connectivity between 5508 and two different 4507 switches

Similar Questions

• How to connect Apple TV to two different amplifiers?

  How to connect Apple TV to two different amplifiers?

  If you're talking about AppleTV 4 then there a single HDMI output only.

  You need either a HDMI switch or a divisor of direct HDMI to different amps (may not work at the same time due to HDCP) or see if an amp offers HDMI or optical output to the other depending on whether or not you want to distribute audio or video to the 2 amp.

  If you need a splitter/switch, it's an extra box and you might consider only 2 AppleTV, don't forget a rental on one will not be seen on the other.

• Bluetooth connection between iPhone and iPad

  My iPhone 6 does not connect to my iPad via bluetooth.

  I previously used the bluetooth connection between my iphone and iPad to connect the iPad to the internet. Despite the two devices were among the recognized bluetooth devices and they were previously linked/partner, it was not possible to establish a connection.

  Perform the actions recommended for repair/reissue apple support - 1. Toggle bluetooth, 2. turn on/off the unit, 3. remove the iPhone/iPad bluetooth connections - 4. Reset network settings - 5. Reset all the settings-, nothing works.

  IPhone/iPad devices isn't even on the list of bluetooth devices available on the iPhone, or iPad. Everything that happens is the animated icon turns all the time.

  Deleting a connection to a device and bluetooth speaker/amp from the pairing of the speaker/amp system process made a new connection.

  iPhone 6:

  Model: MG4F2QN/A

  SN: C31NLG8KG5MR

  Version: 9.2 (13 c 75)

  iPad:

  Model: ME898LL/A

  SN: DLXM42LHFK13

  Version: 9.2 (13 c 75)

  Please give instructions for the previous maintenance work bluetooth connection between iPhone and iPad.

  Thanks in advance

  To use the Hotspot feature (that you described for the connection), you must use the instructions below.

  Share your Internet connection with Personal Hotspot - Apple Support

• Localhost UDP connection between FCR and Matlab

  Hi all

  I have a question about the connection between Matlab and FCR UDP. My idea is to Exchange data between Matlab and Labview on the same computer.

  So I found the 'UDP Simple' of the FCR 2.0 sample project where periodically a datasample is generated randomly and sent to the remoteport 61557 local host. In the project a 'fractional number of string for transmission' is used for the transmission of data. The receiver of the sample project reads from the same port to receive the datasample.

  Now, I'm interested to read this simple stream from Matlab (just at first), however, it does not work and I'm not sure why. What I do in Matlab is the following (code Matlab)

  delete variables;
  u = udp ('127.0.0.1', 61557); % Of installation UDP Object
  fopen (u); open reading port %
  A = fread (u, 1);  % read an element
  fclose (u);

  With this code, however, I get a timeout by saying: "' WARNING: unsuccessful reading: the amount of data specified has not been returned within the time limit." "

  I'm not sure why this happens, maybe you could help me out here? I guess that the formet serving to VCF is not the same as in Matlab? Maybe the Terminators are not the same?

  See you soon,.

  Steve0

  Hey

  So, regarding the problem actually, I found the solution today. It was not the firewall, but a simple configuration in Matlab seting the UDP port. So the side of Matlab, to change the definition of udp object according to

  u = udp ('127.0.0.1', 'Thelocalport', 61557);

  If you have

  u = udp ('127.0.0.1', 'Thelocalport', 61557);
  fopen (u);

  A = fread (u)

  fclose (u);
  Delete (u);

  Who does the trick and you can read from the port. Then of course you say Matlab that you read from the "LocalPort" x, which I wasn't aware of.

  On the transmitter side, you simply:

  u = udp ('127.0.0.1', 61557);

  fopen (u);

  fwrite (u, '1');

  fclose (u);
  Delete (u);

  Here, you set just the port of transmiting.

  About the format of the data: I used the simple UDP protocol streaming Comms project where a random number is generated as a double, transformed into a string (ASCII values) and transmitted. At the level of the receiver, you get as much the UDP packet with the ASCII values that you must turn if you want to find the number.

