CUCM web gui

Similar Questions

• The proSafe (JGS524E + GS116E) Switches: Configuration Management Web GUI in VLAN specific

  Hello

  I use a JGS524E and a GS116E. The two are connected via a 802. 1 q uplink with all defined VLANS in him.

  A 802. 1 q other interfaces goes to a pfsense firewall, which serves as a router and dhcp server for each VLAN that I use.

  How can I configure the switches plug are in one VLAN specific and get his IP address of the dhcp server in this VLAN?

  At present, it seems to be random access: it is not predictable that range from intellectual property, it takes its IP configuration via dhcp...

  How management function works internally?

  Thank you

  Markus

  Hello

  Thank you. I tried it out, but the behavior seems to be a little different:

  I configured a static IP address for the switch (10.1.0.13 / 24). I have access to the switch web gui via the ip address of the host of a host directly connected (connected via a trunk port, where I put 1 VLAN on the trunk), but it is all the same, what VLAN that I use:

  When it is connected to the VLAN 1 I have access, but also through 10 VLANS, VLAN 20 and so forth (assumed, I configure my computer appropriate staticly in the IP network, for example 10.1.0.20 / 24). So it seems not be limited only to the VLAN 1. You have access to each vlan, only the IP configuration must be in the same network.

  I'm not sure, how it behaves when cascading the two switches, I have not tried.

  If this information can be useful for other users with the same question about this switching product line.

  For me, this behavior is not very well implemented from my point of view. For security reasons, you must limit access to the administration, for example by allowing access from a specific hardware port or a vlan. With the effective implementation, centralized management for a cascade topology is not easy to set up, perhaps because the behavior is not very clear and not documented in the manuals.

  Mentioned on the edge: there is no available TLS/SSL encryption when accessing the web gui (not https). So the password is transmitted in clear text... not a very good idea, I think.

  Thanks a lot for your help.

  Best regards

  markusd112

• Reset the Web GUI on the M600 iDRAC

  Hello

  I have problems of access to the iDRAC web gui on a couple of blades M600 (needed to get the console and re - install the operating system).

  I read on Google that racadm racreset running can solve the problem, but this seems to be only available on of m610?

  When I ssh into the M600 blade I gives me a prompt SMASH CLP Console (v1.08) and can not find everything related to actually reset the interface itself idrac.

  Is it still possible on a M600?  Otherwise, how can we reset the iDRAC interface?  It does not fundamentally on port 80 - unlike our other blades, also M600s.

  Thank you very much in advance for any pointers or direction.

  Thank you

  SoC

  Rob,

  An option to rest iDRAC on M600 is with the CMC. You can connect to the CMC and perform iDRAC reset page "Overview-> troubleshooting-> Reset chassis components. Select iDRAC reset for the corresponding housing option. You can also do CMC Racadm. Run "racadm racreset m - Server -" of SSH or using remote racadm and CMC IP.

  What iDRAC firmware you have on M600? 1.65 is the last FW for iDRAC M600. If you do not have this FW on iDRAC can you update and check the same. You can download the same from

  www.Dell.com/.../PowerEdge-M600

• Force10 S60 - activation Web GUI

  Does anyone know how to activate/access web GUI on a Force10 S60?  I have the switch set to the point that I can ping from a client, but I can't seem to get access from a web browser.  The help files have not gave me so much about the issue, so I hope someone here can point me in the right direction.

  Thanks in advance,

  -Michael

  Hi Michael,

  There is not an on the S60 web management interface, it's only of CLI. The commands that worked for the S50 aren't in the configuration for the S60 guide. http://downloads.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_networking/esuprt_net_fxd_prt_swtchs/Force10-s60_Reference%20Guide5_en-us.PDF

  http://downloads.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_networking/esuprt_net_fxd_prt_swtchs/Force10-s60_Reference%20Guide6_en-us.PDF

• Cannot access the ISE-3395-K9 CISCO Web GUI

  Hello

  I can't access the ISE-3395-K9 web gui interface concert 0 with ip address is 192.168.1.10.  I put the ip address of my labtop to 192.168.1.20 and could ping back but am still not able to access them through a direct connection between my labtop to concert interface 0 using one of the supported web browsers.  Any help would be greatly appreciated.

  It is possible that the GUI was configured to restrict access to only certain IPs / subnets. If 192.168.1.x isn't one of them, then you will have access.

  Are you able to connect to the shell via SSH? If so, you should check and confirm that all associated ISE services run by running the following command:

  show the application status ise

  Thank you for evaluating useful messages!

