delay value

Similar Questions

• Triggers of analog input output meter with delay

  Hello!

  I am currently using a PCI-6251 DAQ card with a block of connection BNC-2120.  I have a VI (one that is attached to this topic) that will essentially be an analog input signal and produce digital impulses from the output of the meter to each instant trigger.  I am also able to define a series of delay values such that the delay will update automatically each at intervals specified by the user or when you press the stop button.  I wonder if there is anyway to change this program as the time-out value will change every instant release.  So, for example, in the first trigger a pulse is produced 0 second delay, then immediately when the next instant relaxation is reached, a push will occur with a 0.1 second delay, etc...  And I want that the series of the time-out values to keep looping.  I tried to use my current VI, with time to stop at each iteration to be less than half of the period, so theoretically it should go to the next delay value in the next instant trigger.  Then I tried to put a certain time-loop around it to keep the job going, but it doesn't seem to work.  I've attached a screenshot of my attempt, please let me know if this is possible, thank you!  To see what each part of the VI in the screenshot, please see the screws attached, thank you!

  P.S. for the VI that is attached, the analog input signal is 281Hz, the pulse width is 2.5% of the period and the delay is in the stages of T/20.

  

  No worries,

  Please see the attached block diagram image.  It is important to wire terminal on the Read.VI DAQmx acquire in a constant to the number ofsamples.  This will force this function to wait until many samples are available in the buffer.  In my example, you will get 1000 samples per second (because my rate is 1 kHz).  and these 1000 were submitted directly to the FFT.  What happened for example of you, it is only because you have not specified the number of samples to read, it is by default (-1), which means that the DAQmx Read.vi will pull all the data that is available in the buffer at the time.  So if you had only 2 samples in the buffer that your FFT will have only two samples on average and as a result it will fail. Try this and it should help!

  

• Equium P300-16 t with Synaptics touchpad. Stuck left button?

  Hi all

  I have an Equium P300-16 t with a Synaptics touchpad.
  A few months back I had the following problem. As soon as I touch the touchpad or the left/right button, the icon will appear to show the button on the left as being depressed; It would be nice up to this point. I've updated the drivers, tried a system restore, checked under the button of touchpad for obstruction etc and nothing has changed.
  I made a completely new reinstall of Windows... still the same problem. Suspected a defective touchpad, so I contacted Topaz for a replacement touchpad mounted that and still the same problem.

  so... after having eliminated defective drivers/software/hardware, I'm out of ideas. Is there anything else I can check?

  Works very well with a USB mouse.

  Thank you

  James

  > As soon as I touch the touchpad or the left/right button, the icon will appear to show the button on the left as being depressed; It would be nice up to this point

  I think you should check the settings.
  In Control Panel-> mouse-> last (Advanced) tab-> the Advanced Settings button

  Here, you should be able to get all the parameters of the touchpad.
  In my case, I found interesting feature in the speed of the pointer and typing parameters.

  There is a charming area of tape, and if you enable registration you could get access to other environments of tapping.
  The option is called DragLock in my case that his automatic release and auto release delay value is set on the court.
  Recommend you check this!

• Change of the dynamic Cycle for PWM

  Hello people of LabView warned there!
  I'm doing PWM for the servo using LabView.
  I was able to manually move my servo with this: http://www.ni.com/white-paper/2991/en

  My goal is to automate the position of the servo as a movement of sinuisoidal and to do,

  I need to automate the cycle to oscillate in 5% ~ 10% automatically over time.
  I looked into stuff like:

  http://forums.NI.com/T5/counter-timer/PCI-6602-PWM-generation-dynamic-sine-duty-cycle/TD-p/1522442

  But it was not too helpful, that I was getting too error-200301.

  I want to be able to move the position of the servo to ~ 10 Hz, if it's important and the FREQ square to wave the

  servo signal (PWM) must be 50 Hz.

  Any help? Thank you!

  ____________________________________
  Attached, that's what I'm trying to do. The sinusoidal movement of the servo is (supposed to be) really pair upwards with

  a counsel of the BNC-2120 of the analog output. The part of the servo control is separated on the upper part.

