Designjet 5000 PSU - Replace possible 1050C PSU?

Similar Questions

• Designjet 5000 + HP solutions Center

  Hello

  I have a HP designjet 5000 42 "printer that is installed on my network.

  I have the juice has a HP officejet 4500 and it is setup on the network.

  Of course the HP Solution Center came with the Officejet 4500.

  Is it possible to add the designjet to the solution Center. I tried "add a device" using the cd but it is not displayed.

  Any ideas?

  HP Solution Center does not support the Designjet printers.  What specific capacity are you looking for?

  For the Designjet you can have better results, post in the forum HP Designjet here.

• DesignJet 5000 'CHANGE printhead 2516' customer error said

  On a DJ, customer 5000 (sold the plotter to him a week ago) has used a printhead light cyan #83 for a week. Now says he gets 'CHANGE printheads 2516' error (it may indicate more precisely "replace 2516", but not sure "). Before use, the print head has been sitting 2 years however not sealed with masking tape on the nozzles and only had 17 ml shot from there. I installed and was surprised to see that it seemed to work very well and has about 1 1/2 weeks. I noticed that it weighed about 2-3 grams less than the other print heads (about 35.2 gm while others weigh about 37, 5-38 + gm or two, but it seemed to work fine.) I have purged the tubes until I installed print heads. All others are new.

  I am aware that the relocation and cleanup can possibly contact may be in order, but wonder if I am missing other opportunities that may be obvious to others.

  Thank you.

  Paul

  Hello

  If you clean the print head and still does not ink, you may have to replace it.

  Other cases, I have seen defective cartridges or tubes providing no ink in the print head causes this problem. I hope this isn't the case.

  Best regards

  Mike G

• HP Envy 17-j130us GPU replacement possible?

  Hello

  I've owned my HP Envy 17j130us for a few weeks now and it's every day a great disappointment.

  It takes years to start and does not give me half of the power that I expected an i7, even if it was supposed to be a great laptop.

  Once I'm not living in the States, it is absolutely impossible to find parts in Germany, but as I can not regret this purchase, I tried to "Push" somehow. First of all, I bought a 256 GB SSD and installed (had to import the cables!), now I really want to replace the GPU that is not also good for such a portable!

  Although it already costs a new and better PC, I wanted to know if there is the possibility of replacing the CPU (preferably NVIDIA) and how do I know which are the compatible GPU for my motherboard.

  I tried to look this information up from all over the web but I can't find anything specific on this model at all.

  Hello:

  The series you have is not a graphics card "card".

  He has a gpu chip, which is part of the motherboard and it cannot be upgraded or replaced.

  The only way to improve the graphics would be to replace the motherboard together with support, which may have better graphics.

  Needless to say that it would cost as much buying a new laptop with the graphic solution you are looking for.

• Is find and replace - possible to find a page without instruction?

  Is it possible to search all my pages in a site and find out all the uneducated (for example without the word 'cats') is it possible to find and replace the functionality? for example to apply a negative?

  Thank you

  It is indeed possible, providing some text is inside a tag any.  It could be in a list, title, paragraph, div, etc...  Use of the Research: specific tag option.  See screenshot (excuse the sloppy image).

  

  Nancy O.

• Need driver of HP/GL2 64-bit for DesignJet 5000 that would work with Win 10

  someone got a? or know where to get one? Driver HP site does not appear to have some files for pantone tables and presets and ICC profiles.

  Need driver which allows the selection 'process computer' in the tab 'Advanced' in the driver software.

  We get the error "lost data". I guess it is because the printer has 192 MB of SDRAM memory. Seems that it is related to the lack of printer RAM but I'm not 100% certain.

  Thanks for nothing.

  (Seems we have decommissioned all # messages and our experience, and some of our messages don't even appear under our user names - what the devil who is all about?)

