detection of windows windows 8 previus Setup

Similar Questions

• Satellite L40 - 14N: problem has been detected and windows has been shut down

  Help.

  My laptop worked perfectly well until my son used last night and went on various games.
  Since then when you turn it on, it is a blue screen that says: "a problem has been detected and windows has shut down to prevent damage to your computer.

  He said that he has downloaded something or added a new hardware or software.
  So, off it and tried.
  Have tried everything to make it work. tried to get into F8 and F12.

  Tried from the safe mode and the recovery disc tried following all the resulting instructions always blue screen.
  Not knowing what else to do. I have

  s he Knackared now?

  As I got the BSOD appears also after the use of the disk recovery and after a fresh install of the OS.
  Is this right?

  Unfortunately, buddy, but sounds more like a hardware problem as a problem related to sound.

  I would contact a technician for laptop and organize an audit of the material.

• How to detect the window closing event and to do some tasks before leaving

  Hello

  Someone knows how to detect the window closing event and to do some tasks before leaving?

  Sridhar

  Structure of the event allows to detect the window closing event. In the structure of the event,.

  Select this VI-> close round table for this task. See attached picture.

• "A problem has been detected and Windows has shut down to prevent damage to your computer"... * STOP: 0x0000007e (0x805c49b8, 0xf7a172b4, 0 x 80000003, 0xf7a16fb0)... blue screen

  Hello!

  For the life of me I can't figure out how to get my machine to boot successfully. Nothing changes when I choose Safe Mode, last known good Configuration, enable VGA Mode, booting, Directory Services Restore Mode or Debug Mode logging.

  It's very stressful, because I'm right smack dab in the Middle a semester at the College. I have most of what I currently need access to supported illuminates... but not quite all :( It is also very reassuring to be able to take care of the school of work away from the library of the University. Yesterday, my computer was working fine... I think that Windows has completed an update, if I can't remember now. As I woke up this morning, I was not able to boot all the way to Windows only once.

  My laptop is a HP Pavilion dv6000 running XP Media Center, and I have not installed new hardware since I bought the machine about 3 years ago.

  Here are more details, where they can help in the diagnosis of my problem:

  • ID of the system board: 30BB
  • Type of processor: Genuine Intel(r) CPU T2250
  • Processor speed: 1730 MHz
  • Total memory: 1024 MB
  • Video memory up to: 128 MB
  • BIOS version: F.06

  Here's the entire message to the blue screen:
  - - - - - - - - - - - - - - - - - - - -
  A problem has been detected and windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

  Make sure you have enough disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video cards.

  Check with your hardware vendor for updates to the BIOS. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select Safe Mode.

  Technical information:

  STOP: 0X0000007E (0X805C49B8, 0XF7A172B4, 0 X 80000003, 0XF7A16FB0)
  - - - - - - - - - - - - - - - - - - - -

  I also learned to a blue screen that says something about "PAGE_FAULT_IN_NONPAGED_AREA". I think that this happens when I try to start safe mode.

  Also, I never did much with computer problems beyond what could be repaired with the restoration of the system... so not being is not able to boot at all me has to stop. Please, I beg you! Help me?!

  With great appreciation for your time,.
  Damaya

  Quick suggestion

  Some HP partition the hard drive. have you tried to type F11 or F12 during startup (before that he go to the option mode start screen)? It might take you for a HP recovery program in that partition (because windows don't be loading not to use that recovery)
  Good luck

• my Iphone is only detected by Windows, not Itunes more

  Hello
  I have the problem, it was presented after that I stopped and restarted the Apple Mobile Device service...
  I'm on Windows XP

  I did this operation because my Iphone 4 was not detected by windows, but only by Itunes,
  and given that this message is popping up (several times in a short period of time) the opposite happening, my Iphone is only detected by Windows, not Itunes more...

  My antivirus occurs Kaspersky Pure, no malware or virus... I scanned my computer and corrected the registry problems using RegCure which was supposed to fix this error (0xc06d007e), but I still get the error message no matter what...

  If you have a solution or advice, I would be very grateful,
  Thank you

  Hi manuelfrulio,
   
  Follow the suggestion given in this link to fix the issue:
  iOS: device not recognized in iTunes for Windows
   

  If this is not enough, you may need to contact Apple Support Forums for assistance.

• Problem has been detected and windows has been shutdown error STOP: 0x0000008E. Get the memory dump after you have installed the trial version of MS Project 2010.__space.

