DESIGNATION OF THE USB

Similar Questions

• Port Replicator III + very high CPU when you move the usb mouse only in W2k

  Tecra M2 with a port replicator III +.

  It is set to dual boot XP and Windows 2000 (yes I know it is well a bit but I have a bunch of stuff installed in win2k it is difficult to find these days).

  XP is very good at 100%, but with win 2000 if I use my * USB mouse * on the * ports port replicator and waggle the mouse around - the * CPU * jumps from 0 to * 70 + % * use (System process that seems indicatates like IRQ problem). If I plug the mouse into the ports of the laptop (when the laptop is connected) - it's fine, no more than 5% cpu usage. It's a microsoft basic mouse. I really believe that this is a problem of usb any, because the cpu jumps a little if I type quickly on my usb keyboard (only a few %). It comes with the usb ports on all the Replicator.

  Any ideas? I don't really want to plug my mouse in the morning because it beats a little interest to have a docking station in the first place! I have installed mobile extensions. All other aspects of the replicator are fine

  Martin

  Huh it will not be easy to find the right explanation for this.
  At the moment when Tecra M2 has been offered on the market as Replicator port compatible Toshiba offered Toshiba Advanced Port Replicator III (no +) and at that time both supported in operating system has been tested with it.

  Toshiba later designed Toshiba Advanced Port Replicator III + and confirmed the compatibility with Tecra M2, but obviously with more recent WXP (at this time).
  So now, you've been following situation: you use most recent Replicator port, but with much older operating system so I assume that there may be a compatibility issue with W2K.

  I can't imagine use you so often with W2K and if so, may not be so problematic to connect the mouse directly on the cell s USB port.

  Sorry, but I don't think that there is nothing you can do about it.

• generate a digital triggering out CH1 (low and high) for the USB-5133

  Hello

  I would like to generate a digital triggering on the USB 5133 CH1, is this possible?  I tried with the PFI 1 successfully but the output is only 3.5 v and I need to 5V, because this trigger signal goes to a box of pulse generates a signal, which is received by the CH0 on the USB-5133. This configuration works on the 5102 OR but because of the treatment, I am obliged to try a new device.

  Channel 0 and 1 are only entries then you will not be able to use them to generate a signal.  All of our products current digitizer that are recommended for new designs use 3.3V CMOS logic levels for PFI lines in output mode.  Your best bet to generate a digital triggering 5V would be to use an external buffer that can accept 3.3V CMOS levels as an input, but is under voltage of 5V.  Here are some that might work for you, but there are many others: http://www.onsemi.com/PowerSolutions/product.do?id=M74VHC1GT126DT1G adding a buffer in line with the trigger signal will add delay, so you will need to ensure that it is acceptable for your application.

  Hope this helps,

  -Matt

• Can you produce arbitrary data TX with the USB-8452 SPI streaming mode?

  I use a USB of NOR-8452 controller in SPI mode, controlled by a C program compiled in 2013 of LabWindows/CVI. In order to talk to the chip, we designed, I need to control the delay between the final of SPC deassertion and the CS deassertion (T11 synchronization setting) to keep it very small. Therefore, I use streaming mode.

  I read the NOR-845 x Hardware and software manual and looked at the two projects that use the SPI in streaming mode in NOR-845 x examples dir. The examples use two REITS it to talk about the A/D converters. In other words, variable data in time comes from the SPI (ADC) slave to SPI master (Controller NI 8452) via the SPI_MISO line.

  Is it possible to use the USB-8452 to generate variable data in time that goes the other way, from the master to the slave SPI via SPI_MOSI SPI line? Can I make a burst of arbitrary length entry using the streaming mode?

  For example, let's say I have 8 bytes of data to be transmitted:

  WriteData [] is {0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08};.

