Conversion failed... Solution, anyone?

Similar Questions

• Catalog items 14 (from PSE 3) conversion failed

  I was unable to properly convert my PSE3 catalog to PSE14.  I went through all the possible solutions in the knowledge base, and I still cannot get lucky.

  My PSE3 catalog resides on a windows XP computer and I try to move it on a 64-bit Windows 10 with PSE 14 computer.  With my last attempt, I followed the instructions in the article titled "convert organiser for 64-bit versions catalogs / Photoshop Elements 13 or later.

  I saved the PSE3 catalog to a hard drive.  I restored the PSE 14 catalogue.  It seems to work fine until the failure of the conversion notice.

  I used the catalog Conversion utility to convert the catalog to a catalogue of .pse13db.  He also appeared to work properly.

  During the conversion of a catalogue of PSE14, he went to 37% complete and continuous fast conversion for awhile without the % (he continued to display the names of files that have been conversion) back, and then I got the standard error message.  I checked the log by following the instructions, and that's what it contained:

  Conversion log: began the conversion of D:/media/photos to C:/ProgramData/Adobe/Elements Organizer/catalogs/photos

  copy the entire catalog directory...

  error: D:/media/photo copy failed, abandonment

  catalog copy failed

  Conversion log: Conversion failed

  It is the newspaper.  I do not know how to do this, because I think I tried everything in the KB and that I could find in the forums.

  You have followed the instructions:

  Convert catalogues organiser for 64-bit versions. Photoshop Elements 13 or later version

  Have you downloaded the PSE13 version as requires it?

  7. at the end of the conversion process, the .pse13db file and the cache of miniatures are available in the specified destination folder.

  8 launch organizing elements, choose file > manage catalogs > choose location custom, and then click file > manage catalogs > repair/Optimize.

  Note:

  If the conversion fails, open your catalog of the version of the elements organizer that it was created in, and then click file > manage catalogs > repair/Optimize.

  If you have installed the trial version 13, you can check the catalogue with the "catalog.pse13db" file is working, and you can use it to repair/Optimize before using version 14 of the convert.

• The conversion failed 13-14 PES PES catalog

  I can't convert Photoshop elements Photoshop elements 14 13 catalogues.  the last entry of PSE-conversion-log is: an error occurred in the SQLite database: cannot open database file.  The conversion failed.

  I was finally able to convert my 13 catalogues PES to PES 14.  I don't know what action solved my problem but I changed a number of things.  First of all, I had installed 14 first PES at the same time as the installation of 14 pse above all catalogues have been loaded but had not opened first.  I opened the first with the catalog that I had managed to convert previously.  I left the first and rebooted my computer.  Secondly, I opened the pse 14 Organizer and deselected the option of automatic facial recognition in preferences > media analysis.  Catalogue conversion completed successfully this time.

  Thank you for your help.  I think that my problem is now solved.

• Hyper-v for vsphere conversion fails

  Hey guys,.

  I try to migrate a virtual machine from a hyper-v on a server for vsphere server. Therefore, I use vmware converter 5.0 standalone.

  The conversion fails at 1%.

  The only error I see is: "danglisng ssl error.

  Then, I have attached the log files... Maybe you can help me and find out what is blocking the conversion process.

  It's the same error as before:

  2012-07-10T16:25:31.416+02:00 [02980 info 'task-1'] GetManagedDiskName: Get disklib file name as vpxa-nfcssl://[nfs_esx_jako_001] W2K8R2AXDEV02/[email protected]:902!52 ca d1 16 89 ab 07 1c-80 22 6e 2e d1 85 d0 bb
  2012-07-10T16:25:52.461+02:00 [02980 warning 'Default'] [,0] [NFC ERROR] NfcNewAuthdConnectionEx: Failed to connect to peer. Error: Failed to connect to server haba-vmware-11.haba.int:902
  2012-07-10T16:25:52.461+02:00 [02980 error 'task-1'] Failed to open source disk 'vpxa-nfcssl://[nfs_esx_jako_001] W2K8R2AXDEV02/[email protected]:902!52 ca d1 16 89 ab 07 1c-80 22 6e 2e d1 85 d0 bb' with error 'NBD_ERR_NETWORK_CONNECT' (error code:2338)
  2012-07-10T16:25:52.461+02:00 [02980 error 'task-1'] hosted to managed disk clone failed: Unable to open destination disk
  2012-07-10T16:25:52.476+02:00 [02980 error 'task-1'] Disk clone failed with clone error Unable to open destination disk
  

