DHCP for Wireless and Static IP for wired on WAG320

Similar Questions

• How to set up LAN wireless and wired for simultaneous operation

  I use a Lenovo thinkpad running windows XP. I want to set up an independent network so that I can connect my hardware for debugging. At the same time, I want to be able to access the corporate network using the wireless interface.  My autonomous network consists of a Belkin router that is to act as a DHCP server, my laptop connected to a port on the router and my test material connected to a different port on the router. My wireless interface is configured to connect to the corporate network. With wireless interface and the ethernet interface (wired) enabled, when I am doing a config ip, I see that the devices get valid IP address, corresponding to subnets, they connect to IE the ethernet port gets IP address 192.168.x.x 172.x.x.x IP poster wireless interface while. But I am not able to ping or access sites on the internet, I am able to ping the router Belkin on the independent network.

  However, if I go under network connections and disable the ethernet connection to the local network can access the internet and my business network. Similarly, if I disable the wireless connection and that you enable the ethernet connection, so I am able to ping the router only and not my test equipment connected on the same subnet.

  If I configure the (wired) ethernet network interface to use a static IP address in the pool of IP from the router Belkiin (who is also a DHCP server) and set the IP Address of the Belkin router as gateway, I can access all the other devices on this local subnet if and only if the wireless interface is disabled.

  The search for networks order is defined as the wireless and Ethernet.

  In my case, I need two interfaces to be active at the same time, as explained at the beginning. Appreciate any suggestions.

  Thank you.

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

  Hope this information is useful.

• My computer is constantly acquiring network address for wired connections and wireless.

  my computer is constantly acquiring network address

  my computer is constantly acquiring network address wired and wireless. Note my Dell inspiron B130, Windows xp 32-bit windows 8. also under the management of the network, the details are 0.0.0.0 IP address 0.0.0.0 assigned by dhcp and active ipv6 subnet mask. Thank you

  Hello

  1. what exactly is the problem?
  2. are you able to go online?
  3. have you made changes on the computer before this problem?

  The following articles can be useful if you are having a problem with internet connectivity.
  How to troubleshoot possible causes of Internet connection problems in Windows XP
  http://support.Microsoft.com/kb/314095
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• Wireless and wired router, DHCP and "visibility".

  Okay, it's a bit complicated, but I'll explain better than I can.

  I have a wired Linksys RV082 router. It works very well but is not wireless.  I have a Cisco/Linksys E2500 wireless router for my wireless devices to use.  the RV082 is the network of 192.168.1.x. The E2500 is the network of 192.168.0.x.  Cable Internet goes to the RV082 Wired, and a line out from there to the wireless router.  This all works fine except for a few disadvantages.

  I have an iPad that connects wireless and some of the apps offer a http:// option, so I can transfer files to this application.  I also have a network printer connected to wired and wireless devices do not.

  I have 2 problems:

  (1) in order to transfer files from my laptop (that I hung on the cable network most of the time), I disconnect the wire, wireless, then I can transfer files.  Œuvres, but it's embarrassing.

  (2) I want a netbook that I have on the wireless connection to print on my printer wired network.

  It seems that the 2 networks do not see each other.  Here are the things I've tried:

  (1) I disabled DHCP on the wireless router.  My thought is that requests for an IP address to the wireless router has sent will be transmitted along my wired router... NOT.  On my iPad and Wii, they could no longer connect wirelessly. Strangely enough, with the disconnected wire and wireless connection with my laptop, I've still was getting a 192.168.0.x IP address, even if the DHCP service is disabled on the wireless router.

  (2) thinking I would put manually the wireless router on the 192.168.1.x network, instead of saying things to get an Internet connection IP dynamicaly, I manually the IP value is 192.168.1.245.  Serious mistake.  I couldn't connect at all anywhere then.  The only way I could fix it was to hang on to my laptop computer, assign a static IP address to my laptop on the same network as the router, then I was able to get to the configuration page and to put things like he was.

  Another thing... Even when I'm connected only plugged on my laptop and wireless is disabled, I ping 192.168.0.1 (the wireless gateway) and it returns a value. But, when I try to go in a browser, I get a "page not found" error

  So, how can I get these two networks to play well and see each other?

  Thank you

  Jesse

  Put the router E2500 'bridge' mode and it will transmit the RV082.

  Assign E2500 DHCP, an IP address for itself of thje RV082, it will just be for access to the web administration E2500. System powered via the E2500 wired or wireless IP addresses will be obtained from the DHCP server on the RV082, and these will all be on the same subnet as designed to be plugged into the side of the RV082 LAN.

