Connect NAS LAN device via ESXi host

Similar Questions

• I can't connect to the internet via my host after uninstalled antivirus software and restart

  I can't connect to the internet via my host after uninstalled antivirus software and restart it.

  I use windows xp on my host computer and all computers in my client. After that I uninstalled the free trial NIS version and restart my host, I lost the internet connection. Tried to restore with the restoration of the system, but when I restarted it, it said the system restore could not be made. I changed it then with my laptop and I can connect to the internet as the host.

  Hello

  This can happen if the uninstall process fails and leaves behind a Symantec registry value. See the following Symantec article.

  Unable to connect to the Internet after uninstalling Norton AntiVirus.

  http://Service1.Symantec.com/support/NAV.nsf/8d071816eedd7cac88256c0e005a96e5/751c3298ab99cf7188256d34006702e2?OpenDocument

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows?

  322756 (http://support.microsoft.com/kb/322756/ )

• Best practices for backup of vCenter device and ESXi hosts?

  Hello

  I have a new VMware environment based on 5.5 ESXi and vCenter Server Appliance. A few questions:

  • What is the best practice to perform the backup of the vCenter Server Appliance? I set up the camera with the embedded SQL Express database.
  • It's recommended to backup the ESXi host or is it easier to any re - install failure?

  Best regards
  ,

  Thor-Egil

  Hello

  You can use VMware VDP to backup your device of vCenter. It is included in essentials, standard, enterprise, and enterprise as well as licenses.

  I won't have backups of ESXi servers. Restore the backup would take more time that the deployment of a new ESXi.Only thing, you may want to consider is to enable logging remotely, so you can see why the hosts failed.

  Concerning

  Tim

• BlackBerry Smartphones has tried to update the device software, now unable to connect to the device via USB

  I tried to update my 8100 to the 4.5 software.  I first updated the desktop to 4.7 software, then tried to update the device, but the process has failed.

  Now, when I open the Desktop Manager it shows not connected to the device.  I can go to the properties of the device mamager and select the balckberry, but when I return to the destop eat it says no device.

  It seems that whatever I do, it does not recognize the usb device.

  The display on the 8100 is company information only text, no graphics or by phone, and it is virtually unusable.

  There are options on the screen for some applications, but if I choose them, it says app not found.

  Is there a way to force an update to it?  Or I poohed this phone?

  Thanks in advance

  Edit:

  I pulled the battery on the device it reboot and tried to return to a former Office Manager Update

  1. unplug BB from USB and PC. Restart the PC turned off completely.

  2. for BB, you'll charge back to the theme that was used on the device when you upgraded, which will normally give you a black and white screen. You must follow the instructions below.

  You will need to use JL_Cmder to wipe the device and then load the operating system on the device. Follow the instructions here:

  http://www.BlackBerryFAQ.com/index.php/How_do_I_wipe_the_BlackBerry_using_Jl_Cmder%3F

  If JL_Cmder does not work, follow this instruction:
  http://www.BlackBerryFAQ.com/index.php/What_to_do_next_if_Jl_Cmder_will_not_connect_and_wipe

• Connection to a device via Virtual Box

  Hi all

  I'm under LabVIEW 2015 in Windows 7 in a VM (virtual machine) on an Ubuntu machine.  I would like to connect a USB - DAQ device, but it seems to be coming up with an error on the connection that does not allow me to work with the device to the virtual computer.  The MAXIMUM East-88705 error and he said: "the specified device is not present or is not active in the system..." ».  Any thoughts on what I have to do to make it work correctly?

  Cheers, cirrus

  Nevermind - just realized that there is a two-step process to add the device.  You must select the ENTER twice to get the USB device appears correctly in the virtual machine.

  See you soon

• BlackBerry software please update link (or the BONES of BB10) connection to connect to a device via USB with Powershare BB10

  After reviewing many topics:

  https://supportforums.BlackBerry.com/T5/BlackBerry-link/BlackBerry-link-no-device-connected/m-p/2515...

  https://supportforums.BlackBerry.com/T5/BlackBerry-link/link-won-t-recognize-Q10-on-Mac/TD-p/2912982

  http://forums.CrackBerry.com/BlackBerry-link-F300/BlackBerry-link-Windows-8-1-cannot-recognize-black...

  I discovered that the problem of not recognizing device with link performed from USB (2.0 and 3.0) port with Powershare function.

  I don't think it was the problem of the computer (laptop) with this feature because it will be a trend now.

  So please update link or BB10 OS this link can recognize peripheral BB10.

  We look forward to good news from Blackberry!

  After the 10.3.0.1418 (sunk), now the link and my BB Q10 is connected!

  Thanks to the 10.3

• How to connect an external device via an Ethernet cable with iPad Air?

  I need to connet to my iPad, a digital mixing console THE Behringer X Air xr18.

