Connection of Bluetooth Internet sharing

Similar Questions

• Laptop &: how to share internet connection via Bluetooth?

  Hello

  I recently bought a laptop and I can't find how to share internet via bluetooth from my desktop pc. I can connect using the personal area network (PAN), but I don't know how to send the internet. everything that I said try as much as all have failed.

  I do not know this questions been asked a lot, then I'm sorry to ask again)
  could someone tell me step by step installation?

  (Thank you, it is appreciated)

  Hello

  It s takes longer to describe the complete installation of the use of BT for internet sharing.
  I found this site with a statement of installation for Windows 2000.
  The dialog boxes for Windows XP may be a little different, but the configuration will be the same.

  http://www.Geekzone.co.nz/content.asp?contentid=1285
  However, check it out. It s useful.

• How to go from "offline" Mode when you use Firefox on an android device that is connected to the internet through Bluetooth.

  I have been using my tf300. Whenever I try to open Firefox on the Tablet while using a Bluetooth connection, the only screen that Firefox opens is a generic screen displaying 'Offline Mode '. Is there a way to switch to online mode or I am able to use the browser on a wireless signal?

  Could you clarify - are other applications can connect to the internet when you are logged in this mode?

• I am connected to the internet, but my network sharing Center proclaims that I'm not.

  The paradox connected but not connected

  I am connected to the internet, but my network sharing Center proclaims that I'm not. Because some of my programs believe later, they refuse to patch. Also, I used the antivirals ware, scans, System Configuration and deleted and later restored the wireless network.

  Any help would be greatly appreciated. Thanks in advance.

  Hello

  1 reboot as often, this allows the refresh icon and also stops a few things of
  interfere with the slot troubleshooting process.

  Do a 1 Restore Point then you can go back to where you were if necessary.

  How to create a Vista System Restore Point
  http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

  ------------------------------------------------------

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Do
  It will be the same for network (NIC) card - then right click on the devices and UNINSTALL - Reboot -
  update the driver stacks.

  Now go look at the site of the manufacturer of the system for the updated drivers.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -----------------------------

  Allow you to reset your TCP/IP stack just to make sure:

  Start - type in search - ORDER - search box at the top of list and RIGHT CLICK – RUN AS ADMIN

  Enter these one at a time (or copy and paste) and press ENTER after each

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int Reinitialis

  netsh int ip reset

  netsh winsock reset

  Reset

  ----------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT.

  ---------------------------------
  Other tips:

  If the use of a wired cable - Control Panel - device - network adapter - (NIC) Manager - double
  Click Advanced settings and set the "speed & Duplex" 10 Mbps full duplex and then try 1/2
  double-sided. Be sure to APPLY / OK. Maybe some help here: (don't forget the answer is)
  complicated because there's probably more than one single thing, the origin of the problem)

  Others.

  http://www.pctipstricks.com/tips-for-troubleshooting-network-cable-unplugged-error-for-wired-Microsoft-platform-PCs/

  http://www.how-to-hide-IP.info/2009/05/16/CYBERGHOST-VPN-fixing-network-cable-unplugged-error/

  http://www.annoyances.org/exec/Forum/WinXP/1109372091

  There are many causes, one of which is the small monitor pays attention to the evil network device.
  You can try to disable any other network such as WiFi device and reboot to see if that has an effect.

  Still a problem of equipment such as a loose network card that is not properly attached to the computer can
  cause this.

  http://compnetworking.about.com/od/WindowsNetworking/f/cableunplugged.htm

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Sharing - a printer is connected to a Mac using Airport Express to connect to the Internet.

  My Epson r320 is connected to a Mac using express airport more convenient to connect to the internet. I have a laptop by using Wins. Vista. I want to share the R320 with the PC. I created the Hello-sharing program. Pc reconizes the printer but will not be printed.  The Epson site directed me to your site. Help!