  Should allow you to do exactly what you want to do.

  I have a similar setup here works well with an E4200V2 right now.

• Separate Wired DHCP and static profiles

  Windows 7 Pro 64-bit

  We have two offices within our campus. Creating a server (DHCP, static) using DHCP. Although building B (DHCP, static) also uses the DHCP protocol, it is necessary for me to assign a static IP address to my PC for various reasons.

  I need to connect my PC to each building. Using another address is not viable because building B (DHCP, static) has DHCP so the PC is assigned to the DHCP rather than another static address.

  Can I create and select separate network for DHCP and LANs static profiles?

  Thanks in advance.

  You can watch NetSwitcher or NetSetMan...

  http://netswitcher.com/

  http://www.NetSetMan.com/

  .. .to create network specific profiles...

• Y at - it Windows 7 drivers for this wireless and bluetooth device?

  Have a DELL XPS 8700 with the following wireless and bluetooth chipset/map:

  Intel wireless Bluetooth 4.0 + HS adapter

  Intel Dual Band Wireless - AC 7260

  Are there drivers for Windows 7 64 bit for this chipset? Reason why I asked was when I tried to get DELL to install Windows 7 Pro instead of the Windows 8.1 on my machine, their excuse was that there were no drivers for these 2 items in Windows 7. I do not quite believe them.

  Having someone here "converted" Windows 8.1 (not pro) for Windows 7 and you have the mentioned chipset here?

  The guide says:

  The schema partition and target system type set as default system BIOS or UEFI computers MBR partition and can be used in most cases.

  In the rare cases where you need to install on a 3 to or more large drive with a SecureBoot/UEFI BIOS select GPT partition system for UEFI computers (I have not tested).

  So, if I did not need to install Windows 7 on a 3 TB drive, it will be better to disable the secure boot and UEFI to legacy? Or do I only in order to disable secure startup, but the setting UEFI?

  Reason why I ask, is that the other installation of Windows 7 guides you need to disable these two parameters, but in the guide you sendt me it seems that the only thing I should maybe change the start setting secure. Or maybe not?

• WIRELESS and wired LAN do not know each other

  My internet provider installed a new cable modem, without capacity WIFI because I have an airport extreme base WIFI (with cable Express extensions).  Speed and quality are OK, wireless and wired, but there seems to be a wall of China between WIFI and wired (LAN): devices that are connected via a cable to my LAN are not visible from the wireless network and vice versa.  Airport extreme is not 'Bridge' mode ("because not of wireless on the new modem capability".)

  No idea of the reasons for this?  Thank you very much

  Sounds like the configuration of the device. With the airport devices it can operate as a device on the network or another firewall as its own network. I think that it is way jumpered to activate, this will allow you to configure the wireless on the airport, but your current router will do the DNS/DHCP and will be a single network.

  Now that you have configured as two routers on an independent network as there is no bridge.

• HP Photosmart D110 - wireless and wired to installation - at the same time

  PLEASE READ CAREFULLY THAT NO MATTER HOW MUCH DETAIL I SAY QUESTIONS. IF ALL OF THE OTHER INFO. IS NEDDED IT PLEASE LET ME KNOW.

  Hello community I am undergoing, step by step, how can I set up my printer to a network via Wired and therefore any other device connected to that network can print from it.

  I used to have my printer connected via connected to my main PC, but it soon came the need to print from other places in my house and I remembered that my printer has this great ability, so I wanted to know how, step by step. I tried to put in place by myself, but I couldn't, I myself helped with the HP Solutions and Guides, and somehow, I missed something.

  Details:

  OS main PC: Windows XP 32-bit (it has the latest updates)
  Printer: HP Photosmart D110 one
  Router: Time Capsule from Apple

  I uninstalled the printer from my computer, so don't be any errors.

  Here's the deal, I want to connect my printer to my main PC via Wired (cable), once correctly installed, I want to connect this printer on my wireless (Network Time Capsule), so any other device connected to the network can print from it.

  If someone can take the time to tell me how to do, step by step, with links from HP information. etc if necessary.

  I already know how to set up a static for my printer IP address and all the stuff in IT, so don't worry, everything you say me that I understand it, all I need to know is what to do exactly, but the case is when (step by step).

  Thanks in advance.

