device not recognized by Windows

Similar Questions

• USB device not recognized in windows 7

  USB device not recognized in windows 7

  Hi eyadOdetallah,

  -Is the issue specific to a particular USB device?

  -What software changes you did on the computer before the show?

  Follow the steps below:

  Method 1:

  Run the hardware and devices Troubleshooter to run the automated troubleshooting services.

  Open the hardware and devices Troubleshooter

  Disable and re-enable all the USB controllers.

  Method 2:

  This allows controllers to recover the port USB of his condition does not respond. USB controllers represent the USB ports in Device Manager.

  To disable and re-enable the USB controllers, follow these steps:

  a. Open the Device Manager.

  b. expand Bus USB controllers.
  
  Note that you have to scroll down to find this point.

  c. right-click on the first USB controller under Bus USB controllersand then click Uninstall to remove it.

  d. Repeat steps above for each controller USB is listed under Bus USB controllers.

  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

• Gamepad - "Device not recognized USB" Windows 7 32-bit

  I own an INTEX it-gpo2 plugnplay Gamepad... earlier it used to work well... but these last days, when I connect it to my pc an error indicating "USB device not recognized" I HAV changed the port, but it shows the same error... I HAV tried also to install the drivers provided on the cd, but it also won't work... someone please help...

  Hi ArkaBarman,

  This problem is usually caused due to hardware or driver related issues. I would like to know some information about this problem so that we can help you further.

  1. have you made changes on the computer before this problem?

  2 What problem confined to the joystick?

  3. have you tried to connect the gamepad on another computer?

  4. What is the model of the joystick number?

  I would suggest trying the following steps and check if it works for you.

  1. click on Startand then click Control Panel.

  2. click on system and Maintenance, click System, and then click Device Manager.

  Note If Control Panel is in Classic view, double-click System, and then click Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  3     in Device Manager, double-click on it to develop a 'Bus USB controllers', right click on the controller host, click "Uninstall" and click "OK".
  4. Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  Please respond with more information about this problem so that we can better help you.

• M - Audio Keystation 61es device not recognized with Windows XP

  Having bought just a M-Audio Keystation 61es plug-and-play and running XP service pack 2, the computer does not design it.  I see on the online forum that these are not recognized in Vista either... Help.  I tried to download the right driver update M-audio - still does not work.

  Hello MotherKim,

  Thank you for visiting the Microsoft answers community.

  What version are you running to XP?

  According to M-referencing, this device is compatible with Windows XP SP2 Home / Professional Edition ONLY.

  How do you connect your deivce? Take a look at this image.

  If you simply connect with the USB, the nYou must not do anything other than plug according to the user's guide.

  Hope this information helps Chris.H
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Not getting FireWire devices not recognized on Windows 7

  Recognition FireWire problems
  My computer with Windows 7 Prof 64 bit doesn't recognize firewire devices that I connect to it.  Device Manager displays the drivers 1394 work very well.  My WD external hard drive so my Sony HDR HC5 camcorder are more recognized when I plug them cold or hot plug. Two of them have worked very well for more than 2 years and now for some unknown reason, that they stopped just recognized on any of 3 firewire ports available in my new DELL Studio8000 PC with a firewire card Texas Instruments PCI with 2 firewire ports. I have replaced the cables, uninstalled the drivers and reinstall them without any result.

  Hi DMJ06,

  Thanks for your post.

  If the manufacturer indicates a hardware failure on the device, it is likely, it is accurate.

  If it does not work on any of your computers, it's a strong argument for their suggestion.

  I propose to repair the unit if possible.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• ThinkPad W520 Win7 Bluetooth device not recognized by Windows 7

  Hi all

  Just got my Thinkpad W520 4270 CTO with bluetooth installed. It was a work station BACK I installed Win 7 x 64 Ultimate on and I finally got all the drivers installed, but the bluetooth software says it is no BT device connected to my laptop. I checked the BIOS settings and confirmed that the BT is enabled. I even turned off, saved, then he helped turn. Hit the Fn + 5 combo does not trigger the light or no matter what 'Found New Hardware'. When the laptop starts first BT light flashes and the wifi led and the HARD drive activity light. I was not yet able to load another OS, but I download Arch Linux and BackTrack 5 to test to see that it is perhaps a problem with OS.

  Thoughts or ideas would be useful, it seems that my Google-Fu me has missed as well.

  EDIT: I realize in the sticky on the "do not update the bluetooth drivers" but I do not get my bluetooth to work at all, not even recognized by the operating system as an "unknown device".

