Could not connect more than 4 devices to time capsule

Similar Questions

• iTunes could not connect to the iPhone "iPhone", because an invalid response was received from the device.

  So I am a new iphone 7. I had a 6 before that. Everything was fine until the day where I got the 7, I decided to try a manual on itunes for my 6 backup so that I could put this on the new phone. I use now icloud backup but before that he always did on my computer. Its itunes version 12.2.2.25 as it is the most recent, that I can run with 10.7.5 which is the newest my mac pro can work without hacking it. Again, never had a problem before it save and use it to transfer music. Anyway, I received the message "iTunes could not connect to the iPhone"iPhone"because an invalid response was received from the device." I tried 3 different usb cords. I tried both ports to the front of the computer and all 3 in the back. Abandoned and did a backup icloud. Installed on the new phone. Everything transferred except my music library which is real download of my CD via itunes. If something was wrong on the iphone 6, surely the new phone that starts with a clean slate will be very well... wrong.  Same message. Leaves through ports, cables, etc. Is it just a simple matter of ios 10 now works with my version of itunes?

  A new phone will be iOS10.  iOS10 requires iTunes 12.5.1 find which demands in turn 10.9.5 OSX or newer.  Software update checks only the updates to the current version of the system that you are running but that itself can be updated.  It may or may not be possible to upgrade your computer to the system requirements. Find your computer on the web site of http://www.everymac.com model and near the bottom of the specification of the system section, he will tell what versions of the operating system, it is able to run. If you can not run a newer system, you will not be able to sync this phone to your current computer. OSX 10.9 and 10.10 are no longer available. You can try to install the free El Capitan OSX 10.11.  El Capitan can run slower on older machines and require the additional purchase of RAM (4 GB is a minimum realistic and many recommend 8 GB).  Making a big jump in versions of system is also more likely to affect the old software.

  At el capitan Snow Leopard, it will make my macbook is slow?  - https://discussions.apple.com/thread/7412959

  Course OSX Upgrade General information, including configuration required - http://www.apple.com/osx/how-to-upgrade/

• iTunes could not connect to the iPhone, because an invalid response was received from the device.

  Just bought an iPhone 7 today and received the error message "iTunes could not connect to the iPhone because an invalid response was received from the device." Don't know what that means, and I have never had this problem with one of my previous iPhones. Thank you.

  You run iTunes 7.5.1? iOS10 requires iTunes 12.5.1 find which demands in turn 10.9.5 OSX or newer.  Software update checks only the updates to the current version of the system that you are running but that itself can be updated.  It may or may not be possible to upgrade your computer to the system requirements. Find your computer on the web site of http://www.everymac.com model and near the bottom of the specification of the system section, he will tell what versions of the operating system, it is able to run. If you can not run a newer system, you will not be able to sync this phone to your current computer. You can try to install the free El Capitan OSX 10.11.  El Capitan can run slower on older machines and require the additional purchase of RAM (4 GB is a minimum realistic and many recommend 8 GB).  Making a big jump in versions of system is also more likely to affect the old software.

  At el capitan Snow Leopard, it will make my macbook is slow?  - https://discussions.apple.com/thread/7412959

  Course OSX Upgrade General information, including configuration required - http://www.apple.com/osx/how-to-upgrade/

  If you have any generation of PPC software which works under OSX 10.6 it is not supported in later versions of the system.

• -What it means and how to fix it? iTunes could not connect to the iPhone from the iPhone Simon Young, because an invalid response was received from the device.

  iTunes could not connect to the iPhone "IPhone by Simon Young", because an invalid response was received from the device.

  You have upgraded to iTunes 12.5.1? iOS10 requires iTunes 12.5.1 find which demands in turn 10.9.5 OSX or newer.  Software update checks only the updates to the current version of the system that you are running but that itself can be updated.  It may or may not be possible to upgrade your computer to the system requirements. Find your computer on the web site of http://www.everymac.com model and near the bottom of the specification of the system section, he will tell what versions of the operating system, it is able to run. You can try to install the free El Capitan OSX 10.11.  El Capitan can run slower on older machines and require the additional purchase of RAM (4 GB is a minimum realistic and many recommend 8 GB).  Making a big jump in versions of system is also more likely to affect the old software.

  At el capitan Snow Leopard, it will make my macbook is slow?  - https://discussions.apple.com/thread/7412959

  Course OSX Upgrade General information, including configuration required - http://www.apple.com/osx/how-to-upgrade/

  If you have any generation of PPC software which works under OSX 10.6 it is not supported in later versions of the system.

• I have re-installed Windows XP. My wireless does not, any more than my ethernet connection. What should I do?

  I have re-installed Windows XP. My wireless does not, any more than my ethernet connection. What should I do?

  original title: why isn't my laptop recognize the eathernet link?

