M - Audio Keystation 61es device not recognized with Windows XP

Similar Questions

• USB device not recognized in windows 7

  USB device not recognized in windows 7

  Hi eyadOdetallah,

  -Is the issue specific to a particular USB device?

  -What software changes you did on the computer before the show?

  Follow the steps below:

  Method 1:

  Run the hardware and devices Troubleshooter to run the automated troubleshooting services.

  Open the hardware and devices Troubleshooter

  Disable and re-enable all the USB controllers.

  Method 2:

  This allows controllers to recover the port USB of his condition does not respond. USB controllers represent the USB ports in Device Manager.

  To disable and re-enable the USB controllers, follow these steps:

  a. Open the Device Manager.

  b. expand Bus USB controllers.
  
  Note that you have to scroll down to find this point.

  c. right-click on the first USB controller under Bus USB controllersand then click Uninstall to remove it.

  d. Repeat steps above for each controller USB is listed under Bus USB controllers.

  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

• Gamepad - "Device not recognized USB" Windows 7 32-bit

  I own an INTEX it-gpo2 plugnplay Gamepad... earlier it used to work well... but these last days, when I connect it to my pc an error indicating "USB device not recognized" I HAV changed the port, but it shows the same error... I HAV tried also to install the drivers provided on the cd, but it also won't work... someone please help...

  Hi ArkaBarman,

  This problem is usually caused due to hardware or driver related issues. I would like to know some information about this problem so that we can help you further.

  1. have you made changes on the computer before this problem?

  2 What problem confined to the joystick?

  3. have you tried to connect the gamepad on another computer?

  4. What is the model of the joystick number?

  I would suggest trying the following steps and check if it works for you.

  1. click on Startand then click Control Panel.

  2. click on system and Maintenance, click System, and then click Device Manager.

  Note If Control Panel is in Classic view, double-click System, and then click Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  3     in Device Manager, double-click on it to develop a 'Bus USB controllers', right click on the controller host, click "Uninstall" and click "OK".
  4. Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  Please respond with more information about this problem so that we can better help you.

• EliteOne 800 G2: EliteOne 800 G2 NIC driver not recognized with Windows Deployment Service WDS

  Hello

  I have just taken receipt of 5 new HP EliteOne 800 G2 23 "no touch machines. All PC's are generally imaged using Windows Deployment Services.

  I downloaded sp72515.exe that is the Intel I219 NIC driver pack for Windows 7 64 bit and injected these drivers into Windows Deployment Service and updated the boot LiteTouchPE_x64.wim file. Windows reported it went slowly and the 6 drivers concerned are all showing loaded with so much success in WDS.

  

  

  Problem. When I PXE boot the Windows EliteOne 800 G2 pilot of the CARD is not recognized by the 800 EliteOne G2.

  Wizard error

  A connection to the deployment share (\ < servername > \Deploymentshare$) could not be made. The following network device did not have a driver installed. PCI\VEN_8086 & DEV_15B7 & SUBSYS_8058103C & REV_31

  Hello:

  The only suggestion I can offer would be to try the driver directly from Intel...

  The 2nd file listed on the left side of the page is for W7 x 64.

  https://Downloadcenter.Intel.com/download/18713/network-adapter-driver-for-Windows-7-?v=t

• device not recognized by Windows

  Hello

  I have a problem with my camera, I saw a lot of posts here of a similar question, so do not know how to see that I have not seen any solution.

  When I connect my camera to the USB port, Windows will try to install the drivers but complain that the device is not recognized.

  I can see new driver added to 'my computer' under memory card format, but it is not accessible

  If I try to delete the driver of drivers installed, it will reinstall with the same problem

  If I connect using tips I've seen here (hold down and press the Center button) it will be recognized, but only for this session, moreover, when I do, I can't see or delete songs I've stored there before, but I can add new songs.

  In any case, I can play those songs.

  The format of the device or reolve somehow?

  On the device, go to

  Settings > USBMode > select MSC.

