Dell poweredge R210 II BMC communication failure

Similar Questions

• U1 ESXi 4.1 install on Dell PowerEdge R210

  Have no success in installation of the ESXi 4.1 U1 on the Dell PowerEdge R210? I'm unable to install ESXi and maybe someone had some advice. The Dell server comes with a RAID1 and is under the list of VMWare HCL. There a S100 for the RAID controller. Dell recommends to break the RAID1 and install ESXi on the local drive (single). This server comes with a 500 GB drive (x 2).

  What will be the best option? I think to install the 4.1.U1 ESXi on a USB key, but had no experience this and I don't know how is it sustainable. I can count on and what size of USB do I need?

  Please advice what have you done or any recommendations on how to install the server host.

  Thank you.

  Collin

  I'd certainly install on a USB key. You will need a 1 GB or more large USB key. You can have an internal USB slot and I would like to check the documentation for your location. ESXi loads directly into RAM, and he has very little written on the disc. A copy of the small configuration happens once per hour.

  I don't think that your RAID controller can be used as RAID because I think it's a software RAID that is not supported under ESX (i). You will end up with two separate drives.

• Failure installing ESXi 5.1.0 on Dell PowerEdge R210 II

  Hi all

  I tried to find my answer in the existing forums and found a similar mistake (Forum #423438), but he had put end to saying that particular server is not supported. I bought the different server, the PE210 II, and he showed up on the list of support for VMWare. If you need of advice please.

  It is a new server out of the box, bought without Windows/Linux installed. Get the installation to the point below where it was looking to select a drive... and he just stood there. When I hit F1 for more details, I got the text at the top left of the screenshot. "An unexpected error has occurred. Error code: YMxvZy5we... "Look at the logs for more details. AttributeError: 'Text' object has no attribute 'device'

  

  No idea how to go beyond this? Really, we want to start using VMware and bought equipment to devote to it. Now I can't make it work.

  Thanks in advance for any help you can provide.

  Scott

  Unfortunately "S" PERC controllers don't are not supported with ESXi, it may not even be detected during installation at all (see KB VMware: cannot install ESX/ESXi with Dell S class PERC)

  André

• DELL PowerEdge R210 - riflettore guasto [CF]

  Buongiorno,

  Abbiamo UN alimentatore guasto fuori co sul server in oggetto.

  Questi i dati del server in oggetto:

  Serial number: C76K212 | Express service code: 26555664710

  Could stuffed avere un preventivo by ricambio it?

  Todas

  Davide Paltretti

  Distelco srl

  Buogniorno, sto contattando by mail.

• PROBLEMI WINDOWS SERVER 2012 R2 SU SERVER DELL PowerEdge R210 II PUMPS

  Ho downloaded the Immagine ISO della versione di prova dal portale di microsoft di Windows Server R2 2012, accendo it server accedo went fruit F10 by prima cosa ho tried a rates come sorgente CD my it sistema mi international it following message "do not find the catalog file. Make sure that the catalog Windows (R) and Dell (TM) update packages for Windows (R) are userd' o tentanto Reed selezionando FTP my it sistema mi international it following message "updates that you are trying to apply are not up-to-date approved from Dell.

  Potete darmi directions in merito. Grazie

  Buongiorno, io ho asked su information come procedere... No ho asked UN preventivo di spesa

• Setting up raid 1 on dell poweredge r210 ii

  Hi all

  I want to configure raid 1 with 2 x 500 GB sata HDD, I tried pressing f10 when the thumb to the Configuration Wizard of server load when I press on the raid configuration, I got error no. controllers Raid found! ..

  any help please

  Thanks in advance,

  Mandoesam,

  The first thing I would look at is if the Raid is turned on in the BIOS (F2). Access the BIOS, and then under SATA settings, replace the SATA Embedded Raid Mode. You can also turn off the server and reconnect both ends of the HDD cables. After that, then start the cycle of life of the controller (F10) and see if the Raid is now configurable.

  Let me know how it goes.

• [EC | ex-MS |] Solved] RIPARAZIONE FUORI CO POWEREDGE R210

  Buongiorno,

  Abbiamo need di UN preventivo per UN POWEREDGE R210.