  The first line in the newspaper is at 16:25:31 and shild line is 16:25:52 - it is about 20 seconds later, which makes me think that this is a problem new network - not able to connect to hyper-v host haba-vmware - 11.haba.int on port 902 source within a certain period of waiting.

• get the conversion failed on the export of PDF files.

  get the conversion failed on the export of PDF files.

  Hi jfcobb999,

  I'm sorry that you are having problems, file conversion. You convert the web interface, or through Adobe Reader? You have a large number of files in the folder root of your list of files on Acrobat.com?

  Try to start these things:

  • Empty the cache of the browser, and then try again.
  • Use another browser.
  • Make sure the drive is up-to-date by selecting help > check for updates.
  • If you have a large number of files on Acrobat.com, some of them move in a subfolder.

  Please let us know how it goes.

  Best,

  Sara

• Problems of conversion of PDF to MS Word document.  I managed to convert 4 files and now the subsequent files generate a "Conversion failed" error when you try to convert the file.  I have a big manuscript and I separated each chapter to assist with co

  Problems of conversion of PDF to MS Word document.  I managed to convert 4 files and now the subsequent files generate a "Conversion failed" error when you try to convert the file.  I have a big manuscript and I separated each chapter to help the conversion; as I said, the first 4 pieces without problem, then the conversion failure.  I tried to convert the document integer and same result.  Specifically, I bought the feature export to Word.  Please help.  I had initially export the Word Perfect PDF document and attempting to pass PDF to MS Word.

  Hi sdr2014,

  I'm sorry to hear that your conversion process is at a standstill. It seems that the problem is not specific to a single file, you have been unable to convert anything, since the first four chapters of a correct conversion.

  So, let's try this:

  If you want to convert via the ExportPDF site, please sign out, clear the browser cache, and then reconnect. If you use the drive, please choose Help > updates to ensure that you have installed the latest version.

  Please let us know how it goes.

  Best,

  Sara

• ORA-31061 XDB-error: special tank tank escaped conversion failed

  I build a script to export data in a table to an xml file. After that, I came across this error: ORA-31061 XDB-error: special tank tank escaped conversion failed.
  
  I have reduced the problem in 1 column and now knows that this query will trigger the problem:
  
  Customer OF SELECT XMLELEMENT ('name', lastname)
  
  clearly, there are some lastname in the array that contains some sort of bad character. The table contains 24,000,000 customers.
  Is it possible to know what record (or records) are the cause of the problem?
  
  Version information:
  
  Oracle Database 11 g Enterprise Edition Release 11.2.0.2.0 - 64 bit Production
  PL/SQL Release 11.2.0.2.0 - Production
  CORE Production 11.2.0.2.0
  AMT for 64-bit Windows: Version 11.2.0.2.0 - Production
  NLSRTL Version 11.2.0.2.0 - Production

  Erik_NL wrote:
  WE8MSWIN1252

  Oracle recommends to use Unicode (AL32UTF8) as the database character set. Anyway, I'm still not sure that the problem is necessarily tied to the character set. So, as you suggest, it might be useful to have the list of family names is generating the error.