  That will force a permanent connection of MSC. You will not see the content of the PSG. First, you could reformat and start over.

  Go to settings > Format > select Yes

  I advise you to update the firmware while you are here.

• Not getting FireWire devices not recognized on Windows 7

  Recognition FireWire problems
  My computer with Windows 7 Prof 64 bit doesn't recognize firewire devices that I connect to it.  Device Manager displays the drivers 1394 work very well.  My WD external hard drive so my Sony HDR HC5 camcorder are more recognized when I plug them cold or hot plug. Two of them have worked very well for more than 2 years and now for some unknown reason, that they stopped just recognized on any of 3 firewire ports available in my new DELL Studio8000 PC with a firewire card Texas Instruments PCI with 2 firewire ports. I have replaced the cables, uninstalled the drivers and reinstall them without any result.

  Hi DMJ06,

  Thanks for your post.

  If the manufacturer indicates a hardware failure on the device, it is likely, it is accurate.

  If it does not work on any of your computers, it's a strong argument for their suggestion.

  I propose to repair the unit if possible.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• ThinkPad W520 Win7 Bluetooth device not recognized by Windows 7

  Hi all

  Just got my Thinkpad W520 4270 CTO with bluetooth installed. It was a work station BACK I installed Win 7 x 64 Ultimate on and I finally got all the drivers installed, but the bluetooth software says it is no BT device connected to my laptop. I checked the BIOS settings and confirmed that the BT is enabled. I even turned off, saved, then he helped turn. Hit the Fn + 5 combo does not trigger the light or no matter what 'Found New Hardware'. When the laptop starts first BT light flashes and the wifi led and the HARD drive activity light. I was not yet able to load another OS, but I download Arch Linux and BackTrack 5 to test to see that it is perhaps a problem with OS.

  Thoughts or ideas would be useful, it seems that my Google-Fu me has missed as well.

  EDIT: I realize in the sticky on the "do not update the bluetooth drivers" but I do not get my bluetooth to work at all, not even recognized by the operating system as an "unknown device".

  I thought about it. It is ridiculously easy. Download the drivers for the keyboard shortcut key and install. It allow you to use the functions at the top of your keyboard, and then after reboot, press Fn + F5 and will you will get a menu to activate the Bluetooth on the operating system, then Win7 should detect and install the drivers for it, or you can download those from the Lenovo site.

• Satellite A500 - 14K - key USB not recognized with Windows 7

  I have a Toshiba Satellite A500 14 K, it was pre-installed for Windows 7.
  I bought the upgrade to Windows 7: I got a PC upgrade disk and a windows upgrade disk. I launched the first disk, then the other.
  There was no particular error in these facilities.

  Since this upgrade, my PC doesn't recognize USB keys while they work perfectly with the previous version of windows with this pc. They are normally key usb plug-and-play. When I launched the update of windows, the driver exists, but installation failed in error with a message of access problem.
  I check that the firewall does not block access. I installed the latest version of the BIOS

  I can't find any similar pb on the forum
  Thank you for your help

  Hello

  Have you tried to update (restore) chipset utility?

  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp

• USB device not recognized when I connect my iphone to my computer

  Original title: USB device not recognized

  I get the error message "Unrecognized USB device" when I connect my iphone to my computer.  It is the same as the one I use for months.  Same computer.  Same sync cable.  I have changed everything, including hang iphone to my wife instead of mine and get the same message.  I also did a restore on my computer that doesn't change anything.

  Hello

  At this point, I think it's a good idea to run a scan for viruses/malware on the PC with the anti-virus software that you have installed.

  Also, if you haven't already, I would try removing the USB controllers and restart again, now that the updates of Windows are installed. Don't forget, you can even download the drivers directly from manufacturer support site for your PC, if they install automatically when you restart after their removal.

