CQ62-410us screen

Similar Questions

• CQ62-410US stuck with "Several monitor - Clone View" and VGA port does not

  Hello!

  I have a Compaq CQ62-410US computer laptop with an Intel GMA 4500 M (onboard) video card and a port output VGA, Windows 7 x 64 operating system. A few weeks back the screen was broken (kick straight punch of a child) and nothing could be transmitted via the VGA output either, but the laptop booted and I could hear the sound of Windows 7 logon. I never checked before the VGA output port.
  Yesterday, I replaced the screen broke up with and identical. The fine (full-screen) display in case of back work (boot from USB Flash and the sea + test images), but in Windows 7, two vertical black stripes appeared on the sides because lower than the native resolution. The resolution can be changed at native 1366 x 768 "Screen resolution" because the display is set by default to "Multiple monitors" (I have no other monitor connected, only the built-in screen) and "display of Clone. The built-in display is set as secondary and 'Generic non - PnP' is defined as primary. Any attempt to set the integrated display as primary function or to change the mode "display single" / "Extend view" leads to a black screen with the backlight always on, no matter where I change the settings - in the 'screen Resolution' or 'Graphic properties' (from driver Intel). In the 'Screen Resolution' window the pictogram of the screens show a single screen split in two, and when I press the button "Identify" it shows on the screen ' 1 | 2 ", as you left half of the screen is the main display and half right is the secondary display.
  I put a Philips monitor to the VGA port, Windows detects and installs the appropriate driver, but there is no picture any of mode I put - Clone, Extend, unique display - monitor.
  I tested 3 view of the site of Compaq drivers for my device and the GMA 4500 M drivers from Intel, but the problem is the same (with the drivers from the site intel, on I get only black screen with backlighting.) Pilots are unstable, sometimes at the opening session, page is only a black screen (but before the windows loading screen appear very well) that cannot be changed by "Fn + F4" / "F4" (change view) but a black with the backlight is turned off.
  Due to the replacement of the hard disk, I can't use restore of the operating system that is installed at the factory.
  Please advise me how to solve the display problem and enable the port VGA (get the image on the external monitor).
  Thank you in advance.
  SSM there is not output through the VGA input even at the BIOS screen (no material or to issue independent of the operating system support?).

  I have attached a screenshot.

  Update: I started a live Knoppix CD, and I don't find any problem - unique in 1366 x 768 display configuration; I could even play a game in 3D (OpenGL). While hanging from one monitor to the VGA port, it was found, but when trying to print image to it the OS hung. I guess it's a hardware problem, something to do with the video controller.

  

  I thought about it, it's the GPU, I think that some of the contacts are damaged. Today even in the BIOS screen I see in the middle of the screen a vertical thin purple line which was bounded two screens on a single screen, and all now have a purple tint.

  I had a quick glance at the GPU and surprise - it is glued to the motherboard, no sleeve, no welding. The motherboard chipset is also stuck.

  See the attached images.

  Thank you for the excellent support. I will never buy anything with Compaq logo on it.

• Compaq CQ62-219WM showing black screen AFTER the replacement.

  So I guess my question is fairly simple.  When I replaced my client on their Compaq CQ62-219WM screen and it appears black.  When I shine a flashlight in it, I see the start menu and whatnot.  This means that I must file a RMA right? I'm guessing that because black light is out.

  Indeed, the Assembly of replacement LCD display screen could be faulty. You meant was to request an RMA from the supplier that you used with the supply of a replacement. Yes, in this case, I would like to request an RMA number.

• F8 locked in the installation of XP EULA

  I have a CQ62-410US and I'm doing a clean install of XP Pro 32 bit on a brand new Seagate 500 GB disk.  I used nLite for XP slipstreamed install CD and everything worked until I reached the point in the configuration where you must accept the EULA.  To do this, it need to press F8, but F8 appears to be locked.  No other keys are locked.  I tried to use a keyboard USB external, the same question.

  Has anyone encountered this problem?

  Thank you

  RACER

  Hello

  Try to hold down the fn key as you press f8.

  Kind regards

  DP - K

• Network Controller is not found"error message appears in the DEVICE MANAGER

  Hello! I installed WIN 7 Prof 64 bit on my laptop Compaq Presario CQ62-410US and Device Manager shows that the ETHERNET CONTROLLER is not installed correctly. I've been using the appropriate drivers:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=5048...

  I tried to find a solution here:

  http://support.HP.com/us-en/document/c02592699

  "But the" 'LAN Power Saving ' option of "System Configuration ' component is missing.

  I uninstalled installed new driver LAN wireless with no result.

  Thank you very much for your help! Miron

  Hello:

  See if it works... Now, it's to install the Ethernet controller (wired), not the wireless network controller.

  Make sure that you have installed the first Intel chipset driver, then restart.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-87204-1&cc=us&DLC=en&LC=en&OS=4063&product=5048735&sw_lang=

  Then install the ethernet driver second on the list at the link below:

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• Compac cq62: downloaded windows 10. Now I have a black screen and the caps button continues to blink. All the answers.