  If I try to send this as 4 samples of 16-bit:

    

  ni845xSpiStreamConfigurationSetNumBits (StreamHandle, 16);
  
  ni845xSpiStreamConfigurationSetNumSamples (StreamHandle, 4);
  
  ni845xSpiStreamConfigurationWave1SetMosiData (StreamHandle, WriteData, 8);
  
  ni845xSpiStreamStart (DeviceHandle, StreamHandle);

  I expect to see transmitted:
  

  0 x 0102
  
  0 x 0304
  
  0 x 0506
  
  0 x 0708

  Instead, what I see in fact is the first NumSamples times repeated word:

  0 x 0102
  
  0 x 0102
  
  0 x 0102
  
  0 x 0102
  
  

  Is it possible to generate the first (non-recurring) model? Or streaming mode really is only able to capture input data?

  Thank you for any help you can provide.

  -jskroch

  Hello jskroch,

  I looked through the documentation for the NOR-845 x and it confirms that the workflow capability displays the same MOSI data for each operation of SPI during streaming.

  You can use the ni845xSpiWriteRead function to write a byte array in the order using 1 function call.  These bytes can be configured to your waveform specified.

  Kind regards

• Ground and the USB-8451-> it should reference?

  I use a usb-8451 attached to a PCB card which has its own means with separate analog and digital designs. When I join the 8451 grounded strange results of power supply occur. Is it allowed to leave separate and unconnected?

  Devices USB usually get their power supply (+ 5V and GND) of the device, they are connected. There is no need of additional connections to GND. These additional connections can lead to "mass loops" that can pick up noise and cause errors. -The 'front end' of a device properly designed USB is isolated from the power supply. If you connect anything to the input of the USB device, use the GND or NOT the entrance terminal, of reference and NEVER the Terminal GND of the Board that powers the USB device.

• Upstream 13: make a copy of the USB of computer image 13 Stream

  It has come to my attention that the image USB copy that I compiled may not be usable as a way to reinstall windows 8.1?
  I learned that the Scandisc USB flash drives which I used are not designed as a way of copying and for the resettlement of same OS if the disk image I can say copied ok. This has now been confirmed by Scandisc. The question is now how do I make use of the unique copy of my computer image I have on my flash Scandisc disc and what USB memory keys are designed to provide a useful computer image copy?
  I hope someone can advise me on this.

  First of all, make sure that you start from the USB port. On the portable stream you constantly hit the ESC key when you turn it on to bring up the BIOS Menu in the upper left of the screen. Choose Boot Options then choose USB Flash Drive and it will boot to a screen that says select your keyboard type.

  On mine US is by default I chose that.

  Now, click on the button problems. Click Reset your PC.

  Select the target operating system. Windows 8.1 should be there. If it says Windows 10 and you want to come back to win 8.1 choose it anyway.

  Then, after clicking on the target operating system you will see a screen that says: 'This is what will happen', click Next, and then click YES, repartition the disks.

  Make sure you choose the option in the final stage, which said just delete my files. Do not select the option completely clean.

  Wait 45 minutes and your system is restored from the factory.

• Wusb300n adapter not recognized by the USB port

  Cannot get WUSB300N adater to install on XP Pro SP3. The problem is with the USB port in recongised in the Design Manager. It appears as a "unknown USB currency" as a USB controller and not as a legacy of network. A Linksys support remote control my PC but not able to get to install connectly. Tried all the USB ports. Tried to install Design Manager.The motto is fine recongised by my other Vista PC. ? Is there a problem with my USB ports? Card mother MSI KT3 Ultra-ARU , I think that the USB is 1.1 not 2.0 but it is within the specification of Linksys for the WUSB300N. Install a new PCI USB2.0 card will it heal? Comments please. (I know the MSI motherboard is old, but is simply a 2nd bedroom based PC)

  Resolved issues. New USB 2.0 card and drivers installed. It will not work with USB1.1 or it would ' t for me. The sheet he says OK with

  IEEE 802 standards project. 11 b, IEEE 802. 11 g, IEEE 802.11n, USB

  1.1, USB 2.0

  Ports USB Port

  It works with USB 2.0 but not USB 1.1

• WiFi radio adapter off, the USB ports does not and the Bluetooth adapter is no longer visible... Please help!