  Finally, take a look at the thread I linked below. The first answer is quite similar to that mentioned above in this thread, but there are also a few other really good measures listed there as well. Then take a look at the linked thread and see if that helps at all.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/USB-device-not-recognized-in-Windows-7/8106a712-A13E-4ca5-b82e-c3961cc254b1

• Error "USB device not recognized", but nothing is plugged in and my webcam is not working. It says webcam not connected

  Error "USB device not recognized", but nothing is plugged in and my webcam is not working. It says webcam not connected

  Hello

  Since you said it worked very well recently, I'll try to do a system restore at this point in time.

  See this link: http://windows.microsoft.com/en-us/windows7/products/features/system-restore?SignedIn=1

  In addition, see the response of the Meghmala and follow the instructions listed there. I think that the three method might be the best of the bunch for you, but they have all the right steps.

  See this thread: http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/usb-device-not-recognized-in-windows-7/8106a712-a13e-4ca5-b82e-c3961cc254b1

• Device not recognized USB message with iPhone 3g

  Here's the story from the beginning, I hope that I have provide sufficient detail.

  I got my iPhone 3 G is replaced. Therefore, a new phone... I went on iTunes in the middle of the restoration... It gave an error message and put my phone in recovery mode. Since my computer gives me the message "USB DEVICE NOT RECOGNIZED" and appears as an "unknown device" in Bus USB controller in Device Manager.

  I went to apple and they finished the restoration... I plugged the phone on other computers... It is therefore not the phone.

  Still nothing pops up... It keeps giving me "USB DEVICE NOT RECOGNIZED" I have uninstalled iTunes the right way... as Apple people walking through and reinstalled... the Apple Mobile Device is started.

  I still get nothing... everything is... newly installed... Windows doesn't recognize just... that it doesn't show up as a camera... and it does not even charge my phone.

  I tried different ports... and I get the same message... my camera and my sisters iPod shuffle connect correctly.

  I really need help! I don't know what else to do... I need to work on this computer. It's a Toshiba Satellite Windows Xp SP3

  I just went through two weeks of tampering with my 'old' computer trying to recognize my new 4370dn Canon multifunction printer after installing Windows 7.  I tried to reinstall Windows XP, uninstall the USB ports and hubs in Device Manager, update the printer drivers and several combinations of these elements.  In my case the ports would recognize external hard drives and flash drives, but my printer would come as a device not recognized.  Finally, what worked for me was to uninstall all the ports/USB hubs listed in Device Manager (they get automatically reinstalled with a soft reboot of the computer) again, download a driver from the Intel website (http://downloadcenter.intel.com/confirm.aspx?httpDown=http://downloadmirror.intel.com/16023/a08/infinst_autol.exe&agr=&ProductID=&DwnldId=16023&strOSs=&OSFullName=&lang=eng) chipset installation utility and restart the computer.  When I plugged the USB cable from the printer, the normal process of new device was launched.

• Problem of "USB device not recognized... "with syncing Treo 750

  "USB device not recognized - one of a mulfunctioned USB devices" - this sign always appears when I sync my Treo 750. After a few attempts WM Device Center finally can 'see' Treo and this sign disappears. What I supposed to do? Find a driver for Treo or what? Could someone help me please?

  In your 750, go to start > programs > USB to PC. There, you will see a check box. If it is not checked, check it, if it is checked, uncheck it. After that try to sync your device to your PC and let me know what happens.

  Message is about: Treo 800w (Sprint)

• Peripheral PnP USB - muted, is unplug sound when not touched, "device not recognized" or a malfunction, etc...