  I hope this helps anyone having the same problem.

  See you soon

• Establish a persistent connection between client and server

  My application must keep in touch with my servers, the HTTPConnection gives the ablitity to make one request per connection. Then the HttpConnection might not make persistent connections in the BB. I think I can use Socket connections. I am wonding if some body can confirm that and give some sugustions how persistent connections between clients and servers.

  Thank you RexDoug and Marchywka. Your suggestions are appreciated.

• dblink oracle to postgres with dg4odbc. ORA-28500: connection between ORACLE and a non-Oracle system returned this message: ORA-02063: preceding line

  Hi, I am creating the database link from a database of Oracle 11 g PostgreSQL with DG4ODBC and unixODBC

  My configured for /etc/odbc.ini

  [PostgreSQL]

  Description = Test to Postgres

  Driver = psqlodbc

  Trace = Yes

  Trace file = /tmp/sql.log

  Database = danieldb

  ServerName =

  UserName = SA

  Password = password

  Port = 5432

  Protocol = 6.4

  ReadOnly = No

  RowVersioning = No

  ShowSystemTables = No

  ShowOidColumn = No

  FakeOidIndex = No

  My configured for /etc/odbcinst.ini

  [ODBC]

  CommLog = 1

  Debug = 1

  FileUsage = 1

  Layout common = No

  Trace = 1

  [psqlodbc]

  Description = PostgreSQL ODBC driver

  Driver=/usr/lib64/psqlodbcw.so

  CommLog = 1

  Debug = 0

  FileUsage = 1

  My configured for /u01/app/oracle/product/11.2.0/xe/hs/admin/initPostgreSQL.ora

  HS_FDS_CONNECT_INFO = PostgreSQL

  HS_FDS_TRACE_LEVEL = 0

  HS_FDS_SHAREABLE_NAME = /usr/lib64/libodbcpsql.so

  Set ODBCINI=/etc/odbc.ini

  My configured for /u01/app/oracle/product/11.2.0/xe/network/admin/listener.ora

  Listener =

  (ADDRESS = (PROTOCOL = TCP) (HOST = oracle-poc)(PORT = 1521))

  SID_LIST_LISTENER =

  (SID_LIST =

  (SID_DESC =

  (SID_NAME = PostgreSQL)

  (ORACLE_HOME=/u01/app/oracle/product/11.2.0/xe)

  (PROGRAM = dg4odbc)

  (ENVS="LD_LIBRARY_PATH=/usr/lib64:/u01/app/oracle/product/11.2.0/xe/lib')

  )

  )

  My configured for /u01/app/oracle/product/11.2.0/xe/network/admin/tnsname.ora

  PostgreSQL =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP) (HOST = oracle-poc)(PORT = 1521))

  (CONNECT_DATA =

  (SID = PostgreSQL)

  )

  (HS = OK)

  )

  I'm trying to created public database link:

  CREATE DATABASE LINK PUBLIC 'orapos' CONNECT to 'HIS' IDENTIFIED BY 'password' USING 'PostgreSQL ';

  When I used tnsping

  [root@oracle-poc admin] # tnsping PostgreSQL

  AMT Ping utility for Linux: Version 11.2.0.2.0 - Production on May 16, 2013 20:34:19

  Copyright (c) 1997, 2011, Oracle.  All rights reserved.

  Use settings files:

  /U01/app/Oracle/product/11.2.0/XE/network/admin/SQLNET.ora

  TNSNAMES adapter used to resolve the alias

  Try to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP) (HOST = oracle-poc)(PORT = 1521)) (CONNECT_DATA = (SID = PostgreSQL)) (HS = OK))

  OK (0 msec)

  and finally, I try to use the database link:

  "SQL > select * from tabel2"@orapos ".

  2;

  Select * from 'tabel2"@orapos '.

  *

  ERROR on line 1:

  ORA-28500: connection between ORACLE and a non-Oracle system has sent this message:

  ORA-02063: preceding the line of ORAPOS

  What wrong with my setup?