  The macchina e fuori co.

  I have a problemi riscontrati sono:

  -Ventole sempre accese

  -Al boot so i seguenti if mi

  System Service disabled

  BMC Communication failure

  SERVICE TAG

  Come we can procedere?

  Buongiorno,

  Visto error riportato "Bmc Communication Failure" non e possibile aggiornare bmc which even comanda Reed it system service the ventole, is replace the motherboard.

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could mandarmi come message privato di seguito required information?

  By the spedizione/operation:
  1. company name:
  2 address:
  3 City:
  4 Provincia:
  5 cap:
  6 name/last name/number phone/e-mail del referent in loco:

  With the fatturazione
  1 nome società:
  2 via:
  3 City:
  4 Provincia:
  Heading 5:
  Name/last name/number 6 telephone/e-mail del referent by the fatturazione:
  7 partita IVA

  Speaking saluti

  Manual

• Cannot update firmware Poweredge R210 II

  Hello

  I get messages and errors below when you try to update the firmware on my server Poweredge R210 II. I use the BIOS of the Dell PowerEdge R210 II Version 2.8.0 server that seems to be the most recent version of this BIOS, but receive the following messages:

  * Red * please do not remove his power!

  Utility of flashing Insyde etc.

  100% of file loading

  Model name of the current BIOS:

  New model of the BIOS name: PowerEdge T110 II

  * Red * cannot use a BIOS "PowerEdge T110 II".

  * Red * in a «»

  * Red * Rom update not done

  etc.

  I saw the post following for the server in the subject line that has the same message above and points located on the server is an OEM box, but I'm able to open a support on the dell.com site page using the number of service on my machine. Any suggestions? Here is the message:

  http://en.community.Dell.com/support-forums/servers/f/956/t/19429285.aspx

  I managed to Flash the BIOS on my Dell R210 II XL OEMR back to the standard BIOS Dell Server version 2.8.0 by creating a BACK USB startup disk, copy the unpackaged Dell BIOS file, in my case, I used PER210II_020800.exe, and then running the following command: "PER210II_020800.exe - wipeclean - forcetype.

  The switch - wipeclean clears the ESCD and DMI data tables and the forces of switch - forcetype BIOS file to install on any Dell server.

  Here is a list of the other switches used during the update of the BIOS.  Be careful, however, you easily could brick your server if you use these incorrectly.

  mickitblog.blogspot.com/.../Dell-BIOS-switches.html

• Request preventivo motherboard for PowerEdge R210 [CF]

  Buongiorno,

  Abbiamo need di UN preventivo per sostituzione card mother relative al PC Dell PowerEdge R210 fuori co serial number 1LVCX4J.

  Restiamo in attesa di una vs cortese risposta.

  Todas

  Davide Paltretti

  Distelco s.r.l..

  Buongiorno, the sto contattando by mail.

• Dell PowerEdge 1950 BMC help!

  Hello

  I thought that the server takes a long time to start. I hooked up to a monitor and found that the BMC was having a "communications failure". I found also that the DRAC5 installed on the server was not working. I scoured the forums and I read the update from the BMC would solve this problem. I have 2012 R2 server installed on this system, so I downloaded the 2.50 for the BMC update (.) (EXE) and started to install it, fans crawls up to maximum speed and then I got a BSOD when the server restarts the PERC6 now cannot see my 2 TB drive that windows (SATA) installed, he can see the 300 GB SAS drive.

  Is it possible to get my 2 TB hdd working again and to get the BMC to work?

  Thank you

  Hardware and software failures occur. May not have been avoided. However:

  You might have been able to reflash the firmware BMC (unless it is completely unresponsive or nonfunctional).

  You may have attempted to clear the system NVRAM.

  As far as the reader goes. It is very important to learn the difference between CLEAR and IMPORT and when to use one or the other.

  Finally, consumer/desktop/computer portable readers should not be used in servers. WD Green, blue and Red are all bad choices for use on RAID of company systems.

