Copy the Pix on TFTP config

Similar Questions

• Copy startup-config for pix via TFTP

  Where am I missing it? I know it's possible to copy a config pix down via Tftp using the

  WR net tftpIP: filename

  How can I do the reverse copy, the startup-config for the pix using tftp.

  Easy to do with a router or a switch. I don't see any docs on ORC that specify where to copy the startup-config.

  Hello

  Use the Net Config command

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/cmdref/c.htm#wp1055799

  Thank you

  Nadeem

• Unable to retrieve the password on PIX 501 - TFTP failed (return: arg:0 x 0-1)

  In the course of a merger of office, we got a PIX 501. It is obviously been configured but nobody is anywhere knows anything and there is no documentation regarding the config not found. As a result, I tried to retrieve the password so that we can reconfigure and reuse it for our purposes. I followed the instructions on the cisco.com web site but get the error message:

  TFTP failed (return: arg:0 x 0-1)

  I tested the connectivity between the PIX and TFTP server and it works. I can post a txt file that is captured is of no help.

  Any ideas as to what I am doing wrong or, more importantly, how the address so that I can recover the password. Certainly, it is the first time that I have worked on a PIX.

  Thanks in advance for any help.

  Sergio

  Sergio,

  Depends on when you received the pix. I'll try with the code 6.1 and 6.2. Thank you

  Renault

• Comment by instructions in the PIX config file?

  Hello

  Is there a way of declarations of entry comment in a PIX config file? If so, how?

  TIA

  Prefix the line with a: (colon).

  for example. The first line of the following is a comment and is ignored

  : Allow access to the Web server

  acl_outside list access permit tcp any host 1.1.1.1 eq www

  Note: Comment lines are deleted when the configuration file is entered in the PIX.

• Display the PIX ver 6.3 (4) config

  Hi all

  All of a sudden I'm more able to display the configuration file running a PIX 515 v 6.3 (4) in the usual way. In the past, after issuing the command "show execution", the PIX will be stop and ask "- More -" press a key to continue. So either I have to press the space bar to display the next page, press return to display a line and press any letter to quit. Now the show, run the command will simply display the start to the end without stopping. How can I fix and restored to the original setting? Thank you

  Try

  pager lines 24

  http://www.Cisco.com/en/us/docs/security/PIX/pix63/command/reference/Mr.html#wp1026890

  Jon

• Copy the IOS Aironet configuration

  I created a 1041 AP running IOS autonomous. No controller. I have three that I want to copy the configuration of the installation on others. I have the right document, but need someone to help tell me what commands will get my set of AP configuration a FTP'd to my computer and how to copy this configuration back to another model of the same access point. This way I don't have to change a few more settings of the AP instead of starting from scratch.

  Thanks in advance,

  Kirk

  What I am referencing begins under article 20-10

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410b.PDF

  HI Kirk,

  To copy the configuration of AP to PC, you can run the command below. My preference would be to use tftp instead of tftp.

  copy: the execution of the system-configftp://x.x.x.x/ap.txt or copy running-config tftp://x.x.x.x/ap.txt t
  (where x.x.x.x is the ip address of the tftp server and ap.txt is the name of the configuration file)

  Top of page PC of AP copy, you could use command below.

  copy tftp://x.x.x.x/AP.txt startup-config (where x.x.x.x is the ip address of the tftp server and ap.txt is the name of the configuration file)

  Make sure that you are able to ping to the ip address of tftp to the AP before trying the copy procedure.

  Hope that helps.

  Concerning

  Najaf

  Please rate when there is place or useful!

• The upgrade of the PIX firewall

  I currently have two firewalls Pix 515 (v4.4 and v6.2). I want to update the v4.4, but am unable to download the software from Cisco. Whenever I try to download using the link 'download pix software', it times out.

  I have already set up a tftp server and plan on the use of monitor mode to perform the upgrade. I already did a "write net:" to save the current configuration. " In addition, the original configuration remains intact, or they will be lost after the upgrade.

  Thanks in advance.

  Looks like you may have a problem with the download or the browser proxy. Try another host and/or browser and see if it works better.

  Since the PIX 4.4 software and versions later, you can go directly to any newer version of the software. To preserve your config, but it's always a good idea to back it up before an upgrade as you did. The config in the PIX is actually not get converted when PIX is restarted with the new software - what happens the first time you do a "write mem" under the new software, it is so important to remember to do as part of the upgrade process. You can then check the config freshly recorded against your configuration of backup for all differences. In addition, it is important to check the Release Notes before upgrading, but if you have a config PIX relatively simple it will probably be fine. One thing you want to do is migrate away from lines on access lists. Cisco is a utility that allows to convert them for you, and it does a very good job as long as your config is not too complex, so I might suggest to give it a try and see how it works for you. The downloadable version of this utility must be on the same page as other PIX software download, and there are versions for Windows and Sun Solaris.

  Good luck!

