Connectivity between 8.0.3.6 and 10.2.0.4

Similar Questions

• Impossible to establish a connection between microsoft router, modem, motorola and dell/windows xp computer

  I have not set up a connection between my computer dell/windows XP, Microsoft router and my Motorola modem. After reading the instructions for the router and set up like it says anything I've set up my computer say it is connected but is not really plugged. My ipod says that there is this WiFi but when I try to access the internet on it, it gives me a message saying "unable to connect to the internet, there no connection detected." The only time where I have Internet on my computer is when I unplug the Ethernet to the router and modem and have the modem only connected to one computer. This problem is can cause because my modem is configured with a cable from cox and not connected to a phone cord? (My router is a Microsoft Broadband networking Base station wireless MODEL: MN-500) (My modem is a modem cable Motorola surfboard implemented with internet helmsman) (My computer a DELL Dimension E521 with a windows XP service pack)

  SP3 is on it? Wireless is enabled on the router? Try this

• Connection between 1510 all-in-one and my laptop

  I just bought the above printer, but it was sold without a connection between my computer and the printer cable. However, my printer previous 2050 all-in-one who died has what appears to be a similar cable but I can not get the impression of working with her. Do I need a new connection? and why?

  Thank you for your help but I took the advice of a previous writer who is returned to the supplier.

  He sold me a rope he was sold as a matter of course with all the printers of this group number. The printer costs R700 and the R68 cord so not a bad deal

• How to set up a wireless connection between my computer windows 7 and my printer?

  Laptop running windows 7 and HP wireless printer.

  What printer wireless HP do you have?

  Is the printer connected to your wireless network and online?

  If so I just used the software provided from HP who asked me if I wanted to connect to a USB port or wireless router. I choose the option Wireless for my HP J4680 AiO device and the software installed the driver appropriate printer and other associated software, IE. Center solutions HP, etc and I could use my wireless printer.

  Click here to download manuals updated, how - to, of, software, drivers, etc for your machine.

  http://welcome.HP.com/country/us/en/welcome-copy.html#support

  If your printer is not connected to your network, you may need to set up a temporary ad hoc wireless between the printer and a PC. Once you do this, you can enter the printer wireless configuration pages and configure the SSID of the network, wireless, encryption type, encryption key, etc.. Also, FWIW, I have set my HP machine with a static IP address to make it easier for me to access any pages of any PC on my network config.

• Establishing connection between PC through GPIB-USB_HS and AQ6315-E

  Hello

  I couldn't create connect with spectrum AQ6315-E max. For "scan for instrument" request Max returns "Instrument not found."

  GPIB-USB-HS about what - it's 100% working properly. Some problems with GPIB analyzer - port could be? In addition, the Analyzer have 2 GPIB port. But it is indifferent for MAX - port which is connected (it shows that "instrument not found" in both directions). What should be the reason for this?

  I thank the of for attention. I found my miss. The GPIB-USB-HS and analyze the same GPIB card - address. When I specified one for parser - MAX reveal properly connected Instr.

  Thank you.

• Cannot restore the connection between the computer wireless laptop and printer

  I have a Photosmart 6510 and a HP laptop computer connected wireless.  They worked together wonderfully since a few months ago, I installed the printer.  The wifi was briefly in standby.  When I sleep and tried to print I get an error message that the printer is not found.  The printer indicates that the wifi is on (blue light is on and the internet window shows that it is connected ad gives all network information, including the IP address.  I tried all my usual electronic bugs: turn the printer off and back on, unplug the printer and let it rest, reboot the laptop, etc.   I am running Windows 7.  With my old HP printer, I get an error message when the printer is offline, that would allow me to go to a "fix" and click to get back online.  I couldn't find this option now.

  Nothing works (the mobile web access so I know it is related also).

  Are there other things I can try before I have to go through the hassle of reinstalling the printer?  I hope there is an easier difficulty.

  And, if I have to reinstall it, I have to write it?

  Thank you.

  I fixed it.  I unplugged the router and the modem, plugged them back in and click on the reset button on the router and the laptop and printer now talk to each other once more.

  There is a problem with this laptop.  Before even I had a wireless printer, I have everything reset completely to the laptop if there is a power failure (but not to the modem in stanby mode).

  My second question is always true since I have to reinstall Windows 7.  Once that I have reinstall the printer do I need to re-register it?

  Thank you.

  Yay for me!

• Remote connection between family windows 7 laptop and vista desktop premium office... it's possible... Thanks in advance

  Can I do it? and how safely if possible... is this possible without charge?

  Hello

  You can connect to the laptop Windows 7 to Windows Vista Home premium desktop using remote desktop, even it's free service, I suggest you go through the following links for more information.

