CP1525NW COLOR: PRINTER POWER SUPPLY MANUAL

Similar Questions

• LaserJet CP1525nw: CP1525nw color printer leaves magenta spots to the left of each page

  My CP1525nw color printer leaves the magenta veins on the left side of each page to print.  I tried to clean the printer using the clean function built into many times I removed and cleaned the amgenta cartridge, and I also deleted every piece of software my machine HP and reinstalled the drivers for this printer.  Magenta strekas are still there. They are always on the left side of the page.

  someone had this problem a few years ago and an answering machine seems to have responded with a link to a wrong page

  Is there a solution or a work link pleaase?

  Well, it's obvious that you're upset.  I'd be for.  To make this real simple.  You have a bad magenta toner cartridge. Cleaning will not work because the wiper inside the toner cartridge blade went probably bad toner causing the flight of this side and causing the problem.  Replace the magenta toner with a new toner hp original and all should be good.

• 3525 Deskjet printer power supply problem

  Brand new printer, I have been connected, printed OK. Once off, lights not again unless you pull on the power cord plug, then plug it in yet. Then can be turned on. But once off so the same problem all over again. I tried different plugs/Sockets, same problem with them all. Same thing happens when the printer is connected to the electric network without being connected to a laptop Desk/computer. Is this a power supply problem? Is it not ridiculous to do out of the box?

  Thanks for any help,

  Nicholas

  Hi Nicolas,.

  The latest firmware should solve the problem you are experiencing.

  Download and install the update of the firmware for your operating system below:

  32 bits:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-128070-2&cc=us&DLC=en&LC=en&OS=4157&product=5241265&sw_lang=

  64 bit:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-128071-2&cc=us&DLC=en&LC=en&OS=4158&product=5241265&sw_lang=

  If the printer connected to your PC via the wireless network and the update fails to install, connect the printer with a USB port in order to complete this update, or update your device from its screen as follows:

  http://support.HP.com/us-en/document/c03250770

  Kind regards

  Shlomi

• HP LaserJet CP1525nw color print quality problems

  I got a HP LaserJet CP1525nw color about 2 months ago. After about 4 weeks, I noticed a print quality begins to degrade. Black started first by streaks and fading. Now when blue prints starts to show streaks and melted a magenta pink. All cartridges are at 50 percent of capacity or more. Any ideas about what to check?

  Hello Graf213,

  There are a few things of different which could cause print quality begin to deteriorate on printouts. My guess is that the printer may need to be cleaned and / or calibrated.

  Troubleshooting HP article addresses print quality issues, and provides for the issue of many resolutions.

  Solving print quality problems

  Perform the steps, and I would like to know the results.

• Printer power supply fried?

  is my printer DOA if it does not supply power to the top? power adapter fell on the floor, & when reconnected, the printer went crazy with lights & messages for the power, which I did. Now it turns on again.

  the screen flashes once when it is plugged, then darkens. Bought another card, or one run.

  Looks like it is broken, but to know for sure you would need to go into a computer store and have someone to watch.

• HP 3520e all in one printer, power supply problem

  Recently off my 3520e all in one printer when you go away, come back after 2 weeks and can't turn it back on.

  All the cables are connected and power is available, but will not turn on/off button.

  Ideas please

  Hello John-FB,

  Please click here to access document that should help you to solve the problem.

• HP CP1525nw color: needing a new HP laserjet and want to get one that uses the same previous cartridges

  My printer HP laserjet CP 1525nw Color has finally succumbed to a slow death and I JUST bought 15 cartridges that cannot be returned.  How can I locate a new laserjet printer that uses these same cartridges?

  Thank you!

  According to the HP store (see http://store.hp.com/UKStore/Merch/Product.aspx?id=CE320A&opt=&sel=SUP#merch-comp-products ), the HP 128 has cartridges can only be used with the following printers:

  • HP LaserJet Pro CP1525n color printer
  • HP LaserJet Pro CP1525nw color printer
  • HP LaserJet Pro CM1415fnw color multifunction printer

• Color Laser Jet MFP M277n Pro: Power supply flashing

  Just set up this printer.  I've not turned off because I think he's using the toner when you next turn on the.  Is this correct?  But now the power supply light flashes.  Is this normal?