• DELL Poweredge 2900 - disk failure

  Hello

  We have an old Dell Poweredge 2900 our SQL Server database running server.  Last week, we discovered that Raid 5 is degraded and disk 0 disk 1 is seeing completely to the bottom and the poster.  We were already down, so even if we had it running by buying a replacement of the SAS 146 GB 10 k disk we would still be short of storage of data of space.  I bought a SAS Seagate Cheetah 15 k 600 GB ST3600057SS and I would like to replace the failed drive with it.

  Question:

  (1) open handle is not installed, but want to install.  What version I can use for this 2900 server.

  (2) my replacement of a 146 GB with a 600 GB can work?

  Please for your advisor as this database server is essential for my operation of the company.

  Thanks in advance

  Hello.

  ISOSA

  (1) open handle is not installed, but want to install.  What version I can use for this 2900 server.

  Download OpenManage Server Administrator v7.4.0.2 form this link: http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=MGRG4

  ISOSA

  (2) my replacement of a 146 GB with a 600 GB can work?

  Replacing 146 GB with 600 GB of disk drive will not provide any extra space you need because the table will use only 146 GB of total space 600 GB on the new drive. What controller you have installed? In case the only option available for you that your controller does not support the extension of ability online (ECO) could be to backup your data, delete the existing RAID array and re - create another table with the new readers of 600GO. Restore data from backup and re-install the operating system.

• Card LaCie esata PCI card on windows 2003 server Dell poweredge T410 error code 10

  Hi guys, I am trying to install a new card Lacie esata PCI card (http://www.lacie.com/products/product.htm?pid=11217) on windows server 2003 on Dell poweredge T410. Windows detects the card and install the driver, but then, it shows an error code 10 "device Can not not started. I tried the update, uninstall, reinstall, adding Lacie driver CD through the "Hardware Wizard', chaning PCI card slot by 4 to 1. But nothing has worked. So please let me know if you think that there is a fix for this solution. Thank you

  Hi Rlap,

  The question you have posted is related to Windows Server and would be better suited to the TechNet Discussion groups. Please visit the link below to find a community that will provide the support you want.

  Windows Server Forums: http://social.technet.Microsoft.com/forums/en/winservergen/threads

• (Redirected) Dell poweredge 1950

  I have a dell poweredge 1950 server that was given to my school and I am trying to install windows server 2003 on it, but an error saying:

  Setup did not find any hard drives installed in your computer.

  Make sure that the hard drives are powered on and properly connected to your computer, and that any hardware configuration of the drives is correct. This may involve a diagnosis provided by the manufacturer or the installer running

  How can I fix?

  I also tried to boot Ubuntu from a usb key and that no longer works.

  I also said to update BIOS or Flash the Bios but I don't know how to do and do not know if that'll fix it.

  I want to just get to the top and running, it can be Ubuntu or windows everything is easier.

  Any help would be greatly appreciated

  Better for this post in the Forum Server-PowerEdge, here:

  http://en.community.Dell.com/support-forums/servers/default.aspx

  Bev.

• Request price diretto FAN by server PowerEdge R210 II

  Buongiorno,

  Abbiamo indivuato UN guasto due ventole del Server PowerEdge R210 II (service tag: 7K556X1) da noi injected.

  Richiediamo one ' offer by the price di n.2 ventole by suddetto server there.

  5s a gentile riscontro vostro.

  Saluti

  Buongiorno, the sto contattando by mail.

• (Redirected) Card SCSI Dell poweredge 1951 backlane

  Hello world

  I installed and running a Dell poweredge 1950 that I use it to backup (tape) using Backup EXEC 2014. In the alley, he has an empty slot for a SCSI expansion card where a need can connect via a SCSI connection a different external tape drive. Due to the fact that the dell model is quite old, it is difficult to find a type of card.

  I found online something to my request: [View:www.amazon.co.uk/.../ref=sr_1_fkmr1_2]

  but the problem is that it has two SCSI ports and it is too big to get it. I tried to find one with a single port, but I can't seem to find it. Have you also had this problem and if so where you bought the SCSI expansion? There is also the option to purchase a SCSI cable / USB, but I don't want to go with this solution. All advice what to do or where to buy expansion card I need.

  Thanks for the tips.

  Best of this post in the Forum servers, here:

  http://en.community.Dell.com/support-forums/servers/default.aspx

  Bev.