  Downloaded Windows 10. 1 week later, I have a black screen. When I turn on the power to all I get is a flashing caps button one am not able to connect. Ilha a Compaq cq62 model.

  I have seen this reported, and the response is not good, sorry:

  "Problems of upgrading Windows 10: black screen after update (new).
  Some users taking advantage of the Windows 10 upgrade are the conclusion that once the completed upgrade their device just gives them a black screen and does not start.
  Microsoft is still working on a fix for this, but it's not a way to avoid it now. Worse, it seems that the problem that happens on multiple PC configurations. For now, we can only suggest using the utilities provided with your backup device and create some external media backup before starting the upgrade in case that happens. If this happens and you live near a Microsoft Store, make an appointment with them to have your device looking if you experience the problem. Some reports (such as those of our comments) indicate that disabling anti-virus programs before performing the upgrade prevents this issue. »

  http://www.GottaBeMobile.com/2015/07/30/7-Windows-10-upgrade-problems-how-to-fix-them/

• Where to buy the new screen? Compaq presario cq62-206SO

  Model Compaq presario cq62-206SO

  The best would be 100 USD or less shipping and display. I live in Norway.

  Note * I looked on eBay but I find not all screens for my model

  Try laptopscreen.com.  They ship all over the world, and the screens are usually less than $60.

• Compaq CQ62 screen lights with caps lock stuck.

  Hello

  My computer compaq laptop is a month old. When I turn it on, I hear the fan, but that's all. No beeps and the only visible light is the caps lock key, which does not turn off. The screen is completely blank. No cursor blinking, no music windows, nothing. I tried to turn it on using only the stored battery power - no luck. I turned on and off several times - no luck.

  Thank you very much in advance for any advice for helping me fix this very premature!

  Kate

  Hi Kate,.

  Try the following.

  With the laptop off, remove the AC adapter and then remove the battery.  Press and hold the power button for a minute.  Plug the power adapter (leave the battery) and see if the laptop boots.

  Kind regards

  DP - K

• CQ62-209wm: CQ62-209wm turns on but does not rest on the black screen

  This same question was asked in 2013 but was never answered. The proposed answer was to run diagnostics on the hard drive and memory. My laptop has exactly the same problem and I have the tests. Everything going smoothly. I finally decided that the video was out so I had a bad mother. Well, I ordered a new card mother and new battery new memory. I pulled the heat sinks cleaned the CPU, cleaned the fan and cooling fins, and then replace all. Guess what people, it is still the same as before with these new rooms. No beep codes are generated, without sounds, etc. What happens is the caps lock light flashes approximately every 3 seconds and the WiFi symbol stays orange. He never blinks. I found the light accidentally code page, but there is no reason to corosponding between codes of light and the flashing cap lock key. It will just sit there and blink as long as you leave it or until the battery going dead comes first. This same problem has been around since I found a multitude of messages about this and this is not only a model. Forums in the world have this posted on them.

  So how about it HP engineers. Is there anyone of you ready to take on this problem and tell us how to solve this problem once and for all? I'm tired of having a computer that works only when it wants too. I want both of my laptops CQ62-209wm to work. I am able to get laptops to start completely about 35% of the time. In order to make their work I remove the battery, plug in the power supply, replace the battery and then try to start it. Sometimes it works most of the time, this isn't. I'm starting to suspect a possible in the power circuit problem, because it is the first laptop I've ever used or owned not illuminate if there is no battery installed.

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers.

  If you are unfamiliar with the operation of the function of private messages of the Forum, this post has instructions.

• Windows XP on Compaq CQ61-410US

  Hello, I recently bought a Compaq CQ61-410US and he was giving me no trouble. I need to install Widnows XP out there because I need to run programs that won't run in Windows 7 Home premium x 64. So I tried to slipstream drivers and all, but I get the blue screen whenever I try to boot from the CD. It is more lilely drivers sata but I tried to get every possible sata to slipstrwm inside drivers. If you don't mind, could someone write me a walkthrough on this? Thank you!!

  CherylG has provided a procedure step by step to downgrade to Windows XP, CQ61 series models. This is mentioned in the thread Part3 in the following link:

  http://h30434.www3.HP.com/T5/operating-systems-and-software/General-XP-downgrade-Guide-for-HP-laptops/TD-p/83267

  Here's another thread by Daniel who possesses the necessary driver information for Windows XP:

  http://h30434.www3.HP.com/T5/operating-systems-and-software/SATA-drivers-for-XP-solution-on-0x0000007B-BSOD/TD-p/114120

  Hope this information helps.

• Change HP 2000 - 410US (no touch) to TouchSmart PC

  I would change my HP 2000-410US to a one TouchSmart screen. Is it possible to do it and where can I find a reasonable price online?

  Hi @Zuri-Yejide94 ,.

  Welcome to the HP Forums!

  It's a great place to find answers.
  You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums Learn how Post and more

  I understand that you want to install a touchsmart on your laptop screen.   When I checked your HP 2000 Notebook PC Maintenance and Service Guide there no touch screens are listed for the replacement. (Chapter 3, page 17, section 1)

  It may be possible, but it would be unsupported and the result would be unknown.

