Control strategy - access corresponding traffic rule

Similar Questions

• NAT VPN tunnel and still access Internet traffic

  Hello

  Thank you in advance for any help you can provide.

  I have a server with the IP 192.168.1.9 that needs to access a subnet remote from 192.168.50.0/24, through the Internet.  However, before the server can access the remote subnet, the server IP must be NAT'ed to 10.1.0.1 because the VPN gateway remote (which is not under my control) allows access to other customers who have the same subnet address that we do on our local network.

  We have a 2801 Cisco (running c2801-advsecurityk9 - mz.124 - 15.T9.bin) set up to make the NAT.  It is the only gateway on our network.

  I have configured the Cisco 2801 with the following statements of NAT and the relevant access lists:

  access-list 106 allow host ip 192.168.1.9 192.168.50.0 0.0.0.255

  NAT extended IP access list
  refuse the host ip 192.168.1.9 192.168.50.0 0.0.0.255
  deny ip 192.168.1.0 0.0.0.255 192.168.3.0 0.0.0.255
  ip permit 192.168.1.0 0.0.0.255 any

  route allowed ISP 10 map
  corresponds to the IP NAT

  IP nat EMDVPN 10.1.0.1 pool 10.1.0.1 netmask 255.255.255.0
  IP nat inside source list 106 pool EMDVPN
  IP nat inside source map route ISP interface FastEthernet0/1 overload

  When the server (192.168.1.9) attempts to ping on the subnet of 192.168.50.0/24 devices, the VPN tunnel is established successfully.  However, after that, the server is no longer able to access the Internet because the NAT translation for 192.168.1.9 has changed since the external IP address of the router (FastEthernet0/1) at 10.1.0.1.

  The documentation I've seen on the site of Cisco says that this type of Setup allows only host subnet communication.  Internet access is not possible.  However, maybe I missed something, or one of you experts can help me.  Is it possible to configure the NAT router traffic destined to the VPN tunnel and still access the Internet by using the dynamic NAT on FastEthernet0/1?

  Once again, thank you for any help you can give.

  Alex

  Hello

  Rather than use a pool for NAT

  192.168.1.9 - 10.1.0.1 > 192.168.50.x

  ACL 102 permit ip 192.168.1.9 host 192.168.50.0 0.0.0.255

  RM-STATIC-NAT route map permit 10
  corresponds to the IP 102

  IP nat inside source static 192.168.1.9 10.1.0.1 card expandable RM-STATIC-NAT route

  ACL 101 deny host ip 192.168.1.9 192.168.50.0 0.0.0.255
  ACL 101 by ip 192.168.1.0 0.0.0.255 any
  overload of IP nat inside source list 101 interface FastEthernet0/1

  VPN access list will use the source as 10.1.0.1... *.

  Let me know if it works.

  Concerning

  M

• Error "could not open the access control editor, access is denied" while accessing the C: drive

  Hello

  I use Home Basic to Windows 7, I saw two drive C: / and R. /. by mistake I changed security optional properties of the discs now I can

  to access only a: .my c: drive / drive does not open when I open drive c properties, then on security and it continue display "cannot open the access control editor, access is denied.any another application do not open I can not even able to restore it, please help step by step"

  thanx

  Original title: in the c drive security permissions

  Hi Ravindra,

  Thanks for posting your question on the Forum of the Microsoft community.

  Permissions are rules associated with objects on a computer or network, such as files and folders. Permissions determine whether you can access an object and what you can do with him. For example, you might have access to a document in a shared folder on a network. Also, refer to:

  What to know before applying permissions to a file or folder

  According to your error message. I would like you try these steps and check if the problem persists.

  Steps for the reader:
   
  a. click on the drive, click Propertiesand then click the Security tab.
  b. click Advancedand then click the owner tab.
  c. click change, and then do one of the following:
  (d) to change the owner to a user or group that is not listed, click other users and groups and enter the object name to select (examples), type the name of the user or group and then click OK.
  e. to change the owner to a user or a group is listed in the change of ownership of the area, click the new owner.
  f. If you want to take ownership of the contents of the disc, select the Replace owner of subcontainers and objects of the box.
  g. click OKand then click Yes when you receive the following message appears: you are not allowed to read the contents of directory folder name. Do you want to replace the the directory permissions with permissions granting you full control?
  h. all permissions will be replaced if you click Yes.
  i. click OK.