  Connect to another computer using Remote Desktop connection.

  http://Windows.Microsoft.com/en-us/Windows7/connect-to-another-computer-using-Remote-Desktop-connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/connect-to-another-computer-using-Remote-Desktop-connection

  Remote Desktop connection: frequently asked questions.

  http://Windows.Microsoft.com/en-us/Windows7/Remote-Desktop-connection-frequently-asked-questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/Remote-Desktop-connection-frequently-asked-questions

• Connection between servers and opening default home

  Question about cross-server logon, if a customer has changed their rules of routing so that the default value at the opening of "wishes" is no longer used and a different call handler is used instead, will be this connection between breaking servers? Looks like that connection between servers using backdoor functionality (# and some numbers) which works with the 'Opening of wishes' system, I understand this right?

  No, it is not hardcoded to opening greeting Manager of appeal, but he needs to finish a greeting (whether for a Subscriber or call handler) - the logic is handled in the PHGreeting conversation (the guy that is used for the treatment of the call manager/subscriber wishes) - so if you have a routing rule that say, load the sign the Subscriber in conversation, then you're going to break.

  But as long as the call is handled by _some_ greeting, the hand of logic should work because the conversation PHGreeting is looking for a specific series of TTS to indicate that it is a grip of calls.

• Connection between the laptop and desktop computer

  Hi I have a Tecra 8000 Windows xp pro, is it possible that I can connect the mobile to my PC, which runs on windows xp family, that is the reason for the transfer of material, from one to the other, is there a likely with different windows problem! I have a dvd drive on the laptop, but not on the PC! someone help please.
  cordially aga151

  You need a crossover cable. This cable is designed for a direct connection between two units. The cable is cheap and you can find it in every store in PC.

• Connection between PC and Photo Frame WiFi digital Journe Air 1000

  Hello
  I'm trying to use the wifi feature to transfer files between my computer and the Journe Air 1000. The manual is useless and there is no option in the image menu.
  I connect to my router broadband flawless and can read RSS, listen to the radio on the internet etc. The image does not appear in my network (Windows XP SP3) locations.
  Can someone help me?
  Thanx

  Hello

  In the manual, I found this:

  + Services + compatible WiFi using
  + 1. After turning on the unit, press or press the button (see manual for signs of button) on the remote control to switch to WiFi mode. +
  + 2. Press the arrow up / arrow down button on the remote control to select a service you want to use and then press OK or press OK on the remote control or. +
  + 3. Shows a message asking to connect to an access point. Confirm the task, then a list of WiFi stations available.
  + appears on the screen. Select a station and press OK or press OK on the remote control to start the connection. +

  I also find that this device supports IEEE 802.11 b/g connectivity with WPA/WPA2-PSK encryption.
  If you must make sure that your router Cela would support too!

  But to be honest that I put t think you might transfer the files using the WiFi network.
  The chassis accepts RSS, Flickr, Picassa, and Radio services.
  I did, t find any info about the file transfer via a WLAN.

• Bluetooth connection between iPhone and iPad

  My iPhone 6 does not connect to my iPad via bluetooth.

  I previously used the bluetooth connection between my iphone and iPad to connect the iPad to the internet. Despite the two devices were among the recognized bluetooth devices and they were previously linked/partner, it was not possible to establish a connection.

  Perform the actions recommended for repair/reissue apple support - 1. Toggle bluetooth, 2. turn on/off the unit, 3. remove the iPhone/iPad bluetooth connections - 4. Reset network settings - 5. Reset all the settings-, nothing works.

  IPhone/iPad devices isn't even on the list of bluetooth devices available on the iPhone, or iPad. Everything that happens is the animated icon turns all the time.

  Deleting a connection to a device and bluetooth speaker/amp from the pairing of the speaker/amp system process made a new connection.

  iPhone 6:

  Model: MG4F2QN/A

  SN: C31NLG8KG5MR

  Version: 9.2 (13 c 75)

  iPad:

  Model: ME898LL/A

  SN: DLXM42LHFK13

  Version: 9.2 (13 c 75)

  Please give instructions for the previous maintenance work bluetooth connection between iPhone and iPad.

  Thanks in advance

  To use the Hotspot feature (that you described for the connection), you must use the instructions below.

  Share your Internet connection with Personal Hotspot - Apple Support

• Localhost UDP connection between FCR and Matlab

  Hi all

  I have a question about the connection between Matlab and FCR UDP. My idea is to Exchange data between Matlab and Labview on the same computer.

  So I found the 'UDP Simple' of the FCR 2.0 sample project where periodically a datasample is generated randomly and sent to the remoteport 61557 local host. In the project a 'fractional number of string for transmission' is used for the transmission of data. The receiver of the sample project reads from the same port to receive the datasample.

  Now, I'm interested to read this simple stream from Matlab (just at first), however, it does not work and I'm not sure why. What I do in Matlab is the following (code Matlab)

  delete variables;
  u = udp ('127.0.0.1', 61557); % Of installation UDP Object
  fopen (u); open reading port %
  A = fread (u, 1);  % read an element
  fclose (u);

  With this code, however, I get a timeout by saying: "' WARNING: unsuccessful reading: the amount of data specified has not been returned within the time limit." "

  I'm not sure why this happens, maybe you could help me out here? I guess that the formet serving to VCF is not the same as in Matlab? Maybe the Terminators are not the same?

