Similar Questions

• Dell PowerEdge Fans always runs in full speed

  Hello

  I have a problem with a Dell Poweredge 2900 server witht. The server is still running the fans at full speed.

  I tried to update the latest version of the bios and the firmware for environmentally sound management, but the problem is not resolved.

  Dell OpenManage shows only a single error, said of the intrusion into the chassis, casing is open, but case is closed properly. I think that the sensor is bad, I try to look for the switch, but I can't.

  Please let me know where is the switch of intrusion of the chassis on this server, or how to disable.

  Thank you

  As suggested by Theflash1932, the intrusion switch may be damaged and located on the Bay of housing Center fan. It cannot be replaced as one of its components. See the image below.

  

  It is replaceable like a Bay of housing of Dell part number: NF078

• Card LaCie esata PCI card on windows 2003 server Dell poweredge T410 error code 10

  Hi guys, I am trying to install a new card Lacie esata PCI card (http://www.lacie.com/products/product.htm?pid=11217) on windows server 2003 on Dell poweredge T410. Windows detects the card and install the driver, but then, it shows an error code 10 "device Can not not started. I tried the update, uninstall, reinstall, adding Lacie driver CD through the "Hardware Wizard', chaning PCI card slot by 4 to 1. But nothing has worked. So please let me know if you think that there is a fix for this solution. Thank you

  Hi Rlap,

  The question you have posted is related to Windows Server and would be better suited to the TechNet Discussion groups. Please visit the link below to find a community that will provide the support you want.

  Windows Server Forums: http://social.technet.Microsoft.com/forums/en/winservergen/threads

• Dell PowerEdge Server - IDRAC R720 problem

  Dear support team

  I have a Dell PowerEdge R720 not ready iDRAC server. The configuration values are not available. very strong fans noise, please notify

  Hello

  I'll send you an email to ask for the serial number. Thank you

  Marco

• HP StorageWorks MSL2024 tape library integrate R720 Dell Poweredge

  Hello

  I have a dell Poweredge r720. I want to integrate HP MSL 2024 so I need to install the LSI SAS9212-4i4e interface card.

  Is this compatible with poweredge r720?

  Hello simpleguy3k,

  This is a combo card because if you connect hard drives you can use it as a raid card, or if no drive is directly connected to the card then it can serve as a relay SAS card. Also, I checked the compatibility of the guide & it supports two different tape units. http://www.LSI.com/downloads/public/host%20Bus%20Adapters/host%20Bus%20Adapters%20Common%20Files/LSI_6Gb_SAS_SATA_HBA_Compatibility_List.PDF

  Please let us know if you have any other questions.

• DELL Poweredge 2900 - disk failure

  Hello

  We have an old Dell Poweredge 2900 our SQL Server database running server.  Last week, we discovered that Raid 5 is degraded and disk 0 disk 1 is seeing completely to the bottom and the poster.  We were already down, so even if we had it running by buying a replacement of the SAS 146 GB 10 k disk we would still be short of storage of data of space.  I bought a SAS Seagate Cheetah 15 k 600 GB ST3600057SS and I would like to replace the failed drive with it.

  Question:

  (1) open handle is not installed, but want to install.  What version I can use for this 2900 server.

  (2) my replacement of a 146 GB with a 600 GB can work?

  Please for your advisor as this database server is essential for my operation of the company.

  Thanks in advance

  Hello.

  ISOSA

  (1) open handle is not installed, but want to install.  What version I can use for this 2900 server.

  Download OpenManage Server Administrator v7.4.0.2 form this link: http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=MGRG4

  ISOSA

  (2) my replacement of a 146 GB with a 600 GB can work?

  Replacing 146 GB with 600 GB of disk drive will not provide any extra space you need because the table will use only 146 GB of total space 600 GB on the new drive. What controller you have installed? In case the only option available for you that your controller does not support the extension of ability online (ECO) could be to backup your data, delete the existing RAID array and re - create another table with the new readers of 600GO. Restore data from backup and re-install the operating system.

• [Solved] Dell PowerEdge R720: Error when will United Nations datastore in VMware ESXI 5.1.0 [SD]

  Buonasera,
  HO a Dell PowerEdge R720 fuori co, build 799733, non riesco ad add a datastore not found da dipped 1.8 to.
  Durante FICS 'add a storage' seleziono disk/Lun, VMFS5, per poi was "Current Disposition of the disc" al, nella casella vedo the con dei locali brain table a couple of partizioni di default.
  Dopo few minuto di attesa mostra una finestra in cui VSphere loses the e outdo if sta tentando di ricollegare.
  Can I try a ricollegarmi senza esito, dopo some UNAMET outdo e di nuovo attiva

  This is the che viene say error:
  Call "HostDatastoreSystem.QueryVmfsDatastoreCreateOptions" of object "ha-datastoresystem" on ESXi '10.2.99.36' failed.