  Hello

  You must install the drivers for the printer on the PC using the add printer network in Control Panel, printers.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Smartphone blackBerry, connection to the internet using bluetooth

  Hello

  I have a laptop pro running with a Blackberry 8900 OS 10.6.2. I have the system of preferences under bluetooth DUN seller Motion with blackberry option IP Modem (CDMA) according to model, I chose research. The laptop can connect to the phone, but does not connect to the internet, any suggestions?

  Thank you

  Lambert

  Hello
  Just to keep everyone updated, I managed to make it work. I had to download a modemscript for the 8100. I set both of phone number * 99 #, user name and password for comments.

  Thanks for the support

  Lambert

• My center network and sharing, says I'm not connected to the internet, even though I'm

  Windows 7 professional 64-bit.

  Just got a new modem/router DSL which is wired connected to my office.  I have access to the internet by opening Internet Explorer my network and sharing Center says that I am not connected to the internet, even though I am. There is a red cross between my computer and the internet in the network and sharing Center.  Also, on the lower right part of my office internet connection symbol has a red x.  I had a home network before this new modem/router.  Now, I can't put my home network since the system says that I have no network connection.  How can I fix it?

  Hi cpark3,

  Thank you for writing to Microsoft Communities. The problem description, I understand that you receive a message from the network and sharing center that you are not connected to the internet. Provide the following information:

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Follow these steps:

  Step 1: Start the computer in safe mode with network and check.

  Startup options (including safe mode)

  Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.

  Method 2: Follow the steps in the article.

  Windows wireless and wired network connection problems

  How can I troubleshoot network card?

  So, you can read this article for more information.

  How to reset the Protocol Internet (TCP/IP)

  Let us know if you need more assistance. We will be happy to help you.

  Thank you.

• Portege R830 had dead blue when the screen connects to wifi or shared internet

  It seemed began as soon as the automatic update from Microsoft on Qualcomm, Atheros, every time when connect to any WIFi, share internet, my portege R830 shows blue screen and the following error message:
  unhandled system_thread_exception (athwb.sys)

  I found that I am not the isolated on the Web site. I tried to remove and stop updates. However, once I connect to the internet, the blue screen comes back.

  Is the problem because of the network adapter? The model is Qualcomm Atheros AR9002WB
  Can solve the problem if I download the new driver of Qualcomm-Atheros site? Or if I replace a new adapter?

  The athwb.sys file belongs to the Atheros wireless driver. Usually placed in C:\Windows\System32\drivers\athwb.sys
  It seems that in your case this file causing the BSOD.

  I found a very interesting detail about this problem and why it seems.

  A user wrote:
  {quote} The issue is due to a database hosted on Linux kernel mapped NAS drives and if the Client for NFS is installed on the windows machine. For some reason, this configuration does not work. If you mount your shares and NFS is installed it tries to use the NFS client and fails miserably. Trick is to disassemble all the shares of logging in Safe Mode and then rebooted and uninstall the NFS client and then mount your shares. {quote}

• On a shared PC my side do not connect to the internet but side not affected spouse. I have run virus scan and none detected on its side but can't run on my side, because I can not connect help please.

  My husband and I share a PC. He has his desk top and I have mine, just that recently, I have not been able to connect to what anyone on my side of the PC, but its East side works well, it can connect to the internet, but I can't any idea what should I do? I ran virus scan and his side of own, cannot check the mine but cannot connect help please.

  Hello

  1. you remember to make changes to your computer, after which the issue started?
  2. do you have a cable or a wireless connection?

  I would recommend that you follow these steps.

  Step 1:

  Test the issue in safe mode with network and check if that helps.

  Step 2:

  Configure the connection to obtain an IP address automatically.
   
  a. click "Start", enter "NCPA. CPL"(without quotes) in the search bar and press"Enter. "
  b. right-click on the network connection, and then click "Properties".
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  c. click Select 'Protocol Version 6 (TCP/IPv6) Internet' and then click 'properties '.
  d. check "obtain an IP address automatically" and "Obtain DNS server address automatically".
  e. click 'OK '.
  f. click Select 'Protocol Internet Version 4 (TCP/IPv4)' and then click 'properties '.
  g. check "obtain an IP address automatically" and "Obtain DNS server address automatically".
  h. click on 'OK '.