  Without doubt, it entered into mode 'sleep'.  Hit the button on the screen which should come on and the power button should now be solid on.

• Printing a document of power supply for PC farm

  I have a Buffalo print server model: LPV2-USB-TX1.

  My PC is a HP Pavilion A6230N (GN561AA)

  Processor: Athlon 64 X 2 5600 + 3 GB DDR2 400 GB NVIDIA GeForce 6150 SE

  OS: Windows Vista editions Home Premium Service Pack 2

  When I print a document to the printer my PC just turns off.

  No blue screen. No memory dump. As someone just came out the power cord.

  If I print from my laptop the Document Prints Fine, but my PC turns off always just.

  I guess the print command that is sent to the network turns its power supply to my PC.

  Ports? Motherboard? Processor?

  Hi Vista_curious30,

  A. which application you want to print?

  B. Since when are you facing this problem?

  Try the following steps to refine the question.

  Step 1

  Check the event viewer.

  What are the information in event logs? (Event Viewer)
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer

  Step 2

  Put your computer to boot in order to verify if there is software conflicts.

  A clean boot helps eliminate software conflicts.  Let us check if software is causing the problem by following the clean boot procedure.  To perform the clean boot procedure, follow the instructions in the link below.

  Step 1: Perform a clean boot
  Step 2: Enable half the services
  Step 3: Determine whether the problem returns
  Step 4: Enable half of the startup items
  Step 5: Determine whether the problem returns
  Step 6: Resolve the problem
  Step 7: Reset the computer to start as usual

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135

  After checking the problem, turn the computer back to theNormal mode. Uninstall or update the program that is causing the problem.

  Step 3

  Try printing a test page.

  I hope this helps.

  Bindu R - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think.

• OfficeJet Pro 8500 a-green power supply light on-Quit printing using as a copier

  I was using the printer as a copier, placing documents on the glass and close the cover.   About 8 different documents, then the printer just quit so that, in the middle of printing a page printed.   Green power light is on, but when I push it, it is not off. Touch control panel does not respond.  Nothing seems to function.   Tried to unplug the power cord at the back, unplug the unit from the wall and disconnect the power supply cord.  Plugged everything back in after about 10 minutes to be disconnected and no help.  Green power light turns on but no function doesn't seem to work.  Have windows 7, 64 bit HP computer, but the copier function should work even if not connected to the computer.

  Appreciate any help.   Thank you

  Carl

  It seems that the firmware may have had a fatal error occurs. I'm afraid there is little you can do to solve the problem. Try the procedure described in the document below. If this does not work, you will need to replace the printer.

  http://goo.GL/aNuHW

• Printer HP CP1525nw Color Laser Jet not print wireless with Win 7.

  My HP CP1525nw Color Laser Jet printer will not print wireless with Win 7. It is not recognized as a wireless device when by Win7 'add a device '. It has worked very well in the past, but now I have to connect the printer with a cable to be able to print.

  Thank you in advance for your help!

  Sakii305

  Hi Sakii305,

  Thanks for posting your query in Microsoft Communities. The problem description, I understand that you are not able to print wireless. Provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  ·         You use a third-party security software?

  Follow these methods.

  Method 1: Temporarily disable the security software .

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow the steps in the article.

  Solve printer problems

  You can read this article for more information:

  Why can I not print?

  I hope this helps. Let us know if you need more assistance.

  Thank you.

• Compaq Mini 110: Polarity of power supply jack

  Hello

  I have a HP/Compaq Mini 110 that was given to me because both the battery and the AC adapter was lost. I have a power supply of the correct voltage (19 VDC) and can get an outlet of the right size. I need to know what the polarity of the plug must be, for example, is the center of the end positive or negative? I also need to know if the computer will be also powered if one battery (even dead) is not installed. If it will power-up with the polarity a/c adapter, I'm going to buy a battery, otherwise I don't lose money. Shame on HP/Compaq to not show a pictorial of polarity on the camera body. If I can get going, have enough moxie upgrade to Windows 10? Thank you.