  Hello, I noticed that you said 'Network via Wired' and then he said "wireless. I will be happy to help you. Just to let you know, you can't be WIRELESS and NETWORK CABLE (Ethernet). You can be wireless and plug the main PC into the USB cable. So, here are the steps to download the drivers and the connection to your PC (USB) PRINCIPAL and others (wireless).

  Connection to MAIN PC wired (USB)
  1. connect the USB cable from the printer directly to the main computer.
  2 download the drivers from the Web site (http://goo.gl/BVOOg), or if you have the CD.

  Note: whenever you download the software and drivers on the site. Be sure to choose the SOFTWARE from FEATURE COMPLETE.
  1. Select software and drivers
  2. type in the name of the product (click Search)
  3. choose the operating system (click Next)
  4. choose Download (scroll to the bottom for the SOFTWARE of FEATURE COMPLETE)
  5. After downloading the software, it will PULL
  6. it will give you an option on how you want that it connected
  7. you choose USB to the PC of the hand

  WIRELESS NETWORK connection
  1. go into your printer settings
  2. Choose Network
  3. Select wireless CONFIGURATION WIZARD
  4. it will search your router (if wireless). Choose your router and configure the printer wireless upward.
  5. go to other computers and follow the steps above to download the drivers.
  6. when it comes to SELECT connection, choose (without wireless/network)

  In this way, you can print from your main PC via USB (wired) and the other wireless computers.

  If your ROUTER is not wireless, and you can only use a wired (Ethernet) network, then you can print only by plugging the cable ETHERNET router to any PC of your choice print from the moment. Also to plug another cable from the router to the printer.

  I hope this helps, if you need more help please ask, thank you.

• Problems with HP Photosmart C309g wireless and wired

  Hello

  I fought with my C309g since I bought it a few months before.  It works on and outside, but can not hold a consistent network connection.  I have wired it usually but have tried both wireless.  It is plugged directly into my Netgear router.

  Before it works for a short period of time and the other Offline Online & on its own.  Sometimes it recognizes the other computers on the network to print & analyses.  I have 3 PCs on the network - two cables & a wireless.  It will recognize the three rarely, two of them sometimes, one of them sometimes (usually the laptop wireless) and none of these most of the time.

  There each time than in quite awhile for the first month and now it does not appear at all on the network - wired or wireless.  I can't print and more.  The documents simply to sit in Quebec for a while and then produce an error.

  Any help appreciated.  This printer is a wholemeal bread.

  Thank you

  Gringeiro

  Hi Gringeiro,

  You use the wireless WEP or WPA security on your router?  I would recommend WPA2 with AES, well, if you want to connect wireless.  It will also, if you set a static IP address on the printer.  You can do this by typing the IP address of the printer in the address bar of your browser.  Select the network tab, and then look for IPV4 under the section of wired or wireless, depending on how you have connected it.  There should be an option to "suggest manual IP".  If this isn't the case, type IPCONFIG from the command prompt (start/run cmd) to get your addresses in the subnet and the gateway.

• NAC L2 OOB VG Design for wired

  Hi all

  I need help of the NAC 2 OOB virtual layer for wired users design bridge . On Cisco documentation configuration only example is present, but it is for wireless users who is not applicable to my case (wired users); Here are the details; Please correct me if the design does not at any time;

  1: create a virtual local network (241) for the management of the CAM on the kernel.

  2: create a virtual local area network (240) for the management of CASES on the kernel.

  3: the IP addresses of both (10.10.240.1) E0 and E1 (10.10.240.1) for the CASE will be on the same subnet and same ip address.

  4: create all Trusted SVI's VLAN (vlan 10,20) on the kernel.

  5: configure manage subnets for vlan not reliable (100, 200) on CASES

  6: create a vlan mapping n/b approved and not approved (10 to 100, from 20 to 200)

  7: core connected to the CAs: E0, trunk allowed vlan 10, 20, 240

  8: core connected to the CAs: E1, trunk allowed vlan 100, 200

  9: another typical configuration

  I don't have a LABORATORY to test. I'm just confused if I missed something as implementation will be critical, and I'll try to avoid all risks.

  Please give me suggestion and best practices. Also please let me know if I need a config added?

  Kind regards

  Abdul Majid Khan

  Abdul,

  Port profiles are used to determine if a port is managed or not managed, so you will need at least a port profile. Here you can define what will be the VLAN initial of the switchports that the final VLAN will be etc etc.