  I thought about it. It is ridiculously easy. Download the drivers for the keyboard shortcut key and install. It allow you to use the functions at the top of your keyboard, and then after reboot, press Fn + F5 and will you will get a menu to activate the Bluetooth on the operating system, then Win7 should detect and install the drivers for it, or you can download those from the Lenovo site.

• USB device not recognized when I connect my iphone to my computer

  Original title: USB device not recognized

  I get the error message "Unrecognized USB device" when I connect my iphone to my computer.  It is the same as the one I use for months.  Same computer.  Same sync cable.  I have changed everything, including hang iphone to my wife instead of mine and get the same message.  I also did a restore on my computer that doesn't change anything.

  Hello

  At this point, I think it's a good idea to run a scan for viruses/malware on the PC with the anti-virus software that you have installed.

  Also, if you haven't already, I would try removing the USB controllers and restart again, now that the updates of Windows are installed. Don't forget, you can even download the drivers directly from manufacturer support site for your PC, if they install automatically when you restart after their removal.

  Finally, take a look at the thread I linked below. The first answer is quite similar to that mentioned above in this thread, but there are also a few other really good measures listed there as well. Then take a look at the linked thread and see if that helps at all.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/USB-device-not-recognized-in-Windows-7/8106a712-A13E-4ca5-b82e-c3961cc254b1

• Error "USB device not recognized", but nothing is plugged in and my webcam is not working. It says webcam not connected

  Error "USB device not recognized", but nothing is plugged in and my webcam is not working. It says webcam not connected

  Hello

  Since you said it worked very well recently, I'll try to do a system restore at this point in time.

  See this link: http://windows.microsoft.com/en-us/windows7/products/features/system-restore?SignedIn=1

  In addition, see the response of the Meghmala and follow the instructions listed there. I think that the three method might be the best of the bunch for you, but they have all the right steps.

  See this thread: http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/usb-device-not-recognized-in-windows-7/8106a712-a13e-4ca5-b82e-c3961cc254b1

• Device not recognized-to USB using Windows XP (sp3)

  The camera is on, I did not USB drive internal or external, the USB cable is a direct connection with the camera and the computer. I am running windows XP; I even tried on another laptop and at the end upward with the same message-USB device not recognized! This could be a software problem on the camera, or a bad set of USB cables? The camera is 2 years old and the cable have used about 6 times to transfer photos from the camera to the computer. When I tried on another laptop I got the following message: not properly installed device driver software! Is there a solution to this problem?

  Hi RigoSantiago,

  Follow these methods.

  Method 1: Install the drivers for the camera and associated software. Also, see the manual for more information.

  Method 2: Follow the steps in the article.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  USB devices that are disconnected and then reconnected to a USB hub may not be detected on a Windows XP-based computer

  http://support.Microsoft.com/kb/920875

  For reference:

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive

  http://support.Microsoft.com/kb/925196

  Why my computer does not detect my new USB device when I run Windows XP or Windows Server 2003?

  http://support.Microsoft.com/kb/314634

• Windows 7 - "USB device not recognized" - to load the new electronic Cigarette device. Help, please?

  I have Windows 7 Home Premium.  I just bought a unit of the electronic cigarette, manufacturer is "Innokin Cool Fire IV", the usb charger plugged on Acer laptop and comes to the screen "USB device not recognized".  I loaded different brand before without problem, I don't know what to do and I am NOT GOOD WITH COMPUTERS!  My settings are at "install updates automatically" and I DON'T WANT WINDOWS 10!  Can someone help me please?  Thank you for taking the time to read this.

  This seems to indicate that the charger has actually been detected as a device, but Windows can not work it out.

  Normally such a device should only connect to 5v and 0v pins and have no connection with the pins of data, in this way, that it will not be seen by Windows. I would be concerned by the quality of the device if it has some form of data connection. If you want to continue with this charger, that I would recommend to use a power supply of 5v USB instead of risking the USB port of the laptop, a lot less expensive if it does not. It has been reported several eCig Chargers catch fire. Something like this:

  

• Wired controller Xbox 360 connects to Windows 7, error: USB device not recognized

  Original title:-wired controller Xbox 360 connects to Windows 7

  Hey, I recently bought a controller wired xbox 360. And it does not connect to my PC. When I try to connect it says device not recognized USB. And in Device Manager it says it is an unknown device and that "Windows has stopped this device because it has reported problems. (Code 43) "I downloaded the driver from the software http://www.microsoft.com/hardware/en-us/downloads here and I also downloaded the MotioninJoy as an emulator, but the xbox 360 controller does not always connect." Is there a way to fix this?

  Hello

  1. did you of recent changes to the system before the show?

  2. do you have the receiver for the device to the XBOX?

  Method 1: Troubleshoot your XBOX controller.