  Thank you and best regards,

  Daniel

  Daniel,

  The problem is that you are using the ODBC Postgres driver for the HS_FDS_SHAREABLE_NAME parameter, but this must be an ODBC driver manager and not the driver ODBC Psotgres.
  Go to the.

  http://www.unixODBC.org/

  Click the 'Download' and follow the instructions to download the 2.3.1 pilot and make libraries and programs.

  Once this is done, then use the driver as parameter HS_FDS_SHAREABLE_NAME Manager, for example-

  HS_FDS_SHAREABLE_NAME =/home/odbc64/unixODBC/2.3.1/lib/libodbc.so

  Depending on where you install it.

  Kind regards

  Mike

• Connection between servers and opening default home

  Question about cross-server logon, if a customer has changed their rules of routing so that the default value at the opening of "wishes" is no longer used and a different call handler is used instead, will be this connection between breaking servers? Looks like that connection between servers using backdoor functionality (# and some numbers) which works with the 'Opening of wishes' system, I understand this right?

  No, it is not hardcoded to opening greeting Manager of appeal, but he needs to finish a greeting (whether for a Subscriber or call handler) - the logic is handled in the PHGreeting conversation (the guy that is used for the treatment of the call manager/subscriber wishes) - so if you have a routing rule that say, load the sign the Subscriber in conversation, then you're going to break.

  But as long as the call is handled by _some_ greeting, the hand of logic should work because the conversation PHGreeting is looking for a specific series of TTS to indicate that it is a grip of calls.

• JMS connection between glassfish and OSB

  We are having architecture where between GlassFish and OSB JMS messages. I have the following questions of design
  (1) what is the best way to send messages between these two App servers? (I mean use the JMS bridge or regularly use JNDI lookup and send the message and so on)? We want to send messages in both directions between these two App servers.
  (2) how we use JNDI search inside glassfish for OSB. We use an approach by providing the full client jar fat weblogic. (53 MB) Is this the only way? Is there any thin weblogic client that we use for queue search OSB of glassfish?
  Thanks in advance.

  Using a JMS client WL on GF has limits on XA/JTA, consuming messages from distributed locations and securing individual destinations. Workaround for the latter is to avoid to set ACLs on WL destinations and use SSL to encrypt network traffic if you wish.

  I recommend the following general method: (1) avoid using WL JMS on the GF level clients if you need exactly once the e-mail or require the consumption of a distributed destination and (2) use OSB or WebLogic foreign seller JMS integration facilities for either (A) bridge/transfer messages between WL JMS and GF JMS or call (B) GF JMS directly the WL/OSB tier.

  If you don't want to use a jar full of WebLogic as a customer, there is a pot of customer 'thin' t3 equivalent available in the latest version. I recommend the full jar unless a small pot size is an important condition in your use case. I recommend the thin 't3' jar on the thin "wl" pot as the pot thin t3 tends to have much better performance. Or the other of these clients can interact with older versions.

  FAQ for vendors integrating a Remote JMS summarizes the Server WebLogic tools available for the integration of foreign suppliers (http://download.oracle.com/docs/cd/E14571_01/web.1111/e13727/interop.htm#JMSPG553). I'm not familiar with a tool equivalent/layers of OSB.

  The stand-alone Clients documentation lists different JMS (http://download.oracle.com/docs/cd/E14571_01/web.1111/e13717/basics.htm#SACLT122) client options.

  Kind regards

  Tom

• How to use the modules of the series and two different bitrates in FPGA mode on cRIO 9075

  Hello

  I have a project with modules namely NI 9227 (module 1) and NI 9234 (2 Modules)

  The project is running and I use the file writing PDM and found that two channels is in the TDMS file while I download the file using FTP the cRIO.

  1 - my quesition is the addition of a second rate in the FPGA?

  2 - Why is it TDMS connect 6 channels and 4 channels?

  Thank you

  Attached to the project with two screws

  Hello Ihab,

  Sorry for the late response here; just saw this message! If you want to keep synchronized modules then definitely stick with the master configuration and slave for your two modules. Note also that you can taste a little faster with the NI 9234 as your master module (since its time base main internal is 13,1072 MHz instead of the time base of the 9227 12.8 MHz).