  Check if the problem persists.

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• Mission Control only accesses the desktop. What happened to the rest?

  Mission Control only accesses the desktop. What happened to the rest?

  What happened to the others?  What you are looking for that you do not find?  If you want to help, give us more to go than that!

• Parental Controls + Internet Access Policy 'Add' is shaded on

  I need to add several new devices to my "target devices" in the Parental control-Internet access policy and program schedules that devices can get online. But my 'Add' is shaded out and I'm not allowed to add devices. I use the browser to log in to the router.

  To manage access to the Internet, you have two methods available, Parental control and Internet access policy. That a method can be used at a time. So my first question which option you are trying to use to block or plan the Internet access?

  As the Parental controls can restrict internet access for up to five computers or devices. You can block access to the internet or to limit it to specific times, and you can also block specific Web sites.

  So if you have several devices then 5 to add then you should use the political Internet access option.

• Console Bus service 12 c - cannot display/change access control strategy

  Using Weblogic 12.1.3 + FMW 12.1.3

  So I exported / imported all our existing material FMW GR 11, 1 objects in a new field of 12 c FMW.   Everything works - except that I can't click on the link for "transportation access control.  Contextual text says "connected to the role is not allowed to display/change access control strategies.

  In EM, the Application role 'MiddlewareAdministrators' shows the administrators as a member group.    Proxies that 11 g used the default "of the Everyone group" fail like proxies that can visit based on roles.

  Even if I create a new proxy, I'm stuck using the access of Transport control link.

  

  So I added the permission to my account, and the Transport link is available.  So I removed this policy and then added the authorization for the role of MiddlewareAdministrators, and it works

  Looks like I click on the 'OK' button the first time.

  But this seems to indicate a lack of permissions when fmw 12.1.3 is installed directly.  Since we are upgraded to 11g, I don't know if this authorization is also absent in 12.1.1 and 12.1.2

  I have

• No remote access VPN traffic of Asa

  Hi all

  I set up a Vpn on ASA5510 remote access.

  When the client connect, receive the ip address of the pool (192.168.55.X) but generates no traffic.

  If I type ipconfig on the pc I have only IP and mask but no gateway is not assigned, is this normal?

  If I ping a host of pc to all hosts on the local network 192.168.0.X in the logs I have:

  "3 14 July 2012 16:15:50 305005 192.168.0.10 no group translation found for icmp src FASTWEB:192.168.55.1 dst (type 8, code 0) LAN:192.168.0.10 '

  NAT could be a problem but I do not understand how to do it.

  That's my piece of config:

  standard access list test_splitTunnelAcl allow Net_R_Dmz 255.255.255.224

  standard access list test_splitTunnelAcl allow Net_R_Server 255.255.255.0

  standard access list test_splitTunnelAcl allow Net_R_Client 255.255.255.0

  standard access list test_splitTunnelAcl allow Net_V_VoIP 255.255.255.0

  standard access list test_splitTunnelAcl allow Net_V_Lan 255.255.255.0

  test_splitTunnelAcl list standard access allowed 192.168.0.0 255.255.255.0

  permit access ip 192.168.0.0 scope list Lan_nat0_outbound 255.255.255.0 Net_R 255.255.255.0

  permit access ip 192.168.0.0 scope list Lan_nat0_outbound 255.255.255.0 Network_V object-group

  permit access ip 192.168.0.0 scope list Lan_nat0_outbound 255.255.255.0 Net_R_Client 255.255.255.0

  permit access ip 192.168.0.0 scope list Lan_nat0_outbound 255.255.255.0 Net_R_Server 255.255.255.0

  permit access ip 192.168.0.0 scope list Lan_nat0_outbound 255.255.255.0 Net_R_Dmz 255.255.255.224

  Lan_nat0_outbound ip Net_VpnClient 255.255.255.0 allowed extended access list all