  The error occurs on the first iteration of the loop? What is the initial delay value on? If the initial delay is greater than the length of the loop, you can still get this error.

  This is important if you use a (ms) waiting rather than wait for the next "millisecond" several?

  And checking against the local variable duty cycle is still useless. You should check against the previous cycle which was set, not the local variable cycle duty.

• SPA3102 CID has not managed to asterisk

  Hello

  I have several 3102 to FXO line with asterisk integration.

  The only thing that I was unable to make it work, even with the option:

  PSTN to VoIP CID CID: Yes

  Was to the CID go to the asterisk, if I check the info on 3102 tab, in last PSTN Caller:, I can see the last number of the caller.

  I have what would be missing?

  Thanks in advance,
  Jorge Bastos,

  It seems that "yours" RTC gives CID information between the first and second ring. Currently, PROMPTS for Asterisk is sent immediately, for example before the CID is known. It must be delayed until the CID is available.

  Go to the section "FXO Timer values".

  The "PSTN Answer Delay" value number (in seconds) which is a little more than sound period on your PSTN line. Period of ring is about 5 second in most countries. so, I recommend that you use 7 seconds here in this case.

• Counting of days in a range a group

  I use Oracle 11.1, and I have the table and the following data.

  CREATE TABLE DELAYS
  (
     DELAY_ID     NUMBER (5) NOT NULL,
     CASE_ID      NUMBER (9) NOT NULL,
     TYPE_ID      NUMBER (2) NOT NULL,
     START_DATE   DATE NOT NULL,
     END_DATE     DATE
  );
  
  ALTER TABLE DELAYS ADD (PRIMARY KEY (DELAY_ID, CASE_ID, TYPE_ID));
  
  INSERT INTO DELAYS VALUES (1, 3770, 1, DATE '2014-08-01', DATE '2014-08-02');
  --INSERT INTO DELAYS VALUES (2, 3770, 1, DATE '2014-08-02', DATE '2014-08-02');
  --INSERT INTO DELAYS VALUES (3, 3770, 2, DATE '2014-07-01', DATE '2014-07-10');
  --INSERT INTO DELAYS VALUES ( 4, 3770, 5, DATE '2014-7-1'  , DATE '2014-7-10' );
  --INSERT INTO DELAYS VALUES ( 5, 5430, 2, DATE '2014-8-5'  , DATE '2014-8-5'  );
  --INSERT INTO DELAYS VALUES ( 6,    1, 2, DATE '2014-8-1'  , DATE '2014-8-5'  );
  --INSERT INTO DELAYS VALUES ( 7,    2, 2, DATE '2014-8-1'  , DATE '2014-9-1'  );
  --INSERT INTO DELAYS VALUES ( 8,    3, 2, DATE '2014-1-1'  , DATE '2014-8-5'  );
  --INSERT INTO DELAYS VALUES ( 9,    4, 2, DATE '2014-8-1'  , DATE '2014-8-5'  );
  --INSERT INTO DELAYS VALUES (10,    5, 2, DATE '2014-7-1'  , DATE '2014-8-5'  );
  
  COMMIT;
  

  I need to return the number of days of delays (end_date - START_DATE + 1), grouped by the CASE_ID and TYPE_ID.

  Since I have to make sure that the days are not counted several times, I'm expanding including date between start_date and end_date on the lines of the dates using the form:

      SELECT D.CASE_ID, D.TYPE_ID, D.START_DATE + LEVEL - 1 DELAY_DAYS
        FROM DELAYS D
  CONNECT BY LEVEL <= (D.END_DATE - D.START_DATE + 1);
  

  The following query returns the number of days of delay for each line (every day of delay are in the expression of slider for verification).

  But I can't group this request by CASE_ID and TYPE_ID and aggregate the days of delay to remove duplicates.

  If I SUMMARY the COUNT_DELAY_DAYS, then duplicate days are counted more than once.

