LaserJet M1132 - scan not possible when it is connected to the USB of TimeCapsule airport port

Similar Questions

• HP P1102W does not print and does not open when it is connected through the USB port on the road

  I bought this printer and I set it with a fixed IP address. After a few months, he has simply stopped working. So I decided to connect to the console and I wasn't able to do it either. I printed the test page and the ip address is 0.0.0.0. I, then, tried to plug in the USB cable on my computer and the drive that contains the software, it does not appear. He is a second and then disappears.

  I would like to get a solution to this problem before I throw this piece of 'material' on the discharge.

  Thank you!

  The 1102W uses what is called USB wireless.  The installation of the printer is the only way to recover the printer on a network in this case.  There is no place to set the IP address without getting a DHCP address first, which is not the case here.

  First, retrieve the default network printer.

  Restore the default wireless settings.
  a. turn off the product.
  b. press and hold the wireless switch and the
  Cancel button and then turn on the product.
  c. hold the button until all lights flash in unison.
  and then release the keys.

  This should reset the default settings of the network.

  Then, uninstall all the software of the computer printer.

  Reinstall the printer from here click on software and Driver Downloads and select your operating system.

  It will take a computer on the same network and USB cable.  Click network installation and connect the USB cable when prompted.

• Elite 8100 desktop HP will not start when it is connected to the USB hub

  HI, I have a problem with USB HUB (US221A, 2PORT USB 2.0 SWITCH) - powered by the computer.  If the USB port is connected to the start the PC hangs at the HP logo screen - nothing works.   If I press F9 during boot error 43 occur.

  Looking for abios update.

• Windows 7 does not recognize that a Canon canoscan 8000F is as a device when it is connected to the USB port.

  Windows 7 does not recognize that a Canon canoscan 8000F is as a device when it is connected to the USB port.  Tried unplugging, reboot & reconnect, in different orders, but the computer does not recognize there is.  Tried to install a European website for Canon driver: Scangear CS, 8000fvst8120a_xpen.exe, which is advertised as compatible with Windows 7.   But the installer does not work.

  Windows 7 Professional 32 bit.

  Hello Graboots,

  Thank you for your message.  You can plug your printer on another computer, in order to exclude the possibility that the problem lies in the printer?  You can try using a different cable, for this rule as well.  Since it is a question of recognition, we remove the external devices before software troubleshooting.  Do you get anything when you plug the printer (ie. a tinkle of connection)?  Please let us know, we are looking forward to hear back on your part.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Sound does not work when it is connected to the TV with HDMI

  I have a HP Pavilion Notebook PC, DV7 - 6813EV, running windows 7 Home Premium 64-bit SP1. My problem is that I have no sound when connected to my TV HDMI connection and press. Please could someone help me? Thanks in advance

  Hello gematz,

  The sound does not work when it is connected to the TV via HDMI.

  Go to start.

  Type sound.

  Click sound

  On the playback tab, click with the right button on the HDMI interface, and then select set as default device.

  If you do not see the HDMI, right click and select devices see off, then set as default.

  I would like to know how everything goes.

• Service Pack 3 for Windows XP does not recognize that it is connected to the USB ports. I get a notice that something has been plugged, but Windows fails to recognize regardless of the question.

  Service Pack 3 for Windows XP does not recognize that it is connected to the USB ports. I get a notice that something has been plugged, but Windows fails to recognize regardless of the question.

  Disconnect all USB storage.

  Run this tool by do right click and choose 'run as administrator '.

  Of course, all first extract it:

  http://www.Uwe-Sieber.de/files/drivecleanup.zip

  If your XP is 32 bits, use the Win32 folder.

  Reset.

  If you still can't find the drive, assign it a drive letter in disk management.

• Help and Support does not work does not correctly when you are connected to the Vista administrator account

  Click the startup of Vista and in the Search box , type WINVER , and press the Enter key on your keyboard.  Please report back with the correctVersion number and build shown . Carey Frisch

  Version 6.0 (Build 6002: Service Pack 2)

  I have the same problem exactly as described Flashimator don't except this: the problem occurs only when I am logged into the administrator account.  Support seems to work normally in my user account.