  Fastweb_access_in ip Net_R_Client 255.255.255.0 allowed extended access list all

  Fastweb_access_in ip Net_R_Server 255.255.255.0 allowed extended access list all

  Fastweb_access_in ip Net_R 255.255.255.0 allowed extended access list all

  Fastweb_access_in ip Net_VpnClient 255.255.255.240 allowed extended access list all

  permit access ip 192.168.0.0 scope list Lan_access_in 255.255.255.0 any

  mask 192.168.55.1 - 192.168.55.10 255.255.255.240 IP local pool Vpn_Pool

  Global (FASTWEB) 1 interface

  NAT (LAN) 0-list of access Lan_nat0_outbound

  NAT (LAN) 1 192.168.0.0 255.255.255.0

  Access-group Fastweb_access_in in interface FASTWEB

  Lan_access_in access to the LAN interface group

  Route FASTWEB 0.0.0.0 0.0.0.0 93.x.x.x 1

  internal group R10M strategy

  attributes of R10M group policy

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list test_splitTunnelAcl

  tunnel-group R10M type remote access

  attributes global-tunnel-group R10M

  address pool Vpn_Pool

  Group Policy - by default-R10M

  IPSec-attributes tunnel-group R10M

  pre-shared-key *.

  Thank you.

  M.

  Hi Marco,.

  see this:

  Phase: 7

  Type: NAT

  Subtype:

  Result: ALLOW

  Config:

  NAT (LAN) 1 192.168.0.0 255.255.255.0

  LAN ip 192.168.0.0 match FASTWEB 255.255.255.0 any

  dynamic translation of hen 1 (93.x.x.x.x [Interface PAT])

  translate_hits = 267145, untranslate_hits = 18832

  Additional information:

  Definition of dynamic 192.168.0.10/0 to 93.x.x.x.x/18070 using subnet mask 255.255.255.255

  do not hit the exemption from the rule,

  Please add this to your nat 0 access-list:

  Lan_nat0_outbound line 1 scope ip allow any 192.168.55.0 255.255.255.0

  and let me know how it goes.

  Good luck.

  Mohammad.

• Control to monitor the traffic of serial bus

  Just started my hands dirty with an eval of Veristand.  My tinkering goes well, but I noticed a problem potential for when I started developing my own stuff for my program.  I hope someone can point me in the right direction.

  If things I understand correctly, the data is passed between the target and the host form DBL scalar.  If the user changes a Boolean value true, then the host transmits a 1.0000 to the target, etc.  I will need to implement a set of unique proprietary for the CAN and Ethernet protocols in a device to measure.  For elements such as the 'Régime' or 'State of the switch' it won't be a problem.  However, this Protocol includes the ability to transmit several error codes, with their time stamp and count.  In addition, the customer usually wants to control traffic bus as well.

  I don't see how I can transfer cluster (or cluster table) data to the target for the transmission or the length data message to the host for display variable.  Anyone raised this issue yet?  All elegant ways to do other than to define channels for each possible byte of data that could be received?

  Hi Dan,.

  Shared variables will work, just to manage the deployment of a LabVIEW project, then you can control with the Manager of distributed systems. You can write on it using a device that is customized by using the palette of the shared Variable or create target RT in the custom device project and work with them.

  Another option is to use a component of engine: you can configure engine components in the environment for a setup file settings dialog. A motor component is launched automatically whenever we connect to the target of RT. He didn't need to be called from the Tools menu.

  A part of the engine doesn't have to have a special connector pane or anything like that. It can be any VI. The only special feature that there is the ability to offer synchronization options when executing the workspace. The workspace can be configured to have the following options in the synchronization with the engine components:

  None: Starts the engine component but do not expect it to do anything
  Waiting for synchronization: wait until the motor component to draw a Boolean notifier before and opening of the workspace. This reference of Boolean notifier must come from a Panel control before called engine synchronization.
  Wait full: wait for part VI engine to complete its performance before and opening of the workspace.

  We do not ship a model of engine with VS2009 components. It is located in the: component \NI VeriStand\Engine...

• How to set up parental controls for access on a user account?

  How can I set up a parental block on user accounts

  Go to: Control Panel, Internet Options, content tab, Access Manager, Enable.

  Check all the tabs and choose your preferred settings.

• Repair Windows scam - cannot control panel access control or workstation "Windows Explorer has encountered a problem and needs to close."

