Designjet T520: Designjet T520: failure of the printer

Had Designjet T520 about 18 months. Use it only for printing large format on roll paper. Error message: the printer failed. "There is a problem with the printer or ink system. Turn the printer off, then on. If the problem persists, contact HP. »

Have made the procedure "on - off" several times including disconnect, allowing the printer to sit idle and then plug it in, turn on and still the same problem. I also removed and checked each ink cartridge and cannot detect all problems.

Advertisement

Remove all the ink cartridges and turn on the plotter.  When he asks the ink, put them in one at a time and see if the error is displayed when only one of the ink cartridges installed.

Tags: HP Printers

Similar Questions

  • HP6830: Failure of the print queue

    HP replaced my 6830 due to failure of the print head. New printer works proud desktop using Vista. Previuosly I could print from my laptop wireless as well, but it's time the print queue says printing, fails to print and return to errot impression. I know that thw laptop is connected to the printer thr and I even can it ping ipconfig without problem. I have been through software support, and to the low load options hear everything without any result. I am now confused.

    Hi @3391816Sablenip,.

    I read your post and see that the replacement printer is wireless print on the Windows Vista-based computer, but not the laptop running Windows 7. I will definitely do my best to help you.

    If you have a valid IP address for the printer, then try and access the Web built-in to the printer server.
    Type the IPv4 address in the address bar of your web browser. (Internet Explorer) It to load the page.

    You mentioned that you can test the printer, just to check a real contact, check the network IPv4 address on the computer to see if the first 3 sets of numbers match the IPv4 of the printer address.

    Press the Windows and R key at the same time, to show the command line run, type cmd, then type Ipconfig.
    Check the IPv4 address.
    Now, check the IPv4 address for the printer.
    If this isn't the case, then the printer and the computer are not on the same network.

    Do the first 3 sets of numbers match?

    Check the address IPv4 of the computer to verify that it matches the IPv4 of the printer address.
    Printers and devices, right click on the printer, on the left, click printer properties, select the Ports tab, click on Configure Port.
    If they do not match and then close the window configure the Port and click on create a port and follow the instructions in the wizard.

    Type the IPv4 address.
    Make sure the printer is online.

    Test the printer. If creating the new port doesn't work, run the Add Printer Wizard.

    If you're still having problems, download and run the print and Scan Doctor, he will diagnose the problem and could solve it automatically.

    What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

    If the problem persists, try the following steps to see if it will be useful. HP printers - print jobs stuck in the print queue (Windows).

    If you appreciate my efforts, please click on the "Thumbs up" button below.

    If you have any questions, please let me know what steps you have taken and the results. Thank you.

  • "Failure of the printer: there is a problem with the printer or ink system" message

    I get printer error message on my printer Officejet 6700 Premium.  I'm on a Mac OSX 10.9.2.

    I have reset the printer and I tried to update the firmware by the instructions, but he tells me that the device is busy and won't.  The printer is out of warranty but was hardly used - less than 200 printed pages - UGH!

    What can I do else?

    Hi Embie2014,

    Thanks for letting me know you are using the HP cartridges No.

    HP recommends you to use genuine HP cartridges. HP does not guarantee the quality or reliability of cartridge not HP, or filled HP cartridges. If you use genuine HP, the following cartridges no could not solve your problem of print quality.

    A "cartridge problem," "ink cartridge failure," or "Incompatible cartridge" Error Message appears on the all-in-one.

    Printer cannot print black ink or color ink or prints blank Pages.

    This document explains how to clean the print head.

    Thank you.

  • Print PDF caused the failure of the print spooler

    I have been all over these blogs, and nobody has the answer. I had no problem and then today when I tried to print a pdf file, everything went haywire. I can not print, I can't remove and reinstall my printer, I can't restart the print spooler (it tries but stops, and then said: he started, but he didn't). HELP ME, PLEASE.
    Janie

    Hello jrino,

    Thank you for using the Microsoft answers Forum

    Apart from the pdf printing problem can you print other programs such as Word, Notepad, or Wordpad? Try to go to the event viewer and see what errors are being given in the viewer list. Also during activation of the print spooler service, make sure that the spooler depends on all the services are started as well.

    Access Event Viewer: right click on computer and select manage. Click event viewer, and then expand the view so that you can access the different categories. Expand Windows logs, and then click Application. Scroll down and see what kind of errors you found and see if that helps you evil pulls on the question. Post what you find in this thread.