  SELECT D.*,
         CURSOR ( (    SELECT (D.START_DATE + LEVEL - 1)
                         FROM DUAL
                   CONNECT BY LEVEL <= (D.END_DATE - D.START_DATE + 1)))
            DELAY_DAYS,
         (    SELECT COUNT (D.START_DATE + LEVEL - 1)
                FROM DUAL
          CONNECT BY LEVEL <= (D.END_DATE - D.START_DATE + 1))
            COUNT_DELAY_DAYS
    FROM DELAYS D;
  

  I tried to use this query to the group by the CASE_ID and the TYPE_ID and count the days of delay, but the numbers are bad, from the second row of data is added to the table.

      SELECT CASE_ID, TYPE_ID, COUNT (D.START_DATE + LEVEL - 1) COUNT_DELAY_DAYS
        FROM DELAYS D
  CONNECT BY LEVEL <= (D.END_DATE - D.START_DATE + 1)
  GROUP BY CASE_ID, TYPE_ID;
  

  If I change the NUMBER to be COUNT (DISTINCT...), then I get the exact number of days of delay, grouped by the CASE_ID and TYPE_ID, but performance suffers, as most lines of data are added to the table.

  This should be good for thousands of CASES and TYPES that cover the delays of days, weeks, months, or even years.

  And several users need to be able to run it at the same time if that makes a difference.

  Use change beginning of Group-method to combine the intervals overlapping / adjacent:

  with t1 as)

  Select case_id,

  TYPE_ID,

  start_date,

  End_date,

  case sign)

  start_date - max (end_date) more)

  case_id partition,

  TYPE_ID

  order of start_date,

  End_date

  rows between unbounded preceding

  and 1 preceding

  )

  )

  When 1 then 1

  0 otherwise

  end start_of_group

  delays

  ),

  T2 as)

  Select case_id,

  TYPE_ID,

  start_date,

  End_date,

  Sum (start_of_group) more)

  case_id partition,

  TYPE_ID

  order of start_date,

  End_date

  ) grp

  from t1

  ),

  T3 like)

  Select case_id,

  TYPE_ID,

  Max (end_date) - min (start_date) + 1 grp_delay_days

  the t2

  Case_id group,

  TYPE_ID,

  GRP

  )

  Select case_id,

  TYPE_ID,

  Sum (grp_delay_days) delay_days

  T3

  Case_id group,

  TYPE_ID

  order of case_id,

  TYPE_ID

  /

  SY.

• How can I access a variable on the main timeline of a movie nested in HTML5 Canvas

  Hello

  This should be pretty simple, but for some reason, it does not work if I have the wrong syntax.

  But I have a movie clip with a bit of code in it.

  It is a timer.

  I want to be able to program the wait time: since the main scenario and that the timer read this variable on the main timeline.

  I implemented the delay var = 1000 on the main timeline, but then I do not seem able or knows how to get this variable in my code in the nested MC. It is quite difficult to find the reference of the paradigm flash timelines on H5 support pages, so I really appreciate the help.

  tl2 var = this;

  TL2. Stop();

  var delay = delayMain;

  var startTime is createjs. Ticker.getTime ();

  createjs. Ticker.addEventListener ("tick", f);

  {function equation

  If (createjs. Ticker.getTime () - startTime > delay) {}

  TL2. Play();

  createjs. Ticker.removeEventListener ("tick", f);

  }

  }

  If you want to get to a variable defined by a feature any at any depth, you can use the window. As:

  Window.Delay = value;

  in a deeply buried movieclip, can be read in any other level of the project.

• Automatically start vCenter and vms

  Hello

  We have Windows Server 2008 R2 running vCenter 4.1 connected to host computers running ESXi 4.0 Update 1.  Every time we restart the server, the vmware vCenter and vmware vCenter Webservices services start up, they are set to start.  They need to be on the delayed start?  I check the event logs to see what is happening.  Is there a log of vmware that I could look at?

  In addition, we want to implement our virtual machines as the domain controller starts automatically, but I can't find a way to do.

  Thank you

  Mike

  Thank you very much, we are using SQL Express despite 2 virtual machines running SQL Server 2008 :-)  I'm going to the delay value and see.

  If it does not help there are some registry entries, you can make

  http://KB.VMware.com/kb/1007669

  In addition, we vSphere Essentials.  How can I know that if it is configured for high availability and where I see these priorities?