  Here is an exhaustive list I hope what happens (it's the Microsoft forums, so I think you guys are going to read a lot of information):

  • The sound on my PnP USB audio device cancels randomly without any reason. It is not to be touched at all, and often happens when I'm even not listen to all the sounds.
  • Before he died, it emits a blur in the helmet noise as it is to be disconnected or the cord is cut or something. I have to unplug it and plug it back several times to make it work.
  • It has been for several months, working properly, this month started anything, for about a week.
  • I can't use my headset because it is loose. I had the USB key to solve this problem, because it's too expensive get taking fixed. I did not buy the device at first hand, I got it from a family member who took my laptop in for repair and the guy he recommended and we sold two of these jacks.
  • When it goes off during a game, I can't sound to return. Sometimes I can fix it on a game (as Portal 2, for example) by going to options and change the type of sound (or any) what's called it headphones to speakers, then back to the helmet. However, the game freezes often when the sound goes off and I have to remove the usb key, and in this case the game should also be repeated. In addition, everything has sound options like that.
  • This happens randomly, but it tends to happen every five minutes or every few seconds, and coincidentally it almost always happens during a loading on a video game screen.
  • It is not always give me a warning sound, especially on the games. He's just quiet.
  • Device Manager does not display a point of exclamation or question marks next to any audio device and the key USB pnp is indicated correctly. In the options of the sound in the Control Panel, there is of the sound bars next to the USB key that indicates that his is read, but it is not in playback mode. The USB pnp is listed as default device, so don't tell me to do. The microphones are turned off as well.
  • It does the same thing in all my usb ports.
  • The driver is up-to-date and meant for Windows 7.
  • I do not install the Windows updates. Updates are bad.
  • Box for what he calls a "USB stereo Audio Adapter external" StarTech.com, or "ICUSBAUDIO". It came with a disc that I used to install the driver, and I went on their website to get one for Windows 7 specifically and installed.
  • I use a computer laptop 64 bit Windows 7. In Device Manager, there are three things listed under sound: Realtek High Definition Audio Intel (r) display Audio and USB PnP Sound Device. None of the USB devices have exclamation points.
  • For the first time today, when the usb unplug sound, my computer tells me "Device not recognized" and said it could have malfunctioned. When I clicked on it for more information, he said that he could not tell me what the usb was even because it was not plugged in, which was not true. I also had a window appears which has tried to install the device driver (already installed) and then was told that the unit had been disconnected before he could do (not true). It just happened, for the second time today a few seconds ago.

  Hello

  Check out the link and run the Fixit and check.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Install the Windows updates as some updates can fix a problem.

  As you mention that the computer is second hand troubleshooting accurately would be difficult. I suggest you contact the manufacturer. Check out the link.

  http://www.StarTech.com/support

• PRS-600 USB device not recognized

  I am unable to get ereader PRS-600 to be recognized by the computer (Win7).
  I tried to update the software (even if I think it's in)
  (date) but the window 'connect a PRS-600 to update' does not progress and the update button is dimmed.
  I deleted the "unknown device" in the drivers, but when I reconnect the USB cable and the ereader, I always get the display of device not recognized and the message "USB device not recognized".

  I seem to have solved the problem. I contacted Sony through esupport and a chat with a tech.

  Make sure that the battery has some charge inside. Completely charge if you can.
  Stop eReader (fully)
  Remove the SD card
  Press the button Reset (at the bottom of the ereader)
  Turn it on
  While the display shows "Open book", at the same time press the button to "turn the page" (back) and the Volume button until the "Reset All" + screen
  Enter 'Yes' to reset the ereader. You may need to configure the screen (X button with the tip to draw at various points)
  If you charge the battery, you may need to contact the support chat for sorting.

  Good luck!

• Satellite L30: Usb device not recognized

  I have a problem with my laptop L30.
  When I connect my phone or a flash drive or external hard drive, it is said: Usb device not recognized one of the usb devices malfunctioned.
  Tried to reinstall windows did not help...

  is there a solution?

  Hello

  Hmm. First of all, you should unplug all external USB devices.
  Then go to Device Manager and remove it all concentrators root USB and USB host controllers.
  Reboot the laptop.

  After this procedure, the operating system should recognize and should install new ports.
  Now you can connect to a plug - and play instruments. These devices should be recognized automatically. But some external USB devices need additional drivers.
  Usually these drivers are provided with the USB device.

  I would recommend this review if necessary!