• W2000 PPTP in the path through the PIX PIX

  Inside of a configured simple PIX I have a w2000 customer VPN with PPTP. The client cannot talk to one another otside PIX configured with VPDN.

  Everything works as expected if I put in a nat-Firewall NETGEAR801 instead of PIX siple.

  See PIX config and syslog. Waths evil?

  6.2 (2) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate 2KFQnbNIdI.2KYOU encrypted password

  FAXRuw8pF2Tl7oBe encrypted passwd

  HMS host name

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  access-list acl_outside allow icmp a whole

  access-list acl_outside allow accord a

  Allow Access-list acl_outside esp a whole

  pager lines 24

  opening of session

  recording of debug console

  recording of debug trap

  host of logging inside the 194.132.183.10

  interface ethernet0 10baset

  interface ethernet1 10baset

  Outside 1500 MTU

  Within 1500 MTU

  external IP 217.215.220.221 255.255.255.0

  IP address inside 194.132.183.2 255.255.255.192

  alarm action IP verification of information

  alarm action attack IP audit

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Access-group acl_outside in interface outside

  Route outside 0.0.0.0 0.0.0.0 217.215.220.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  No sysopt route dnat

  NSM #.

  Syslog sed:

  % 305011-6-PIX: built a dynamic TCP conversion of ide:194.132.183.10/1366 to outside:217.215.220.221/1124

  % 302013-6-PIX: built 212 for outbound TCP connection: 194.71.189.109/1723 (194.71.189.109/1723) to inside:194.132.183.10/1366 217.215.220.221/1124)

  % 3 PIX-305006: failure of the regular creation of translation for the internal protocol 47 src: 194.132.183.10 outside dst: 194.71.189.109

  % 3 PIX-305006: failure of the regular creation of translation for the internal protocol 47 src: 194.132.183.10 outside dst: 194.71.189.109

  % 3 PIX-305006: failure of the regular creation of translation for the internal protocol 47 src: 194.132.183.10 outside dst: 194.71.189.109

  % 3 PIX-305006: failure of the regular creation of translation for the internal protocol 47 src: 194.132.183.10 outside dst: 194.71.189.109

  % 302014-6-PIX: disassembly of the TCP connection 212 for side:194.71.189.109/1723 to inside:194.132.183.10/1366 duration 0:00:10 TCP fins 788 bytes

  First off I would say don't not cut and paste your config PIX here, or at the x.x.x.x at least on your external IP address.

  The PIX does not support PPTP thru PAT (nat/global). PPTP uses the Protocol IP 47 (GRE), and the PIX cannot PAT these cause there is no TCP/UDP port number to use.

  PIX 6.3 code it will however support, but it won't be available until the beginning of next year. At the moment the only way to circumvent your situation is to define a one-to-one NAT translation for this internal host. Something like:

  > static (inside, outside) 217.215.220.222 194.132.183.10 netmask 255.255.255.255 0 0

  will do for you, providing you 217.215.220.222 routed and available. I would also change

  > acl_outside of access list allow accord a

  TO

  > acl_outside gre 194.71.189.109 allowed access list host 217.215.220.222

  It's a little safer.

• I have remove the IOS of the aironet 1100 series by mistake and now I need to copy the IOS image file

  Hello

  I have a cisco aironet 1100 Series wireless access point.

  by mistake I delete the IOS of the router and now I need to copy the IOS image again on it.

  I need your help please.

  For now, he has the Ethernet led RED, Green State, Rdio RED. T no Cisco IOS image file the spirits).

  I downloaded the file c100-k9w7 - mx.123 - 8.jed

  and I download the tftp (tftpd32) servers

  I have the router connected directly to a pc with the static ip address of 10.0.0.2

  but the problem is actually that I don't need the 1100 router ip address right now, I can't access it through a web browser.

  and by a tftpd32 I try but no function.

  I don't know what I'm doing wrong.

  other things, it's that I did not find a clear manual on how to use a tftpd32 to transfer the file to the cisco router 1100 series.

  Thank you.

  I'll wait your hepls.

  Convert a standalone Lightweight Access Point
  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp161272

• Copy the ios from Cisco 1140 AP

  Salvation; I'm working on the Cisco 1140 AP which is loaded with a slight IOS. I need to change the IOS in standalone version. I managed to enter the configuration mode and tried to use tftp to copy the IOS to the camera flash. but the Unit periodically (in fact all the 1 minute) attempted to display the IP by connecting to DHCP. even I assigned static IP address, but after a minute, it changed its method to allocate using DHCP, because it says to get configuration from a controller. TFTP works well, but in the Middle, change IP stop the copy process. How can I copy independent IOS for the flash on the camera?

  In my view, increasing the IP address getting timer will leave me to start and complete the process of copy from the TFTP server. But how can I do this? is there a solution to stop the device to periodically change its IP address? TNX.

  Here are a few links that explain the conversion:

  By using a TFTP server to revert to a previous version

• Ping on the PIX firewall

  Is it possible to ping directly from low security high security without translations on a PIX?