  Essentials does not come with HA.  You can configure your options of start/stop for your guests by going to the configuration of the host tab: start/stop of the VM - properties (upper right corner)

• random timer interval

  I'm currently building a scene in which multiple instances of the same mc start at different intervals and continue to reboot over and over again at different intervals.  I try to get the mc from anywhere from 3 to 10 seconds after that it has finally stopped.  I used this code as3 inside mc th himself.

  var randNum:Number;

  randNum = Math.round (Math.random () * 5 + 2 * 1000);

  trace (randNum);

  var: timer = new Timer (randNum);

  timer.addEventListener (TimerEvent.TIMER, randGen);

  function randGen(e:TimerEvent):void {}

  trace ("Hello");

  }

  Timer.Start ();

  The trace shows a random number is generated, but it does not appear after the first run because the interval of the timer.  "Hello" appears in the output window every second after the randNum is awarded regardless of the value of the randNum.

  I tried to use timer.reset, but which seems to do nothing at all or stops the repeat.  Probably because I don't understand how to use ".reset" or ".delay".  I have them looked in the documentation and still don't get how they are used or even if they are suitable for this situation.  Obviously, a lot I don't understand about as3.  Will someone kindly point out what I'm doing wrong?  Thank you.

  If you are insisting on the use of the way you have set it up, maybe you can try to do something like this:

  var randNum:Number;

  randNum = Math.round (Math.random () * 5 + 2000);

  trace (randNum);

  var: timer = new Timer (randNum);

  timer.addEventListener (TimerEvent.TIMER, randGen);

  function randGen(e:TimerEvent):void {}

  var timerObj:Timer = e.target as timer;

  randNum = Math.round (Math.random () * 5 + 2000);

  trace ("New delay value:", randNum);

  trace ("Hello");

  timerObj.delay = randNum;

  }

  Timer.Start ();

  Like the previous poster mentioned if you want that a more graduated random delay to pay attention to what you use for the random number. Math.Random () generates a floating point number between 0 and 1 (for example: 0.65687651151), so Math.Random () * 5 is going to be a part of the whole number of 5. Addition of 2000 that will only give a number between 2000 and 2005.

  Hope that helps!

• Why is relativeInitalX value not taking into account the triggering delay? using scope OR with the PXI-5124

  Hi all

  play with a digitizer PXI-5124 in a case of PXI1042Q with a PXI8110 controller that runs labview 2012 (latest updates) with the latest version of the driver NIScope.

  I put in place an acquisition of off-delay (by assigning the triggering delay, for example 20us) which works very well (I can tell by the signal I get delay control works correctly), but the data returned in the info wfm cluster (using the 2D version of niScope I16 Fetch) does not have this delay.

  Description of the relativeInitialX within this cluster indicator indicates "is the time in seconds between the trigger and the first sample in the acquired waveform" but its never to return something around 1E-9 independent of trigger delay. Surely the relative initial x should reflect the triggering delay?

  I'm doing something wrong?

  Thanks for your help!

  So, I made a screenshot of the image in the section "Trigger Delay" link I sent you.

  

  Meaning of the symbol:

  T0 = original moment of relaxation

  T1 = time to trigger used in the acquired record (t1 = t0 + TriggerDelay)

  T2 = time of first sample in the record of the acquis.

  RX = relativeInitialX = t1 - t2

  Response to previous reviews

  «I understand what you're saying - so basically, if I want to know the delay of my trigger for the first sample in the record, I just add my delay time value to the relativeInitialX.»

  • Close, the delay of the original trigger (t0), for the first sample in the record (t2), would actually be TriggerDelay-relativeInitialX

  «.. . Nowhere does graphically describe where is the relative value of initialX real. »

  • Right, relativeInitialX is not a timestamp, so it is not a place on the timeline, it is the difference between two timestamps (t1 and t2 above), where the relativeInitialX name.

   

  "The trigger"record"is the straight line in the Middle, so expect relative to - 1/2 initialX record length?

  • Almost correct, because the reference trigger is relativeInitialX to the position of 50%, will be the time in seconds for 1/2 the record length. (i.e. If the registration has been long relativeInitialX, 2s = 1 s).  RelativeInitialX will always be the delta time between the trigger (t1) and the first sample returned in the record (t2).
  