  LLA WiFi connection e/s is not overall durin live so I need to use the Ethernet cable.

  You can not unless someone makes a dongle, but even in this case an application had to talk with the dongle do not believe that a dongle could add something like kernel as a new network interface which could access normal applications

• Cannot add ESXi host to vCenter Server

  Hello

  I created a home set up a VMware datacenter for study purposes. I currently have 2 virtual machines: an ESXi host with vCenter Server Appliance deployed on this subject.

  I configured the server vCenter through web interface device and I have connected using vSphere Client.

  I created a data center, but when I try to add a host, I get "ERROR: the request exceeded."
  Connection with vSphere client directly to the ESXi host works.

  I can connect using SSH to the ESXi host.

  I have disabled the firewall on the ESXi host.

  I have read many articles on the kbase but nothing helped me to solve this problem.

  You have any ideas?

  I finally got to understand.

  It seems like my vmware workstation is not connected to the esxi as a physical host in my local network host, and so I was able to ping it unit of vCenter Server (but it worked the other way around, and that's why I thought it was ok).

  After the connection to the physical LAN of VMware workstation settings, everything worked fine.

• ESXi hosts SBS 2011, clients lose network via VPN

  Greetings,

  We have an ESXi Server (in a lab environment) who perform a SBS 2011 and a Windows 2003 (Terminal Server).

  We have two locations, connected via a VPN IPSec (2 boxes of ClearOS).

  The ESXi host is located in building r. customers in the construction of an experience no problem at all.

  Customers in the building B often lose connectivity to network share. We also failed when copying data. Do not forget that the servers are located in the building and issues affecting only users in the B building.

  We noticed the event ID 2012 on the VM SBS 2011 event viewer.

  The two buildings are connected to a cable broadband 10 mb / 1 mb ISP.

  NOD32 Antivirus is installed on the two virtual machines

  Any help would be appreciated!

  Thank you

  Fred9777

  Hello

  There are a few things to look out for more such links. The following steps were made on W2K and W2K3, so that they are still applicable for you.

  (1) is the VPN capable to manage the packet being sent by site B MTU size, sometimes the MTU on VPN size must be less than the default value of 1500 set LAN. You can check this scathing your server with a command like

  ping f-l 1500

  If you get a message like "packet needs to be fragmented but DF parameter.

  You will need to reduce the size of the MTU TCP/IP in the client registry. Try to ping the server with a size of 500 bytes and see how it goes.

  (2) setting the server TCP/IP stack

  In the registry HKLM \SYSTEM\CurrentControlSet\Services\Tcpip\Parameters, create or modify value DWORD of TcpMaxDataRetransmissions. By default, it is set to 5, but I recommend double this value to 10. The TcpMaxDataRetransmissions value is the number of retransmissions of TCP of a data segment without acknowledgement of receipt on an existing connection. TCP retransmits data segments until they are acknowledged or until the expiry of this value. Basically, when a client does not meet a package from the server, the server will attempt to retransmit the packet until TcpMaxDataRetransmissions many times. By increasing this value, you give the customer more time to answer on the server, which will help improve the flaky connections or connections with latency or higher than normal packet loss.

  HKLM\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\KeepAliveInterval and HKLM\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\KeepAliveTime.

  Both entered DWORD.
  KeepAliveInterval determines the interval between retransmissions keep until a response is received. If a response is received, the delay until the next keep alive transmission is again controlled by the value of KeepAliveTime.
  The connection will be broken once the number of retransmissions specified by TcpMaxDataRetransmissions is remained. KeepAliveInterval is set by default at 1000, which is one second.
  KeepAliveTime controls how many times TCP attempts to verify that an idle connection is still intact by sending a living package of the Dungeon. If the remote system is still reachable and running, he will acknowledge receipt of the living transmission to keep. KeepAliveTime is set by default to 7 200 000, or 2 hours.

  I hope this helps.

• Connected to the ASA via the "VPN Client" software, but cannot ping devices.

  I have a network that looks like this:

  

  I successfully connected inside the ASA via a software "Client VPN" tunnel network and got an IP address of 10.45.99.100/16.

  I am trying to ping the 10.45.99.100 outside 10.45.7.2, but the ping fails (request timed out).

  On the SAA, including the "logging console notifications" value, I notice the following message is displayed:

  "% 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; "Connection for icmp src, dst outside: 10.45.99.100 inside: 10.45.7.2 (type 8, code 0) rejected due to the failure of reverse path of NAT.

  I have a vague feeling that I'm missing a NAT rule of course, but not all. What did I miss?

  Here is my configuration of ASA: http://pastebin.com/raw.php?i=ad6p1Zac

  Hello

  You seem to have a configured ACL NAT0 but is not actually in use with a command "nat"

  You would probably need

  NAT (inside) 0-list of access inside_nat0_outside

  He must manage the NAT0

  Personally, I would avoid using large subnets/networks. You probably won't ever have host behind ASA who would fill / 16 subnet mask.