  Also, see the tips and information in our troubleshooting guide for the synchronization of the series C with LabVIEW FPGA modules:

  http://zone.NI.com/reference/en-XX/help/373197D-01/target6devicehelp/sync_acq_multiple_modules/

  I hope this helps!

• Ad hoc connection between XP and Android

  How can I set up a wireless ad-hoc, with shared Internet access, between a Windows XP computer (connected to Internet) and an Android device?

  Hello

  You can see the following link.

  How to create an Ad hoc network using Win XP

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-computer-to-computer-ad-hoc-network?SignedIn=1

  Note: also applies to Windows XP as well.

  Please provide us with more information on the Android device and the version of operation.

• Connectivity between Interconnect and Nexus 2000 fabric options

  Hello

  I would like to know what models of fabric nexus 2000 Extenders can I use if I want to connect them to a pair of interconnections 6248UP fabric in a FEX deployment, so I can move between blade and rack servers service profiles.

  Thanks for your replies.

  Christian

  Christian,

  Take a look at this guide.  It should answer all your questions:

  http://www.Cisco.com/en/us/customer/docs/unified_computing/UCS/c-series_integration/ucsm2.0.2/b_UCSM_202_C-integration.html

  Kind regards

  Robert

• Connection between mac and PC

  Why can't connect between computers PC under Windows 7 and Mac computers on my network equipment?

  without knowing what you have tried and this error message you receive, impossible to
  say. site Web as http://www.wikihow.com/Add-a-Mac-to-a-Homegroup might help.
   
   
  Barb
   
   
  http://digitalmediaphile.com/
   
  Application Windows 8 Blog Reader of Barb connected world - http://apps.microsoft.com/windows/en-us/app/barbs-connected-world-blog/02f35769-52bf-461c-b1d5-06e54a58d298
   
  Please mark as answer if that answers your question
   
   
   
   

• Network connections between VM and host is slow?

  I have problems with the speed between the host and the VM, connections is limeted and very slow. I'll open the file and copy and it's slowly. My OS is VISTA Business and VM on XP SP3. Connection between VM card is limited to me and see that trafficking is not very practical. If this can be rectified and speed up the connection between the virtual machine and the host.

  As I have written, you can use both at the same time. Just add a host connection only to the guest and make sure name resolution, host name (and the name of the client to the host) using the IP addresses assigned by DHCP VMWare Server for the host only (VMnet1, default) connection. The file "\system32\drivers\etc\hosts" ensures that this connection will be used, for example.

• Heterogeneous connection between Oracle and Postgres.

  Hi all
  
  I am trying to connect heterogeneous Postgres and Oracle for a few days, but I've always seen this error: "loss of the RPC connection.
  
  First of all: I use Windows 7, Oracle 10 g and PostgreSQL 8.4.
  
  I did the following:
  
  (1) create a system DNS named "PG". (The connection test is OK)
  
  (2) to create the file 'initPG.ora' in ' $ORACLE_HOME/hs/admin:
  # This is an example of initialization file of the agent that contains the HS settings
  # needed for an ODBC Agent.
  
  #
  # HS init parameters
  #
  HS_FDS_CONNECT_INFO = PG
  HS_FDS_TRACE_LEVEL = WE
  
  #
  # Required for the non-Oracle system environment variables
  #
  #set < varenv > = < value >
  
  (3) configure the file 'listener.ora' (in ' $ORACLE_HOME/NETWORK/ADMIN "):
  SID_LIST_LISTENER =
  (SID_LIST =
  (SID_DESC =
  (SID_NAME = PLSExtProc)
  (ORACLE_HOME = C:\oraclexe\app\oracle\product\10.2.0\server)
  (= Extproc PROGRAM)
  )
  (SID_DESC =
  (SID_NAME = CLRExtProc)
  (ORACLE_HOME = C:\oraclexe\app\oracle\product\10.2.0\server)
  (= Extproc PROGRAM)
  )
  (SID_DESC =
  (SID_NAME = PG)
  (ORACLE_HOME = C:\oraclexe\app\oracle\product\10.2.0\server)
  (PROGRAM = hsodbc)
  )
  )
  