  I have a driver for XP 64-bit, which might work.  Send me an email: DHook65857 at Aol.com

• HP 255 G1: Possible motherboard replacement

  Hi I currently have a G1 with an E2 AMD 255 HP - 1800 APU and I know that this cannot be upgraded without replacing the motherboard, so I was hoping I could get replacements possible motherboard I want to spend at least an i5 or AMD equivalent.

  Thank you

  Here is the Manual:

  Repair manuals

  If you try to go Intel, you can buy a motherboard and processor and heatsink/fan.

  If you go AMD all what you need is the motherboard, since your cooling fan/radiator can be brought to the course, and the CPU is soldered to the card.

  It's the motherboard you want:

  Card system (including thermal replacement materials): for use only with the models with a processor AMD A6-5200 ● models with 8 Standard 730670-501 ● Windows with Windows 8 Professional 730670-601

  I will assume that you have standard Windows.

  HP doesn't have the A6 AMD Board in the store... they have the jury of the A4 and it is stupid cheap:

  https://parts.HP.com/hpparts/Search_Results.aspx?mscssid=AE6D55D28A8C42CE89A8C049F3D07655&SearchIn=PartNumber&SearchPN=730671-501

  Because you don't have to share, it's going to cost close to $500. I can find you a good Intel 250 G1 opportunity for that price.

  You can find the jury for $67 eBay:

  http://www.eBay.com/ITM/HP-255-G1-laptop-motherboard-AMD-A-series-A4-5000-1-50-GHz-730671-501-tested-/291792328450?hash=item43f02d9702:g:298AAOSwM4xXYC9Q

  I know you wanted something a little more powerful, but the A4 will be a major improvement on what you have.

  The laptopaid vendor, is one of the best on eBay for this sort of thing. I can't count how many things I've bought from them.

  Post back if you need help most. The manual just shows how to replace the motherboard. On the port your fan, memory, the wireless card. You need to reinstall the original Windows, but the motherboard has a key built into the BIOS Code and will only activate. If your hard drive still has the original installation of HP it should activate itself when first connected to the internet, but be ready if necessary to do a system restore.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• DesignJet T2530: T2530 selection automatic Roll Correct

  We recently bought a DesignJet T2530 to replace our old Gestetner requiring parts that are no longer available. We've had for about a month now and we had questions make him print the good roll all the time. We have a wide roll 36 '' loaded roll of 1 and a 30 "wide roll to roll 2. When printing the drawings AutoCAD or a PDF Adobe, 24 "x 36" designs would be to print in portrait mode (24"wide) to 30' wide roll instead of landscape (36" wide) to 36"wide roll." Also, 30 "x 42" designs would be automatic selection of portrait print (30' wide) for the 36"wide roll instead of 30" roll. " We called our service contract provider and they came out, looked through a bunch of settings and finish the download complete driver with PS drivers and HPGL2, set a custom. PC3 for AutoCAD file to force the printer to print 24 "x 36" designs on the 36' roll after we say from the printer, and everything has worked for a few days. " Service came out again, changed a few extra settings in the printer properties, ended up needing to replace the touch screen because it was just bad out of the box, and again once it worked fine for a few days. More recently this week, it started printing the 30 designs "x 42" 42"wide on the 36" "roll, cut 3" on each side of the drawing. " Service came out yesterday again, was here for about an hour, has insisted that it is absolutely not the machine and it must be a problem with AutoCAD and Adobe (which seems strange since it has the same problems of each program), tried a reset of the printer without result and basically said it's just not to the automatic selection the right to ride , so we will have to change the settings in the properties of each time that we print something. Then, after the left, custom. PC3 file, put it in place before (as previously mentioned) has stopped working properly and the 24 "x 36" drawings started printing out on the 30' wide roll again. " As it is now, when I print a drawing, I have to go into the properties of the printer in the print window, select the correct size paper, select the correct role and select the correct orientation so that it can print correctly. I put just customized. The PC3 in AutoCAD files for it so I do not always go through this when printing from AutoCAD, but I must still manually change all these settings for each picture I print from Adobe and I don't know if these custom. PC3 settings will decide to stop working again like last time.

