Digital output crosstalk PCI-6115

Similar Questions

• Only $line0 of digital output NI PCI-6014 accessible, other lines do not react in Labview

  Hello

  I have a NI PCI-6014 card with a card BNC 2120 DAQ and Labview 8.6. I'm trying to transmit digital signals, but only the digital IO port $line0 responds to my orders, while lines 1 to 7 don't work at all in Labview. With the measurement and Automation Explorer, I can access all the lines and change their State. I also tested another card (NI PCI-6154) with another card (CB-37F-LP) and had the same problem there (only $line0 of the digital port0 reacted, others don't). I have attached the VI very simple, I used to test digital ports. If the problem is known and what can I do about it?

  Thank you!

  Good never mind digital ports do not not Boolean signals, except $line0, which strangely accepts integers...

• PCI-6115 counter 0, 1 output current capability?

  Can charges of 50 ohm PCI-6115 player with the counter 0 or 1 meter outputs? The specification data sheet had no information on that.

  Hi src42,

  The data sheet indicates the maximum amount of current that can come from the digital lines to 13 my @ 4.35V.  This unfortunately not sufficient to drive a 50 ohm load.

  Best regards

• PCIe-7842R (series R FPGA) digital output does not work properly

  Greetings,

  I'm having some problem show TTL the correct voltage with my PCIe-7842R FPGA board.

  The block diagram of my code FPGA LV Moose appears in "analog - digital .png '. The idea was to convert an analog input (decimal value) to a binary code and 16-bit output by 16 DIO ports. I use the connection block SCB-68 has as the terminal and trendy on the FPGA 1 connector RDIO with SHC68-68-RDIO shielded cable.

  The compiled code ok. But during the test, I noticed that some ports has no output TTL levels correctly. For example, for input 1000 decimal, I would expect binary code 0000001111101000. However, some ports (DIO #6, #7, #9, etc.), which are supposed to ~3.3V (1 digital) high TTL output, output actually 0.8V. I have attached the result measured in 'exit digital test.png '.

  To ensure that the question was not because of the code of the LV, I did some more tests on DIO #6 with a simple example (simple digital output.png). The output was ~ 1V this time at the digital 1.

  It's really confusing because of the digital Edition is supposed to be simple. I used the same FPGA card for controlling roller shutters with TTL signals before and it worked fine.

  Does anyone have similar problems? Any suggestions are greatly appreciated.

  iron_curtain wrote:

  DIOs are connected to a controller digital galvo Cambridge Tech. But I measured the voltage at the terminals of the connector block.

  If you unplug the controller galvo DIOs, do they look good (have the right voltages).  Do you know how many of these entries to the need for controller?  I think you hit the limit the total current available for EID within the Council.

• How to configure the digital output of the pci terjeta 6023E in LabVIEW 8.5?

  Hi, I have a card PCI-6023E and LabVIEW 8.5 and I need is to configure the digital output on the card, but did not.
  My idea is to get a port of digital data on the map and control by a pwm small dc motor.
  I wonder what are the modules with which you can do.

  Hi skudero,

  Probably the web page tracking and the attached example will work.

  PWM in software timing using a digital output line

  Concerning

  Charley - NIB - SR 1368189

• 6534 PCI for digital output finished generates a continuous output

  Hello

  I use 6534 PCI for my application, where I generate a digital output, a model finished variable length in a continuous loop.  the code runs without error, but I'm not able to justify the behavior of the map. I intend to use the code inside the while loop as a Subvi and if I change the 'command' at the entrance table during each call to the Subvi, the output should vary according to the directives of the entry of the 1 d array.

  But this is not the case, the loop displays the previous value that has been given to Scripture DAQmx. If the control panel is changed the output instantly does not change. It takes a while before the actual output changes. The length of the array command I give is also 88 & 133. When I realize that the output is wrong, I disable the DAQmx write vi by a structure of the case, I would expect an error that the output buffer is empty, but rather the old value is generated whenever the start Daqmx vi task is exectuted without.

  My tax any problem is that the output buffer is not get replaced with the new value, but I'm specifyng the size of buffer, performing a registration every time and start the task, waiting until the task is done and the task stop. Each stop & writing should delete and empty the buffer, but I did not understad what goes wrong.