  I had my laptop Dell Vostro repaired under insurance in January 2013 after a spill of liquid.  HAAC Ltd. has replaced most of the laptop - but the return, the SD card did not work.  This seems to be due to the engineer he connects not properly and the company recommended it and returned it to me again.  A couple of months, I found my USB was temperamental - so is my built in Bluetooth adapter.   Last month - the wifi does not work for most of the time either so I have to connect to my router by wire.

  This could be a problem in windows 7 - all my problems seem to be related to network adapters.  If it's a hardware problem - does anyone know if it could be another loose connection?  HAAC Ltd. only give a 3 month warranty on parts that seems just a little.  But if this anomaly is due to the production of poor quality - that is not properly connect the laptop then I'll go back their again if they are responsible.

  By the way – there's a switch wifi on the front of the laptop - but is not currently be recognized.

  If anyone has settings that I could check that can help - especially if some inhibit the use of wifi.

  Thank you very much

  Hello

  Your wifi switch not recognized is probably a hardware problem. The rest could be a hardware or software problem.

  Method 1:

  Lets start by doing a reset to coercive. Follow these steps:

  1. Unplug the notebook (remove power cord), then remove the battery.
  2. Disconnect all USB devices and the connections between the USB ports.
  3. Let the laptop only for several minutes.
  4. Then plug the power cord without connecting the USB devices. Then replace the battery.
  5. Plug each device in turn, allowing them to load the drivers of devices one at a time (plug in the appliance and wait its loading all its drivers before installing the next USB).

  The computer recognizes the USB ports? All of them or none of them?

  Method 2:

  Open Control Panel, Manager of design. Click the view tab, and then click Show all devices. From there, you can remove all instances of USB devices and restart the computer to see if the problem resolves. Repeat this procedure with the wireless adapter (uninstall and reinstall, ensuring that there is only one instance of the wireless adapter).

  Method 3:

  Create a new user account by following the instructions in this article:   http://windows.microsoft.com/en-US/Windows7/Create-a-user-account . Does this solve the problem?  If the problem is resolved in a new user account, this means that the old user profile is damaged. Here is the link to repair a damaged user account: http://windows.microsoft.com/en-us/windows7/Fix-a-corrupted-user-profile.

  Try these methods and post your results here. I'll be here waiting for the results!

  Kind regards

  BearPup

• LaserJet M1132 - scan not possible when it is connected to the USB of TimeCapsule airport port

  Hello

  I'm on Mac OS X Lion 10.7.4

  Installed the latest drivers to date: 1.2

  The multifunction printer is pluged on a TimeCapsule 7.6.1

  Printing works fine.

  But scanning is not possible using "HP Director" and with a brand like HP, I expect to have drivers with the message box from standard scanning Mac OS X (Capture of Image and therefore all software that use this API in the operating system).

  This works very well with a printer of a different brand.

  Is there a solution?

  Thank you

  Well Yes, by design, the USB port on the airport take in charge of printing, not for analysis or fax.  I'm sorry.

• where can I find the usb drivers to connect Rikomagic MK802 to my W7 machine?

  Hei.

  Someone who knows where I can find the usb drivers to connect Rikomagic MK802 to my W7 machine?

  John.

  It does not seem to be designed to run on a PC as it is an Android PC in its own right...

  http://store.cloudsto.com/rikomagic.html

  "This size micro computer can be used easily by simply plug into a TV with a spare HDMI slot and then connect a wireless keyboard/mouse. It allows you to do everything you can do on your PC or tablet like browse the web, check your e-mail, go on facebook, watch HD movies, listen to music and of course much more by installing thousands of apps now available for Android. »

• KDL-42W700B giving power to the USB port in standby mode

  Hello

  My new KDL-42W700B giving the power to the USB ports even mode standby.

  I connected internet USB dongle and when I exit tv, as its getting power internet connectivity continues.

  Called the customer service about cela and they claim that TV sends power to ports USB is the characteristic of the TV and Sony engineers designed this so.

  I've not seen such lame feature anywhere in any model in other brands, but also Sony models too.

  I checked the earthing of the power outlet power. Its perfect.

  Is this a problem with my TV or something else? Please give me the solution

  Thanks in advance

  Bharath

  It does not occur for other models

• iPhone 7 will not play audio via the USB port on the car.

