Dell Dimension 5150 do not start LED logo on 123 + progress bar is stuck at 5% no beeps

Similar Questions

• Dell Dimension C521 does not start

  I have a Dell Dimension C521 desktop computer. When I try to start it, the fan turns on and is really hard, but the screen does not light. The power light on my computer lights up (green), but the 3 & 4 diagnostic lights flash repeatedly on the front of the computer. What is the cause? What can I do about it?

  NetFanatic123

  Hello Bev,

  The rest green power light on, no blinking, no beeps. I had no problem until last night after that I removed the hard drive and reinstalled.

  How can I remove the memory modules?

  Thanks :)

   

  NetFanatic123

  For the removal and reinstallation of the RAM, details are HERE NOTE from the ADMIN: broken link has been removed from this post by Dell >

  A hint: make sure that the modules are filled into the slots and the clips are in the notches.

  While the case is open, check that all the power cable and the data are correctly connected to the drive and the motherboard, by removing and reconnecting them.

  Why the hard disk has been deleted and reinstalled, was this HD replacement, or what?

  Bev.

• Dell Dimension 4600 does not start after upgrading CPU

  Hello

  First of all, I tried to send this last night but received a message on my post approval by moderator? Not yet been approved but seen other people have posted with success more recently. Do not know what is happening.

  In any case, put his hand on a 3.4 Ghz HT P4 Northwood 512 Kb 800 Mhz FSB for £10 on Ebay to upgrade my mother enough old Dimension 4600 which has a 2.8 Ghz P4 512 KB 533 FSB inside... However, when I install it the computer does not light and shows just a light amber. The readers and fans still spin but there is no display. The computer works normally when I put the old one back in.

  I think somehow it is a power supply problem as the new processor uses 20w more energy than the old 2.8 Ghz one. Someone at - it ideas? Just trying to figure if I bought a bad CPU, so I can return.

  Thank you

  Andrew

  AV115

  Hello

  First of all, I tried to send this last night but received a message on my post approval by moderator? Not yet been approved but seen other people have posted with success more recently. Do not know what is happening.

  In any case, put his hand on a 3.4 Ghz HT P4 Northwood 512 Kb 800 Mhz FSB for £10 on Ebay to upgrade my mother enough old Dimension 4600 which has a 2.8 Ghz P4 512 KB 533 FSB inside... However, when I install it the computer does not light and shows just a light amber. The readers and fans still spin but there is no display. The computer works normally when I put the old one back in.

  I think somehow it is a power supply problem as the new processor uses 20w more energy than the old 2.8 Ghz one. Someone at - it ideas? Just trying to figure if I bought a bad CPU, so I can return.

  Thank you

  Andrew

  AV115

  Andrew,

  It is not a power supply problem, it's incompatible, or a bad processor problem.

  The first models of 4600 will take up to 3.0 GHz and models later, 3.2 GHz to 3.4 GHz, but this does not offer much of a sudden boost on the 3.0 GHz

  Motherboard Dell P/N F4491 will support up to 3.4 Ghz Northwood leaving Prescott

  Bev.

• Dell Dimension 9150 will not start, turns 2, 3

  Hi all

  I moved to Italy and handed the dip switch at the rear of the server to 230v.  The computer starts beeping sound and light indication of storage 3 and 4 is stable.   The monitor does not work and I get a warning on the screen there is no signal.  I hope someone can shed some light?  I'm not a computer guru, but I can try to work the steps to make it work because there a lot of personal things in what I would like to have access.   Thank you

  Well speak of the devil, I moved the Ram in slot 1, since it was not positioned in slot 1, but 4 and now the dell is starting up and works FINE... which is great!  I am a woman with a bit of left brain!

• My dell optiplex 740 will not start. The screen is black, once it displays the Dell logo. It does not say that the computer is in mode 'sleep'.

  My dell optiplex 740 will not start.  The screen is black, once it displays the Dell logo.  It does not say that the computer is in mode 'sleep'.

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You receive an error message?

  Method 1

  See the articles below and check if it helps.