  You can try something similar to the following:

  CREATE OR REPLACE TYPE names_ty IS TABLE OF VARCHAR2(50)
  /
  
  CREATE TABLE bad_names(lastname VARCHAR2(50) NOT NULL);
  
  CREATE OR REPLACE PROCEDURE logBadName(p_name VARCHAR2)
  AUTHID CURRENT_USER
  IS
      PRAGMA AUTONOMOUS_TRANSACTION;
  BEGIN
      INSERT INTO bad_names(lastname) VALUES(p_name);
      COMMIT;
  END logBadName;
  /
  SHOW ERRORS;
  
  DECLARE
      customersNames   names_ty := names_ty();
  
      BAD_NAME_EXCEPTION EXCEPTION;
      PRAGMA EXCEPTION_INIT(BAD_NAME_EXCEPTION, -31061);
  
      xmlInfo     XMLTYPE;
      idx         PLS_INTEGER;
      lastName    VARCHAR2(50);
  BEGIN
      SELECT lastname
      BULK COLLECT INTO customersNames
      FROM customer;
  
      idx := customersNames.FIRST;
      WHILE idx IS NOT NULL LOOP
  
          lastName := customersNames(idx);
  
          BEGIN
              SELECT XMLElement("name", lastName)
              INTO xmlInfo
              FROM dual;
  
              EXCEPTION
                  WHEN BAD_NAME_EXCEPTION THEN
                      logBadName(p_name=>lastName);
          END;
  
          idx := customersNames.NEXT(idx);
      END LOOP;
  END;
  /
  

  And finally the rows in the bad_names table will give you the information you're looking for.

  I hope this can help you.

  Kind regards
  Dariyoosh

  Edited by: dariyoosh June 4, 2013 08:32

  Edited by: dariyoosh June 4, 2013 09:47

  Edited by: dariyoosh June 4, 2013 09:48

• Conversion failed Acronis backup of windows 2003 server to EXsI: FAILED: an error occurred during conversion: "an error of file encountered.

  I am trying to convert an image backup acronis tru to a windows 2003 server to a server esxi virtual computer, a system I had converted previously on 4.x and exsi 5.1 Converter and using the same image and same PC to convert, but now he is unable to 59% with the status:

  FAILED: An error occurred during conversion: "a file error has been detected" and error: error: impossible to clone the C:\Windows\TEMP\vmware-temp\vmware-me\nvdsxwvgwgxyklny\disk-1.vmdk drive on the virtual machine "server."

  Don't know where to go with this.

  Anyone have any ideas?

  Unfortunately, there is a mistake in your image file: 2014-05 - 20 T 20: 41:17.034 - 04:00 [02140 WARNING 'Default'] [, 0] [NFC ERROR] read has no curSector = 588398592, nSectors = 512: failure of a custom of third party library function call: (3116).

  Seems like you need to repair the virtual machine somehow, probably you start it, or use a tool acronis to repair the image.

• P2V conversion failed

  Hello, I'm under VMconverter 5.5, I'm trying to convert Windows server 2 K 3 server R2 Enterprise Edition, and I received a failure at 96% (so close). The failure, I got was FAILED: an error occurred during conversion:"converter.fault.FileIOFault". It was the 3rd disk cloning, I wonder if someone can help me understand where the issue is so I can start another conversion again. Attached are the logs.

  Your error is:

  2014-03-16 T 12: 14:40.330 - 04:00 [03164 info "task-2'"] CloneTask updates, State: 1, percentage: 97, xfer rate (bps): 8872757

  2014-03-16 T 12: 15:25.862 - 04:00 [03164 error "task-2' '] BlockLevelVolumeCloneMgr::ReadAndSkipBadBlocks(): error (type: code 2: 2) read of 8192 bytes from 0x000000b2523d1000 of the volume source G:

  2014-03-16 T 12: 15:25.862 - 04:00 [03164 error "task-2' '] BlockLevelVolumeCloneMgr::ReadAndSkipBadBlocks(): fatal error (type: code 2: 2) read of 8192 bytes from 0x000000b2523d1000 of the volume source G:

  2014-03-16 T 12: 15:25.878 - 04:00 [03164 error "task-2'"] BlockLevelVolumeCloneMgr::CloneVolume: failed with exception converter.fault.FileIOFault

  If you run "chkdsk g:/b" on the source machine and then try again.

