DesignJet T1200
Hello
My HP DJ T1200 displays white screen with LED lights I format and therefore does not work, there is t he not choice to replace the trainer?
Thank you for your help.
Hello
With the wide printer, take out the trainer, remove the battery for 5 min and reinstall. It works sometimes.
If possible, share the status of the 3 leds on the trainer.
The issue could be the trainer or the APC's hand. The Leds on the trainer can tell you what part is faling
Best regards
Mike G
Tags: HP Printers
Similar Questions
-
Designjet t1200 MFP: length Maximum of t1200 printer paper?
"We're trying to print a poster of long (150 '') on our T1200 but when we enter the length and width (150 ' x 36') he continues to change the 150 to 129 ', which is in the box greyed out under the length of the custom paper box.
The maximum length we can print on a T1200 is 129' or is there a way around this? I read the manual, but it does not say what the maximum length of paper that you can configure in the menu custom. At least, I didn't see it anywhere.
Also, I downloaded the driver to my computer earlier, just to see if the latest driver could have corrected it, and it's the same thing: gray area below the custom length box that says: "5.51 - 129.00.
Hard to believe that HP would put an arbitrary restriction on the length of the paper you can print on. There must be a work around.
Thanks Mike. Tried a couple of things and finally decided to use the 5500PS driver. Works like a charm. Maximum length is now 150 feet!
Mike, could you print past the 129 "max limit the driver t1300?
Only downside, is that it there is no roll selection on the 5500, since it is a single roller machine the the t1200 is double rolls. It comes default roll 1. But for the banner occasionally use of impression, it will work very well. The rest of the time, we can use the original driver T1200 and not lose the roll option.
So now I use the driver of 5500 on a 1055 C and a T1200, as a 5500PS. A versatile driver I would say!
-
HP Designjet T1200 PostScript: during the t1200 firmware update file
I tried several times from several systems to download the update of the firmware:
TT6 - TTAJ_08_02_03.3_mvl40 - x 86 - opt_B.fmw
Downloads of files consistantly with a 467 720 KB file size.
"The process of updating the firmware has not been successful. The file you have selected may not be good, or the problem may be due to a transmission error. »
1. How can you contact HP for updating the firmware file.
2. other solutions?
Hello
Did you try to contact HP and get another FW file?
Best regards
Mike G
-
Designjet T1200 HD-MFP: Designjet T1200 Scanner
Hi all
Im having a problem with the scanner pc not find and connect to the scanner. Have checked connections, turned off both scanner and pc, son of the late disconnected, powered by scanner and pc upward and reconnected the son of fire. Used the two ports of wire before the scanner. Re-scanned dozens of times, and the pc scanner won't scan. Even went as far as using the system recovery disk, still no dice.
I see that the manual recommends to replace the interface board and the interface cable. Although I have found no part number for the interface cable, at least than the average fire wire cable. Any input would be greatly appreciated.
Thank you!!
Hello
Yes, you will look at a problem with the cable or a firewire interface card. In some cases, the problem could be the APC of the PPC hand.
-
DeskJet t1200: jury of trainer T1200
Hello
I have a damaged on a deskjet t1200 printer formatter Board needs to be replaced.
- The formatter Board come with HARD drive or are sold separately?
- If I get the formatter Board, I can buy one out of the HARD drive tray and load the firmware on it? in the affirmative, please send me the markets / youtube video on how to do this.
- A link to buy complete formatter Board + drive HARD will be highly appreciated
Thank you.
Hello
Here are the part numbers
CH538-67004 trainer Board - do NOT include the hard drive (HDD) - for the Designjet T1200 Printer series
CH538-67078 SATA hard drive (HDD) - includes: firmware - for use with Designjet printers
Trainer and HDD have never were sold together, always separate.
Make sure you get these new pieces, otherwise you can change the identity of the printer and will not be able to recover from that
-
47.01 restart the printer if the problem persists
Hi all
Someone has an idea to help on this case, I was open plotter HP DesignJet T1200 and I got a message the screen says that error 47.01 restart the printer if the problem persists, call the HP Support and I can't do anything.
anyone can help it would be very useful to me and many thank in advandce.
