 3.0 device to the iMac, USB 2.0 port?

  Data: operating system is current at El Cap 10.11.6. iMac (21.5 ", mid-2011) I've updated the installer of DW disk utilities, but that did not help.

  The device has been formatted as Mac OX extended (journaled) using disk utility. If not then of course it will not work, most drives come preformatted for need to be reformatted to work with your Mac and Windows boxes. BTW, have you considered buying a top quality case such as a Mercury Elite Pro (www.macsales.com), WD case aren't the highest quality and tend to have a high failure rate.