  HTH

• Conversion fails with the error: COULD not: - ERROR - convert: converter.fault.FileCreationFault

  Hello, I try to convert a windows 2003 server of citrix server to vmware (the last of them succesfull 20).

  The job runs up to 95% one error:

  "Create von ' \\.\vstor2-mntapi10-shared-D587D58700001000000000000B000000\$Reconfig nicht possible."

  Logfile by saying:

  2013 04-07 T 14: 14:20.752 + 02:00 [error 12632 'Default'] [task, 350] [LRO] Unexpected Exception: converter.fault.FileCreationFault
  2013 04-07 T 14: 14:20.753 + 02:00 [12632 info 'Default'] [task, 379] [task-72] - ERROR - convert: converter.fault.FileCreationFault
  -> (converter.fault.FileCreationFault) {}
  -> dynamicType = < unset >
  -> faultCause = (vmodl. NULL in MethodFault),
  -> file = "\\.\vstor2-mntapi10-shared-D587D587000010000000000005000000\$Reconfig$"
  -> msg = ""
  ->}
  2013 04-07 T 14: 14:20.753 + 02:00 [12632 info 'Default'] [diagnosticManager, 267] retrieved taskInfo to "converter.task.Task:task - 72" mapping to "converter.task.Task:task - 72".»
  2013 04-07 T 14: 14:20.753 + 02:00 [12632 info 'Default'] [diagnosticManager, 307] the task with id = "task-72" proved to be a task 'recent '.
  2013 04-07 T 14: 14:20.753 + 02:00 [12632 info 'Default'] [diagnosticManager, 321] no existing group of newspaper found to task with id = "task-72. The task is still 'young' so a bundle of newspapers going now is assigned.
  2013 04-07 T 14: 14:20.753 + 02:00 [12632 info 'Default'] [diagnosticManager, 790] recovery job related diagnostic for the tasks of server with id = "task-72.
  2013 04-07 T 14: 14:20.925 + 02:00 [10056 "Default" info] passage work 0 "job-72" completed with an error. -struct Converter::Server:Job:JobExecutor:SchedulerUpdateSpec __thiscall Converter::Server:Conversion: ("d:/build/ob/bora-875114/bora/sysimage/lib/converter/server/conversion/conversionJobExecutorImpl.cpp:405")
  2013 04-07 T 14: 14:21.125 + 02:00 [10056 "Default" info] suspended 1 elements of Planner for employment (job-72) - __thiscall Sub Converter::Server:Job:JobProcessorImpl:SuspendJobAux(const_class_Converter::Server::Job::InternalJob_&,class_Converter::VdbConnection_&) ("d:/build/ob/bora-875114/bora/sysimage/lib/converter/server/job/jobProcessorImpl.cpp:828")
  I run vCenter Converter Standalone 5.01 version 875114
  I tried to erbuild the mbr, the boot sector and the boot.ini, but no success yet a screen is blue with 0x00000007b
  any new idea

  Yes, something is not in communication with the pilot vstor2:

  2013 04-07 T 14: 13:11.545 + 02:00 [info 09908 "Default"] [, 0] Vmount library: 1450 error communication error with the pilot while
  2013 04-07 T 14: 13:11.545 + 02:00 [warning 07680 'Default'] [, 0] error 999 (hive to load error: unknown error 999 (0x3e7) (999)) temporary hive loading

  1450 error is "insufficient system resources exist to complete the requested service."

  999 error is "error performing a paging operation."

  Both are unusual. Try the task set up on destination VM, if the task fails you will need to restart the source machine and try to restart the conversion.