  Original title: problem has been detected and windows has been shut down. Get the memory dump after you have installed the trial version of MS Project 2010.__space.

  Computer Message: Check if you have enough disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video cards.

  Check with your suppliers of material, updates the BIOS. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to start advance startup options, and then select Safe mode.

  Technical information: * STOP: 0x0000008E (0xC0000005, 0x8054556C, 0xADB78A98, 0x00000000)

  Beginning physical memory dump

  Total physical memory dump. Contact technical support for further assistance group.

  Hi fernandomventura,

  Step 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...) Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

  Step 2: Follow the steps mentioned in the articles below which deals with a similar question

   

  General troubleshooting for an error message that you receive randomly in Windows XP: "Stop 0x0000008E"-restore the system to achieve ".

  http://support.Microsoft.com/kb/945658/

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• CD/dvd drive not detected by windows

  my reader of cd/dvd in my computer hp laptop dv6000 is not detected by windows. It is powered, both the BIOS and Device Manager detects it, but windows doesn't

  IM on Windows Vista Home Premium.
  I had this problem before and I managed to fix it by unplugging and reconnecting the Cd/dvd drive (nothing to lose, no more warranty), but after doing a system restore, the problem resurfaced again.

  The hard drive is a Toshiba MK1637GSX ATA Device
  I tried to use the pages of Microsoft support without success. I have no upper and lower filter.
  I already tried with also Device Manager nothing doesn't.

  Help, please!

  Hello

  Please start from the top and do it, even if you've done it before as is often the
  all operations which solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack.

  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Old hard drive PS3 by USB box not detected by Windows Vista

  Hello

  I recently updated my old HD PS3 40 GB with a 500 GB one. Since then, I bought an external HD for my old HD, in the hope that I could use it as a hard drive for some files I have. However, I encountered a big problem - Windows Vista does not detect the HD.

  So far I read a lot of posts on the internet with people having similar problems, but with no definitive answer, so I hoped to get :)

  So far, I've tested the speaker on both the different 40 GB and new 500 GB PS3 in HD, as well as 2-3 computers. Nor are detected by windows... both have the power (green light is on, and I can hear the disc rotation), but are not detected on the management of the devices or programs in 3rd (SwissKnife). As far as the computer is concerned, nothing is connected.

  Thinking that it was probably a hardware problem, I whipped my laptop HD out and connected on a separate computer and it worked without me even having to he invites. This leads me to believe that the device works perfectly and its something about the PS3 HD, who doesn't like Windows.

  The only thing I have not tried is put my old hard drive to the PS3 in the PS3 and reformatting. The only reason for this is a screw on the case of the PS3 has decided, that he's not budging despite all my efforts. Its now 12:45 and I'm too tired to fight with 1 screw more! :) I really don't know not how tabling in so well, 3 others went fine and I deliberately don't screw them in tight with the new HD after I read about the problems people have had by removing the screws.

  Someone at - it suggestions at all? How to get Windows to recognize that this has something plugged in, on how to remove that last screw embarrassing! Whatever that either would be appreciated!

  Thanks in advance

  Hello
   
  Check if the drive works very well with the game station.
  Chipset driver update and see if that makes a difference.
   
  Check if the HARD drive is detected in the Device Manager or disk management tool.
  1. click on start, type devmgmt.msc and press to enter.
  2. from the list of issues, expand disk drives and check the sub for its detection.
  1. Click Start, type diskmgmt.msc and press to enter.
  2. check if the HARD drive is detected.
   
  If the HARD drive is not detected, try the next step.
  Step 1: Connect the HARD drive to the computer and find the hardware check if it detects. To do this, try the following steps.
  1. click on start, type devmgmt.msc and press to enter.
  2. from the list of items, click drives.
  3. click on the Action menu, and then click check for material changes.
  4. follow the wizard to complete the task.
  5. If there is no progress, then click the Action menu and click Add legacy hardware to install the device.
   
  Post back with the results, so that we can help you further.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• When I turn on the computer, the screen indicates "a problem has been detected and windows has shut down to prevent damage to your computer.

  Original title: when I turn on the computer.

  the screen shows "a problem has been detected and windows has shut down to avoid damaging your computor.

  Hi Cjdaniello,

  ·         Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Step 1: Start in safe mode and check if the problem persists.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2: If the problem does not occur in safe mode, you can put your system to boot (in normal mode) to solve the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  I hope this helps.

