Demo of VCS - C VCS-E without license

Similar Questions

• Cisco has any license demo for VCS?

  A way to study, I would test the VCS to my network for a while.

  Cisco has any license demo for VCS?

  Hello

  I think you get very limited (1 x traversal/1 x no traversal) licenses if you have installed the software.

  See also this thread; You can get a limited time license team demonstration license if you ask him nicely.

  https://supportforums.Cisco.com/discussion/11555961/home-lab-VCs-and-TMS...

  Aaron

• Microsoft Word does not produced without license

  Original title: Microsoft does not

  I open Word to type a letter and the stop of the cursor

  On top, he produced without license

  What should I do?

  Review:

  Errors in product without license in Office - desk stand

  also

  Unauthorised product - Microsoft Support

• Enables CLI of VCS for use licenses

  Hi all

  Y at - it a CLI command that displays the current use of the license of the VCS? on appeal, the ridge and the maximum.

  Thank you!

  You can do

  echo "xStatus ResourceUsage | TSH

  at the prompt of the root, which will give the following result:

  ~ # echo "xStatus ResourceUsage | TSH

  Welcome to

  TANDBERG VCS release X 7

  SW release date: 2012 -

  Ok

  * s ResourceUsage:

  Calls:

  Course:

  Current: 0

  Max: 1

  Total: 2

  NonTraversal:

  Current: 0

  Max: 1

  Total: 2

  Registrations:

  Current: 0

  Max: 2

  Total: 3

  * s/end

  Ok

  ~ #

• VCS Starter Pack can be used as VCS-E without any upgrade?

  My client a VCS - C and the TMS, the VCS Starter Pack.

  We rely on the deployment of all in the traditional model.

  What I have to migrate MS full Expressway product or I can leave it as what?

  Can't he do while it is configured as the Starter Pack? This may cause problems later?

  It's my first time with it and someone else put in place before we got here.

  Sent by Cisco Support technique iPhone App

  Hey Michael!

  Of course, you might think the delivery of the VCS-E as a stand-alone box with a crossing area and

  SIP proxy VCS - c

  I can't recommend this doing.

  If I see just the starter pack is just an extra key, giving you all the options you need:

  0 calls no course, 5 calls route, 50 entries, 900 ROUND relay, Expressway, encryption, FindMe, Starter Pack. But it also means that you are linked to this feature set (for example, you can not delete the provisioning, findme,...)

  Some other limitations I see:

  * officially VCS-SP-E cannot be added to the TMS, then you miss the detail records management calls...

  * the starter pack provisioning can hinder the supply of MSDS if intended to be used

  * TMSPE/OpenDS (also password "local-tms' database (authentication)) will not work on the VCS-SP-EP

  There could be more.

• Sourcefire without license

  Dear team,

  When I added the ASA5515X-FPWR-K9 model to my (DC) FireSight, I received unlicense on my product, while my DC already add TAMÁS.

  When I go to the devices--> Device Management--> showing as unlicensed product (the case as I already added all the licenses in DC)

  but when I try to edit (in devices) but still, I am not able to check the licensing part it contains.

  Please find the attached screenshots for reference.

  Unlicensed.jpg

  

  unlicensed - 1.jpg

  

  license - details.jpg

  

  Help please give me some advice.

  Thanks in advance,

  Mr. Mistry MILIN

  There is no license for a 5515 in your screenshot. You need to apply a license that matches your platform of firepower to the MC FireSight.

• BlackBerry smartphones I don't have an email account only a business without license password,.

  How I take the password to activate, if I can't contact the Admin, some necessary tips... installation enterpise is free? What are the conditions required, and I want the step by step procedure to install the software of Enterprise Server, Enterprise Server software tries to recover the password for activation?

  Mobile provider and the carrier = the company you need in the operative part of the SIM card.

  Call them and find out about the BlackBerry data Plan THE... not a generic data plan.

• Update FB4.5.1 Premium for PHP does Zend Studio without license

  

  I got this error when launching after update. I bought this from Adobe. How can I fix it?

  I tried to disable FB4.5.1 Premium for PHP and also CS5.5 and

  Re-enabled FB4.5.1 Premium for PHP but it will not solve the error message.