  See you soon,.

  Steve0

  Hey

  So, regarding the problem actually, I found the solution today. It was not the firewall, but a simple configuration in Matlab seting the UDP port. So the side of Matlab, to change the definition of udp object according to

  u = udp ('127.0.0.1', 'Thelocalport', 61557);

  If you have

  u = udp ('127.0.0.1', 'Thelocalport', 61557);
  fopen (u);

  A = fread (u)

  fclose (u);
  Delete (u);

  Who does the trick and you can read from the port. Then of course you say Matlab that you read from the "LocalPort" x, which I wasn't aware of.

  On the transmitter side, you simply:

  u = udp ('127.0.0.1', 61557);

  fopen (u);

  fwrite (u, '1');

  fclose (u);
  Delete (u);

  Here, you set just the port of transmiting.

  About the format of the data: I used the simple UDP protocol streaming Comms project where a random number is generated as a double, transformed into a string (ASCII values) and transmitted. At the level of the receiver, you get as much the UDP packet with the ASCII values that you must turn if you want to find the number.

  I hope this helps anyone having the same problem.

  See you soon

• Officeject Pro 8610: Wireless connection between IMAC and Officejet Pro 8610

  I've had this printer for about 6 months now and was hoping a firmware update would happen to solve the problem but didn't.

  I use the printer wireless for all my devices in the House. My Windows devices connect you to the printer very well and print correctly. But for my main computer, which is a 27 inch iMac running El Capitan 10.11.5, I have to "trick" the printer to print from the iMac. It will not keep a session open between the two wireless.

  To use the printer, I keep a blank sheet of paper on the scanner and then reach over and hit "Copy", which then copies the blank paper. During the copy process, I then print everything that I need to print my iMac and it works fine, but 20 seconds after that work is done, the connection is lost between the printer and the iMac.

  I see a lot of questions about it on the HP Support forums, but no one come up with a Solution from HP. Hard to believe knowing that the company that I work uses HP to support the business and buy huge amounts of material of can solve this problem bit between a printer at home and an iMac.

  Would love to hear that a solution is near, or perhaps you must meet your hardware sales that this printer is not compatible with Mac OS. Would have saved me some money and frustration by buying do not.

  Hello

  The printer is fully compatible with Mac OS X, it is more probably relies yoru router or configuration.

  Uses of the devices Apple Hello to communicate with the printer, these require your router to support such a.

  Some routers do not support such an and some may need to be configured properly for such.

  I order to underestand better capabilities of your router, which is model and yoru router barnd?

  In the meantime go to System Preferences > printers & scanners and click the sign more.

  Click the IP tab, and then select the HP Jetdirect Socket Protocol.

  Type the IP address of the printer in the address bar and click Add.

  Note: you can find the IP address by typing on the Ethernet icon or wireless on the front panel of the printer.

  You can print using the newly created queue?

• My connection between my PC and the Internet.

  MY CONNECTION BETWEEN MY PC AND THE INTERNET.

  I sent a message yesterday - don't know if I got a response.

  My question is that something is wrong with my internet connection.  He died in line every 4-10 minutes of use.  I bought a new computer because my technician told me that I had a bad virus on my PC.  But now I have a new PC but my problem remains.

  Can what tests I do to see if the problem is with my wireless router, the Arris modem provided by Comcast, or something else.

  Please help me.

  Dave Fox

  my main email is , but I think I have the address of e-mail as .  so when you meet me you you the man or the other.

  But please reply to this email.

  You have the same problem if you connect directly to your router?

• is it possible to establish a direct connection between two computers, one running on windows xp sp2 and other running on windows xp sp3?

  Hello
  I connected two computers, one running on windows xp sp2 and others running on windows xp sp3 via com using RS232 port via link Modem DFM-562E ++.
  I am able to dial numbers from a PC successfully.
  But when I do a direct link between them (one as a host, the other guest) through the com port, I get error 777.
  Is this because the two PC's using different service packs?
  Help, please.
  Thank you & best regards
  Ravi

  It is not the service pack - although you should have installed sp3 now.

  Your message is not clear: have you been able to connect successfully computers using your modem D-Link?  How did you do that?  Will there be a modem in the second computer?

  What cable are you using to establish a direct connection between the com ports on both computers?  If you have purchased this cable online, please provide a link to the site where you bought it.

  Please describe the physical connection between the two computers.  For example, this is how you connect to the Internet by dial-up services:

  computer 1-{(9 broches) RS-232 serial port}-{RS-232 cable supplied with the modem}-{modem}-{phone cord (RJ-11 modular plugs at each end)}-{telephone wall jack}