  Computer stops responding with a black screen when you start Windows XP

  http://support.Microsoft.com/kb/314503

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

  Method 2

  I suggest that you start the computer in the last good known Configuration mode and safe mode, post back with the result.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  How to start your computer by using last good known Windows XP Configuration

  http://support.Microsoft.com/kb/307852

  How to fix a computer that does not start

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/how-to-fix-computer-that-will-not-start

  Method 3

  If the computer can boot in any mode, then I suggest that you perform the clean boot procedure and check if it helps.

  It is possible that some third-party programs installed on the computer is causing the problem.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• Dell Dimension 5150 - WinXP error 0 x 00000024 STOP

  I wrote this email to someone, however, received no response, so am using Microsoft Answers.
  Any help would be GREATLY appreciated.

  Thanyou,

  Anil

  Dear Dan,

  First of all, my name is Anil and I found your E-mail address when searching about my problem on some Forums.

  Last night, my computer was working fine. Really flawless. I use a Dell Dimension 5150 running Windows XP.

  However, when booting this morning, I received the error STOP 0 x 00000024 and with something to do with CHDSK / F.

  I couldn't do anything, like when I tried to boot my PC in safe, I got the same blue screen with the error.

  Therefore, after reseaching, I found two possible solutions.

  The first is to use the WinXP disc, however, my PC came with Windows XP already installed, I therefore had no disc.

  The second, I found the Forum even where I found your Email address, is to use a program called Bart PE Builder.

  I used Labtop this and this to burn the program to a CD.

  I only have a cause for concern, and it is, I have about 30GBs of value of music on my computer that I would be afraid to lose.

  My question is, if I run PE Builder from Bart, my music will be lost?

  And that goes for other files and documents on my computer (anything illegal, don't worry; (P)

  Thank you

  Anil

  Looks like Bart's not see anything except himself and that might be because it takes the controller drivers that are added. The easy way to find out is to add drivers to the image of your Bart controller and then start with this new CD. IIRC, he must put the drivers in a certain directory. Site Web de Bart, user forums or Google will tell you how. I don't use often Bart (preferring Knoppix) so know not glib. MS - MVP - Elephant Boy computers - don't panic!

• Dell dimension 5150 Cpu Upgrade help?

  Hi, I have a dell dimension 5150 3 GB of ram I currently am all an Intel Pentium d 2.8 ghz (LGA 775), and I was wondering what is the best upgrade can take my motherboard 0HJ054. Full specifications below.

  -Plug-

  TXT of CPU - Z report
  -------------------------------------------------------------------------

  Binary files
  -------------------------------------------------------------------------

  CPU - Z version 161.2

  Processors
  -------------------------------------------------------------------------

  Number of processors 1
  Number of threads 2

  APICs
  -------------------------------------------------------------------------

  Processor 0
  -Core 0
  -Wire 0 0
  -Core 1
  -0-1 wire

  Information for processors
  -------------------------------------------------------------------------

  Processor 1 ID = 0
  Number of cores 2 (max 2)
  Number of threads 2 (max 2)
  Name Intel Pentium D 820
  Codename SmithField
  Specification Intel (r) Pentium (r) D CPU 2 .80GHz
  Package (platform ID) Socket LGA 775 (0x4)
  CPUID 4.7
  F.4 extended CPUID
  Core Stepping B0
  90 nm technology
  Basic speed 2796,3 MHz
  X FSB multiplier 14.0 x 199,7 MHz
  798,9 MHz rated Bus speed
  Stock frequency of 2800 MHz
  Instructions sets MMX, SSE, SSE2, SSE3, EM64T
  Data L1 cache 2 x 16 KB, size 8-way line set associative, 64 bytes
  Hidden trace Kuops 2 x 12, 8-way set associative
  L2 cache 2 x 1024 KB, size 8-way line set associative, 64 bytes
  FID/VID control not

  Chipset
  -------------------------------------------------------------------------

  Model of motherboard 0HJ054
  Northbridge Intel i945P/PL/G/GZ Rev A2
  Southbridge Intel 82801GB (ICH7/R) Rev A1
  Memory type DDR2
  Memory size 3072 MB
  Double channels
  Frequency memory 266,3 MHz (3:4)
  Latency CASE # (CL) 4.0
  # For CASE # delay (tRCD) RAS 4
  RAS # Precharge (tRP) 4
  Cycle Time (tRAS) 12
  (TRC) Bank Cycle time 16
  Base address e/s MCHBAR 0x0FEDA0000
  E/s MCHBAR size 4096