    Looking for services that depend on: click console in the management of the computer Services. Click Services and Applications and then click Services. Find the print spooler and double-click to view the properties. Watch dependent services for the spoooler and to ensure that these services are started and running as well. If one or more of the dependent services do not work this may cause your spooler to stop working as well.

    Judd
    Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

  • Failure in the printer or ink systems

    What can I check after checking the unit ink and printhead on my printer IPSR 8600?  Get the error message 'problem with the printer or ink systems' have checdked ink cart. and print head.  All seem good.  Where should I go from here?

    Hello

    You have followed the steps in the link below.

    http://support.HP.com/us-en/document/c03096304

  • Failure in the print module?

    Hello

    I have LT 2.5 installed on my Windows Vista computer

    In the printmodule, I'm trying to save my file as a JPG file. This is no problem if it is just AN image

    If I want to save several photos, the images will be saved as ', jpg "instead of".jpg ".

    So to speak one ',' instead of a '. '.

    When I have to rename each picture

    What's wrong???

    Help, please

    Enrique

    Print to JPEG in the print module, I see as favoring boards contact or multiple images on a single sheet.

    Looks like you should be using the library module and choice of export. You can find a few models, and you can do it yourself very easily.

  • failure of the printer

    my printer hologram of stopped for some unknown reason, and I can ' t get "er's"

    Control cables.

    Check Ink/toner.

    See also: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-printer-problems

  • ERROR MESSAGE HP6700 - PROBLEM WITH THE PRINTER OR INK SYSTEM CONTACT HP

    I JUST BOUGHT A HP OFFICEJET 6700 (LESS THAN 1 WEEK), THE PROBLEM OF PRINTER OR INK SYSTEM MESSAGE, TURN PRINTER OFF THEN WE IF THE PROBLEM CONTINUES CONTACT HP. IS DISPLAYED ON THE PRINTER SCREEN. I DID EVERYTHING SUGGESTED, AND MORE MORE, BUT THIS CUSTOM MESSAGE CLEARLY.  ALL DIAGNOSES OF THE PRINTER THE PRINTER IS FINE.  THE OPERATING SYSTEM IS WINDOWS 7.

    Mahamoud,
    Your article made a walkthrough basic troubleshooting, ending with the question if the print head is repairable. Because it is not on the 6700, the article isn't really the problem.

    Here is the solution I found to this problem:
    I discovered that eliminating all ink cartridges allows the printer at startup (although there is a message saying the missing print cartridges).
    Putting the cartridges in a binary regression revealed that the ink has been bad. (In my case, I only got the message of failure/printer ink when the yellow cartridge was in the printer).
    Replacement of the restored cartridge the printer functionality.
    That's the good news.
    Now the bad news: for HP.
    The generic error message indicates a failure with the printer or the ink system. No differentiation. With the electronics in the cartridges (that the client pays a high price for), looks that HP could not understand how to indicate a cartridge problem. This error message is not only unnecessary, but misleading. The printer indicates only a power reset and then contact HP. There is no indication that he might be a cartridge problem, not to mention what cartridge has failed. By the way, my customer encountered this problem when you replace the color cartridges. The cartridge failed was a new replacement.
    All of the web enabled features, fax, scanning features, print included with this printer are not very useful if the user can't get the dang thing to print.
    Another problem with this printer, is that, even when you only print in b & W, the printer uses little color (ostensibly make Blacks more "BOLD"). Then, finally, a color cartridge will go low or empty, even if only B & W printing. And guess what, you can't continue to print n & B if one of the color cartridges are out of ink. Thus, HP... How is this useful printer in an office environment, where most print tends to be B & W?

    (I would add; the solution in the message of failure/printer ink cartridge cannot fix your problem if, in fact, there are a few default printer. But if the problem is in the ink system, then the troubleshooting cartridge can help you).
    I have posted similar comments on Amazon, for this printer, in the subject line: shame on you, HP.

  • HP Officejet 6600 e-all-in-one printer - H711a/H711g 'Ink system failure', will not print computer

    At first, it was just a problem with do not print from the computer.  Error messages had to do with the failure of the print head or do not find print head, etc..  After going through several different controls online, download the scans, etc., it does not at all, print showing an error message "ink system failure".  I tried to remove and reinsert the 4 printheads (black 932, 933 colors) and turning market and check the caps and unplug the power.  Since this is a wireless network, I can't unplug the USB.  It was the OK signal.  Now, with this error message, I don't see the home screen printer controls.  It just says: put it on and then contact HP.  Help, please.  Very frustrated (it didn't happen all at once - a first he wouldn't print from the computer sometimes, other times.)

