CR1000 are accessible using NOR-DAQ?

Similar Questions

• Problem setting Legacy DAQ board using NOR-DAQ 6.1 for Labview

  I know that the Board of Directors is an old legacy product not supported by NEITHER, however for a low-budget project, I have 3 of these AT-MIO-16 x cards and the need to use them.

  I know I got this job in the past not distant os, however, for the life of me can't get things sorted and work.

  You use a NT box, in which this configuration used to work... uninstalled and started fees for other reasons, and I can not get the NOR-DAQ 6.1 to support LAbview 6.1 or 7.1.

  Of course, I understand the OR-DAQ 6.1 should be used for Labview 5 and older, but also know this has been successfully done in the past.

  I downloaded all knowledge base articles dozed or both support and remember to use successfully the last time that I set up so I know not somehow it works.

  My configuration is: AT-MIO-16 X to the bus combo board (called work)

  NT PC

  LabVIEW 6.1 or 7.1

  NOR-DAQ 6.1 is the most recent to support this card.

  However, it will not install its support to its latest versions of Labview and I get errors, crashing, or missing files, when I followed various circumvention of knowledge base solutions.

  I was hoping that someone has a documentation somewhere how to handle this, because it really is a matrix of spaghetti.

  I can get NOR-DAQ support files installed, and Configuration Manager works well, finds the map and allows its parameters to be defined.

  But when I load the DAQ vi of any type, Labview accidents and the wizard of data acquisition channel does not work at all (no error).

  Thank you

  Yes, the installation program from the folder of disks for NOR-DAQ 6.1 on the ftp site has worked well.

  Workaround. Thank you

• How to define logical tristate using NOR-DAQ 6212 in c#

  Hello world

  I am very new to NOR & help each of you experts out there.

  As the subject says, I'm trying to set digital output at tristate DAQmx & c# channel. I found the link on the Tristate property, but I don't know how to use it. http://zone.NI.com/reference/en-XX/help/370473H-01/mstudiowebhelp/HTML/bd33b0d/

  Any help would be much appreciated!

  Thank you.

  Hi kasrus,

  You set the property using the following syntax (after creating your task):

  digitalWriteTask.DOChannels.All.Tristate = true;

  As help document states: "you must commit the task for this setting to take effect."  The help document also highlights when the value of property compared to a reading or writing.

  This refers to the status of task template DAQmx:

  State of task model

  http://zone.NI.com/reference/en-XX/help/370466AC-01/mxcncpts/taskstatemodel/

  Methods of configuration will move your task through this model of the State, but you can also control using the syntax in the article below:

  Check, committing, start and stop of NOR-DAQmx tasks programmatically

  http://zone.NI.com/reference/en-XX/help/370473H-01/mstudiowebhelp/HTML/verifycommitstartstopdaqtask/

  Kind regards

  Kyle S.

  Technical sales engineer

  National Instruments

  http://www.NI.com/support

• Conversion of a VI that uses OR-DAQ traditional to NOR-DAQmx

  Hello

  I'm trying to convert a VI that uses OR-DAQ traditional to NOR-DAQmx.  I'm almost there, but when I run my new rear version number 'read' and 'scan' are not the same.

  In the original version the "number read" always came back as 1 and "scan" backlog is always returned as 0.

  In the new version, "number readings" and "rear scan" could come back with any value.  It's sure to shake my recording of measures and VI the interaction with the rest of the program.

  I have attached a light version of the VI for the old OR-DAQ traditional and new OR-DAQmx that illustrate this problem.  The two VI is written in LabVIEW 2011 SP1.  I would be willing to upgrade to SP1 2013 LabVIEW if it would help solve the problem.

  I would be grateful for any guidance.

  Thank you in advance.

  I think I did.  Use-1 to erase everything in the buffer when the program is waiting for the countdown to the end and then just ask for 1000 measurements when the countdown reaches 0.  Do not need the Scan back or number reading.  Also don't need to add the measure in table 1 at a time because I get them all at once.

  I enclose a copy of my solution for all those who might need to do something similar in the future.

  Gary

• NOR-DAQ traditional to NOR-DAQmx

  I am a neophyte of LabVIEW.  I inherited a previous employee long gone from the company, so that I work a LabVIEW project.  The project has been written using NOR-traditional DAQ and I need some update OR-DAQmx so that it is 64-bit capable.  Of course, I ran into trouble with the VI first that I try to put in level.

  This VI was built with LabVIEW 2011 SP1 and I need to replace the Config AI, I start, I Read, Index channel, control and HAVE clear screw with their equivalents of NOR-DAQmx.  Upgrade to SP1 2013 LabVIEW is possible if that makes things easier.

  Now here is the tricky part.  I want to keep the terminals on this VI even if possible.  This VI is used in several places and a few different programs and I want to make the change as minimally invasive as possible.  If possible, I want the changes must be made within this VI.

  I am looking for any help and or advice. Thank you.

  First, abandon all hope to keep the same connector components.  It is possible, but it's foolish to try. (Just trust me, OK?)