  He guardando Dell Disco local delle partizioni noto:
  1 XXX DatastoresAndVolumnes.PartitionType.0xde not found...
  2 Win95 FAT32 LBA 2.00 GB

  No Yes di cosa is... If my alla fine ho need understand di causa e come lo spazio image Add.
  Allégo ibm_db del disco inquisito: naa.6848f690edfa310018e37ce915ef3fcf

  Come posso lo senza riavviare storage server add it?
  The partizioni in questioned are best-known boot di durante FICS? Oppure posso eliminarle?
  CI sono dei comandi specifici per creare he vmfs volume?

  Grazie in pre-empted by it vostro aiuto

  Salve,

  No we can aiutarla a software level. It forum dedicated to e a soli problemi hardware.

  If dovra rivolgere o al supporto Vmware o a terze aziende.

  Speaking saluti

• Server Tower Dell PowerEdge T110 II

  Hello

  For server Dell PowerEdge T110 II Tower

  If I choose

  Microsoft (r) Windows (r) Server 2008 x 64 R2 SP1 Standard Edition(5CAL), FI, S-Chinese [included in price]

  as the operating system, why then I an error like

  The version of Microsoft Windows Server 2008 R2 SP1Operating system was to have 40 GB or 80 GB maximum hard Drivepartition. To solve the problem, please use the links provided.

  choose which hard drive configuration?

  Kind regards

  Once you go to the section "Installation of boot (to Windows (r) OS only) Partition" and select 40 or 80 GB partition error you are referencing disappears.

  Let us know if you have any other questions.

• Change a failing drive - RAID Dell Poweredge H310 - RAID 1

  Hi guys,.

  Thank you for everything that support you in these forums. I'm new here.

  We have a Dell PowerEdge T320 server on my new place of work. It is Dell Poweredge H310 RAID controller on it. It is configured in RAID-1, with 2 discs.

  Now my question is: in the event that one of the drives breaks down:

  1 - I should insert the new drive into the slot where the failed disk has been inserted, or in the following location?

  2 - will be the new drive automatically "copied" with the healthy disk data or it will need some work?

  I read the manual and chapter 'Replacement year Online physical disk', says the following, but I don't know the answer to these questions:

  1. in the management of virtual disks window, select Virtual Disk # and press the arrow key down until the physical disks is highlighted.

  2. press arrow right key to expand the list of physical disks that are members of the virtual disk.

  3. press the down arrow and select the desired physical disk that you want to replace. Press to view the list of operations permitted on the disc.

  4. Select Replace and then start.

  5. tap on the down arrow to select a replacement disk and then press the SPACEBAR to select the disk.

  6. click OK to start the replacement.

  Any advice would be appreciated.

  Kind regards.

  Videoclocknet,

  You must remove the failed disk and replace it with another similar drive on the same niche. When you choose the following location, be sure to follow the steps in the virtual disk management screen (VD) as you have indicated.

  The failed drive will be replaced and the replacement drive will be one on the following location. Either way is perfectly fine. You can then monitor status of the VD and the reconstruction process using OpenManage Server Administrator (OMSA).

  2 disks configured in RAID 1 act as a reflection of the other. Failure of 1 drive ensures that the same data are available on the other. When you replace the failed disk, the rebuilding process begins, and the same data gets automatically copied.

  Please let me know if you have any other questions.

• Dell PowerEdge R510 memory Conmfiguration

  Greetings,

  I have a Dell PowerEdge R510 with a SINGLE processor that currently has 16 GB of slots of RAM installed A1 - A4 are all filled with 4 GB memory modules. My questions are the following:

  1. Am I able to, another 8 GB or memory?
  2. Is only to have a CPU a problems with filling more memory?

  Think I found my answer here:

  en.Community.Dell.com/.../19645918

• Dell Poweredge T 310 - memory problems

  Good afternoon.

  I have a Dell PowerEdge T310 running Windows 2008 R2 server.

  It came with sticks of memory without buffer 2 x 2 GB 1333 Mhz. (4 GB Total)

  I've added sticks of memory 2 x 2 GB 1333 Mhz unbuffered and it worked very well send me a 8 GB of total memory.

  Last week I bought an another memory sticks without buffer 2 x 4 G 1333 Mhz, to make it to the 16GB total, using all six (6) available slots on the motherboard Intel XEON based.

  Now, the server does not start and gives me an error of memory on the front screen.

  If I take 2 sticks, using only the new 2 x 4 GB and 2 x 2GB memory stick the server will start without any problems.

  I'm looking for answers 'why' this will not work with 4 x 2 GB and 2 x 4 GB sticks using all 6 (six) places available.

  I am eager as much memory as possible and use all 6 locations.

  I can buy 6 sticks of memory "recorded", but if that no longer works I hesitate to purchase.

  Any help would be greatly appreciated.

  (Navigation on Amazon, I find a kit of registered models they say will work Dual Rank and having the possibility to use all 6 locations):

  24GB (6 x 4 GB) KIT for Dell PowerEdge series M610 (ECC Registered T310 (registered ECC). DIMM DDR3 ECC registered PC3-10600 1333 MHz Dual Rank memory RAM. Real brand A-Tech.