  Memory SPD
  -------------------------------------------------------------------------

  DIMM # 1
  SMBus address 0 x 50
  Memory type DDR2
  Regular UDIMM module format
  MOSEL manufacturer (ID) (4000000000000000)
  Size 512 MB
  Band bandwidth PC2-4300 (266 MHz) max
  V916764K24QAFW-E4 part number
  Serial number 1153079D
  The year of manufacture date week/31/06
  Number of banks 1
  64-bit data width
  Correction no
  Nominal voltage 1.80 Volts
  EPP no
  XMP no
  Timings JEDEC CL-tRCD-tRP-tRAS-tRC table @ frequency
  JEDEC #1 3.0 - 3-3-8-11 to 200 MHz
  JEDEC #2 4.0 - 4-4-11-15 at 266 MHz
  JEDEC #3 5.0 - 4-4-11-15 at 266 MHz

  DIMM # 2
  SMBus address 0 x 51
  Memory type DDR2
  Regular UDIMM module format
  Manufacturer (ID) PNY Electronics (7FBA000000000000)
  Size 1024 MB
  Bandwidth Max PC2-6400 (400 MHz)
  Part number
  Number of banks 1
  64-bit data width
  Correction no
  Nominal voltage 1.80 Volts
  EPP no
  XMP no
  Timings JEDEC CL-tRCD-tRP-tRAS-tRC table @ frequency
  JEDEC #1 4.0 - 4-4-12-16 at 266 MHz
  JEDEC #2 20 5.0 - 5-5-15 @ 333 MHz
  JEDEC #3 6.0 - 6-6-18-24 @ 400 MHz

  DIMM # 3
  SMBus address 0 x 52
  Memory type DDR2
  Regular UDIMM module format
  MOSEL manufacturer (ID) (4000000000000000)
  Size 512 MB
  Band bandwidth PC2-4300 (266 MHz) max
  V916764K24QAFW-E4 part number
  Serial number 5954079C
  The year of manufacture date week/31/06
  Number of banks 1
  64-bit data width
  Correction no
  Nominal voltage 1.80 Volts
  EPP no
  XMP no
  Timings JEDEC CL-tRCD-tRP-tRAS-tRC table @ frequency
  JEDEC #1 3.0 - 3-3-8-11 to 200 MHz
  JEDEC #2 4.0 - 4-4-11-15 at 266 MHz
  JEDEC #3 5.0 - 4-4-11-15 at 266 MHz

  DIMM # 4
  SMBus address 0 x 53
  Memory type DDR2
  Regular UDIMM module format
  Manufacturer (ID) PNY Electronics (7FBA000000000000)
  Size 1024 MB
  Bandwidth Max PC2-6400 (400 MHz)
  Part number
  Number of banks 1
  64-bit data width
  Correction no
  Nominal voltage 1.80 Volts
  EPP no
  XMP no
  Timings JEDEC CL-tRCD-tRP-tRAS-tRC table @ frequency
  JEDEC #1 4.0 - 4-4-12-16 at 266 MHz
  JEDEC #2 20 5.0 - 5-5-15 @ 333 MHz
  JEDEC #3 6.0 - 6-6-18-24 @ 400 MHz

  Mike 5150

  Next post should help,

  http://en.community.Dell.com/support-forums/desktop/f/3514/p/19436963/20053889.aspx#20053889

  Before installing the processor, verify that the version of the BIOS A05 or higner is installed, when support for the latest processors has been added.

  Bev.

• Update graphics card in Dell Dimension 5150

  Hi all, I have a dell dimension 5150 with a graphic card intel r I would improve my chart to something better, it will be mainly used for live streaming TV & other thingscan someone please advise me a graphics card more powerful I checked graphics cards in previous discussions, but most of these cards have been abandoned advice on which current maps to go thank you Savio

  busymomof4

  Thanks for your comments.  It really helps us less tech savvy moons follow through technology.

  The 9400GT is an ancient design. There are many new video cards compatible with food of the 5150 stock, like Sapphire 6450.