  Read these articles in the knowledge base

  http://www.NI.com/white-paper/3021/en/

  http://www.NI.com/white-paper/4342/en/

  What you're trying requires skills usually not developed in a neophyte of LabVIEW. (And you start with the 'Spaghetti' code - this is not 'Fun') Do an internship of audit and meet with your representative local of NOR.  Chances are that some local expert advice will point you away from some serious mistakes.

  Take care

• Verification of task names valid in the basis of NOR-DAQ

  Hello

  I have a question about the configuration of the tasks in the version of Base of NOR-DAQmx (I need basic because the application will need to be able to run on both Windows and Mac computers). The material is a box USB-6009, ordered through LabView. When you create a task inside LabView, is it possible to tell if the name you choose is already in use or not?  Similarly, is it possible to get a list of and if all tasks are running?

  The context is that I have a subroutine that made a brief burst of acquistion of analog input and then passes the result to the caller. I would like also to the subroutine to run standalone for different testing purposes. Normally, I would have the subroutine create and configure a task, the measure and then close the task. The problem is that the process of create/set up/start takes about 200-250 milliseconds (the measure itself is about 20 ms) that is long enough that I don't want to go through it whenever the subroutine is called from the top (I need to call this routine and do some other stuff a few times per second). So what I would is have the name of the task as a control on the subroutine, test that the value is a valid and if not valid only the initialization/etc. in the context of the subroutine, but if the subroutine has been passed a valid task from the top to skip a step all the time.

  Looking through all of Base of NOR-DAQ functions, it doesn't seem to be something that allows me to do this kind of check with the exception of brute force to try to create a task and trapping so all errors that might be generated.

  Suggestions (or ways) welcome.

  Kelsey,

  It seems that the property node is a component DAQmx, not a component DAQmx Base .  I can't find any DAQmx Base property nodes.

  dmsilev,

  Try to replace the property node of the tasks with the DAQmx Base get tasks.vi.  It is not in the DAQmx Base palette. It's a Subvi DAQmx Base create Task.vi.  Caution: when you use a Subvi, which isn't on the pallets, know that they are generally not documented well and are subject to change in future versions of LV

  

  If you weren't aware, DAQmx Base is written in LV and almost all the diagrams are not p [rotege so you can look inside and see how things are doing.

  Lynn

• How can I create a Windows using NOR-DAQmx application in Visual Studio 2010 64-bit

  Hello

  How can I create a Windows using NOR-DAQmx application in Visual Studio 2010 64-bit?

  I'm transferring a 32-bit application on 64-bit.  In visual Studio, I added the 64-bit project configuration.  He compiled the source very well but the reports link errors:

  error LNK2019: unresolved external symbol DAQmxReadAnalogF64 referenced in function NI6008_AnalogInput NI_6281\NI6281.obj
  error LNK2019: unresolved external symbol DAQmxCreateAIVoltageChan referenced in function NI6008_AnalogInput NI_6281\NI6281.obj
  error LNK2019: unresolved external symbol DAQmxReadDigitalLines referenced in function NI6008_DigitalInput NI_6281\NI6281.obj
  error LNK2019: unresolved external symbol DAQmxCreateDIChan referenced in function NI6008_DigitalInput NI_6281\NI6281.obj
  error LNK2019: unresolved external symbol DAQmxWriteDigitalLines referenced in function NI6008_DigitalOutput NI_6281\NI6281.obj
  error LNK2019: unresolved external symbol DAQmxCreateDOChan referenced in function NI6008_DigitalOutput NI_6281\NI6281.obj

  These, of course, are the functions OR that I use.  The NIDAQmx.lib has been added to the Input of the link property.

  Any help would be appreciated.

  Thank you

  -Neil shore

  Hi LaserShore,

  Think you that you added the 64-bit platform settings target according to this page? : http://zone.ni.com/reference/en-XX/help/372636F-01/mstudiowebhelp/html/64bitcore/

  Already running 32-bit application? Have you changed references to the 64-bit version?

  You use Measurement Studio? If so some features are not supported with 64 bit.

  Also when you say that you have added the NIDAQmx.lib, did you follow this KB:http://digital.ni.com/public.nsf/allkb/38F67B28D995C6958625706E000C580C

• MAX does not recognize NOR-DAQ traditional (old) devices * HELP

  I have a card PCIe-6259.  I want to use blocks of input-output in my program .vi (read Port DIO-DIO Port writing reading Digital Line), so I installed the version of NOR-DAQ traditional (old) devices 7.4.4.   But when I got to MAX (measures & Automation) and look on the left side under devices and Interfaces, I do not see the Tradional-NOR-DAQ tab; I see only the devices NOR-DAQ-mx, PXI, series and parallel system.

  Then when I go to run my program I get the error: error-10401 took place in a DIO Port Config Possible reason (s): NOR-DAQ LV: the specified device is not a product of National Instruments, the driver does not support the device (for example, the pilot exited until the device has been supported), or the device has not been configured using the Explorer Measurement & Automation.

  So, how do MAX to recognize that I have installed NOR-DAQ traditional (old) 7.4.4?