  Original title: repair Windows scam - Can can't Access Control Panel or workstation

  My system has been recently infected with "Windows" repair"virus. I managed to delete using Super Anti-Spyware, but all my desktop shortcuts are gone (hidden) so I downloaded "Unhide.exe" and get all my shortcuts. Most of them seems to be working as before, but there are a few, such as 'My Computer', ' Panel, "My Documents", or even "Windows Explorer", which I can't access.» When I try to open them, I get this popup box saying "Windows Explorer has encountered a problem and needs to close" how much he out me of my office of kicks.

  Any suggestions?

  Thank you!

  Brian

  The best way to solve this maybe just create a new user account, transfer your personal data to this account, and then delete the old account. Make sure that you perform the system restore after you did the new account and everything works fine. To purge the system restore, simply disable it then again. Be aware that the creation of a new user account is not the means to get rid of malware. But it is perhaps the best way to get rid of some of the after effects. However, I recommend you scan with Malwarebytes before running these instructions. After scanning you may not create the new account.

  In addition, Jose is correct. Good number of new forms of malware prevent the start in safe mode. Trying to force booting in SafeMode with msconfig, you end up with a boot loop.

• Black screen, no control panel access / MS programs

  Black screen, no access to Control Panel / programs from Ms.

  In addition, menu Dell works and allows access but don't have MS page with links to the programs.

  Help, please.

  Tom

  Hi Tom,

  1. have you made any hardware changes or software on the computer before this problem?

  2. you receive an error message when you try to access the Microsoft applications / Panel?

  You can follow this link and check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  Hope the helps of information.
  Please post back and we do know.

• Icon missing in Control Panel Accessibility Options

  I needed to change a setting in the Accessibility Options, but found that the icon is missing from Control Panel. I found the file access.cpl in C:\Windows\ServicePackFiles\i386 folder. How to restore the icon in Control Panel? Thank you!

  Copy the CPL file to the C:\Windows\System32 folder. Ramesh Srinivasan, Microsoft MVP [Windows Desktop Experience]

• Can I change the password for the parental control for access control to another administrator?

  Related to: Family Safety: frequently asked Questions

  I want to change the password on my FamSaftey account to someone else.  So I do not have access to accept or refuse a site, but someone else.  I created the account on my Microsoft account.  Is it possible for me to give up control of FS to someone else. I know that I can add them, but I can hold it?

  Hello

  Thanks for posting your query on the Microsoft Communities,

  I understand that you want to remove the account Parent you are watching and another Member of the family to monitor the account value.

  I want to let you know that you can not replace the primary parent in family safety. First, add a family another parent counts on the safety of the family and then delete your account.

  You can follow this thread for more information:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_other-security/changeremove-primary-parent/fd0bead6-3db5-473a-9954-76fc66898011

  I hope this helps. If you have any other questions, we will be happy to help you.

• How to disable control panel access to other users

  I would like to set up a Windows 7 Pro machine so that the administrator or the Administrators group can access the control panel and disable other users to access.  So far, I can use GP to disable all access or allow access for ALL, but not to be selective in who I grant access.

  Thank you.  These items were not what I was looking for.

  That's what I needed.

  http://www.SevenForums.com/tutorials/101869-local-group-policies-apply-all-users-except-administrators.html

• Error properties of type of voice product control panel access

  Hello

  I just finished the installation and migration to Windows 7 from Windows XP.

  When I access the control panel I get the following:

  Properties of type of voice error: unable to load resources in national language

  There is virtually nothing on the Internet. All I know is that there was a post

  German and Chinese back in the 1990s and Windows 95/98.

  I had a version of ViaVoice how IBM back at this time. Something

  may have survived the original upgrade of XP, but did not appear until the

  recent migration to Windows 7. Is there a conflict with speech recognition in Windows 7

  or was it a long and ignored, but invisible, problem?

  Thank you

  This is due to a current registry for this program from IBM. Try to remove in the register, it worked for me. Check with the Administrator IBM team to remove it to your computer.

  Check that ink as well, it has the same error:

  https://blog.mediaRAIN.com/2009/08/Flex-loading-remote-modules-throws-the-following-error-unable-to-load-resource-module-from/

  Astalavista.