• My dell inspiron 1420 built in webcam is not detected on Windows Vista

  Title: original webcam not detected

  My dell inspiron 1420 built in webcam is not detected. I think I might have deleted a program associated with. I tried to reinstall the driver using the given cd but I get an error message. Please help :) thank you.

  Hello

  What is the full error message that you receive?

  Method 1: You can run the fixit available in the link below and then check if it makes a difference

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2: You can see the steps described in the Dell link below

  Webcam does not work

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?c=us&CS=19&docid=266612&l=en&s=DHS

• Call the scam; Error message "fault had been detected between windows 7 and Chrome.»

  * Original title: is 1866 324 6719 call a call scam?

  I was working in Chrome and suddenly the computer started beeping wildly and I got a message that a malfunction has been detected between windows 7 and Chrome.  IT gave a number without charge 866 to call and said not to stop the computer or my operating system is compromised.  And it will allow me to close the window chrome.  My gut says it of a virus, but want to be sure before we do anything.  Course of windows essentials security scan now.

  It's a scam call caused by malicious software (which is a nuisance rather than a threat). Do not call this number and in no case give some foreign to your PC access.

• Peripheral hardware devices - don't work or are not detected in Windows.

  Hardware devices do not work or are not detected in Windows.

  I have exactly the same problem. Is the returned message the Microsoft FixIt. No further details given. Nothing seems to be more information on the problem other than the claim that we exist.

• The Setup program cannot find the installtion languages in C:\ Windows\SysWOW64\InstallShield\SETUP. COVER file. Error 105

  I am trying to install a HP printer.  When I run the setup.exe and click the install, I get the message:

  Setup initialization error

  The Setup program cannot find the installtion languages in C:\ Windows\SysWOW64\InstallShield\SETUP. COVER file.

  Error 105

  When I do a search for the error message I get no results.  So I ask the community if there is a fix or work around this issue.

  Hello

  What version of windows you are using?

  The program is not compatible with your version

  List of limitations in 64-bit Windows
  http://support.Microsoft.com/default.aspx/KB/282423#appliesTo

  To run the troubleshooting program compatibility Troubleshooter

  1. Open the troubleshooting program compatibility Troubleshooter by clicking the start , and then clicking Control Panel. In the search box, type troubleshooting tool, then clickTroubleshooting. Under programs, click on run programs for previous versions of Windows.

  2. Follow the instructions contained in the resolution of the problems.

• HP v125w 2 GB drive flash not detected by windows

  My flash drive is not detected by windows what should I do

  I have a HP v125w 4 GB flash drive that works on Windows 2000 and 7.  However, I also have a disk 16 GB flash of v125w HP which works on Windows 7, but was not recognized by my system Windows 2000.  Here's what I did to get Windows 2000 to recognize (this may not work for everyone, but it did for me).

  I plugged the flash drive to 16 GB on a Windows 2000-based USB port and ran:

  Norton SystemWorks-> Norton Utilities-> find and correct problems->

  Norton Disk Doctor-> diagnosis

  that gave me the message:

  Insert the diskette to diagnose in the E: drive.

  So, I ejected the flash player, it plugged into the USB port and you click on diagnose again.

  Norton Disk Doctor consulted the flash drive, diagnosed and gave the following report:

  There is no problem detected on drive E:
  Partition table... Jump
  Structures of files... Ok
  Surface test... Jump

  After this, the flash player was working fine on my Windows 2000 and Windows 7 computers.

  Thus, this procedure is awakened somehow the reader as much as to be recognizable by Windows 2000.  I hope this helps you.

  Bob.

• Brother printer has not detected by Windows 7 64 bit.

  Brother DCP145C has not detected by Windows 7 64 bit. What port is recommended for the local printer - LPT1? Windows 7 should detect when the USB connection, but there is no activity. Similarly, the mode to scan on the printer is not responding to "check connection". Thank you.
  Checked the port LPT1 and COM on Device Manager and seem to work correctly. No updated driver needed updated port.

  Hello Richard,.

  If several USB devices are plug-and-play, printers need a print driver to work even on a USB port. I went to the Brother website and a research on the model of printer "DCP145C" increase any responses - are you sure the model number of the printer (not the part number)?

  You have a printer disk supplied with your printer? If you do, try to use that to install the print driver. As far as LPT1 goes, is for a printer with a parallel port (printer), and the COM ports are for those who use the ports series.

  Thus starts with the right model number and look for brother.com right print driver (or use the disc that came with the printer). Try and see if that solves the problem for you.

  Let me know how you fare.

  Kind regards

  BearPup