  Thanks for the reply!  I realized this too after going through the files for example... but thanks for the confirmation.

• Global variables are accessible from the local computer

  While he was trying to use RT project, I can deploy the file to the RT target and communicate with the host using a shared variable.

  But the host VI file returns an error stating that the shared in the pattern-block VI host variable is illegal.

  (RT.lvib\Link reqd\ 'shared variable' node is illegal)

  It also gives a description mentioning that global variables are accessible only to local machines.

  What is the cure?

  Hi Shan21,

  I think your problem with communication between the aim of RT and the host PC might be caused by how your deployment of your variables. Please take a look at the following and let me know what you think,

  Kind regards

  ******************************************************************************************************************************************

  When you make the executable of a project using shared variables, you must have a local copy of the variables on the deployment computer that are then linked to the 'real' shared variables stored on the target - cRIO, in this case.

  This means that the display of your project should look like this:

  

  Note: Two libraries, which can have variables with the same name because they aren't both on the local computer.

  The steps required are:

  1. create variables shared in the normal Manor on the cRIO:

  

  a. right click on the target
  b. new > Variable
  c. properties of the variables enter the name (stop); Data type (Boolean) and the Variable type (always in network-published).

  2. create variables shared on the host PC:
  a. follow the steps 1 a - c
  b. right click on the box to enable anti-aliasing

  

  c. linking to the URL of the PSP, click on Browse - and select variable on the target:

  

  d. click Ok.

  Note: Remember also to deploy the shared manually variable llb. See the related links for more information.

  It's from a base of knowledge to write soon.

  Note:3UCBHM8T knowledge base: how to deploy network Variables shared a compiled executable

• I have 9, 1 pages in PDF files that are accessible and the need to combine them into 1 PDF file.  I tried adding, adding and the combine process of PDF files. The file created does not take my changes. The file created is partially accessible, but I have

  I have 9, 1 pages in PDF files that are accessible and the need to combine them into 1 PDF file.  I tried adding, adding and the combine process of PDF files. The file created does not take my changes. The file created is partially accessible, but I have to re - the problems that I had fixed in the unique files. I need suggestions on what else can be done, if any. Using Acrobat pro XI.

  By habit, I tend to combine PDF files in the Page pane by right-clicking thumbnails then 'Insert of Pages'-> 'From File'. For me, this preserves the tags of these two documents, although the tags may have to be moved to the correct location (if I remember correctly the tags for inserted pages are put at the end of the tag structure, regardless of where the pages are inserted), if I put the tags in the document to insert into a container as a Section tag It makes the process easier. Travel set of tags in the right place is the only re-fixing that I remember having to do. What behavior you encounter?

  a 'C' student

• How to find out what the police are actually using Firefox?

  How to find out what the police are actually using Firefox?
  Inspect the element don't say what substitute fonts.

  Firefox 24 ESR has the tab fonts in the Inspector, which shouldn't be a problem.

  • https://developer.Mozilla.org/Tools/Page_Inspector

• cannot screenshots of trash says that they are in use

  I took a bunch of screenshots to the practice and now I want their trash my desktop, but when I try it tells me they are in use. I already have them removed from the Recycle Bin on desktop, re-opened one by one and closed glimpse each time but not luck.

  Trash the screenshots.

  Restart the computer.

  Empty the trash.

• My wife and I bought hundreds of iTunes movies and music over the years. I have a terminal illness and won't last long. The account is in my name. How can I ensure that films and the songs that she and I have paid for are accessible for her after I spend

  My wife and I bought hundreds of iTunes movies and music over the years. I have a terminal illness and won't last long. The account is in my name. How can I ensure that films and the songs that she and I have paid for are accessible for her after I die?

  She needs to have your Apple ID and password. Your iCloud ID and the password if you have your own iOS device, so it can have access to these facilities. Even if she wanted to sell, it would need this information to remove the lock of activation before the sale.

• Photos I uploaded and edited should not be found - where on earth could they "hide"? Other photos I uploaded after are accessible.

  I can't find a few pictures that I have uploaded and published on iPhoto. Where can they be "hiding"? Other photos I uploaded after are accessible. Also, they are not on the back to the top of the My Book for Mac either.

  Re-read your question and consider how someone could help

  We cannot see you and have no idea what you have or fact

  Which versions of OS and software you have - you posted the pictures to the forum of Mac and state that you have iPhoto for Mac.

  LN

• External hard drive: cannot empty trash, because certain elements are in use

  Hello!

  MacBook Pro 13 "2014 retina

  El Capitan 10.11.2

  I have a 1 TB external hard drive. It is to Transcend.

  I found a useless file and I wanted to remove it. OK, all the files are removed but some records are not.

  There are 8 or 10 empty folders, and they are in the trash. So, when I press Cmd + shift + delete OS said these items are in use.

  How can I get rid of them?

  Reboot, re-login has not helped.

  What size is the drive you want to remove from formatted in?

  Select the drive and do a CMD + i to get info

  If the drive doesn't appear on the office not activate it from the Finder > Preferences to show