  BTW: the link in the error box is broken.

  Phew. The first resettlement gave me an error after installing the update... involving the workspace and came out after the error. Then... I uninstalled again and then manually remove the directories in the workspace.

  I then reinstalled and then the update worked.

  PS: disable cs5.5, if you need to reinstall.

• Cisco Telepresence Server/Cisco Telepresence driver/Cisco VCS - C / Cisco TMS license

  A big problem with the fact that I'm stuck is licensing. Really, I have tried many things to find the solution for it, but could not.

  I have actually made all of these servers (mentioned in the title) in my lab in preparation for the CCNP Collaboration certification at home.

  I am not able to complete some laboratories due to license issue (I guess). Y at - it an option to get the demo license for all these servers?

  I would be really greatfull if someone can suggest me the solution and/or the licenses required to complete all the stuff for my CCNP Collab tag.

  Best regards

  Dipak Singh

  TMS and VCS - C when installed without licenses, are automatically set mode of demonstration/test with some availability of license to test with. If needing a VCS-E, you will need to do to your account manager and they should be able to get you the time limited licenses good because I think that 90 days.

  Conductor Essentials is free, which means that you can install and get full functionality without the need of all licenses, but you are limited to 1 conference bridge and no grouping is allowed.

  TelePresence Server require licenses to function, once again, reaching out to your account manager for this.

  At the end of the day, you should reach to your account manager for all of this, as they should be able to help get timed license if you need.

• License of VCS & MSDS

  Hello world

  I need to clarify some doubts with permission of TMS and VCS:

  Our customers need to add endpoints SX20, the customer already has a deployment of TP with TMS, VCS Expressway & control, MSE8510.

  I have two options:

  1 - save the SX20 endpoints in CUCM and use of TMS for planning.

  -The permit required for CUCM 9.x: R-UCL-UCM-LIC-K9 (LIC-TP-9 X-ROOM)
  -The permit required for TMS 14.3.1: L-TMS-SW-PAK (LIC-TMS-100)

  2 - save the SX20 endpoints in VCS and use of TMS for planning.

  -The permit required for TMS 14.3.1: L-TMS-SW-PAK (LIC-TMS-100)
  -The permit required for VCS X.7.2.2: L-VCS-PAK (LIC-VCS-100), I'm not sure if I need this license for firewall VCS non-traversal?. If each SX20 is registred in VCS is not necessary this kind of license, right? Will be requerided if I need SIP-H323 o IPv4-IPv6?

  Could you please confirm if I'm wrong? Y at - it another option? Do I need other permits?

  Any other comments are welcome.

  Thank you

  Pablo

  Hi Pablo.

  If you add just additional end points, the easiest way would be to add to the existing deployment (option 2 above) rather than adding additional complexity with CUCM (option 1).

  According to the license on the current deployment, you may or may not need to purchase additional licenses.

  (1) to check their existing TMS to see if there are licenses available system (this is shown on the display main portal when you open a session (near bottom of box to the left).  If you need more, you can buy them - you don't mention how you add - but you can buy them in smaller than 100 packages if you need (IE a L-TMS-25 is 25 licenses of system).

  (2) check the VCS control the number of licenses currently installed (they are once again, on the first screen get you when you open a session).  Check the license limit and of leading figures - that should give you an indication as to the relevance any more necessary or not (that is to say, if the vertex figure is not closer to the limit, you will not need to buy more).  Again, you can buy them in containers smaller than 100. They allowed to 'simultaneous call', so you generally do not have one for each device.  If all calls are within one organization on the VCS, Non-Traversal licenses, you will need on the control VCs.

  Let us know how you go, or if you have any other questions.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Profile C40 with VCS Starter Pack Expressway system

  Hello guys,.

  Customer not want options like Firewall and the Conference (MCU 5300) crossing.

  But as this is a small script (there around 2 profile C40 + 2 SX20 10 video Jabber), I found that it will be interesting using VCS Starter Pack Expressway. He's no more than 50 records or 25 route calls as shown in the data sheet 'support '.

  I took a look at the topis here and also some documents and say that C40/SX20 are not supported for the supply, but since the SIP/h.323 support, calls should work perfectly.