  Also, I thought that maybe that orders are put in queue up in the output buffer, acual generation is not as fast as the call of the DAQmx write & start, but if that's the case then even if I stop the vi the generation should be until the buffer is empty, but that doent happen VI, break breaks of generation. the number of iterations is equal to the generated models. If anyone can help as to what could be the problem?  find code attached below.

  Hello

  If I understand the problem you are experiencing, then the reason for the typical behavior when you run the VI, it is that you are not clearing the DAQmx task whenever you intend to go for a fresh DIO write. You stop just the DAQmx task that seems however to clear the buffer on board space.

  With this post, I am enclosing a VI of the sample that should work according to your expected behavior. You can even call this VI as a Subvi and can use it to update the DIO port with a digital model of variable length fees. Another fact that I would like to point out, is that, once you have initalised one table, it is not possible to reduce the length of the array. You can only increase by adding new elements. According to your needs given that the digital model that needs to be updated will be of variable length, each time you cll the Subvi, you must create a freash of appropriate length and feed it as input to the Sub - VI. Inside the Subvi, according to the length of this array of entry appropriate buffer space is allocated.

  Do trust this solution help solve you the problem, otherwise do not hesitate to go back.

  Best regards,

  Sagar G yapi | Application engineer | National Instruments - India

• Manchester in transmission/reception of signals using the digital output of the PCI-6224

  How a manchester signal can be sent and received using the OID of the pci card 6224?

  I want to create a signal NRZ manchester on a digital output channel and then have the possibility to receive and interpret the same type of signal on a digital input channel.

  Any help would be greatly appreciated.

  Hi VJohnson,

  You might find this post of discussion forum useful.

  Looks like LabVIEW has not Manchester coding/decoding built, but do able in your VI by replacing all the elements with the corresponding elements of two and using double the speed of transmission as your clock frequency.

  Thank you

  Scott M.

• clock calendar - digital output

  Hi all!

  I need timing equipment impliment on a few digital output lines.  That's what I have so far:

  

  

  I didn't get an oscilloscope for her yet, but I'm fairly certain that it works.  Please note that in this example, I use a PCI-6115.  I have 2 questions:

  (1) make what I do look reasonable at a quick glance?

  (2) I'm kinda mistified by the entry of clock source to the example of the clock function.  The analysis that I read just still confuses me.  I understand that the clock is what dictates the sequence of material.  I do not understand how to choose the appropriate clock source correctly.  More specifically, in the above example, I've only had the program work when I chose "20MHzTimebase".  What is c? Why this work?

  When I try to select ' Dev1 / / SampleClock ", I get the following error:"attempted to perform a route when the source and destination are the same point."

  When I try to select "Dev1/PFI0" or "RTSI0/DEV1", I get a timeout error in the wait_until_done.vi--> it does not appear that the waveforms are executed.

  That means the PFI and RTSI acronym for, and why they appear as options when you select a source of the clock?  Furthermore, why have they not worked as a clock source?

  I would be very grateful to anyone who could clear things for me a little.  Thank you!

  Have you read the http://digital.ni.com/manuals.nsf/websearch/01C075FB9478F94A8625786A007435BA? manual The definition of PF and RTSI are here. They are designed using external clock signals. You have the choice of using the internal clocks of analog output (20 MHz) or external clocks. If you do not connect the RTSI bus or PF what, whether you have no clock so no data will be output. Selection of as source does not work because it is not a source. You provide a source for it.

• Synchronization of analog and digital output with the external sample clock

  Hello

  First of all sorry for my English, I will try to explain what I want to do.

  I want my PCIe-6321 to send two custom signals (modification sawtooths) on a mirror controller. I would also like to generate output with my card at the beginning of each tooth of saw. Everything must be synchronized with an external k-clock signal of 100 kHz. The idea is that whenever the PCI receives a trigger to external clock, it sends two analog output voltages and when he received 1024 clock ticks it will also send a pic of triggering TTL. What I do is first prepare the map and after that in a loop sending and modifing the output values of the two signals and at the same time send a digital signal Boolean in each arch, so when's done it 1024 iterations of the loop I send an event to the digital port. Attached you can see.