• Cisco 4400 WLC - access web GUI remotely

  I know how to access the graphical interface from the service port. However, I am not able to access the site of Port 0. IPs have all been set correctly. We have a management VLAN in our company. I have configured the management interface of WLC for an ip address from that subnet. Port 0 is connected to a switch of 3560 G. I put the switch port to a port of access to the management of VLANs and I tried to make the switch as a trunk port, with the vlan native on the vlan management. I'm not able to ping, or access the web GUI remotely through the management VLAN. Is it normal?

  Jeff

  Hi Jeff,

  Please try to set 0 as vlan on interface of management on WLC after configuration of vlan native on the switch. If you have not yet tried.

  order - management configuration interface vlan 0

  Note - You must children all wlan r mapped with management interface before any change in CLI.

  hope this will solve your prob.

  Thank you

• vCenter 6 web gui - host isolation response

  Hello

  I was looking at the option of isolation of host and then noticed that he not there no "leave it on" option on vcenter 6 web gui (version 6.0.0 2656761). However, "leave it on" option is still available on the client. As you can see from the screenshots, I chose the option "leave on" on the heavy and used customer "turn off and restart the virtual machines ' option on web gui.

  I really appreciate if someone provides the details to clarify my confusion because I'm not sure what settings will apply in case of isolation of the host.

  
  

  Thank you

  AFAIK the "leave it powered on" in c# client is now called as "Disabled" in the Web Client, which means nothing do, don't react not if the host gets isolated.

  You say that you set the value "leave powered we" in c# client and then when you check the settings for the cluster in the Web Client, it displays "Power Off and restart VM?

  If so, no refreshing or reconnect to the web client result by displaying "Disabled" in the web client?

  I hope this helps.

• vRA 6.2 - Business Group exists in the vRA Web GUI, is not listed by the vCAC Plugin in vRO

  I have this strange situation, where a business group is displayed in the Web GUI, I can modify its permissions, VMs, etc, the list is fully functional. Also, when I choose a computer virtual set up by a member of this group in the vRealize Orchestrator vCAC Plugin, I get the appropriate parent (Organization) displayed.

  However, the Group of companies is not displayed in the plugin under vCloud automation Center--> hostname--> Administration--> business groups, I also tried earlier with Server.findAllForType ("vCACCAFE:BusinessGroup"), without success.

  Someone in the face of the question before?

  Had to reinstall plugins vCAC vRO, charging only for them did not help.

• 'New user' button missing in web GUI?

  ReadyNas 2120 v2

  I note in the manual of the OS6, new button shows, but when I browse the web portal is missing. LDAP is set up then maybe disappears it button?

  Tripline wrote:

  LDAP is set up then maybe disappears it button?

  I think it's true (users come from AD, in this case).

• Incorrect display of Port settings of the WEB GUI - port-sx300_fw 14088 SG300 - 28 p management

  Running V02 SG300 - 28 p in Layer 3 Mode.

  I have upgraded to the latest firmware and bootloader. I noticed that my ports management screen not display correctly.  It displays any of the table and it looks like a few places at the top without (almost empty) text.

  There is also a window Edit to Port VLAN that does not display a usable screen - no text and a few radio buttons.

  Someone has an idea of what I can do to fix this?  MD5 hash on my download games so I think not only its corrupt, more it flashed just fine on the switch.

  -Edit - the security setting has not set the pobrlem (forgot to return to the 1.4.0.88 fw)

  Here are the two screens that still have questions:

  SG300 - 1.4.0.88 - problem - 1.jpg

  

  SG300 - 1.4.0.88 - problem - 2.jpg

  

  Hi Robert,.

  I think that this message can help:

  https://supportforums.Cisco.com/discussion/12358601/SG200-50p-Web-interf...

  Kind regards

  Aleksandra

• No connection with Aironet 1602i on only web gui

  Can someone tell me if there is no magic required to get the standalone Aironet 1602i (AIR-SAP-1602I-E-K9) react on its web interface?  The device appears when connected to the Netgear M4100 switch - 26G - PoE (), flashing green LED, then I think "chirp" (green on 1 second, off the coast of 3 seconds) which is how it should be.  I see in the firewall, it took an IP address, but although it meets the pings there is no connection on the interface web, just "cannot establish connection."

  Any help much appreciated.

  You can return the device for an AIR SAP1602 or convert the AP... Here are some links that you can follow and a YouTube video.