  
  • For example using the picture above: If t0 is 10 sec, Trigger Delay = 3 sec, SampleRate = 1 kHz, = 1000 record size.  This means that t1 = 13 s.  Our record is long of 1s (1000 points to 1 DC between each = 1 s), if t2 = 12.5 sec.  If away from all these moments are absolute time, as the timestamps.  So relativeInitialX = t1 - t2 is 13-12, 5 = 0.5 sec.
  
  
  • As a side note, the reference position should not be 50%, you can configure to between 0-100%.

  Time not yet discussed record attributes

  I don't want to make you more confused, but there is another useful attribute in the waveform info that we've not yet discussed and its AbsoluteInitialX.  Starting from the NOR-SCOPE help file:"absoluteInitialX is the timestamp of the first sample of recoveries in seconds..." "So, using the above image, absoluteInitialX = t2.

  I hope this helps.  If a part is still not clear, let me know.

  -Nathan

• to fill the gaps with value of lead and the delay and make average and the gap between earned

  Thanks in advance
  
  I have table as below

  ID          TYPE     NUM     NAME     BEG_MP     END_MP     VALUE
  10001103N     3     1190001     WST     0.000     0.220     
  10001103N     3     1190002     WST     0.220     0.440     
  10001103N     3     1190003     WST     0.440     0.820     12800
  10001103N     3     1190003     WST     0.820     1.180     12800
  10001103N     3     1190004     WST     1.180     1.220     
  10001103N     3     1190004     WST     1.220     1.300     
  10001103N     3     1190005     WST     1.300     1.420     14800
  10001103N     3     1190005     WST     1.420     1.550     14800
  10001103N     3     1190006     WST     1.550     2.030     
  10001103N     3     1190006     WST     2.030     2.660     
  10001103N     3     1190007     WST     2.660     2.780     

  What I need is to fill the gaps with value of lead and the delay and make average and the gap between the values
  

  ID          TYPE     NUM     NAME     BEG_MP     END_MP     VALUE
  10001103N     3     1190001     WST     0.000     0.220     12800 ---> Lag value
  10001103N     3     1190002     WST     0.220     0.440     12800 ---> Lag Value
  10001103N     3     1190003     WST     0.440     0.820     12800
  10001103N     3     1190003     WST     0.820     1.180     12800
  10001103N     3     1190004     WST     1.180     1.220     13800 ---> Avg(12800,14800)
  10001103N     3     1190004     WST     1.220     1.300     13800 ---> Avg(12800,14800)
  10001103N     3     1190005     WST     1.300     1.420     14800
  10001103N     3     1190005     WST     1.420     1.550     14800
  10001103N     3     1190006     WST     1.550     2.030     14800 ---> Lead Value
  10001103N     3     1190006     WST     2.030     2.660     14800 ---> Lead Value
  10001103N     3     1190007     WST     2.660     2.780     14800 ---> Lead Value

  create table AVG_TABLE
  (
    ID     VARCHAR2(20),
    TYPE   NUMBER,
    NUM    NUMBER,
    NAME   VARCHAR2(10),
    VALUE  NUMBER,
    BEG_MP NUMBER(6,3),
    END_MP NUMBER(6,3)
  )
  ;
  
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190001, 'WST', null, 0, .22);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190002, 'WST', null, .22, .44);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190003, 'WST', 12800, .44, .82);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190003, 'WST', 12800, .82, 1.18);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190004, 'WST', null, 1.18, 1.22);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190004, 'WST', null, 1.22, 1.3);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190005, 'WST', 14800, 1.3, 1.42);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190005, 'WST', 14800, 1.42, 1.55);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190006, 'WST', null, 1.55, 2.03);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190006, 'WST', null, 2.03, 2.66);
  insert into AVG_TABLE (ID, TYPE, NUM, NAME, VALUE, BEG_MP, END_MP)
  values ('10001103N', 3, 1190007, 'WST', null, 2.66, 2.78);
  commit;

  Hello

  Use LEAD and LAG when you know exactly how far is the target line (for example, if you know the desired value is on the next row).
  If you don't know exactly how far is the target line, then FIRST_VALUE and LAST_VALUE are more likely to be useful.