An error was detected during the detection of the print head. Reinstall all the -
Designjet T120: HP T120 error BA7F11E0 designjet
We have a HP designjet T120 when power on/off, this (BA7F11E0) error message appears on the screen immediately. No movement of transport or initialization is performed. Just the error and nothing else. Pls help.
Thank you
Hello
Try to isolate the printer, remove the printhead, inks, connectivity cables and turn on the printer.
If the error persists, it may be a problem with the APC hand.
Best regards
Mike G
-
DesignJet 130nr: canvas print Designjet 130NR
Print on canvas of sheet (13 x 19) on Designjet 130NR works very well. Called HP Support asking if there are 24 "canvas rolls that work. Told me and it makes sense, the tool can not handle the Cup fabric.
Someone at - he found and printed successfully pre-cut large canvases for the 130NR? I've got a good big letter opener, but as anyone who uses the 130 know, it rejects easily paper cut perfectly.
Thank you
Marty
Hello
Strawberry is not really designed to cut the canvas. Is too thick
You can still use it, but you will need to replace it more often.
If your knife used to work, you may need to replace it now
Here is the part number Q1292-60064 Media knife
-
Designjet t125: designjet t125 blue screen error B332347C
Hello.
I was ask to get this error:
When you feed the plotter that blue screen appears with this code: B332347C
I can't find the service manual for this, if anyone can help me?
HELO try this solution
You need to replace hp designjet encrypted t520 chip on the motherboard inside the plotter
You can buy it on ebay http://www.ebay.co.uk/itm/HP-Designjet-T520-Blue-Screen-Error-Solution-Encrypted-chip/282223353841 -
Designjet t520: designjet t520 error b3d73738
HP Designjet T520 36 inches gives b3d73738 on the screen, never seen that before and isn't anythong on this subject,
the printer does not start or let me take any operation
need urgent hepl on this issue.
Thank you
Hello
Try the following
-Replace the power cable
-Connect the printer to a different outlet
-Isolate the printer, remove the ink cartridges, print head, cable connectivity
If you still have problems, you may need to replace the APC's hand
-
Designjet T520 36 inches (CQ893): Designjet T520 36 - in
My tracer: HP designjet T520 36 inches (CQ893) start.
The screen is blue, B87E7114 error code
Turn off and turn on probably. Power button 15 seconds and powering button 50 seconds also.
If push yellow power light. power on no beep error.
End of warranty: 2015.02
What is my error code?
Thank you
Sorry, but your post is very confusing. You've got an ok error code, after that I do not understand what you mean by switch / stop and seconds. First thing you need to do is to unplug the plotter of the power source. Wait about 30 seconds and plug back in and if the power does not turn on by itself, use the power button to turn it on and tell us what appears on the screen.
-
HP Designjet T1300 error 08:04
Hello!
I have a T1300 Designjet, a few years old (2010 I think) and I have printed a few rolls of paper on it. (5-6)? There are a few firmware updates he has begun to show 08:04 error message. He asked me to update the firmware, if the problem persists (does it well). I have the new firmware (?) IG_04_00_05.2.
Sometimes I have to reboot 10 to 15 times before I can print. Sometimes it goes to error if I don't use pace for an hour or two. Sometimes he goes to error in the middle of printing, or just by turning or when ever. Sometimes it starts immediately and I can print all day with no problems.
Any ideas?
Now, I checked again for the new firmware. the printer says there is new firmware, but he went to 08:04 error mode in the audit.
Now after 4 restarts, the printer started to install the new firmware. at the end of the installation program stops and when restarting, the printer starts at 08:04 mode.
Restart the printer again and again. Allways 08:04 code. What is 08:04 code means?
OK... updates history:
Today first MS_01_01_23.1 was installed and after this IG_04_00_05.2.
No newer firmware available.
I will update this if it doesn´t enter the error mode more...
Today, I finally had the time to print again. The T1300 always happening in error mode 08:04.
Help!
I've never seen an INVERTER causes a hardware failure, but I saw them will interrupt power. I unplug it and try it this way for a test. Can you connect a computer directly to the printer without going through your network and see if it starts and prints normally then?