  I hope this helps.

• disk failure hard compaq presario cq62-231nr

  My compaq presario cq62-231nr (product # XC434UA #aba) stopped working last week and I took it into the store of the computer it is diagnosed. They said that the hard drive has failed and they were unable to get all the files out of it. They wanted about $200 to fix so I just brought home. I bought a hard drive to it (500 GB hitachi) and when I install it myself. I have 4 dvd recovery disks that I made for her when I bought it there are 1 1/2 years. Never done this before so I am a little worried about smooth how it will go. My questions are:

  1-will the recovery discs works

  2 - 500 GB hard drive will I put actually no difference from the old hard drive was a 320 GB

  3 - What steps should I take after I put my hard drive in and start it (insofar as the use of the recovery discs)?

  4 - I need a key at any time in this process? I don't have one that I know of.

  Any help is appreciated!

  Hey, Dan:

  You are the very welcome.

  You have almost...

  When you turn on your PC for the first time after installing the new hard drive, you must press the F9 key to the HP welcome screen.

  This will give you a few startup options.  Your DVD player should appear as one of these options.

  Don't do anything about the selection who again. First, open the DVD drawer and insert the diskette 1 of your set of recovery disks. Close the door and wait a moment – just a few seconds.

  Then select the DVD - ROM drive in the list of the bootable devices in the list of startup options.

  Follow the instructions on the screen.

  You never know how long will last the electrical components.  This is why it is always advisable to keep the backup files.

  There's an old saying... "It is not a question of if a hard drive will fail, but a matter of time."

  Paul

• Failed to retrieve Compaq CQ62-217AX

  Hello

  I have a compaq laptop CQ62-217AX, and I have recently run recovery on it, and after that the laptop finished recovery process has restarted and showed a bar that says Windows load the files, then he quickly vanished and changed to the loading screen 7 Windows and after that a prompt is displayed in windows and dialogue full screen then stands up and says "recovery did not complete.

  I have re recovery plant performance with the same result and cannot operate, I should mention that I don't have the original abd HDD 320 GB I have a 750 blue digital Western in the laptop.

  I would appreciate help.

  Thanks in advance

  HI and thanks for your response

  I was able to get the recovery yesterday working media and the laptop restored without problem.

  Thanks a lot for your help.

• How can I install Windows XP on windows 7 laptop Compaq Presario CQ62-215DX?

  I want to install XP on my laptop (laptop Compaq Presario CQ62-215DX) which has Windows 7... give me some advice please

  You replace the startup disk in the BIOS cd. Then boot from the XP CD. And press a button when it tells you. However, he will wipe away Windows 7. So, if you want anything copy everything you want (with the exception of programs), before formatting the hard disk.

  NOTE: XP has no drivers for most of whats on the system (LAN/Sound/player card etc.). So if that is the only computer you have, go to HP site for this laptop search, download drivers and copy them into something. Before you begin. Or you won't get back on the internet...

  Also NOTE: If the disk hard in it is SATA, you will need to disable the AHCI in the BIOS (change it to IDE mode). Or XP will crash before you get to the configuration screen. Unless you download the SATA drivers, unzip / extract and add them when it says press F6 (on a floppy disk).

  The XP CD does not have SATA drivers on it either. If you do not add the SATA drivers during installation, do not change this back to AHCI after installing XP. Or it will crash

  In addition, make sure that you have a XP key. A key to windows 7 will not work

• HP Compaq Presario CQ62 blank display, solid caps lock light light orange, solid f12

  Good afternoon

  Currently, I'm stumped on troubleshooting lights error code for a hp compaq cq62 customers. I tried the hard reset, the reinstallation of the memory and even plug the laptop directly into the wall instead of a surge protector with battery removed. I can't find any solution on the HP site or any other site of forum for this issue as to what a solid caps lock light and a solid orange light on the f12 key.

  Currently I think the customer may need a new back light system or a new processor. Before to come to this conclusion, I hope that there is a clear solution for my problem. Thank you for any assistance.

  Hello @NotURt3kSupport ,

  Welcome to the HP Forums!

  I understand you are having problems starting your PC clients laptop Compaq CQ62.

  A single glance on the caps lock light usually means it is a failure of the CPU and requires a replacement of CPU or the motherboard.

  Also try to go through these documents to resolve startup problems:

  Computer does not start and the lights blink or the computer will beep.
  Troubleshooting of the black screens with no start-up or start-up error message.
  Tests of hardware failures (Windows 7, Vista) or hardware failures (Windows 8).

  You can tell if the backlight is the issue or start by plugging in a VGA monitor to see if the screen is displayed or not. If this is the case, you have on the laptop display problems. If it isn't, you're dealing with a problem of CPU, GPU or motherboard.

  Also, it would be useful to know what product and the operating system you are using. For more information on the search for your model and product numbers, click here: How can I find my model number or product number? What version of Windows you are using, click here: Windows operating system am I running?

  In the event of hardware failure I suggest you contact the services options HP telephone support. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.

  Hope this information helps!