  By using a TFTP server to revert to a previous version

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp160918

  https://supportforums.Cisco.com/docs/doc-18268

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp160918

  http://www.YouTube.com/watch?v=QQ_NuxdRhQ4

  https://supportforums.Cisco.com/docs/doc-14960

  Thank you

  Scott

  Help others by using the rating system and marking answers questions as 'response '.

• Connection Error 1120 ACS cisco acs 5.0 web gui

  Hi all

  I installed the unit acs 1120 as follows

  entered in the installation in console mode command

  aiinstalle licensevia gui mode

  But when I access the gui mode it disconnect regularly

  When I ping ping is successful and shows life 128

  but after some time, the connection is estabalished and when I ping the TTL shows 64

  can someone help with this problem

  Thank you very much

  Hello

  I couldn't quite follow the description of your problem. Can clarify you the problem more in detail.

  You then mention access to the ACS GUI mode it to disconnect regularly. You lose any IP to GBA connectivity, or is the problem only through the user interface?

  Please can you include ACS cli:

  view the status of the acs application
  See the version

  Show tech

  Would also be relevant to see the output of 'display the acs application state"when the problem occurs.

  Additional troubleshooting, the support beam will also relevant information during problem occurrence timestamp. You need to enable the debug logs, for ex:

  GBA cli:
  admin #conf t
  exploitation forest admin (config) # loglevel 7
  exit admin (config) #.
  # acs admin - config
  After a few seconds,.
  You can then log in with the credentials of user/password for GUI of the CSA name.

  acsadmin(config-ACS) # debug level mgmt-acsview of-journal of debugging

  acsadmin(config-ACS) # debug level to debug-log duration
  output acsadmin(config-ACS) #.

  Following the appearance of the problem, the support beam then downloadable GUI Monitoring & Report Viewer > troubleshooting > ACS support Bundle.We will need to check on the timestamp of the problem newspapers.

  But for now, more details about the problem seem necessary as well as the output display orders of cli ACS mentioned above.

  Thank you

  Alex

• cannot connect to web gui (apache) but I can't get into obtool

  I have a 10.4.1 installation I used regularly for a long time. I'm connected even in yesterday afternoon to change a backup schedule.

  This morning, I can log into the apache/web site. I get my password and it returns me to the login screen. I know I'm in the correct password, because if I get the wrong password... it tells me that my connection is incorrect. Yet, when I enter the correct password... it just returns me to the sign again. I don't have any errors in apache error logs and no errors in the logs for ssl access. The connection process also creates the sess_ file in /tmp/ then... I am at a loss to understand why. I restarted the service several times and have even restarted the server. OEL5 5 update

  Any help would be appreciated. Thank you

  He end up being that the

  point mounting/usr/tmp was not always full.

• Using every night (64). Could not find a way to 'save' the cookies options settings in the Web GUI. Something I'm missing?

  I want to use the option "use the custom settings for history" with cookies turned on in the view of privacy in 35.0a1 every night (2014-09-07). But there is no way that I can save the changes, nightly switch to normative action "remember history" automatically.

  Anyone?

  Maybe you should install the current version of Firefox or switch on the beta update channel instead.

  If you have installed at night because it's the only version that has a 64-bit version, so keep in mind that 64-bit Nightly builds for Windows are generated only for test compilation errors and are not all tests that get any other builds, so the risk that something is wrong can be very high.

  32-bit versions of Firefox should work without problems on 64 bit versions of Windows.

  You can find the full version of the current Firefox 33.0.1 version in all languages and for all systems operating here:

  • https://www.Mozilla.org/en-us/Firefox/all/

  The latest beta version can be found here:

  • https://www.Mozilla.org/en-us/Firefox/beta/all/

• SRW2024 no web gui

  We have a brand new SRW2024 v1.3. It came with firmware 1.2.2b on it. I can get the login screen, but after authentication, I don't see any info. I get the frame html information, but the image pages are not displayed. I tried on 2 different computers with Firefox 3.5, Google Chrome and IE 8. I found a reference to passing the user name "admin", but that did not help. I tried to add as 2 other user name, but one of those who worked or the other.

  The connection of the console works fine. That's what I used to try to re - charge the same firmware. I don't think I can use the firmware 1.2.2 and 1.2.2b is the last available from cisco.com.

  I can't understand why it would not work. We have more than 3 of them on another site, but I don't have access to those that until next week. Is there anything else I can try?

  Aaron

  Read this:

  https://supportforums.Cisco.com/message/3103397#3103397
  https://supportforums.Cisco.com/message/3103923#3103923
  https://supportforums.Cisco.com/message/3103511#3103511