  WITH     got_neighbors     AS
  (
       SELECT     avg_table.*
       ,     LAST_VALUE (value IGNORE NULLS) OVER (ORDER BY beg_mp)          AS prev_value
       ,     LAST_VALUE (value IGNORE NULLS) OVER (ORDER BY beg_mp DESC)     AS next_value
       FROM     avg_table
  )
  SELECT       id, type, num, name, beg_mp, end_mp
  ,       COALESCE ( value
               , ( NVL (prev_value, next_value)
                 + NVL (next_value, prev_value)
                 ) / 2
               )     AS value
  FROM       got_neighbors
  ORDER BY  beg_mp to f
  ;
  

  Riedelme is correct: LAG LEAD (as well as FIRST_VALUE and LAST_VALUE) can return only the values that are there (or that you give as default values). This means that you can not solve this problem with these functions alone; you need something else (as NVL, above) to provide value when the function does not find it.

• Population Event.Value delay

  I have a few forms requiring barcodes for analysis.  In order to generate these bar codes, I create a text field using a 3sur9 font, set it read-only and the value of script:

  event.value = "*" + this.getField ("FIELDNAME") .value + "" * ";"

  Normally, it goes off without a hitch, but I'm having a problem with the way this FIELDNAME value where FIELDNAME is a scripted value.  For example, in one situation, FIELDNAME is a locked with a value by script text field:

  var A = this.getField("PART1").value;
  var B = this.getField("PART2").value;
  var C = this.getField("PART3").value;

  var strPart1 = String (A);
  var strPart2 = String (B);
  var strPart3 = A < 2? "0" + string (C): String (C); "
  var fullname = (strPart1 + strPart2 + strPart3);
  Event.Value = fullname;

  This is done because "PART1" is a mapped data field of 7 digits, "PART2" is a mapped data field of 2 digits and "Sect3" is a mapped 2-digit data field that often starts with a 0.  They must be concatenated to the bar code be correct, but there is no data for a fully concatenated value map.  The Field_Name field performs very well, but the barcode only outputs «*»  As soon as any other field in the form is filled manually, the bar code change to the appropriate "* FIELDNAME."

  I have no validation trigger anywhere in the form, but this seems to be an event validation that went wrong.

  Any ideas?

  Thanks in advance,

  A.

  I forgot to add, the problem is probably that the field calculation order is incorrect. To define it, go to the forms editing mode and

  then select "forms > edit > set field calculation order of fields.

• Follow-up of applications for security delays

  When you use the private mode on http://www.lensbest.de/ with activated protection of follow-up, most of the requests are delayed by 1 to 2 seconds. Loading animation is not present in this time interval. For example, the links in the menu and in the footer are affected by the problem.
  If I disable the protection followed in the address bar, the delay goes away.

  I found the problem in Firefox 42. Firefox to reset to the default values and creating a new profile didn't help.

  I can do something on the server to resolve this problem?

  h.Klaus said

  When you use the private mode on http://www.lensbest.de/ with activated protection of follow-up, most of the requests are delayed by 1 to 2 seconds. Loading animation is not present in this time interval. For example, the links in the menu and in the footer are affected by the problem.
  If I disable the protection followed in the address bar, the delay goes away.

  I found the problem in Firefox 42. Firefox to reset to the default values and creating a new profile didn't help.

  I can do something on the server to resolve this problem?

  Could be closed. The problem was caused by a Timeout of Google Tag Manager.

• Forget the button against the history value delete when closing Fire Fox

  I have FF value delete browsing history all whenever I close Fire Fox, which is common. In addition to the fact that there is a delay in the suppression of history until closed FF is the Forget button more in-depth than my current method of deleting the history. The history is also deleted by Norton Utilities, whenever I run optimization NAKED at least once a day?

  Your question looks like it's to ask if the Forget button is more thorough than the deletion of all close. I think it's just the latest is automatic and forget the button is for those who want to do it with Firefox always open. They do the same thing but even thoroughly.