  Go to your computer manufacturer's support web site
  and search for the Windows XP drivers for your specific computer or motherboard model number.

  If there are Windows XP drivers, then download to a folder on your hard drive and burn it to a CD/DVD.
  Then, after installing XP install all device drivers, start by installing the card mother/chipset driver first,
  then the SATA, Audio, USB, LAN, etc, drivers.

  List of computer manufacturer support sites:
  http://Windows.Microsoft.com/en-us/Windows/help/contact-support/computer-manufacturers

  If you have an Intel motherboard, you can try the Intel driver update utility: http://www.intel.com/support/detect.htm?iid=dc_iduu

  Graphics/video drivers:
  Check the download site of the manufacture of the graphics card for the newer Windows XP drivers for your card.
  ATI: http://support.amd.com/us/gpudownload/Pages/index.aspx
  NVIDIA: http://www.nvidia.com/Download/index5.aspx?lang=en-us

  J W Stuart: http://www.pagestart.com

• Unable to connect to wireless networks more. ("Windows could not connect to (SSID)")

  Hello!

  Something very strange is happening with my laptop (dv6-3060ee). Up to this day at noon, everything worked well, including the wireless network. So, I set my computer to Hibernate and came to the House of my parents. As I turn it on and try to connect to the wireless here, I can't. I get this error "Windows could not connect to (name of the network).

  I'm on W7 Home Premium 64-bit and the card wireless in an Atheros 9285 b/g/n (model number can be a problem, I have it does not properly check).

  Things to consider:

  -I don't know that this is not a router problem or hardware WiFi card because:

  1. I can connect to the router and get internet access on my phone and with the other computer normally.

  2. on the laptop, I can not connect to the network without wire inside W7, BUT with HP QuickWeb (this system of Opertaing before loading windows), I can normally connect to the network and access to internet.

  -Have you ever tried, without success:

  1 reinstall the driver for the wireless card / Unistalling the driver and install it again

  2. change the encryption on the router. (Even with no encryption I can't connect)

  3. of course, restarting the computer, turn off/on of the network card, reset the router

  So, I'm sure it's a problem with Windows. I did some research here and in other places and other people seem to have the same problem, but I couldn't find any solution.

  I didn't install any software today which could cause conflicts.

  So, can someone help me, please?

  Thank you

  Thank you for your help, but I'd already sorted.

  The problem was really the driver, an update had been installed by the HP update program and it makes the device stop working. This problematic driver was March, I can't remember the version number.

  I went to the Device Manager and pressed on "Roll Back Driver". Windows restored to an October/2009 driver, 8.0.0.238 version number, and now it works as it should.

• How to access the USB secure key on windows vista, I get the message that application 10004 could not find any JumpDrive Secure device connected to your system

  Original title: how access key USB secure Windows vista

  I have a lexar player sure to jump that I used with an old computer that has Windows XP.  I now have a new computer with Windows Vista and I can't access the secure part of the USB key.  When I try to access the part secure the USB key I have the following message "Application [-10004] could not find any JumpDrive Secure device connected to your system. Please make sure that your JumpDrive Secure device is inserted into a USB port".

  Of course, the USB key is inserted into the USB port.  If anyone can help find me a way to access the part secure the USB key I would appreciate it.  Thank you.

  Hi Jon0909,

  The error that you received can be for several reasons. I suggest you try the following steps:

  Method 1: Run the fixit available in the link below and check if that makes a difference

  Tips for solving problems of USB devices

  Method 2: This normal matter as a result of a conflict between the USB and other USB (Universal Serial Bus) connected to the computer.

  (a) disconnect all the external devices connected to the computer to expect the mouse and keyboard, check if your USB key works.

  (b) If this solves the problem, and then add back both devices until you discover the piece of hardware causing the issue.

  If the problem persists, you can contact the manufacturer of the device for any known issues
  http://www.Lexar.com/support

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer
  ---------------------------------------------------------------------------------------------------------
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Can I use CC on more than two devices (I have 3 Mac and 1 PC in the House) if I deactivate those that I do not?

  Can I use CC on more than two devices (I have 3 Mac and 1 PC in the House) if I deactivate those that I do not?

  Thank you

  Hi ingrid,.

  You can use Adobe Creative cloud on 2 machines.

  If you disconnect from the creative cloud on 1 machine which you use so you can activate it on another computer.