  Someone else has had this problem on this model printer and, if so, have you found a solution so he can get the correct width for automatic selection?

  Hello

  Go to the printer Embedded Web Server and select the option use the exact width of the roll.

  Also, make sure that the drawing was generated landscape as the application will replace all the settings on the driver and the printer.

• DesignJet 2500cp main engine belt

  Any solution to replace the small belt, since HP offers no support more and makes this unusable printer

  I have a designjet 2500cp and replaced the belt.  It took me about five hours to complete the task.  I got the manual 2500cp online (I can't remember where) and ordered the belt directly from HP.  For now, I'll have is part of the ink system.  I bought a new ink system and the printer works ok for a while then I get an error on the printer to mixed inks... ready to my wrists slit on this "thing" after having spent $600.00 on a new ink system.  If you don't have scrapped it, I could scan pages and email them to you.

• upgrade xp driver for win 7

  We have a DJ5000ps plotter with an xp driver. Just bought a new computer with Windows 7. This Tracker is no longer supported. Is it possible to have a driver for win 7? Can I combine the .inf for xp file in Windows 7? Anyone interested in writing a pilot for us? We can just not a new tracker at the moment. Thanks for your help.

  Hi landarch,.

  As Bob_Headrick says in his post below.

  This forum focuses on the level of consumer products.  For the Designjet you can have better results in the forum HP Designjet here.

  http://h30434.www3.HP.com/T5/printer-all-in-one-software/is-there-Windows7-driver-for-HP-Designjet-5000PS/TD-p/1249737

  However, I found an "accepted Solution" where some customers have had success using the mode of Windows XP to Windows 7 PCs.

  http://h30499.www3.HP.com/T5/Windows-7/Designjet-5000-PS-need-Windows-7-64bit-driver/TD-p/1129850

• MacBook Pro 2014 - failure of the graphics card for the 2nd time in 2 years - no guarantee

  Hi all

  end of 2014, I bought a new 13 inch Retina Display MacBook Pro mid 2014 model (A1502, EMC2875). A few months later, the graphics card has failed - no obvious reason. Apple replaced. Now, the graphics card has not yet. Still, the mac worked perfectly well (no overheating of the noise, nothing) and all of a sudden - no understandable reason or external actions, the graphics card has failed. Unfortunately, I do not have a guarantee of more. At least, I can access my documents by connecting two Macs, so I hope that the material is not affected.

  My model (1502) apparently only has a single integrated graphics processor.

  My questions:

  • After some research, I discovered that Apple used to have these problems with the 2011 edition. They have implemented a replacement program. Does anyone know sth on this subject?
  • What graphics card would you recommend? How much such a graphics card? Where could I buy a cheap?

  Of course, I don't want to reuse the same type - guess I don't have to explain how @* #&! I'm after two times the same problem within two years after the purchase of a brand new MacBook Pro...

  I would appreciate any recommendations and links!

  Best regards

  Rahel

  -As you say, your Mac model uses the graphics processor integrated in the CPU chip. So, there are ios no replacement possible. The CPU is soldered to the logic board

  -The problem with the 2011 MacBook Pro was with the discreet Nvidia, not the graphics unit integrated in the CPU graphics unit.

  -When you went to an Apple store just says the genius of APple?

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop.

• Help! Does this affect my Wi - Fi connection speed? Install a Virtual Machine.

  I went recently through a malware attack on my PC of 10 windows trying to reset my Twitter, but there is no way in, unless I want to find my password, I went through an application and he broke my PC, it started failing and it is very slow. Then, I used 450 GB of storage and 4 GB of RAM on my iMac to install Windows 10 and listed all the apps in paper and install them, I'm almost done with the process. I use also 2 hearts, but it will affect it on Wi - Fi speed since I was having problems with YouTube and Google Maps and charge very long, but sometimes quick Web pages. YouTube sometimes show 144 p instead of 720 p. Here are the specs on my Mac, and I bought Sept. 26., 2015, without replace my Mac Pro ($5000), but replace the even older Mac (2011) on my studio.