  The problem is that I don't know how to synchronize both. Can I use the sample clock just to the analog output? I can use sample for the two outputs clock, or do I need to use the output of the meter? If don't know how to use it here.

  If I do nothing else bad/wrong, I would be grateful for feedback.

  Thanks in advance,
  Pablo

  I don't know how but I find the solution. I'm generating more than a positive value (as I was triggered maybe very fast the oscilloscope has been absent there). If I put the sample clock of digital output to use the sampling/ao/Dev1 clock that it doesn't, but if I put to use the same source as the OD (terminal where my external clock is connected), but the trigger to start the DO to be Dev1/ao/StartTrigger this works. I don't really know why, but it does.

  Thank you for your patience and your help. I put here the final code.

• redeclenchables strange behavior digital output

  I created a redeclenchables digital dashboard task (finished) digital output as follows: (in DAQmx C)

  DAQmxCreateTask("",&_taskHandle);
  DAQmxCreateDOChan(_taskHandle,"/Dev2/port0/line6","",DAQmx_Val_ChanPerLine);
  DAQmxCfgSampClkTiming (_taskHandle, "" / Dev2/Ctr0InternalOutput ", _clockRate, DAQmx_Val_Rising, DAQmx_Val_FiniteSamps, static_cast (_sampleCount)");
  DAQmxCfgOutputBuffer (_taskHandle, static_cast (_sampleCount));
  DAQmxCfgDigEdgeStartTrig (_taskHandle, "/ Dev2/PFI4", DAQmx_Val_Rising ");
  DAQmxSetStartTrigRetriggerable (_taskHandle, true);
  DAQmxWriteDigitalLines (_taskHandle, static_cast(_sampleCount), FALSE,-1, DAQmx_Val_GroupByChannel, _pDigital, NULL, NULL);
  DAQmxStartTask (_taskHandle);

  sample clock:

  DAQmxCreateTask ("", & _taskHandleCO);
  DAQmxCreateCOPulseChanFreq (_taskHandleCO, "/ Dev2/ctr0","", DAQmx_Val_Hz, DAQmx_Val_Low, 0,0, _clockRate, 0.5 "");
  DAQmxCfgImplicitTiming (_taskHandleCO, DAQmx_Val_ContSamps, _numSamples);
  DAQmxStartTask (_taskHandleCO);

  When I run the task without redeclenchables parameter, it output a correct signal. However, if I run with redeclenchables it out almost exactly 2 times faster than normal. For example, a pulse whose width of 10 ms became 5 ms and repeats again to be 2 pulses of 5 ms. This is repeatable, no matter how much or how fast triggers provided.

  My card is PCIe-6363. I do not know what causes this strange behavior, and I hope someone can help on this.

  Thank you.

  It disappears after reset configuration. Might be interesting for future reviews.

• Triggers the analogue output with PCI-4461

  Hello

  I'm trying to generate a signal of analog output triggered with a card PCI-4461. First I tried to use the feature OR DAQmx 'start analog edge' with the way analog input AI0 as the source and the channel analog output AO0 as task. After it gave an error that I tried to use the NI DAQmx 'start digital dashboard' function with PCI0 as source and channel of analog output AO0 as task. It ran, but did not produce any output. Now I wonder if I can use the trigger analog or digital of the PCI-4461 to all of the output.

  Thanks for support you,

  Pribislav

  Pribislav salvation,

  you still have this problem? I did exactly the same configuration (power play) and it works fine on my system. The PCI-4461 does not support analog triggering, that's why this error occurs.

  Kind regards

  Michaud

• analog sync of input with the onset of the digital output

  I'm trying out an analog signal to a file with a specified frequency samples.  I also need a digital output to trigger a measurement at a frequency specified on a separate system.  The frequency is controlled by the loop exits and timed when the iteration number divided by the period is exactly a whole number.

  Both outputs work.  The problem is that they are not synchronized.  The analog output amounts to about 0.5 ms faster than the digital signal.  (I checked with an oscilloscope)  They both start in the 1 ms each loop runs for, but I really need them to start at the same instant.  What can I do to synchronize?  Also, if I'm going in the wrong direction complete, please indicate.