    Wildrat58,

    If you get ink system failure and you've been through the steps that are listed in the article above the printer may require troubleshooting. You can reach support - 800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number. http://www.hp.com/cgi-bin/hpsupport/index.pl - for the maintenance options.

    Good luck!

  • HP Officejet 6600: problem with the printer or ink system

    I have a HP Officejet 6600. I replaced the black cartridge with a new HP black ink cartridge. This message keeps poping up, there is a problem with the printer or ink system. Turn the printer off, then on. If the problem persists, contact HP. It gives me as two solutions. Solution 1: Reset the product. Turn the product off, and then unplug the power cord. Plug in the power cord and then press the key to activate the product. I've done this three times. Second solution: contact HP support note the error code provided in the email (I looked and it does not give me one) then he says, supported to contact Hp. go to: www.hp.com/support. Needless to say that this message keeps appearing on the screen of the printer and I can't do anything with the printer. Can anyone help with an idea? Please, I beg you.

    Hey @popcorn101,

    Welcome to the Forums of HP Support!

    I understand that you get the error "printer failure: there is a problem with the printer or ink system' on the front panel of your HP Officejet 6600 e-all-in-one printer.". Thanks for the troubleshooting steps that you received before reaching out for support, including. Right now, you have completed all the troubleshooting steps available in your efforts to solve this error in accordance with the document of support here. The failure itself is probably due to a failure of the print head. The print head is the part that the cartridges will fit. It controls the "reading" of the cartridges and put the ink on the page. If the print head does not, then the printing within your product system has failed. In this model of printer print head is a non-replaceable. Therefore, the resolution is a replacement of the entire unit.

    I highly recommend at this stage that you contact our Technical Support telephone queue for discover hardware replacement options.

    HP technical support are available by clicking on the following link:

    Contact HP support

    (1) once the page opens, please select the country in which you are located. Then, enter your HP model number on the right.

    (2) choose the 'Contact Support' tab at the top and scroll down to the bottom of the page "HP Support - contact" to fill out the form with your details.

    (3) Once finished, click on the 'Show the Options' icon in the lower right.

    (4) Finally, scroll to the bottom of the page and select 'phone number.' A file number and telephone number will now fill for you.

    I wish you good luck going forward with this!

  • Configure the print format. 3522

    I was printing a user for a smart phone manual. After many false starts, I finally got exactly what I need.

    Print booklet, 2 pages of a sheet and automatic two-sided, so I got 4 pages on a sheet of paper from the manual pages are half size of 8.5 by 11.  I could print 16 manual pages at once on 4 sheets of paper.  Exactly what I needed. It would take 20 tries to do all the work. cut the leaves half everything was fine.

    Then disaster! failure of the printer. A call to Canon got a warranty replacement.

    But now I've lost configuration to print in the right format. I can't replicate the results and I'm only at half way through the job.

    Detach the printer, I have a piece of paper that has 2 pages of manual on one side and 2 more on the other side. If I run 6 sheets at a time get 24 pages of manual. I am totally impressed with the software that does so well.

    But now I've lost the recipe to select print settings. If anyone can help. Is there a manual for the printer that describes the implementation of ptoper?

    Ever grateful, assistance or guidance on the search for what do mean the different settings of the printer.

    Hi Charlie-NP,

    For the PIXMA MG3522 user manual can be downloaded from the site Web of Canon USA.  Please click here to access the page Brochures and manuals for the printer.  Once the initial download to your model page, follow these steps:

    1. Please select your language preference in the section 'LANGUAGE '.

    2 when manuals are displayed, please click on the series of manual MG3500 of use you want to download for the operating system that is located on your computer from the GUIDES AND MANUALS section. When you do, a red DOWNLOAD button will appear. Please click the box below the button DOWNLOAD, and then click DOWNLOAD to start the download. The time for the download process can vary depending on the speed of your Internet connection and the size of the file being downloaded.

    I hope this helps!

    It has not responded to your question or problem? Please call or write to us at one of the methods on the page contact us for further assistance.

  • printer is not working, "the print spooler service is disabled" when it is not

    Hello

    I received a message that my pc required for the loading of driver software for a new unknown device, although I had nothing added.

    Now, I find that my printer is not working.

    I tried to accept the "locate and install driver software" message, but it does not work.

    I tried to uninstall the printer driver so that I can reinstall them, but I get a message that the uninstallation was failure because the print spooler service is disabled.

    I checked the print spooler service is set to auto & seems to be on.

    Would appreciate any opinion appropriate for a no no very savvy tech.