  I should add that my HP laptop has an OEM program which seems to be an overlay on the Windows Help.  It is also not available in the administrator account.

  (HP Pavilion dv9260us, Vista Ultimate x 64, Intel Core 2 Duo T7200 @ 2.00 GHz, 2 GB RAM)

  Thank you.

  PS It is often more important to have help available when logged in as an administrator as I do only when I have to (as in the resolution of problems).

  Hi Dyn0saur,

  Thanks for visiting the site of the community of Microsoft Windows. In order to focus more on your particular situation, I'll split your post into a new thread.  Son of splitting are made to mitigate the confusion caused by more than one display on similar topics, which allows us to focus on each client individually.

  Regarding your question, see the article following some possible troubleshooting for your question:

  http://support.Microsoft.com/kb/917607

  In addition, an article on content help:

  http://Windows.Microsoft.com/en-us/Windows-Vista/get-the-latest-Help-content

  Thanks for visiting the site of the community of Microsoft Windows.

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Subvi value not updated when it is connected to the connector pane

  I have a legacy program that computes a frequency when a value changes of sensor (falling edge essentially), and I'm trying to convert the logic to a Subvi, so I can use it for 44 other sensors. The program first used a large number of property value node, I discovered is not good for subVis. I converted them to local variables, but I still have questions.

  As soon as I connect something to the output pane that closes the update value question. If I remove the connection in the connector pane, it works fine.

  a picture of the block diagram is attached. I tried to connect Freq and frequency of output to the connector pane, as soon as I connect it to the component connector to work properly to date do not at all.

  The VI is configured as non-reentrant.

  Thank you

  
  

• CarPlay audio quality of the voice when it is connected through the USB port is poor vs Bluetooth on Pioneer AVH-4200NEX

  Hello!

  I recently installed a Pioneer AVH-4200NEX unit, I was super excited to improve my car with the support of CarPlay, and everything works great except for one thing.  When I connect my iPhone (6s +) to the unit via a USB cable and a standard phone call, the audio quality is very bad - hail, very downsampled, and metallic sounding compared to the use of Bluetooth via the unit to pioneer for the same phone call (I'm on LTE, using HD voice, although the quality difference is quite noticeable on the calls not HD and on the 4 G calls).  I looked for an answer to this question, but the best that I can find mention of limited USB bandwidth and try to juggle than the bandwidth for the rest of the CarPlay experience, although I don't buy not because audio via the iPhone connected with USB playback is just as clear that it is through Bluetooth.  So my question is: How can I submit a bug report Apple about this behavior and (b) do you have other CarPlay users also be known this recent problem on a unit of Pioneer NEX (AppRadio included)?  It would be great if this is a bug of Pioneer for which they can release a firmware update, I'm just worried that it is a codec problem specified by the CarPlay, so non repairable.

  Thank you!

  -Seth

  Hello served,

  Thank you for using communities of Apple Support.

  I understand that when you use the USB cable for your iPhone in your car with the audio CarPlay is mediocre. I know how it is important for you to hear your calls clearly. In a situation like this, I recommend the steps described in the following article to help solve the problem.

  Configure CarPlay to use with your iPhone

  Specifically the section to get help:

  Get help

  If CarPlay does not work as you expect, here's what you can check. After each step, try to use CarPlay again.

  1. Make sure that Siri is turned on.
  2. Restart your iPhone and your car. Depending on your car, you can see the CarPlay home screen when you turn it on. If you do not, look for the CarPlay logo on the screen of your car.
  3. If possible, connect your iPhone to a different USB port in your car.
  4. Try a different lightning to a USB cable. Make sure that the cable is certified.
  5. Update to the latest version of iOS.
  6. Check the manual using your car. You may need to install updates of firmware for your stereo.

  See you soon

• WHY MY USB DOES NOT SHOW WHEN IT IS PLUGGED INTO THE USB PORT?

  I use my USB key, windows7 ultimate 32 bit is not show I have uninstall all and restarted my computer (laptop), but still does not work, I downloaded some readers but still does not he continues to show me this in Device Manager, I have used several USB but it still doesn't work do not? I'm going to enjoy anyone who helps a lot thanks

  

  Hi Ali,

  Thank you for the update.

  I suggest you to run the next Fixit and check the status.