  Please see the help document:

  https://helpx.Adobe.com/x-productkb/policy-pricing/activation-deactivation-products.html

  Kind regards

  Sheena

• M1536dnf - the installation program could not connect to your device. Check the IP address

  I recently bought a LserJet Pro M1536dnf for my business, then we would have network printing and scanning. We have both Mac and Linux PC with a single machine Windows solitaire which is kept away from the network for his own protection, and I expect from Linux but this is not where the problem is. Due to our network configuration, the only way to connect to the printer is by IP, not not using Hello. When installing using the installer of HP on the Mac, I choose 'Add intellectual property arrangements', enter the IP (192.168.1.247) and click OK. After that, he always comes back 'the installer could not connect to your device. Check the IP address, make sure that the device is powered, and then try again. "I know I can get to the printer because I can access its web interface in Safari. I tried to reset, update firmware, reboots, power-off/power-on different computers, nothing works.

  Curiously, I could add the printer very well on Ubuntu Linux computers and print immediately, although the scanner still doesn't work here. So my problem is on the Mac.

  OK, I have now works. The HP installation program provided on the CD-ROM supplied with the printer does not work. After you download the new version of support.hp.com, I could successfully add the printer by IP address.

  Also, just a quick note to all the world using Linux (although it is not officially supported by HP):

  The printer works fine, using HPLIP, but requires at least version 3.11.1 to work. I had to add an additional to my linux installations software source to make it work.

  Under Ubuntu 10.04/10.10, add:

  PPA:hplip - isv/ppa

  Other Linux distributions will be different, if you are having problems check to see how to install the latest version of HPLIP software.

• OfficeJet6500A more - ePrint Setup error - this printer could not connect to the server

  My 6500 a is connected to the internet and I am able to print wireless.

  When you try to set up ePrint, I go through the following menu path: installing, configuring Web services, the printer email address.

  I get the message error "this printer could not connect to the server.

  I have read and tried the others 'solutions' on the plate that involved turning market eprint, crossing out-lit power cycles, turning wireless on and outside, turning on the printer and wait 5 minutes, restoration of factory settings...   Nothing works.

  Any ideas?

  From one day to the next it printed the ePrint address, so I guess that the problem was with the HP sever.

• ReadyBoost will not use more than 2 GB 'Cache space used' on 4 GB ReadyBoost.sfcache file

  Windows 7 64 bit on a computer laptop 4 GB.

  I have a card SD of 2 4 GB dedicated to ReadyBoost, connected via USB2.   I tried to format the card as NTFS and exFAT and in both cases, Windows may correctly fill in the card with a ReadyBoost.sfcache file, which is about 3.8 GB (card is dedicated to ReadyBoost).
  =============
  (Pasted image in - did not show when I introduced first)
  
  =============
  The problem is that no matter how long the system running, perfmon displays 'Cache space used' is always less than 2 GB.
  He goes up regularly in the first ten minutes after enabling readyboost, then levels: less than 2 GB:

  =============
  (Pasted image in - did not show when I introduced first)
  
  =============
  (Of course the "put bytes in cache" are greater because of the compression.)   But it seems to use only about 1/2 of the 4 GB cache file.
  I tried to adjust to only use a 2000Mo cache file size, and then 'Cache space used' would not exceed 1.4 GB.

  Am I something wrong or bad what do the numbers mean or is it an inherent limitation of ReadyBoost due, for example, General fresh metadata in the cache file?

  As I frequently have max on my use of memory and I can not install more than 4 GB, I had significant performance gains when he might have already spent several minutes, beating the pagefile.   I hope to see even more benefits with a bigger Readyboost cache if possible.   I would also like to solve this problem before investing in a larger and more efficient card.

  Thank you and best regards,

  Hi Jeff,

  In some situations, you might not be able to use all of the memory on your device to speed up your computer. For example, some flash memory devices contain both slow and fast flash memory, but ReadyBoost can only use fast flash memory to speed up your computer.

  http://Windows.Microsoft.com/en-us/Windows/using-memory-storage-device-speed-computer#1TC=Windows-7

  Computers with discs hard fast (such as 7 200 or 10 000 rpm disks) could achieve minimum performance gains due to the already high disk i/o ReadyBoost. will read the files from the cache only when this so will improve performance. Hard drives surpass flash in sequential reading drives, but flash drives are faster when no sequential reads (because of the latency caused when the drive head must move to a different disk sector). As a result, ReadyBoost reads from the cache only for non sequential reads
  http://TechNet.Microsoft.com/en-us/magazine/ff356869.aspx

  Hope the helps of information.

• Could Not Connect To Apple TV

  As the title says... "Could not connect to Apple TV"

  Its last 4th Gen and I just all of a sudden today get this message. No changes made to do anything. AirPlay works very well on my 3rd Gen on the floor. Switch to 'Living Room' and cannot connect. Summer works well for months and months.

  Tried to restart everything. Everything is up-to-date. Disabled firewall... (don't see why this is a diff when it works fine) Nothing happens... Same message...

  I'll have to do a reset here? Or is it something else.

  Any help appreciated thanks a lot,

  Mac.