  HTH

  Just found/3 GB switch in your boot.ini file, there are rumors that sometimes you should remove this switch for successful conversion: http://communities.vmware.com/message/1708679#1708679

• RHEL 4 P2V conversion fails at Boot/cloning

  I'm trying to convert a box of RHEL 4.9 of the physical to virtual, and I'm running into the following error message:

  Error: Impossible to clone the volume mounted on ' / boot ' to 'ip.address.of.source '.

  / boot is the first player tries to clone through.

  I joined the server agent and the worker log files.  I am using vCenter Converter Standalone 4.3 (Win7 x 86) and ESXi 4.1.0 and conversion from a distance.

  The only thing I've changed is the NIC, and I assigned an IP address using the virtual machine and set the DNS suffixes.  Drives, memory and processors are that they are on the physical machine.  The server that hosts ESXi has the hardware to support.

  I have the physical ability to su to root.  In the converter - converter - Worker.xml and agent.xml files, I put useSudo and useSourcePasswordInHelperVm to true.  I tried enabling root SSH and conversion of the machine, but I still end up with the above error.

  I checked for if make sure that time is located on the linux machine as the machine virtual host machine (I found a thread indicating that it was someone else).  I also checked the xml files above for keepSparseFile that is set to true by default.

  I tried Googling how to install agent converter on the Linux box itself and execution of the conversion from there, but I guess that an agent has not been yet developed.  I found where someone has started a petition. If there is another way around him, please let me know.  I'm willing to try anything.

  What could help to convert this machine?  I've searched and searched, and every possible solution I tried did not work.  Help, please!

  Good to know it worked

• To combine files, custody conversion fails with red notice that document if the protected password. What does that mean and how do I?

  To combine files, conversion can fail with a red notice that the document is password protected. I combines all pdf files and had to be managed with the same content under a different file name. What is the problem and how can I fix it?

  Hey SUSANOO.

  I'm sorry, but you cannot combine files if they are protected by Word.

  You can check the same slot "file > properties > Security"

  Kind regards

  Ana Maria

• Re: Troubleshooting Captivate 7: MP4 Conversion failed

  Hi all, I am a relatively new user and cannot find a resolution for this error online. I'm trying to publish my project in format SWF and HTML5. The publication fails and says "HTML Publish slide 28 converstion MP4 failed error" How do I fix the error?

  Thanks, I undertand it could be a basic solution...

  Thank you, I've hidden the slide and it published successfully. I then showed the slide again, and he has published. Strange!

  with respect to the FMR file, change is dimmed out in Captivate, if I find the source file, I can only run in the browser.

  Thanks for the help, hide/show did the trick!

• Re-use VMDK for conversion failed

  I am attemping to convert an old box of Windows 2000 white with raid 5 to an HP ML350 G5 with P400/512 MB RAID 1 + 0 VMserver on Windows 2003. It has been supported 27hrs for 86%. I cancelled the task because he was going to take me outside the window, I had to do the migration.

  I had a disk fails in raid 1 array + 0, so which could contribute to some of the slowness, it took nearly 12 hours to create the VMDK initially.

  I wanted to know is a way to re - use the VMDK created during the first attempt?

  Thank you

  No, these VMDK is incomplete and cannot be reused. Also, I think they should have been removed after that you canceled the conversion.

• The DNG CONVERSION FAILED

  When you download the raw files from the Canon 550 d camera. The files can be found under the fingernails of the thumb, until images are entered in the record of the bridge. Once the files in the folder as .cr2 files is more available. I camera raw 6.1 downloaded, but this did not help. The error message I received after the images are downloaded is the conversion of the DNG format failed. How this can be resolved. The operating system is windows 7 pro and I have Photoshop CS5

  I assume that you use the bridge Adobe Photo Downloader to download and convert files to DNG using the bridge, correct?

  Have you installed the plugin 6.1 manually or by using the patcher/Installer?

  Thank you

  David