• Pavilion dv6: Audio delayed 5-10 seoncds

  Hey! On May 19, almost a month, I came home from the store and turned my laptop back, to find the audio doesn't sound as high quality as usual. I went into control panel Audio Beats and clicked on 'Listening experience' to see if the Beats Audio has been disabled somehow and when you click on the control panel crashed. I googled this problem and found something that suggested the IDT Audio to uninstall and reinstall. So I did, and it took two or three restarts after the reinstallation of IDT Audio, audio has started working again and seemed normal.

  The next morning, I turned my laptop on and recived a message telling me that it was unable to connect to the Service Notification of system events, I googled the problem and tried almost all recommend people solution (that I am able to do at least, also I have not tried to reinstall my OS because I don't want to lose everything). I managed to do so stop giving me the error for about a week, after I found that I had a Linksicle driver and I then uninstalled, done a scan with the free version of Malwarebytes and it had to get rid of all the PUPPY and we found some things, but then a few days ago the modem in our House was to ruin , and as it does that I have reset my laptop and turn it on again, I got the error FEEL new. This happens about 50% of the time I turn on my laptop.

  A few days ago, I found the themes service is restarted to bring the Aero theme that fails to appear when I get this error, I'm not too bored it start without Aero theme.

  What upset me a lot, that's what this thread is on about. Since I started getting the error SENSE I also get an audio delay of about 5-10 seconds. For example, I open Windows Explorer and start clicking on the various files, and it won't play noise light click until the program was opened for about 10 seconds after I click on a folder. The trash, empty the noise is also approximately 10 seconds fine most of the time. Playing files in Windows Media Player also lasts longer, at least for the first file I play at the opening of the program. If I'm listening to a playlist the next song will begin without delay.

  If it was all that is going on I wouldn't bother me too much. I can deal with playing mp3s and late sound Windows Explorer take just a few seconds to start. But this problem is also on the videos. And because I spend a lot of time on my laptop I look at YouTube, it turns out to be very annoying. When I go to a video, it takes about five seconds to start, as opposed to start immediately, as it should. And if I leave a video not suspended for maybe more than 20 seconds, it will give me the YouTube loading circle for about five seconds before starting again. Luckily if I watch a playlist and it goes to the next video, there is no time to leave.

  At one point, I decided to try to uninstall and reinstall new IDT Audio, I think a few days before I scanned with Malwarebytes and then after restarting the laptop installed Windows audio in itself, so I have more IDT Audio in my list of programs. I also tried to restart all audio related services in Services.msc this morning to see if there was a solution similar to the restart of the themes bring Aero, but it did not work.

  So is anyone know how I could fix this audio delay? Even if it does not completely and it is not that I do whenever I start my laptop as the restart of the themes that's fine. I am really annoyed to have to wait a few seconds every time I have a video paused for more than 20 seconds.

  I was discussing this announcement in the operating system and Council of recovery due to the System Event Notification Service error, but since both problems started happening after an audio problem, I figured it belongs here instead.

  I've been making event 6281 constantly in my observer of events since the beginning of this problem, the night that I reinstalled IDT Audio. It reads:

  "Code integrity determined that the page of an image file hashes are not valid. The file could be incorrectly signed without hashes or corrupted due to an unauthorized change page. Invalid hash values can indicate a potential disk device error.

  ' Name of the file: \Device\HarddiskVolume2\Windows\System32\SRSLabs\{176F4E15-8F7C-4833-ADED-81FAE8CCD186}\slcc3d64.dll ".

  Is slcc3d64.dll an audio related thing?

  I solved it mine this morning! I uninstalled IDT Audio again and went into the SRSLabs folder in system32, to find these two DLLs and another file, were still there. So, I moved the folder SRSLabs in the Documents so that they don't touch anything and restarted my laptop. Windows has installed its own driver audio, and that solved the problem. I get is more 6281 event in Event Viewer, and the audio delay has disappeared. Audio driver Windows installed on its own sounds just as good as the pilot Audio IDT is also, so I'll stick with it!

  I hope that double posting is perfect? I tried to search for a thread of the forum rules and could not find one.