  I use a card PCI-6723, which I think someone at some point, said not having a material sample clock.  That's why I try to use a timed software loop.

  Hi NEA.

  You must use the 6723's built-in calendar to accomplish what you want.  As the digital output subsystem is only clocked by the software, an appropriate solution should be to use one of the counters to the pulse output.

  The attached code should show how.  You can use the counter to output a pulse all samples of the AO N task.  Material requires the initial delay to have a minimum of 2 ticks, so the meter will be behind the task of the AO by 2 samples in this case.  There are different ways to work around this problem if you need (for example write two samples of 0 first).

  Best regards

• How can I more easily generate a pulse of digital output of finite length?

  Hello

  I need to open and close the two pneumatic valves using a TTL output (without load current or the output power) using a PCI-6280 or PCI-6601. The valves must open almost simultaneously and closing after different amounts of time elapsed (millisecond level timing, maybe 100 microseconds-level timing at worst). My current plan is as follows:

  -Create a task with two digital outputs (type of waveform) and another task with a counter that generates a frequency set by the user (I know I can use the generator frequencies on one of these cards, but I would have preferred a counter - the best selection of frequencies).

  -Wire the output of the counter at the entrance to clock two digital outputs.

  -Output of the meter is digitally triggered by another digital channel which I use to control if the pulse goes out. Through its counter node, it is programmed to be redeclenchables.

  -Two digital waveforms are drafted who have both consist of unique active high pulse (i.e. signals go ' down (for the amount of time user-defined) - low ".")

  -These signals is written to their respective ports and their tasks have started, as is the task of the meter.

  -Whenever the user wants to open taps, digital triggering is sent up and then back to low (this can be done with synchronization software, because it is not exactly when the fire valves). Whenever the user wants the valves open for a different period, different digital waveforms are generated and written in the buffers of the digital output channels.

  My problem is that it looks like a lot of effort for me to go and I wonder if there is a much simpler solution, that I don't know everything. You can program a computer to produce a pulse of finite length? Is there a faster way to program a digital output for that channel?

  Thanks to anyone who responds to their help.

  It is certainly instructive. Thank you.

  The thing is, I have only six total counters to work with and I have a lot of time to do things. To use these solutions, I would need to use 4 or 6 account counters required to my needs.also that I would need to synchronize their departures.

  Overall, I stick to my method for now - less system resources and synchronization can be don by using the same meter of finished output clock and not to use a trigger to all.

  Once again, thank you for your help so far.

• Moment of the digital output

  I use a PCI-MIO-16-1, and I'm trying to create pulses on each of the three digital outputs, using a hardware trigger.  I got a solution that sort of market by using a loop timed; the loop runs once per trigger, and inside the loop, I use avoiding to turn each of the three outputs at the right time.

  However, the problem is that the 1ms resolution of the timing of software is not good enough.  So I try to find a way to do it using equipment, so I can get a finer resolution.

  What I tried to do recently is to create a redeclenchables on one of the counters pulse train (using the example generate digital Pulse Train-finishes-redeclenchables) and use it as a trigger for the timed loop.  I can get the pulse train to give me three ticks for every time that I get a hardware trigger and then put a state machine inside the loop to turn each of the outputs.  (I am currently divide the material into three equal segments trigger.)

  However, although I can generate the pulse train very well on one of the counters, I can't manage to get the timed loop to use this counter as its source of the moment.  How can I do?  Or does anyone have a better idea how to do that?

  Unfortunately, the card you have does not allow for hardware timekeeping DIO. M series and recent X series Multifunction DAQ devices allow such a task. If you want, I can have a technical representative contact you to discuss your request and provide appropriate suggestions to optimize your application.

  Kind regards

  Glenn

  Technical sales engineer

  National Instruments

• How can I write a digital waveform to the digital output (traditional DAQ)

  Hello

  I use a NI 6023e, PCI, with 8 digital outputs. I generated a digital waveform. How can I write for a specific digital production line now?

  I only have Labview 7, so I can't use DAQmx.

  Thank you very much