    Thank you

    This could be the reason why you do not see the printer in the Control Panel, printers. Try this, go to control panel, printers, if you see the printer listed to remove it. If you don't see the printer, the service could stop, go to services then and click on "Restart the service" (blue link top left), then go back to printing, its listed hopely now and you can remove it (right click). Now try to reinstall the printer.

    If that doesn't work try the system restore, restore to a date when the printer works fine.
    System Restore: frequently asked questions
    http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

    Or try the intructions on the link from my previous post. on "how to clean the printer drivers? It is to change the registry, make sure you follow the instructions carefully. Back up the registry, you want to change.
    How to make a backup of the registry in Windows 7, Windows Vista and Windows XP?
    http://WindowsXP.MVPs.org/registry.htm
    Use method 2.

    WARNING: With the help of the Publisher of the registry incorrectly can cause serious problems may require you to reinstall Windows. Microsoft cannot guarantee that problems resulting from the incorrect use of Registry Editor can be solved. Use the Publisher of the registry at your own risk.

    How to use the registry editor in Vista and other Techniques
    http://www.Vistax64.com/tutorials/178285-registry-editing.html

    Information in the Windows registry for advanced users
    http://support.Microsoft.com/kb/256986

  • No communication between the printer and the Red computer on switch flashing printer does on every time I turn it off

    I get a message there is no communication between the printer and the computer. Printer is all-in-one HP Officejet 4315v. Have uninstalled and reinstall the software and unplug the USB port and plug it back. Repeated several times. Still no communication. Exclamation red light next to 'on' and green button 'on' butter is flashing all the time.

    You have a hardware failure of the printer.  Contact the manufacturer for support.

  • C1765 done yellow toner a printer roller noise rattling and the printer does not work

    Hear a clicking noise when printing.  Replaced the yellow toner and the rattling is still strong and the printer will not work.  The noise and the vibration felt on the new toner only occurs with the yellow toner.  What is happening, is the printer goes wrong.  "low density, yellow to replace the cartridge, printer restart" I just put in a new cartridge.

    Hello David,.

    Please post on the forum. According to the information you provided, it looks like you have a mechanical failure within the printer itself. This device is more compact and carriers Dell limited parts, the best option at this stage would be to replace the printer. It is the course of action we would take if the product is under warranty.

    Kind regards
    Joseph E

    #iworkfordell

  • 0x61011beb problem with the printer or the ink system? Please HELPPP!

    I just bought the HP Photosmart Plus printer and it keeps coming back:

    Failure of the printer

    0x61011beb

    There is a problem with the printer or the ink system. Turn the printer off, then on. blah blah blah.

    I rebooted, disconnected, out cartridges many times. I did a lot of things on sites like unplug and wait 60 seconds and then put cartridges back and nothing works! Help me understand this im out, so frustrated.

    Thank you!

    Your error code is a HARDWARE problem.

    Try a partial RESET

    from the home screen

    To access the Help Menu home/Idle screen, tap Control Panel 4 times in this order-

    Lower left (BL) / top left (TL) / BL / BL to the Support Menu displays on the Control Panel, and then press OK

    (press the arrow to the left, "home", arrow, the arrow back button back)

    then select

    Press Menu >

    Resets the Menu >

    Partial reset

    If this does not work, you will need a new printer.

    call 1800.474.6836

    You may be eligible for a free replacement. have your product serial number ready.

Maybe you are looking for

  • Bluetooth is not recognized on Satellite Pro A100

    I have a Satellite Pro A100 828 running Win XP Pro. He is supposed to have integrated bluetooth but when I install the bluetooth stack, a message appears saying peripheral usb has malfunctioned and is not recognized by windows. In Device Manager, it

  • Trying to find the Pavilion dm4-1165dx with Windows 7 64 bit

    While using my laptop it is stopped and tried to restart, but was unable to do so.  When I first turn on the HP splash screen will appear and then freeze.  If I turn it off and then turn on the HP splash screen appears and then the screen turns white

  • HP Pavilion 1167dx g7: start error PTXTT0-5M688G-XD015G-60QS03

    Laptop will not start, does not load the system recovery safe mode freezes also.

  • my product key cannot activate what I do

    I installed a copy of windows server 2008 R2. After you have entered the activation key, it always says not activated. i diagnostic tool run. Here is the result. Please tell me is the windows now activated or not, advice me on what to do. I used two

  • trigger

    Hi all I am currently working on the inspection of labels using the vision. It is necessary to open and close each loop camera? I want to configure the camera triggering mode once and start getting the nod to each trigger. Anyone can please modify th