  Step 3:

  Follow the steps in this article and check if that helps.

  Why can't I connect to the Internet?

  Steps are also applicable for Windows Vista.

• HP mini 110-3601TU unable to connect to the internet

  I'm under the netbook with Windows7 32-bit with Service Pack 1 Starter Pack. The PC connects to the internet eventhough bluetooth and Wi - Fi indicate that they are not cancelled.  Try to connect with HP Quickweb is possible, however.  So, there's something wrong with Windows7.

  1. the network and sharing Center says "not connected".  Basic network information display and game connection - "Unknown, dependence and the group could not start.

  2. run Network Diagnostics in windows - "Troubleshooting couldn't identify the problem.

  Run the diagnosis mode in advance - "Windows could not automatically detect the proxy network setting.

  3. checking the adapter - Broadcom 4313 802.1 1 b/g/n, the device works correctly (as I mentioned, I can connect through WiFi to internet through HP Quickweb).

  I suspect that there could be a registry problem with dhcpcsvc. DLL file.  I thought to reinstall Windows7 by using the original installation media, but I was not provided with one when I bought the camera.  How can I get hold of this?

  Hello

  As it appears, you can have multiple OS files damaged, probably the best solution is to reinstall.  Before you try the following, make sure to back up all your personal files etc.

  I realize that you do not have your recovery media, but you should still be able to reinstall the operating system from the hard disk recovery Partition.  You can try this as follows.

  Shut down the laptop.  Here tap f11 as soon as you press the power button to see if it will run Recovery Manager.  If this is the case, follow the instructions on the link below under the heading ' restore the PC to its original condition with HP Recovery Manager Windows 7 " but are starting to point 3 you hired Manager option f11 recovery."

  http://support.HP.com/us-en/document/c01895783

  Kind regards

  DP - K

• Unable to connect to the Internet my Satellite L300-1 to 6

  Hello

  I have a problem with my Satellite L300-1 to 6. When I try to connect to the internet I plugged taking LAN my slot for LAN card and when the identification process of the network in "Network and sharing Center" to the State of the connection write "Unindeficated Network" and I cannot access the internet...
  And this is happen when I use automatic receives the IP parameters... ?

  When I try to solve this problem with the manual configuration TCP/IP settings in the status bar indicates that I have an internet connection but when I try to open the WEB site I see the error message «...» CAN NOT COMMUNICATE WITH THE SYSTEM (DNS).

  Please explain to me how to fix this...?

  P. S. The network on my other PC works normally... ? On my L300, I use Windows Vista Home Premium SP2 and on my other PC, I use Windows XP Pro... ? !

  Hello

  Usually, the WLan router supports a range of IP addresses and everything should be set to automatic.

  In my opinion, you should first check the settings of the WLan router.
  Take the router manufacturer news and read the manual of the router how to set up the router.

  After the router has been configured correctly, you should go to connections-> LAN (local network connection) and need to access the properties of the TCP/IP protocol.

  Here, you must make sure that the IP address and DNS are set to obtain an address automatically

  That's the whole secret.

• Satellite Pro M70: How to connect to the internet using a second computer

  I have a Toshiba laptop Satellite Pro M70 with a RTL8139/810 x Family Fast Ethernet NIC use this, the laptop was connected to a desktop PC, whereby it is connected to the internet via a modem ADSL (USB) on the desktop. The laptop runs XP Pro; the desktop has XP Home.

  My laptop has been a nasty virus. When removing it, he lost the ability to network. I tried "repair network", but he could not find an IP address. In the end, I had to manually set an IP address for the network to work again. You use IPCONFIG release and renew the IP addresses that failed - unable to connect to the DHCP server.