• Upgrade CPU Dell Dimension 5150. Is the cooling system to work?

  I have a Dell Dimension 5150 with a Pentium 4 HT 630 (84 W tdp). I want to replace it with a Pentium D 920 (95W tdp) is the heatsink and the fan is going to face? I'll be cleaning and demean the new thermal paste.

  PonderBoy

  Yes, the default heat sink and fan should be thin.

  Bev.

• Dell Dimension 5150 won t boot

  Hey guys! My Dell Dimension 5150/510 running Windows XP Home Edition SP3 won't boot for some reason any. Whenever I press the power button the power button just blinks and won't turn on. Please help as soon as POSSIBLE. Thank you! If you can do it in a video or BIC please :(

  md5diablo

  All that, suggest a power failure, first replace the PSU with a unit of work that is 'known', to see if that makes a difference.

  5150/E510 systems don't use exclusive Dell power supplies, you can install a generic ATX power supplies with either a power connector 24 pin or 20 + 4 pin main motherboard.

  Like the 5150/E510 has a rear panel open, a diet with or without the on/off switch can be used and can be purchased in most local computer stores or online.

  Need a power supply with two SATA power connectors.
     
  Bev.

• Stuck on Start Up Apple screen logo with 50% progress bar, tried everything. Help, please!

  Hello world. I'd appreciate it really all the advice that you can offer me to help me fix my laptop. I have a mid-2010 Pro 2.4 GHz Core 2 Duo Macbook running OS X Yosemite. A year ago, he started trolling a lot, so replaced the HDD with a Samsung 850 EVO 120 GB SSD internal 2.5 inch SATA III. He works much better since.

  A few days ago, I bought a Google Chromecast and had set up with my MBP. Subsequently, he began trolling and I noticed there are apps in the Launchpad, that I had never downloaded (reader of Google, Gmail, Youtube, etc.). I could not remove these applications or drag them to the trash. Concerned, I decided to back up my files on a USB key and re - install the OS X.

  However, during the priming of the MBP, it is stuck on the Apple logo screen, with the bar never go beyond 50%. (Photo: http://postimg.org/image/66qh6x633/)

  What I tried:

  PHASE 1 (Before reformatting)

  -Safe Mode: Button power button and shift held down. Hit or miss, worked 1-2 times, but when I reboot, is again stuck at the Apple logo.

  -Reinstall OS X: CMD + R; After 15-20 minutes get to OS X utility screen; Reinstalled OS X Yosemite; 7 hours to reinstall - but when the mbp restarts to complete the installation, it is stuck at the Apple logo again.

  -Reformatting: CMD + R; 15-20 minutes get to OS X utility screen (several reboots to work); Select repair for all discs/drives (Samsung SSD, HD Recovery). Exit said that both are very good; Select clear to HD recovery. When this was done, I tried to reinstall OS X Yosemite, but the MBP shuts down suddenly. When I turned on it again, it is returned to be stuck on the loading screen Apple logo. Attempt to restart after 15 +, but same result every time.

  PHASE 2 (After reformatting).

  -Power-> CMD + R = blocked screen Apple logo with 50% progress bar

  -Power-> Option = shows 2 player and free Wi - Fi area (Pic: http://postimg.org/image/58qi2j1vl/); Have you tried all the combinations, but regardless, always gets stuck at the screen of the Apple logo to 50% complete, after an hour, I suddenly hear ' to use English as the main language... ". ", but the screen is still stuck. I left it on 36 hours once and nothing has changed

  -Power-> Shift = error (Pic: http://postimg.org/image/tahklsvy1/); Keep restarting or shows some other error (Pic: http://postimg.org/image/thstc6b59/) and restart. Never crosses.

  Tried other things:

  -Reset PRAM: When restarting MBP, is stuck at the Apple logo screen, 50% progress bar

  -Reset SMC: Stuck on the Apple logo screen for a long time and then the screen turns off, but the laptop is still on. When I press Caps Lock, the indicator light lights up. Also, after some time, I again hear "to use English as...". "even if the screen is off. No matter what I press, it does not wake up to the screen.

  Note:

  -The bottom of the laptop feels hot (maybe), but I do not hear the drive in motion.