  Data sheet: iMac 21.5 ", end of 2013

  2.9 GHz Intel Core i5

  8 GB 1600 MHz DDR3

  NVIDIA GeForce GT 750M 1024Mo

  Mac OS X 10.11

  Mouse and the magic keyboard

  The reason why I need Windows is to connect my Galaxy 5 Note to transfer videos to actually charge my iPhone reviews/tutorials on YouTube. And windows gets slower and slower, it is bought in December 2012, it runs Windows 10.

  PC HP Pavilion P6-2330

  Next generation AMD A6 - 5400K acceleration processor

  6 GB DDR3 RAM

  1 TB harddrive

  CD player

  A WiFi 802.11 b/g/n

  Mouse and keyboard comes with the computer

  ViewSonic VA2455Sm monitor

  Logitech R10

  Windows Pro 10

  Installed 10 Windows on my Mac slow down my Wi - Fi? What should I do to my Windows PC? My Chrome is wiped, and this affects performance when installing Windows 10 on my iMac?

  iOSAndroidRebel wrote:

  Installed 10 Windows on my Mac slow down my Wi - Fi?

  No, it shouldn't.

• Drive DVD SD-R5112-NEB has stopped working - need a compatible

  Hello.

  My Player DVD SD-R5112-NEB has stopped working. Please notify compatible replacement, possibly upgrading to faster drive.
  Thank you. Scottowner

  Upgrade procedure is not the same for each laptop model and it is very important to know what model of laptop you have. You can also view s manuals for your laptop and I hope that you will be able to find a list of compatible optical disk drives.

  Bye and good luck!

• OpenComConfig sets the bad baud rate

  -WinXP

  -CVI 9.0.1 VERSION

  -7904 compact PCI sea level

  -COM1 on motherboard

  When I open a port at 115200 baud, it opens in reality at 9600 baud.

  My software uses OpenComConfig (115200) but the serial port will eventually be open to all that

  "setting of the operating system" is for the port in the control panel.

  This does not occur when you use HyperTerminal

  As soon as the INVALID PARAMETER (line 10 below) is detected, the port is REOPENED to the configuration of the system instead of my bad = OpenComConfig (port, ' ", 115200, 2, 8, 1, 50000, - 1);
  No error is returned by this function.

  Activity captured for the serial port for OpenComConfig() port monitor is:

  0.00021036 0 84615u.exe IRP_MJ_CREATE Seacom2k10 SUCCESS Options: open
  1 0.00000391 84615u.exe IOCTL_SERIAL_GET_BAUD_RATE Seacom2k10 SUCCESS
  2 0.00000279 84615u.exe IOCTL_SERIAL_GET_LINE_CONTROL Seacom2k10 SUCCESS
  3 0.00000279 84615u.exe IOCTL_SERIAL_GET_CHARS Seacom2k10 SUCCESS
  4 0.00000251 84615u.exe IOCTL_SERIAL_GET_HANDFLOW Seacom2k10 SUCCESS
  5 0.00001117 84615u.exe IOCTL_SERIAL_SET_BAUD_RATE Seacom2k10 SUCCESS rate: 115200
  6 0.00000670 84615u.exe IOCTL_SERIAL_SET_RTS Seacom2k10 SUCCESS
  7 0.00000643 84615u.exe IOCTL_SERIAL_SET_DTR Seacom2k10 SUCCESS
  8 0.00000475 84615u.exe IOCTL_SERIAL_SET_LINE_CONTROL Seacom2k10 SUCCESS StopBits: 1 parity: EVEN WordLength: 8
  9 0.00000307 84615u.exe IOCTL_SERIAL_SET_CHAR Seacom2k10 EOF:0 SUCCESS ERR: ff BRK: ff EVT:0 XON:11 XOFF:13
  INVALID PARAMETER to 10 0.00000251 84615u.exe IOCTL_SERIAL_SET_HANDFLOW Seacom2k10 XoffLimit:5000 of XonLimit:5000 to replace: 40 Shake: 1
  11 0.00000251 84615u.exe IOCTL_SERIAL_GET_BAUD_RATE Seacom2k10 SUCCESS
  12 0.00000223 84615u.exe IOCTL_SERIAL_GET_LINE_CONTROL Seacom2k10 SUCCESS
  13 0.00000251 84615u.exe IOCTL_SERIAL_GET_CHARS Seacom2k10 SUCCESS
  14 0.00000251 84615u.exe IOCTL_SERIAL_GET_HANDFLOW Seacom2k10 SUCCESS
  15 0.00001062 84615u.exe IOCTL_SERIAL_SET_BAUD_RATE Seacom2k10 SUCCESS rate: 115200
  16 0.00000670 84615u.exe IOCTL_SERIAL_CLR_RTS Seacom2k10 SUCCESS
  17 0.00000643 84615u.exe IOCTL_SERIAL_SET_DTR Seacom2k10 SUCCESS
  18 0.00000419 84615u.exe IOCTL_SERIAL_SET_LINE_CONTROL Seacom2k10 SUCCESS StopBits: 1 parity: ODD WordLength: 8
  19 0.00000307 84615u.exe IOCTL_SERIAL_SET_CHAR Seacom2k10 EOF:0 SUCCESS ERR: 0 BRK:0 EVT:0 XON:11 XOFF:13
  20 0.00000475 84615u.exe IOCTL_SERIAL_SET_HANDFLOW Seacom2k10 Shake SUCCESS: 1. replace: 0 XonLimit:2048 XoffLimit:512
  21 0.00000251 84615u.exe IOCTL_SERIAL_GET_BAUD_RATE Seacom2k10 SUCCESS
  22 0.00000223 84615u.exe IOCTL_SERIAL_GET_LINE_CONTROL Seacom2k10 SUCCESS
  23 0.00000223 84615u.exe IOCTL_SERIAL_GET_CHARS Seacom2k10 SUCCESS
  24 0.00000251 84615u.exe IOCTL_SERIAL_GET_HANDFLOW Seacom2k10 SUCCESS
  25 0.00001006 84615u.exe IOCTL_SERIAL_SET_QUEUE_SIZE Seacom2k10 SUCCESS Insizing: 50000 out: 0
  26 0.00000279 84615u.exe IOCTL_SERIAL_SET_TIMEOUTS Seacom2k10 RI SUCCESS: RM:0 - 1 RC:0 WM:0 WC:0

  Sorry, I think that the limit error XON/XOFF wrong main to assume that you were actually using handshaking, but never, you indicated that you were. This problem that you mention actually open any port, regardless of whether you use XON/XOFF handshaking. The limit of 4096 seems to be imposed by the driver, so it is not something that can be changed in the CVI code layer. However, we can impose a maximum of 4096 for XON/XOFF limits, that we spend in the Windows SDK, so that the error can be avoided when you are booking a superior to 40960 input buffer.

  We will do both the fixes mentioned in this thread in the next version.

  A. Mert

  National Instruments

• EliteBook 8470p: update video card

  Hi, I need know if it is possible to upgrade the video card on my laptop, I need more powerful system of grafic vedoe is.

  I7 3720qm processor

  memory-8 GB

  amd radeon 7500 video card m.

  Hello

  You can read the following message:

  http://h30434.www3.HP.com/T5/hardware-upgrades-replacements/possible-dedicated-GPU-upgrade/m-p/5351981

  Kind regards.