  Follow the steps in troubleshooting from the link below and check if it helps.

  http://support.Microsoft.com/kb/908888

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  http://support.Xbox.com/en-us/Xbox-360/troubleshoot/accessories/controllers-remotes

  Method 2:

  (a) click Start.

  (b) access Control Panel, click on System.

  (c) click on hardware, click Device Manager.

  (d) open Device Manager and expand the devices with error code 43.

  (e) right click on the device and Uninstall the device.

  (f) restart the computer.

  Check to see if that fixes the problem.

  If the problem persists, I suggest that you follow the XBOX support link below for assistance.

  http://support.Xbox.com/en-us/

  In addition, check out the link below and check if it helps.

  http://support.Xbox.com/en-us/Xbox-360/troubleshoot/hardware/error-codes

  It will be useful.

• My WebCam Studio H.D 1080 p is not recognized by Windows Live Device Manager?

  Lately, I have installed Microsoft Studio Webcam H.D 1080 p. However, there are pop up messages saying that your LifeCam is not recognized by Windows Live Device Manager and load it down.  That's why I can't use IM, Vedio call etc. The pilot is the most recent.  Could you please identify the problem and fix it if tha I can't deal with the problem?

  Hello

  ·         Have you installed latest LifeCam Studio Firmware update?

  ·         What is the exact error message?

  ·         Were there recent changes made on the computer before the show?

  Follow these methods and check if that helps.

  Method 1:

   

  Run the Microsoft fixit tool and check if that helps.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/

  Method 2:

   

  I suggest you to uninstall the drivers from the Device Manager and reinstall the latest drivers and software for webcam on the Microsoft site and check if it helps.

  http://www.Microsoft.com/hardware/en-us/p/LifeCam-Studio#support

   

   

  Method 3:

  Follow the steps in the article, and check if that helps.

  With the help of your LifeCam with Microsoft Live Messenger

  http://support.Microsoft.com/kb/921332

  See also:

  Support for Microsoft mouse, keyboards, LifeChat, LifeCam & more

  http://support.Microsoft.com/ph/7746

• Device not recognized USB keeps popping up - Windows 7

  I have been using a wireless keyboard with the Sony Vaio laptop with Win 7 64 bit for a year and, yesterday, the keyboard no longer works.  The keyboard works fine with 2 other laptop computers (Win7 and XP).  Even when I unplug the dongle, the message "USB device not recognized" keeps popping up ever minute or more.  All other USB devices (i.e., memory keys, portable HDs, etc) work very well.  I uninstalled all the USB controllers in Device Manager and rebooted (multiple times).  I tried to go back to a system since a couple of days restore point.  Nothing solves the problem.

  I wish that the keyboard to work again, but also really want the message stop appearing.

  Thank you.

  Thank you for your advice.  I tried all these.  None worked.

  Suggestions posted another user, I completely turned off my Sony notebook; has out the battery. waited a few minutes; restarted and viola - no more boring don't pop up error message, no error in Device Manager and I use the USB keyboard Adesso WKB-3000 wireless key in the response.

• Stor.e slim not recognized by Windows 8.1

  Hello

  A Stor.e slim external HARD drive is not recognized in Windows 8.1 (no problem with Windows 7). When it is plugged in, it s shown as a device not recognized. Driver is requested but not found.

  Hello

  Stor.E Slim external HARD drive is a 2.5 HDD USB 3.0 and 900mA power it requires to work correctly.

  I suppose that there is nothing wrong with this HARD drive, but with your laptop.

  8/8.1 win requires different drivers and you will probably need to install a suitable driver in order to get the USB ports work correctly (USB 3.0 as well as the driver additional chipset would be also necessary).

• PRS-600 USB device not recognized

  I am unable to get ereader PRS-600 to be recognized by the computer (Win7).
  I tried to update the software (even if I think it's in)
  (date) but the window 'connect a PRS-600 to update' does not progress and the update button is dimmed.
  I deleted the "unknown device" in the drivers, but when I reconnect the USB cable and the ereader, I always get the display of device not recognized and the message "USB device not recognized".

  I seem to have solved the problem. I contacted Sony through esupport and a chat with a tech.

  Make sure that the battery has some charge inside. Completely charge if you can.
  Stop eReader (fully)
  Remove the SD card
  Press the button Reset (at the bottom of the ereader)
  Turn it on
  While the display shows "Open book", at the same time press the button to "turn the page" (back) and the Volume button until the "Reset All" + screen
  Enter 'Yes' to reset the ereader. You may need to configure the screen (X button with the tip to draw at various points)
  If you charge the battery, you may need to contact the support chat for sorting.

  Good luck!