  ReneWold,

  Question you see specific Udimm. Like the T310 only supports up to four access unique. As seen on page 109. If you were to go to access fourth instead, then would you be able to use the 3 DIMMs per channel, allowing you all DIMM 6.

  Let me know if this helps answer your questions.

• Purple screen of death vmware - Dell PowerEdge R410

  Hello

  I have a few questions on VMware Infrastructure.

  I use two hosts ESXi with ESXi 5.0.Dont have Vcenter Server.

  1. can I update H/W version of virtual machines without Update Manager or Vcenter Server. Y at - there a patch available to update the Version of virtual machines?

  Should I update ESXi host first 5.0 to 5.1, and then update the hardware version of the virtual machines.

  2. I get as a GROUP in a file server (Dell PowerEdge R410) was attached.it happened 7 times before, in the last 3 months.

  Please guide me for these issues.

  Thank you

  Concerning

  Pradeep

  To add to above, make sure you have the latest version of the tools VM installed on your comments before the upgrade virtual hardware.

  You can also patch your host without Update Manager - download patches, copy them to the host and run it from the DCUI;

  software esxcli vib install path_to_bundle.zip d

  I would recommend to patch the hosts first for your do you get the latest version of the tools, then upgrade the tools of the guest, and then upgrade the virtual hardware.

  See you soon,.

  Jon

• Dell Poweredge 2850 and ESXi 4.1

  I have a Dell PowerEdge 2850 with 12 GB of RAM and two CPUs, hyperthreading with 350 GB of disk space.

  This box was initially installed with Redhat Linux ES 5.4 64-bit and OS 64 bit CentOS 5.5 with no problems, so I know the processor supports 64-bit.

  I then installed VMWare ESXi version 4.1 on the Dell Poweredge 2850 with no problems.

  Then, I created a few instances VM I want to install CentOS 5.5 64 bit.  During the installation of a VMware instance, I get this:

  msg.cpuid.notLongmodeQuestionFmt:This veritual is configured for 64-bit operating systems.
  However, the 64-bit mode is not possible.
  Longmode is disabled for this virtual machine.
  For more information, see http://VMware.com/info?id=152
  Continue without 64 bit support?

  Now the question I have is this: given that VMWare is problems with 64-bit OSes comments, how is it that I can install CentOS 5.5 64 bit on this Dell PowerEdge 2850 with no problems.  It seems obvious to me that the PowerEdge 2850 works well with the 64 bit OS but not ESXi 4.1.

  How can I get around this?

  Comments?  Thanks in advance.

  The dell series 8 (1850/2850) have no vt support, so not support 64-bit virtual machine, except 6850.

  The output of the processor shows the same thing, or rather, what he shows no vt in its ability.  It shows lm, long mode, so you can run 64-bit, that you are running ESX, but to succeed in this 64-bit support, you need the lm, you and vt, which you don't have.

  -KjB

• ESXi 3.5 on Dell Poweredge 2950 and Dell 6 GB/s card SAS HBA?

  Hello.

  I'm under ESXi 3.5 u4 on a Dell poweredge 2950 machine.

  I recently bought a Dell Powervault 124 t. autoloader with a HBA SAS 6 GB/s card.

  I installed the card SAS in the PE 2950, but now I can't seem to see in ESXi.

  Can someone help me with this?

  Thank you very much.

  I'm afraid that the Dell technician is correct.

  Someone at - it a link on ESX support not directly connected devices?

  This isn't the issue. The question is: do you have a link that shows devices supported?

  Reference Dell does support the autoloader Powervault 124 t. on ESXi 3.5?

  Have you checked the VMware HCL already, if the SAS controller is included/supported for ESXi version, you are running?

  There are a few articles which have tape readers running with Adaptec SCSI controllers, I don't see anything for ESXi 3.5 with a SAS controller still...

  Maybe there's a better chance to make this work with ESX 4.x with VMDirectPath

  André

• Dell PowerEdge 2850 does not start on a CD of ESXi 3.5

  Hello...

  I have a Dell PowerEdge 2850, who does not start on a CD of VMware ESXi 3.5.  The server works very well with Windows 2000 server.  My first thought to solve this problem was the BIOS.  This is all what I've updated in what concerns the firmware on the box today.

  BIOS - A07

  Perc4e/Di - 5B2D, A19

  BMC Firmware - 1.83, A10

  Here are the latest versions of firmware available from Dell on this box.  The machine starts to start the machine.  But all I see is the first line of text of the CD which is the following:

  ISOLinux 3.63 2008-04-10 Copyright (C) 1994-2008 h. Peter Anvin

  My next thought was that there was something wrong with the ISO image that I downloaded.  I tested it on another machine; has worked like a champ.  Now, I read on a few different posts within the VMware communities that some people have had luck with this question and others did not.

  The inventory number of Dell on the machine is 6HDGS81

  Any advice would be greatly appreciated.

  Some of the Dell CD-ROM may be little flighty. I had hard time to install a CD earlier which worked perfectly well on another machine. I made another copy of the disc, this time burning the CD at a 4 x speed. The installation went perfectly fine afterwards.