  When I plug my iPhone USB port 7 more in my car (15 Jeep Grand Cherokee), the artist/song/podcast information appears on the screen, but the sound plays through the speakers of the phone.  I have confirmed that my settings are all the same as they were on my 6s, who played without any problems via the USB connection.  Bluetooth streaming works fine - no problems at all.  Any ideas, or is this a problem similar to that people have with CarPlay?

  Welcome to Apple Support communities, kevo.mac!

  Congratulations on your new iPhone 7 more! I see that you connect with your Jeep Grand Cherokee using the USB port. Everything seems to work fine, except that the music plays through the phone instead. I'll be happy to help you to get this working.

  Help to connect your iPhone, iPad or iPod touch with your car radio

  If you are using USB playback

  Restart your iOS device and your car.
  Connect your iOS device to another stereo USB port (if you have one).
  Try another USB cable.
  Update your iOS device.
  Install the updates to the firmware of your car radio.
  Test of audio playback from a different application. If you can not play audio from a specific third party application, contact the developer of the app for help.
  If you can not play audio from an app Apple, contact Apple technical support.

  Enjoy your weekend!

• Is there such a thing as a USB wireless, that does not need USB cable upstream that goes into the usb slot in the main computer?

  Is there such a thing as a USB wireless, that does not need USB cable upstream that goes into the usb slot in the main computer? I've looked everywhere but I can't find one. I hate the son, and I try to clear my desk of as many people as possible.

  # USB is cable only.

• MacBook retina cannot find the USB hard drive when it is plugged again

  Hello world

  I have a MacBook retina 2015 computers and a hard drive WD elements USB3 that I use as a Time Machine backup when they travel. The drive is plugged into the USB - C through one of the Apple dongles and when I first start the computer, the USB is mounted and that it appears on the desktop. He does everything very well.

  When I want to take the machine away, I eject it, wait for the secure message and then physically disconnect the drive. However, when I go back and reconnect the drive, the Mac did not see it. The reader will be able as the light comes on and I can hear it turn. Just, it is not mount and is completely invisible for MacOS.

  I checked all connections, even used another dongle - no luck. A disconnect does not set, and I tried to reset the NVRAM. So far, the only solution is to reboot the Mac, afterwards the player reappears - at least until I need to unplug it again.

  Anyone got any ideas what is underway and if there is a fix?

  Thank you very much

  Mike.

  Hello, Mike Richards2,.

  Thank you for using communities Support from Apple!

  This is I think understand that you are not able to see an external hard drive when it is ejected, and then reconnect the computer.  I have some suggestions that I hope will help you.

  It is important to try to isolate what is responsible for this.  The first thing to do to help isolate what is causing the problem is to start the computer in what is called Safe Mode and see if the problem persists.

  Start in safe mode:

  1. Choose the Apple menu > shut down.
  2. After your Mac stops, wait 10 seconds, then press the power button.
  3. As soon as you hear the startup tone, hold down the SHIFT key.
     You must press the SHIFT key as soon as possible once you hear the startup tone, but not before.
  4. Release the SHIFT key when you see the gray Apple logo and progress indicator.

  OS X El Capitan: start in safe mode

  Once the computer is running in safe mode, see if you can duplicate the issue.  If the problem does not appear, go ahead and try to reboot normally again.  If the problem has disappeared, it may have been caused by a problem of file or directory of cache fixed by booting in safe mode.

  If the question comes up, you'll want to check the login items.  Follow these instructions to remove the connection:

  OS X El Capitan: If you think you have incompatible connection points

  Remove the connection, restart the computer and see if the problem persists.

  Have a great day!

• Content of the USB accidentally in the trash can

  Some how I accidentally placed the entire contents of a USB drive into the trash.

  Whenever I insert the disc, its contents appear in the trash.

  I don't want to delete the contents of the usb drive.

  How can I delete the contents of the trash and keep it on the USB key?

  Kind regards...

  Open the Recycle Bin and drag the files from the disk to another location on it.

  (144143)