  More details here: http://www.cisco.com/en/US/docs/security/nac/appliance/configuration_guide/48/cam/m_oob.html#wp1083087

  HTH

  Faisal

• ESXi 4.1 connection NIC 0 to NIC 2 to a Port DHCP and static IP address

  I have a Dell Blade M610 I recently put in place with ESXi 4.1 Software. I have the Management Console, NIC 0, a static IP address, but when I connect to a DHCP Port to NIC 1 I lose the ability to connect to the console of the VSphere Client. I get "connection failed". Remove the DHCP connection works and I can log in and manage the server.

  Question-

  What settings am I missing, that will allow me to connect it to a static IP Port and a DHCP Port at the same time?

  The static IP addressed Port is behind a firewall on a subnet to isloated. The DHCP Port is on the Production network. A point to note - while IP address static on an isolated network, the TCP/IP Port, which allows you to talk to the domain controller to add from the PC to the field, is open. Most of the other Ports TCP/IP is disabled.

  I would like to know if it is possible to realize that I need to create virtual machines to be used on the remote subnet, as well as on the Production side of the network.

  Is there a reason for the group "DHCP VMkernel" VMkernel ports on vSwitch1? If this is not the case, remove this port group. It is not necessary to connect to the network of the VM.

  André

• Questions to address IP DHCP for assistance

  Hello, I have a few questions about the dhcp ip helper address.

  Assuming that my router has two interface of FE (0/0 and 0/1). 0/0 0/1 has 10.1.2.1/24 and 10.1.1.1/24 a.

  0/0 via a LAN LAN switch connection has a DHCP of 10.1.1.5. There's no IP helper is configured on interface 0/0. Active DHCP server serves the 10.1.1.x dhcp clients.

  We are now adding 0/1 with 10.1.2.1/24 on the router. We want to have the dhcp service to clients on this new LAN site but we will not have another dhcp on the LAN Server, and we are not set up router interface to run the dhcp server on it either.

  Issues related to the:

  1. can I configure the IP helper of 10.1.1.5 on the FE interface 0/1 with 10.1.2.1 answer on that?

  2. If so, when the client on this new LAN sends dhcp broadcast to request ip address, will be the router on FE 0/1 'route' to FE 0/0 and the server 10.1.1.5 dhcp package? I read the IP address of said "before" assistance and I know if "step" = "road in layer 3" as well as the dhcp server is not connected to the FE LAN 0/1 switch. You are simply not sure if the DHCP server must connect to both switches LAN or not?

  3. I guess this means that the DHCP Server configures two set of pools and serves both sets of clients, right? (I want to just make sure that it is my first cope with dhcp).

  Thank you for your expert help.

  Hello

  Answers to your questions...

  Your installation is like this...

  Server (10.1.1.5) DHCP-{Fe0/0 (10.1.1.1) ROUTER or gateway Fe0/1(10.1.2.1)}

  Your 10.1.1.5 DHCP server is configured with two scopes or pools to assign IP addresses to the customer requests.

  Area 1: 10.1.1.0/24 with default gateway the 10.1.1.1 value option

  Area 2: 10.1.2.0/24 with option default gateway value 10.1.2.1

  a 3 - d. consider the request actually comes from a customer on the Fe0/1 interface. Support IP address is the router to forward DHCP broadcasts to 10.1.1.5 which is the DHCP server. While sending the request, she sees what interface, the application was received and it will identify the GIADDR field accordingly. So, in this case it affects 10.1.2.1 as he received Fe0/1 of the interface and the transfer of DHCP server.

  You have to think from the point of view of the DHCP server, how and what IP address should allocate to the clients requested different networks. After receving the request, DHCP server will find the scope or the pool from which assign IP address by comparing the GIADDR field in the query and brought local default gateway values. In this example, it will match 2 scope and assigns a free IP of this pool.

  3rd-4: Yes, you are right for the 3rd and 4.

  You are welcome with more questions :-)

  All the best...

  -Ashok.

• 802. 1 x EAP - TLS for wired users with ACS 5.5

  Hi all

  We are setting up a new configuration for wired users authentication with 802.1 x (EAP - TLS). ACS 5.5 we use as an authentication server.

  We have added the certificate (internal) CA root and certifcate for ACS signed by CA. Now, we want to check that authentication works or not. I hope that the CA root and identity certifcate also we need to install in laptop computers. But I don't know how to download the certifcates for client machine manually to CA.

  Please suggest on how to get certificates for clients both manually and automatically?