  Try these steps, check to see if things work after each step if necessary, before you try the next.

  1. Check AirPlay is on the Apple TV (turn market if it already is)
  2. Check that both devices are on the same network (settings > Wifi on the mobile device and the settings > general > network, on the Apple TV).
  3. Restart the Apple TV (settings > general > restart).
  4. Restart the Apple TV by removing ALL cables for 30 seconds.
  5. Restart your router. (Also try to remove the power cord for at least 30 seconds)
  6. Restart your mobile device.

  If you're still having problems, the following article can help you.

  Troubleshooting AirPlay

  Troubleshooting connections and Wi - Fi networks

  Recommended Wi - Fi settings

  WiFi Diagnostic Software (for Mac users)

  You will also find help on this page, where I have collected some of the more unusual solutions for network problems.

  When you make adjustments to your network for better optimization, you can find some of the points mentioned onthis page useful.

• Error iTunes - iTunes could not connect to the store purchases - if you have any firewall software, make sure it has been set to allow communication on port 443.

  My itunes has been fine. All of a sudden today it now gives me this error: error Itunes - iTunes could not connect to the store purchases - if you have a software firewall, make sure that it has been set to allow communication on port 443.

  I do not have my firewall active. I connected to itunes, quit itunes, reconnected - still a problem.

  Was there an update and now it's a bug? Help!

  Thank you!

  Run the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  The title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  Click on the clear view icon in the toolbar. Then take an action that does not work the way you expect. Select all of the lines that appear in the Console window. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name or e-mail address, can appear in the log. Anonymize before posting.

  When you post the journal excerpt, an error message may appear on the web page: "you include content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• Windows could not connect to the Group Policy client service

  I get the error message after restarting my laptop with Vista Home:

  Windows could not connect to the Group Policy client service. This problem prevents limited users to logon to the system and administrative user, you can view the log of events system for details why the service did not respond.

  I'm the only user on my laptop with laptop admin rights works correct with few programs but it seems that I have no ADMIN rights now. I have not authorized for the restoration of the system, start-up ccleaner.exe, instalation of new software, etc.

  I tried this:

  1.
  

  http://social.answers.Microsoft.com/forums/en/vistasecurity/thread/bbfe3246-0ceb-4899-BFBA-7a98e642c009

  with hidden Admin, but for Admin hidden even in safe mode was not allowed to change my account more up/down.

  My laptop have orginal Vista and I have no bootable CD.
  

  2.

  http://social.technet.Microsoft.com/forums/en/winserverGP/thread/5de9f483-ff69-4fac-ac3f-601a62cc78d1

  result:

  netsh

  Netch > winsock reset

  Elevation of the requiries the requested operation.

  Help, please.
  

  Hi SSergo,

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in theTechnet Group Policy Forum

  Lisa
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Want 4500: Connection error! The printer could not connect to the server

  Connection error! The printer could not connect to the server!

  Cannot set up eprint or update the driver. Ever been on the forums and do not understand what to do!

  I am successfully connected to my router and can print from my pc and my ipad with airprint.

  PC "will not find"the printer either for purposes of updating

  What I need to change the DNS. If so, I don't know what it is or how to do it!

  I went to the ip address but was unable to click on "wireless (802.11)", as recommended by a last response forum, as the next low 'status '.

  Can anyone help?

  Very frustrated customer :-(

  Hi @roopuk,

  Thanks for getting back to me.

  Sometimes the manual DNS 8.8.8.8 / 8.8.4.4 won't work in some configurations of network users.  Try the same steps as described above, but this time use the following parameters:

  Manual preferred DNS Server: 209.244.0.3
  Auxiliary manual DNS server: 209.244.0.4

  If you encounter the error, as before, we take our proverbial gloves off to try a more intensive troubleshooting.

  What is happening, it is that your router allows your printer connection that to enable wireless, but not a secondary connection to Web services.  In order to get these devices to 'shake hands' a second time, you may need to enable DMZ mode on your network through the router's built-in Web server.  HP does usually not this configuration for its customers as errors can cause serious network problems, but I can certainly post the info you need on your router or the ISP of the staff support company so that they could help you directly.

  Here is the information that you need for your provider service to open ports on your router/modem...

  -Multicast must be enabled
  -Hello enabled for AirPrint (relevant for iOS and Mac OS users)
  -Mac filtering should be disabled
  -Also, make sure that your router's firmware to date if
  necessary
  - The dmz on the router mode and turn it on to the printers IP address: _

  Ports to open are: Eprint and Apps

  Incoming Ports.

  UDP
  80
  443
  ------------------
  Outbound ports

  TCP
  5222
  5223
  -------------------
  Once they are open, you should have no problems connecting to services web eprint on your device.

  I would like to know how it works for you.

  Kind regards