  I am trying to save my mbp because I can't get a new one for a few months. Any advice/help is greatly appreciated! Thank you very much!!!

  P.S.: I only am not too computer savvy, please use everyday words words/non-tech, when possible, thank you!

  Remove the SSD and install it in a closed Chamber.  Connect it to the MBP via USB.  It will start?

  Ciao.

• my system does not start upwards - don't stop progression blue bar that goes round and round. I can boot into safe mode and safe mode with networking mode.

  my system does not start upwards - don't stop progression blue bar that goes round and round.  I can boot into safe mode and safe mode with networking mode.

  Hello

  As you are able to boot to the desktop in Mode safe, it means that the third-party application prevents the computer from starting in normal mode. To check you can configure the computer to clean start State and then try to boot into normal mode and check what is happening. To set up its own start-up follow the link below.

  http://support.Microsoft.com/kb/310353

  If the problem does not continues when the computer is in the clean start State follow the steps listed to identify which application is causing the problem.

  Note: When you are finished troubleshooting, follow step 7 article to start on normal startup.

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Dell Dimension 2400 will not meet the key USB WIFI Netgear

  Dell Dimension 2400 Windows XP.

  Trying to get my old Dell back in action, but I ran into a problem. NO INTERNET.

  I have the WIFI in my house but I can't connect wirelessly with the desktop computer.

  I have a NetGear Wireless - N Dual Band, but dell WNDA3100 USB won't pick it up. The flash player is on, but it will not install the new software. It is said there was a problem and it probably won't work correctly.

  Any ideas? Thank you!

  first go to the device driver and uninstall everything dealing with netgear.

  also if it is listed in Add/Remove to uninstall and restart.

  https://www.Google.com/#q=NETGEAR+Wireless+n+dual+band+WNDA3100+USB+XP+installation+guide+and+software

  above is a search page with instructions for installing xp

  you have version 1 or 2?

  just a thought you have wireless zero config service started/automatic services?

  After all your updates should be installed which will disable the autorun, so that when you insert a usb key, nothing will happen until you go to my computer and click on the device to open it, this was done so that you would have a chance to scan a usb usb being one of the fastest ways to spread a virus If she had previously plugged into an infected pc.

• Dimension 8400 will not start up cd or dvd drive

  Hello

  I have a Dimension 8400 that refuses to boot from the CD or dvd drive. In the bios, tried to move 'Onboard or USB CD-ROM Drive' to the first position in the boot sequence. Also, I tried pressing "f12" during startup to access the start menu. I tried to select the "integrated or usb cd-rom" option from there with a cd bootable in both drives and still have had no success.

  Any help will be greatly appreciated, thank you.

  I also have the same problem.  Do not understand why Dell does not address this issue.  Trying to recharge a system using the Dell restore CD and have two CD drives in the system provided with the system and will not start to :(

• Dimension 8200 does not start

  I have a Dimension 8200, which has not been used for more than a year.  I was going to reformat the hard drive to remove all personal data, and then give it to my daughter's school.  However, it will not start.  The Dell page comes and the BIOS white bar at the bottom of this page fills slowly, but then nothing happens for about a minute.  Meanwhile, the power button is green, and the ABCD diagnostic lights are green-orange to orange-green.  Then after about a minute or two, a page of message arrives.    At this point, the diagnostic lights are Green-Green-Green-orange, and the power button is always green. Among other writings is the assertion that the 1 primary and secondary hard drives is not found.  It says also "failure keyboard,' even if I used this fairly reliable keyboard with other computers. But it does not seem that the keyboard doesn't have - I do nothing doing on the keyboard has an impact on the computer.

  I checked the optical drive opens and closes when I push the button on the front, but I have not tried to use the player, because the computer is completely non-functional.  I looked through the forum of ideas of things to try.  According to this research, I checked the power supply provides the correct voltage.  I disconnected and reconnected then the two IDE cables, and I also removed and replaced the RAM sticks, as well as two sticks of continuity.  But still nothing!

  Any ideas, or should I just trash?

  Thank you

  laserguy

  Dell Dimension 8200

  Windows XP, SP2

  Pentium 4 CPU, 2.26 MB RDRAM GHz512

  80 GB Maxtor hard drive