  LISTENER =
  (DESCRIPTION_LIST =
  (DESCRIPTION =
  (ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC_FOR_XE))
  (ADDRESS = (PROTOCOL = TCP) (HOST = Cédric-PC)(PORT = 1521))
  )
  )
  
  DEFAULT_SERVICE_LISTENER = (XE)
  
  (4) set up the 'tnsnames.ora' file (in ' $ORACLE_HOME/NETWORK/ADMIN "):
  XE =
  (DESCRIPTION =
  (ADDRESS = (PROTOCOL = TCP) (HOST = Cédric-PC)(PORT = 1521))
  (CONNECT_DATA =
  (SERVER = DEDICATED)
  (SERVICE_NAME = XE)
  )
  )
  PG =
  (DESCRIPTION =
  (ADDRESS = (PROTOCOL = tcp) (HOST = Cédric-PC)(PORT = 1521))
  (CONNECT_DATA =
  (SERVICE_NAME = PG)
  (HS = OK)
  )
  )
  
  EXTPROC_CONNECTION_DATA =
  (DESCRIPTION =
  (ADDRESS_LIST =
  (ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC_FOR_XE))
  )
  (CONNECT_DATA =
  (SID = PLSExtProc)
  (PRESENTATION = RO)
  )
  )
  
  ORACLR_CONNECTION_DATA =
  (DESCRIPTION =
  (ADDRESS_LIST =
  (ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC_FOR_XE))
  )
  (CONNECT_DATA =
  (SID = CLRExtProc)
  (PRESENTATION = RO)
  )
  )
  
  (5) Finally, I create my DB-Link and test it:
  CREATE DATABASE LINK 'CENTRALE_POSTGRES' CONNECT TO 'user_login' IDENTIFIED BY 'user_password' USING "PG";
  
  SELECT * FROM 'dual"@CENTRALE_POSTGRES;
  
  I got this error:
  ORA-03135: interruption of the RPC connection.
  
  As you can see, I have activated the trace level (HS_FDS_TRACE_LEVEL = WE), but the still empty directory ' $ORACLE_HOME/NETWORK/trace.
  
  Any ideas?
  
  Concerning

  the alias PG tnsnames.ora is wrong — you must have 2 closing brackets after the so that HS SERVICE_NAME = OK is outside the CONNECT_DATA as:

  PG =
  (DESCRIPTION =
  (ADDRESS = (PROTOCOL = tcp) (HOST = Cédric-PC)(PORT = 1521))
  (CONNECT_DATA =
  (SERVICE_NAME = PG))
  (HS = OK)
  )

  You should know also HSODBC to release 10.2 was desupported since March 2008 and it was replaced by its product follow-up DG4ODBC V11

• Connection between PC and Photo Frame WiFi digital Journe Air 1000

  Hello
  I'm trying to use the wifi feature to transfer files between my computer and the Journe Air 1000. The manual is useless and there is no option in the image menu.
  I connect to my router broadband flawless and can read RSS, listen to the radio on the internet etc. The image does not appear in my network (Windows XP SP3) locations.
  Can someone help me?
  Thanx

  Hello

  In the manual, I found this:

  + Services + compatible WiFi using
  + 1. After turning on the unit, press or press the button (see manual for signs of button) on the remote control to switch to WiFi mode. +
  + 2. Press the arrow up / arrow down button on the remote control to select a service you want to use and then press OK or press OK on the remote control or. +
  + 3. Shows a message asking to connect to an access point. Confirm the task, then a list of WiFi stations available.
  + appears on the screen. Select a station and press OK or press OK on the remote control to start the connection. +

  I also find that this device supports IEEE 802.11 b/g connectivity with WPA/WPA2-PSK encryption.
  If you must make sure that your router Cela would support too!

  But to be honest that I put t think you might transfer the files using the WiFi network.
  The chassis accepts RSS, Flickr, Picassa, and Radio services.
  I did, t find any info about the file transfer via a WLAN.