  No doubt: that the client will lose in terms of features or benefits without the support of this commissioning endpoints?

  It would be a pain in the neck to enter the SX20 or C40 to VCS Starterpack expressway?

  http://www.Cisco.com/en/us/prod/collateral/ps7060/ps11305/ps11315/ps11337/data_sheet_c78-697075.html

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/VCs/config_guide/Cisco_VCS_Expressway_Starter_Pack_Deployment_Guide_X7-2.PDF

  Thank you!

  Alan

  Olá Alan, respenderei em inglês para fica na don't base dados, mas design sao best respondidas send any video Business forum.

  About your 3 points, depends on:

  (1) even if you deploy the TMS, endpoint will try to get the directory using HTTP/HTTPS connection. If the endpoints are outside / internet, it may be refused by security reasons.

  (2) you can always configure auth on the StarterPack VCS to auth against the local database. At the endpoints configured manually, you can enter the identification information.

  (3) you can configure the bandwidth on VC (subareas or pipes) configuration control or limit directly to each endpoint

  The SX/MX/EX/C series can register the StarPack using a direct connection (h.323/SIP) or behind the FW/NAT using H.460.18/19 or assent. They can local Auth VCS DB. Be aware that the VCS S is usually installed in an external DMZ or directly with a public IP address. In this case, if you have 2 x SX to the internal network and the VCS at the DMZ (with NAT in the middle), all media will be hollow VCS, even if the two SX are on the same subnet.

  PS: Be careful where to include the VCS. If you use NAT on the VCS, basic network license need double.

  It will be useful.

  Concerning

  Elter

• VCS DISCONNECTION PROBLEM

  I have assistance who need the situation on VCS running X7.2 version.

  I can't kill a call that was for days... When I try to disconnect there. When I look at details is States 'cancellation', but does not die.

  Any ideas... The call comes from a neighbor, I put in place with other VCS.

  I haven't restarted the system in more than 196 days.   I have a few other calls via the old 20hours and they specify also (cancellation).

  I also called the site hosting the other VCS and without registration it has do with the information I have on my VCS.

  Ideas also if I SSH in the area what is the command line syntax to perhaps force disconnection it?

  We saw the problem similar and same weird outdated records. A reboot of the VCS solved the question - of course, this is not ideal, but it only a computer!

• The double option of VCS Starterpack Interface!

  Dear all,

  We have a demo system VCS Starterpack with CTI-ATP-VCS-SPAKK9.  I did a software upgrade to X7.2 of X 6.

  Now, I want to use the functionality of Dual Interface and NAT for demonstration of customer but I noticed that there is no Option of Dual Interface on the demo product.

  I tried to find the order ATP for Dual Interface code, but there is not as an option for the product code of CTI-ATP-VCS-SPAKK9.

  What should I do? Does anyone have the same problem?

  Best regards.

  OZBAY Tamer

  Hi Tamer

  You can open the DI for VCS SP option.

  L ATP-VCS-PAK

  -Top level SKU for your VCS StarterPack

  BR Oleksandr

• Reboot and planning of Maintenance - VCS

  What is the Cisco recommended VCS calendar maintenance and reset for VCS?

  Such as: it is worth to restart these monthly, daily, weekly, and monthly backups quarterly?

  Nothing seems to be mentioned in the deployment guides or admin.

  Any help would be appreciated!

  Hi Paul,.

  No, as I know he has no recommendations for safe and fully operational VCS (VCS cluster) and it is very unlikey to find a.

  You can keep the VCS permanently without having to schedule a reboot "just-in-case".

  In very rare occasions, when the TAC is a problem, as the leak of memory, for example, you might advised to restart every X days/weeks on the outside of VCS affected office hours, until the development arrives with fix. But once again, which is very rare and should be performed according to the recommendations of the TAC only.

• change the VCS - C to VCS-e.

  Y at - it can change Cisco VCs control works like a VCS motorway via an additional license?

  Jens,

  the license key will change from a VCS C a E but understand that VCS C holds licenses of crossing that you lose, and you will need to buy at least 5 for the VCS E. Also your licenses not traversed can be lost.

  An approach that can work for you is to buy a VCS E virtual machine.