  Automatically diagnose and solve problems with the equipment. (USB) Keyboard and mouse are not detected by the Manager of devices or when they do not work.

  What it fixes:

  • When you install a hardware device, it is not detected
  • Determine if your audio device is plugged
  • The driver updates are not installed automatically by Windows Update
  • You receive one of the following errors:

  Click on run Fixit.

  Please let us know the State.

• Satellite C660 does not start when it is connected to the battery

  Satellite C660. I can only start with the battery disconnected and connected charger.

  Since when you noticed this problem?
  Is the battery that you always use original one you have with your machine?

  When Windows is fully charged and you put the battery in addition is recognized correctly battery?
  What happens when you unplug the AC power supply

• ZTE open not light unless it is connected to the USB power source.

  Even with the battery fully charged, my ZTE open never turn on unless it is connected to a USB power source. Once connected, it can be started, behaves normally and can be disconnected.

  You should contact the owner of the eBay store in this case.

• computer not automatically standby (formerly titled "impossible computer automatically sleep when it is connected to the internet with modem cable")

  Hi, I noticed recently that my computer (Windows XP Media Center Edition 2005) is unable to sleep automatically when it is connected to the internet with a cable modem. Change the settings for my current power mode and try a different feeding regime (diagrams of Windows XP default power and power management, I created) only solves the problem for 2 days at most. I also tried to change the settings for the other power plans mentioned, and yet once again, the problem was only set for two days at the most. I also tried turning off my computer, restarting my computer, recording Powercfg /Restore Default policies in Run, saving sfc/scannow in Run, and again, I got the same result. Reset and power cycling the modem cable is not helped either. To help you better understand the problem, for example, if I had the date set for the screensaver set to 1 minute, the time for the monitor to turn off set to 2 minutes and time for your computer set to 3 minutes, the screen saver activate after 1 minute, the monitor turns off after 2 minutes, but the computer would not sleep mode after 3 minutes , even after an hour or more. I tried to check the Task Manager, and I have not noticed any process that would be interrupting the day before. However, I noticed that when I turned on the monitor by moving the mouse, even when the computer was unable to sleep and unplugged the ethernet cable from the cable modem and waited, the computer has entered standby as it should have.  I tried to find a solution for more than a week, contributions for this issue would be greatly appreciated. Thank you for taking the time to read my post. (Update: it seems that the problem is something else then my cable modem.)

  Hello

  Thank you for the update.

  This behavior can occur because of possible conflicts of third-party software, which includes the third-party security software.

  You can also temporarily disable third-party security software and firewalls installed on the system and check the issue.

  If disabling the antivirus software solves the problem, you may need to configure the settings of the antivirus as a result program. Please contact the software vendor for assistance in this regard.

  Note: be sure to enable the security software on the computer after checking the issue.

  Note: When you perform a clean boot, you can activate services for the modem, network card and disable third-party services to check the issue.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• Why always, I received management is not available when you use maps for the iPhone 6 and I live in the Qatar?

  Why I always get direction is not available when you use maps for the iPhone 6 more?

  Currently I live in the Qatar.

  Hi Alison, Sameh

  The reason why you see directions is not available, it's that for cards of Apple, turn-by-turn directions is not a feature that is available in the Qatar. You can search for places and satellite imagery
  Take a look at the link below for more details on what features are available in the Qatar.

  iOS 9 feature availability
  http://www.Apple.com/iOS/feature-availability/

  Nice day

• Here's a strange. I have a HTML page with this time a wmv video. It works perfectly from a USB stick or SD card, but does not work when they are copied to the hard drive

  I have an HTML page created with web expression 4. It contains only a wmv video. It works perfectly when it is called from a USB stick or SD card, but does not work when they are copied to the hard drive. The results are the same with IE and Firefox. It don't make no difference if I use Media Player V9 or V11. He has no control on the page Media Player. Video and html files are in the same directory. Here is the code snippet:

  LIFT, DRAG, THRUST and GRAVITY

  
  

  
  
  

  If I run it on a machine with Win 7 there is no problem.

  Richard Grosser

  Hi Richard c. Grosser,.

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Microsoft Expression forums.

  http://social.expression.Microsoft.com/forums/en-us/categories