-
DesignJet T2530: T2530 selection automatic Roll Correct
We recently bought a DesignJet T2530 to replace our old Gestetner requiring parts that are no longer available. We've had for about a month now and we had questions make him print the good roll all the time. We have a wide roll 36 '' loaded roll of 1 and a 30 "wide roll to roll 2. When printing the drawings AutoCAD or a PDF Adobe, 24 "x 36" designs would be to print in portrait mode (24"wide) to 30' wide roll instead of landscape (36" wide) to 36"wide roll." Also, 30 "x 42" designs would be automatic selection of portrait print (30' wide) for the 36"wide roll instead of 30" roll. " We called our service contract provider and they came out, looked through a bunch of settings and finish the download complete driver with PS drivers and HPGL2, set a custom. PC3 for AutoCAD file to force the printer to print 24 "x 36" designs on the 36' roll after we say from the printer, and everything has worked for a few days. " Service came out again, changed a few extra settings in the printer properties, ended up needing to replace the touch screen because it was just bad out of the box, and again once it worked fine for a few days. More recently this week, it started printing the 30 designs "x 42" 42"wide on the 36" "roll, cut 3" on each side of the drawing. " Service came out yesterday again, was here for about an hour, has insisted that it is absolutely not the machine and it must be a problem with AutoCAD and Adobe (which seems strange since it has the same problems of each program), tried a reset of the printer without result and basically said it's just not to the automatic selection the right to ride , so we will have to change the settings in the properties of each time that we print something. Then, after the left, custom. PC3 file, put it in place before (as previously mentioned) has stopped working properly and the 24 "x 36" drawings started printing out on the 30' wide roll again. " As it is now, when I print a drawing, I have to go into the properties of the printer in the print window, select the correct size paper, select the correct role and select the correct orientation so that it can print correctly. I put just customized. The PC3 in AutoCAD files for it so I do not always go through this when printing from AutoCAD, but I must still manually change all these settings for each picture I print from Adobe and I don't know if these custom. PC3 settings will decide to stop working again like last time.
Someone else has had this problem on this model printer and, if so, have you found a solution so he can get the correct width for automatic selection?
Hello
Go to the printer Embedded Web Server and select the option use the exact width of the roll.
Also, make sure that the drawing was generated landscape as the application will replace all the settings on the driver and the printer.
-
hp designjet t790 22.0.10 error code pls help...
This code is important when someone replaces the star engine and when reinstalling the electronic module that they mix the large 2 connectors on the main map.
-
DesignJet 200 C3180A: Lost printer driver-DesignJet 200
I seem to have lost the driver for my DesignJet 200 C3180A antique during the upgrade of Windows 10. It worked two months ago (on Windows 7), and the only change I made to the computer - I think - is the upgrade. Now when I go on the list of printers it just isn't there. I tried to search the Internet but nothing seems available after Vista. I'm at a loss as to how I had it works on Win 7 now! Any ideas where a Windows 10 driver is not found?
I connected via a parallel adapter / USB and the port was virtual USB001 (or was it 002?) and he has worked in the past connected like that.
Any help would be appreciated, thanks.
Hello
Try this other driver for the DJ 430
Hope to work
Maybe you are looking for
-
I just bought a windows Tablet and impossible to download firefox
I just bought a Nokia Lumia 2520 (Verizon) and can not get any version of Firefox to download. I'm just not finding the right version? I use Firefox on my desktop without any problem.
-
Is there a program for Windows such as Final Cut Pro for Mac?
Hey guys, I was just wondering if Windows had an editing software, like the Mac does with it's Final Cut Pro, which allows me actually add and move images on the film plays in the background (Ergo you can have photos and movies playing at the same ti
-
HP Pavilion N207TU: Upgrade of RAM in my N207TU
Currently it has 4 GB of RAM, and I would like to upgrade to 8 GB. Will it be possible? There is an empty slot where I could insert another 4 GB of RAM? Or I have to replace the existing one with 8 GB of RAM. Or is it not possible at all?
-
How can I save D drive on an external device (drive C is SSD) D is the partition
I have a new Dell XPS 8500 Windows 7 with a SSD 250 (C and OS holding) and a disk partitioned d for photos, documents, etc. I am able to backup C on an external device, but can I also do for D? If this isn't the case, I have to copy everything manu