  For example, 192.168.2.90 is currently natted to 10.0.0.4 by the pix. I want to ping directly from 192.168.2.4 to 10.0.0.4.

  I can certainly ping directly from 10.0.0.4 to 192.168.2.4.

  Please let me know if you would like to see the complete config.

  I hope I understand your question completely. You try to ping from one interface to another on your PIX. This URL explains how this can be done.

  http://www.Cisco.com/warp/public/110/31.html

• Enable syslog server behind the PIX

  Could someone tell me a config that allows a server syslog (Kiwi syslog) to get behind the PIX syslogs. I have a 2K with the KIWI syslog server behind a PIX 501.

  I have the static command, the access group and the access-list:

  public static 192.104.109.92 (Interior, exterior) 192.168.15.200 netmask 255.255.255.255 0 0

  Access-group local_server in external interface

  local_server list access permit udp any host 192.104.109.92 eq syslog

  Man, I can't understand it.

  Thanks for any help

  You could:

  1. make a capture of port syslog traffic directed to the syslog server.

  2 Terminal monitor - deny traffic showed clearly when I had not set up the firewall to forward the traffic. (Note: attention on busy firewall)

  3 netstat - a on the syslog server

  4. If you allow, you should be able to portscan the server on port of syslog by your firewall.

  5. is your syslog capture created file? It is not created if the service never started.

  6 - is the service running in the system context or perhaps another account that doesn't have the correct rights?

  The answers seem to indicate a service not started that seemed likely. What you describe happened to me when I had the demon also version; I went to service version and the problem has been resolved (once I opened the port.)

  I love the kiwi syslog. I use with Snare and BacklogIIS and receive alerts within 60 seconds to my mailbox when something bad happens. It always fools of my end users out when I call them with the problem solved when they seek always my number report the problem.

• The PIX software update

  To upgrade the software on the PIX 515, I just need to publish the following:

  copy the flashftp://172.16.6.100/pix622.bin t

  and then reload?

  Seems too easy.

  What is your current image? If its 5.1 or higher, then you are fine with your orders. If before 5.1, then you still have work to do (because they have no copy command. Need to start monitoring and upgrade mode in this mode). In addition, you are tipping? If so, first make the secondary pix (cables, upgraded, reconnect, disconnect active, upgrade, plug) then the active primary PIX.

  It will be useful.

  Steve

• Incoming direction on the Pix interfaces

  Access-group of statements always apply an ACL to an interface with the command "in the interface. The Pix docs say "this filter incoming packets to the given interface. I would like a clear definition of what's arrival. My understanding, according to the logic of the access lists that I have made a request, this incoming is-bound traffic in the interface of the Pix of the connected subnet. So for the following interfaces, traffic entering the following subnet provenance

  outdoor - traffic from the Internet

  inside - traffic from inside Lan

  DMZ - traffic coming from the DMZ

  I just wanted to check that, because it's contrasted with IOS router configs. My understanding is the following:

  Outside the s0 interface - incoming list applies to incoming traffic from the Internet

  Inside interface e0/0 - incoming list applies to incoming traffic traffic vs subnet towards inteface as in my example of Pix inside.

  If someone could verify this, point me to a link or correct my examples?

  Thank you

  RJ

  1. Yes, to filter incoming traffic in the interface

  2 traffic can originate from anywhere, that is to say of many jumps/subnets away or directly connected before it hits the interface, but it moves to the interface. Same logic on pix and router.

  3. Yes, to filter traffic leaving the interface

  4 Yes, traffic position away from the router to the connected subnet or a destination of many jumps far (PIX has no more outgoing ACL)

  Steve

• Telnet to the PIX from the outside

  I tried the task through several suggestions.

  None of which worked. My last try was using this link.

  http://www.Cisco.com/en/us/customer/products/sw/secursw/ps2120/products_user_guide_chapter09186a0080089bd6.html

  PIX VPN client works fine however I am still unable to telnet to the PIX.

  In addition, the document speaks of configuration on the client.

  Step 3 in the VPN client, create a security policy that specifies the IP address of the remote party identity and IP gateway under the same IP address IP address of the external interface of the PIX firewall. In this example, the IP address of the PIX firewall outside is 168.20.1.5.

  I see there is only one place to put an IP address on the client. There is no place on the client to a gateway address. I tried to change my gateway machine and it still does not work.

  Does anyone have a config to work on how to Telnet to a PIX from the outside?

  The step that you are referencing is for users who use the old client VPN CiscoSecure. Do you really use that? I'm guessing that you are actually using the VPN client 3000, in which case you just have:

  (1) an acl of encryption that allows the traffic of your address has been assigned outside the pix

  (2) a statement of telnet that allows telnet address assigned from outside

  i.e.

  no_nat of ip host 200.1.1.1 access list permit 10.1.1.100

  Telnet 10.1.1.100 255.255.255.255 outside

  HTH

  Jeff