  He could now see the Office network and Exchange files across be it, but it could no longer contact internet.

  I decided to reinstall the OS on the laptop, but this does not solve the problem. I still have to manually set the IP on the laptop. I can connect two PCs, but does not see the internet from the laptop on the network.

  If I connect the laptop directly to the internet via the modem, it works fine. I can even access the internet from the computer on the network when this is the laptop that has the internet connection.

  The virus could have damaged the Ethernet controller, or she affected somehow?

  Is it possible to test?

  Have you advice?

  Hello

  The virus was detected on the laptop you so maybe your PC has also been affected.
  Did you check if the laptop and the PC using the same workgroup?

  XP supports a help option. There, you might choose the Internet Connection Sharing Troubleshooter. "

  Maybe it helps

• Toshiba 40TL938 unable to connect to the internet

  Hello

  Just bought a Toshiba 40TL938. The only problem is that it does not connect to the internet.

  I have tried both wireless and wired, it connects, gets an IPaddress, appears on my router... but when you test the connection fails. I have connected many of the AP, still the same problem. Also it plugged into my HTPC and shared the internet connection. There also, he shows up, he gets the IPaddress and after that nothing.

  The first "Toshiba Places" lights up briefly and I managed to get. Everything has worked, but with each query, it displays: error connection., while I could use every option available, tvshows of flow and trailers etc. While displaying a message, it was not connected.

  The only weird thing I've noticed is that in each switch/router and PC the networkname of the Toshiba 40TL938 is not displayed.

  Help, please!

  Well, internet connection should not be a big problem.
  I mean, it's the whole procedure step by step is described in the user manual.

  I think that's not problem TV but you have a few problems with the configuration of the router.

  Is that you do not need to configure all the settings if you are using a LAN connection.
  Your router must support DHCP. The router supports a pool of IP addresses that are assigned automatically to a device connected to the router.

  I would recommend resetting the TV as well as the router.
  Make sure that the router is configured properly, and then follow the procedure step by step, as described in the user manual.

  I also recommend you to read another thread on the WiFi for a Toshiba 40RL938 Smart TV
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=71869

• Satellite L20: Unable to connect to the internet using mobilephone & dongle BT Mecer

  Hi all

  Mine is an edition of Satellite L20.
  I recently installed XP Professional Service Pack 3. I connect to internet using my USB cable with my Sony Ericsson C702 (use the phone as a modem).

  Since there is no bluetooth built into my laptop.
  So, I bought a Mecer bluetooth dongle. I installed the bluetooth software. Can I transfer data between my laptop and my mobile phone via bluetooth.

  Now the problem is I can not connect to the internet via bluetooth. I opened my bluetooth IVT software and paired my laptop and mobile computer. Then I opened my Sony ericsson suit and looked for my mobile finds, my mobile and still once he pairs with my cell phone and when he tries to connect with my mobile phone its shows "device cannot be detected, try again." I tried to reconnect, not matching and pairing it several times, but no use.

  I also found one thing, just after it displays "Device cannot be detected," a pop-up message "SEPCSuite.exe has encountered a problem and closes the window with options."
  1) send to microsoft
  Including 2) send.

  What can we do to fix this problem?

  No idea...?

  See the website of your provider of Bluetooth software to help. This forum is for Toshiba Software only.

• Satellite PSCBWE C850-1MD - cannot connect to Bluetooth

  I have a Toshiba Satellite C850-1MD purchased PSCBWE but I can't connect to Bluetooth mobile phones.
  On the internet, I realized I had to install a control because my Realtek WLAN's.
  What I've done.

  Then, they say on the site Web of Toshiba that I need to download a system driver, but I can't find my computer?

  Where can I find this works and the bluetooth feature, anyone?

  + The message was edited: translated by Google Translator.

  The laptop can't stand BT and this is the reason why you are unable to connect the mobile phone via Bluetooth ;)