  Here is the Service Manual:

  Manual

  See p. 54 on the hard drive. She straight plug the motherboard, but it shows a cart or make sledding which does not move there and the SSD is welded to a SATA connector. For some time I took one of these apart.

  He's a regular SATA and the size limit, it's what is on the market, not the hardware, so you could theoretically install a 2 TB or a 2.5 inch SATA SSD. You could probably get one inch 80 gig SATA SSD 2.5 for a pittance and it would run as well as he is capable of running.

  The memory you have is DDR2-800, but the system he clocks up to speed DDR2-533.

  The power Jack is soldered to the motherboard and there is no way I know to stretch upward. A lot of youtube videos on the welding on a new jack and you can find the plug for a few dollars. It is not a work that I do, but I saw several times and I think you can probably manage it if you have the soldering equipment.

  If this has answered your questions please make it easier for others to find by marking "accept as a Solution.

• Satellite x 200 battery or power supply issues

  I have a satellite x 200 - s20. Owner since new, 2 and a half years.
  The laptop works perfectly, but I don't know if I need a new battery, power or maybe there is a hardware problem (but I doubt it).

  When it is connected to the power outlet, provide the following happpens:

  He started using the battery instead of the power supply.
  Power and battery leds turn on and turn off (on during a few seconds and then off for a few seconds).
  At this point, the battery stops charging.

  In the manual it mentions something on one of the lights turn blue, none have ever done that.

  Hope someone can advise
  Thank you
  Strand

  Hello

  In my opinion, you should first check if the power adapter is not a malfunction.
  If the AC adapter would work properly, then the battery might not be charged and the battery led not turn to blue because the battery is not fully charged.

  I would recommend so check the AC adaptor first.
  Of course this is only my personal opinion and I could be wrong too

• Equium A60 power supply insulation question

  My laptop recently failed a PAT to trial because of the continuity of the Earth. For background, it's a laptop bought UK but I am running an advance Australian 3-pin into the power adapter as I am in Australia.

  I saw somewhere on here that standard satellite UK does not connect through the Earth and I wonder if someone can confirm the preference for an official title, because I believe that this is the cause of the problem, but it doesn't seem to be, for example, a symbol 'double insulation' on diet, nor the manual referred to - the laptop works very well and I have no reason to suspect the power supply are faulty.

  So wonder if it actually has a pin plug 2 (UK power points need the same if taken earth it is not connected, Australian points are not).
  I really need to resolve this issue I need to use my laptop on the site, but can't until he gets that agreement and I do not want to get a new (OEM) power when I do not think the existing one is broken, so I need something to test guys and show them that it is a normal behavior...

  Of course, if this isn't normal behavior, I would be better to know now!

  Thank you

  I Don t think that the power supply is broken, and it doesn't really matter what the wall of the AC cable is connected from the regulated AC adapter voltage by itself and has it s own ground.

  Maybe the PAT test fails, but food is not broken.

  Welcome them

• HP PSC 1510 all in one printer power button flashing key.

  The power button flashes. No other lights are on.  I can not turn off the printer.

  Hello Laureldawn,

  I see this is your first visit with us here on the Forums of HP. Please, let me take a moment to say 'Welcome. '

  I have some suggestions that we can try when troubleshooting flashing lights on the printer.

  First of all, please make sure that you have the printer power cable connected directly to a wall outlet and NOT a bar/power strip.

  Here is a document that uses a LaserJet printer for example, but it is intended to be used by HP products in general.  This document explains the problems when connected to an uninterruptible power supply/Strip/surge protector power.

  Another step we can try is the document the Treaty of lights flash.

  Please let me know whether or not these measures have helped.

  If I don't hear from you today, I hope you have a great Wednesday.

  See you soon,.