  Thank you

  Vijay

  Hi Vijay,

  for Wired 802.1 x (EAP - TLS) you must have the following certificates:

  Intermediate server on ACS - Root CA, CA certificate,

  The customer - Root CA, intermediate CA, user certificate (in the case of user authentication) or Machine certificae (in the case of authentication of the computer)

  I do not know what third-party certificate you use, if its Microsoft in the House or any other certificate server, you need to download the client certificate to the server itself.

  In the case of Microsoft, there will be a user certificate template. You can select and create user certificate

  This is an old document, but a computer certificate for the user configuration steps, you can see the steps to download the certificate user if his server from Microsoft:

  http://www.Cisco.com/c/en/us/support/docs/security/secure-access-control...

  In case you use the third serevr certificate, then you must check with them on how to download the certificate of the user

  See you soon

  Mohammed (rate useful message)

• Wireless and wired Internection connection problems

  Hello community,

  My first question concerns my wireless laptop connection (or lack of it). I rebooted my router (because I forgot my password), who restored the device to factory default settings.  When I've reconfigured the router, I was unable to connect to the Internet via a wireless connection. When I troubleshoot with Windows 7, it says that I need to connect an Ethernet cable from the router to the laptop.  However, it was not necessary when the connection to the local area network (LAN) via a public network worked without error.  In addition, when I check my wireless network connection, it shows that the signal strength is excellent and a connection is attempted, but without success.  When I open the network and sharing Center, there is no LAN.  Is it possible that something is blocking access to the LAN? It wasn't a problem, before I changed the router username and password the default user and password. Something is flooded with this situation.

  A second problem occurred when I tried to connect my desktop computer directly to the external modem from my ISP in which I work around the router. There is no Internet connection when this happened.  Before configuring the router via wireless connectivity, the direct connection between the external model of my ISP and my office worked without error. Your thoughts on these two issues are very popular.

  Thank you in advance.

  We're going to do in the first place the wireless and see if we can make it work.

  Go to the router configuration page (it can be www.routerlogin.com or an IP address, depending on your brand.) See your documentation for him.). Under "wireless" parameters must be a place to enter the password you will need to know to access the router. If it is always the default value (which will be probably if reset you factory default), then change to something unique.

  Open the network and sharing Center and click on 'Manage wireless networks' in the left column. Right click on your wireless connection and on the Security tab, select the settings of your router is to (WPA, WPA-2, etc.) and the type of encryption. Then enter the password that you put in the router in the box "network security key. On the connection tab, uncheck "automatically connect...". "for the time being. OK, and then restart. Check if your wireless network is working now.

  To connect to the modem, you may need to recover from the IP. Open a command window, type ipconfig/release and press ENTER. When that finished, type ipconfig / renew and press ENTER. Now you should be able to connect directly through the modem.

  Thing, that I forgot to mention, while you are in the configuration of your router, make sure that "Enable SSID Broadcast" (or a similar expression) is checked.

  SC Tom

• E2000 Wireless and help connect BEFVP41

  I have a VPN BEFVP41 router that I use for my home software company and I have several clients who need to access the files on my server... so the VPN endpoint router. And it works very well. However, I would like to connect my laptop, PS3 and DirecTV set-top satellite Internet and bought a wireless router Linksys E2000 for this.

  When I followed all the instructions, right out of the box, with all its parameters by default, I had wireless internet without problem, but did not have access to my network. I have live chat and was immediately referred to the helpline to help set up what they called a 'cascading connection '. Well, after almost 4 hours on the phone with them on 2 separate days, I now have no internet OR network connection on my E2000. It of a paperweight and sits right on the desktop. I tried to reset and start from scratch, as if I had just pulled out of the box... No, does not work.

  Is it possible to use an E2000 wireless router and connect to the internet through a wired router BEFVP41? If so, how? TIA

  PJO

  1. make sure that the BEF is working properly. I guess that's the address LAN IP 192.168.1.1 with subnet mask 255.255.255.0.

  2. it is probably best to reset the E2000 to the factory settings. Press reset for 30 seconds. Make sure that the E2000 is not connected to your network.

  3. wire a single computer to the E2000. Open the web interface at http://192.168.1.1/ on the main Setup page, give the address LAN IP 192.168.1.2 and disable the DHCP server. Save the settings.

  4. unplug the computer. Now one of the ports numbered from the E2000 LAN wire to the BEF. Do not use the internet port of the E2000.

  That's all. Now, you use the E2000 as a simple access point and ethernet switch. The internet-related functions are done on the BEF only.

  Don't forget to set up the wireless and secure the E2000 through its web interface to http://192.168.1.2/