  I would also keep the pool VPN as a separate network from LANs behind ASA. The LAN 10.45.0.0/16 and 10.45.99.100 - 200 are on the same network.

  -Jouni

• 5.5 ESXi host is not able to connect to the network

  I installed ESXi5.5 U2. But the ESXi host grab an IP address from the DHCP server. I tried givind static IP of my office network, but still unable to connect to the network. I checked the CLI, the vmnico of the adapter is in place. Why the machine does not have an IP address?

  I started this machine from the network (available in the bios settings) and observed if an IP address is required. Then, I started the server from the hard drive. Surprisingly, it took an IP and I could connect via the network.

  After that, I plugged this NETWORK adapter to a different location on the same server. I found the same problem (do not take IP). But when once again, I did the "Network Boot" thing, it took an IP address and now it works fine.

  What is average?

  Apparently, my problem is solved, but I still don't know the reason.

• Migrate the replication for patching ESXi host device

  Hi guys,.
  

  
  

  I'm trying to Storage vMotion/migrate vSphere replication device to different host for ESXi patches. I get the following message
  
  "This entity is managed by VR management solution. It is not recommended to edit it directly. Instead use the GPMC for the solution if you want to make changes. You want to proceed. "
  
  I use vSpere replication without the SRM device. What is the best approach to upgrade ESXi host where there is replication Appliacce. Should I just stop then move the unit, or is it possible to move it while it is running?

  
  

  Kind regards

  
  

  MQ
  
  

  Hello

  Moving the unit via the technology Vmware is perfectly fine.

  The message/warning you receive is just to warn you that this VM is a critic and you must be careful. The same message if you invoke the power out of this machine.

  Kind regards

  -Martin

• How can I migrate an ESXi host since a vDS in a vSwitch with NAS storage on vDS

  I need to move some on a vDS esxi hosts to a standard vSwitch to move a new vCenter ESXi hosts

  I have two 10 GB network adapters that manage the ports VM, NAS storage and vmotion.

  Is there a documented procedure to move a vDS in a vSwitch, particularly for migration from NAS storage to a vSwitch?

  Thank you

  Tom

  No, you will need to do this on a per-host basis.

  I really recommend doing one by one, not in a hurry and checking all the networking before you proceed to the next step. Example: after migrating the vmkernel interfaces, check on a ssh connection to the host if it can vmkping the NAS. Before you move all the virtual machines on the host to the switch std, move one and check if the VM networking continues to function. This will prevent errors and downtime.

• ESXi host have not of virtual machines when connected through vCenter

  Hi all

  I am facing a problem with 1 ESXi hosts. All other hosts are working properly.

  All hosts are managed by vCenter 5.1 VM. When I select this problematic host in vCenter and click on the virtual computers tab, it does not display anything other than a blank page. Then, it throws an error saying that the object has been deleted or has not completely created. The screenshot of the error popup is attached.

  However, if I connect directly to the host through the VI client, it does not throw the error and I can see the virtual machines it. If I have vmotion the vms during this host, I do not see these virtual machines via vcenter but I connect directly to the host and I can see the virtual machines. They work very well.

  What could be the cause of this problem.

  Thank you

  AG

  I would try restart the management agent on the host troubled or removing of vCenter and time.

• Single recovery of ESXi host disaster using boot USB device.

  Here's the scenario. I have an ESXi host 5.0 running from a USB device on a server blade using shared virtual machine network storage and is scratch storage. I have a failure catastrophic host. Can I just plug the USB device into another blade in the same chassis and start getting my VMs back operational.

  In addition, in a similar scenario if I have two devices USB with the same configuration information about them can use as a backup in case of failure of the USB device or is it config info constantly being written to the USB device which is used at the time.

  At the level of the configuration, you need not, this means that as long as you take a regular backup of the config, it is ok.

  But when you need to set up a backup system if a production system does not go and change the Server Blade, be sure to provide a coherent zoning and LUN masking for the blade, if VMware will see the same number of unit logic and tables as before. Same thing applies for VLANS, switches to which the new blade is connected must be configured in the same way that the old blade was (its ports must be in the same VLAN), or some VM can't see the network correctly.

  1. If a system is corrupt and you just need a fresh USB boot

  Plug a USB stick fresh, possibly already installed, boot, and then send the archived configuration, reboot

  2. If a full blade goes wrong, you must change the server.

  Put the WWNS of the HBAS in the same areas that the blade HBA has failed

  Present the WWN of the HBA to the storage group

  If you use the same chassis slotin, the network should be ok, but if not, put the internal ports of the switch module blade matches the new blade in the same VLAN as port internal used for blade failed.

  If you use VirtualFabric / VirtualConnect on 10GBE NICs, you must set up the same way, it was too much on the failed system.

  I hope that its more clear now!